Whitehall 6107 User manual

6107
Brand
Whitehall
Model
6107
Type
User manual

Whitehall 6107, your new lawn stake plaque assembly, offers a stylish and durable way to display your address. Made of hand-cast aluminum with a tough finish, it can withstand exposure to the elements and requires minimal maintenance. Installation is simple: dig holes, position the stakes, and tighten the screws. The plaque can be easily cleaned with a non-abrasive detergent and water.

Whitehall 6107, your new lawn stake plaque assembly, offers a stylish and durable way to display your address. Made of hand-cast aluminum with a tough finish, it can withstand exposure to the elements and requires minimal maintenance. Installation is simple: dig holes, position the stakes, and tighten the screws. The plaque can be easily cleaned with a non-abrasive detergent and water.

LAWN STAKE PLAQUE ASSEMBLY
INSTALLATION INSTRUCTIONS
TOLL FREE: 1-800-705-1446 WE CAN HELP!
signaturestreetscapes.com1-800-705-1446
LAWN ADDRESS
PLAQUE INSTALLATION:
A) Address Plaque
B) Lawn Stakes (1 or 2)
C) Screw Gaskets (2)
D) Hex Drive Cap Screws (2)
E) Flanged Hex Nut (2)
F) Allen Wrench (1)
HOW TO ASSEMBLE:
PARTS INCLUDED:
Push an O-Ring Gasket (C) onto the threads of
the Cap Screw (D) until it reaches the head of
the screw.
Position stake (B) on the back side of plaque
(A) so that the bottom of the plaque is resting
on the stake’s frontside shelf.
From the backside of the Stake (B), place the
Flanged Hex Nut (E) into the slot at the top.
Note: The hex portion of the hex nut should be
inside of the stake.
While holding the lawn stake (B) and Hex Nut
(E) in place, insert a Cap Screw (D) through the
hole in the plaque and thread it into the Hex
Nut.
Being sure the bottom of the plaque is resting
tight against the stake’s front shelf and that
the stake is perpendicular to the bottom of the
plaque, use the allen wrench (F) to tighten the
Cap Screw (D).
If your Plaque requires a second stake, Repeat
steps 1-5.
1)
2)
3)
4)
5)
6)
A
DC
F
E
B
SIDE VIEW
A
B
C
D
E
FRONTSIDE SHELF
(REST PLAQUE ON)
FRONTSIDE SHELF
(REST PLAQUE ON)
IMPORTANT NOTE! Plaque and Stake were not
designed to be driven into the ground. Please
follow installation steps below for optimum
results.
Dig holes 6” to 8” deep and place lawn
plaque stakes into the holes.
Check plaque for vertical and level.
Back fill holes and pack soil firmly down
against the stakes.
Whitehall Plaques are made of hand-cast
aluminum with tough finishes to withstand
exposure to the elements. To clean your
plaque, use a non-abrasive detergent and water
with a cloth, sponge, or soft brush. NOTE: The
simulated weathered bronze cannot be bright-
ened by polishing- This hand-painted finish
should retain its finish for many years without
special attention.
TO INSTALL:
1)
2)
3)
CLEANING INSTRUCTIONS:
  • Page 1 1

Whitehall 6107 User manual

6107
Brand
Whitehall
Model
6107
Type
User manual

Whitehall 6107, your new lawn stake plaque assembly, offers a stylish and durable way to display your address. Made of hand-cast aluminum with a tough finish, it can withstand exposure to the elements and requires minimal maintenance. Installation is simple: dig holes, position the stakes, and tighten the screws. The plaque can be easily cleaned with a non-abrasive detergent and water.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents