hyfire HFI-OM-240-01 User manual

HFI-OM-240-01
Brand
hyfire
Model
HFI-OM-240-01
Category
Fire protection
Type
User manual

The hyfire HFI-OM-240-01 is a device that can be used to remotely switch on or off third-party ancillary devices connected to a household mains high voltage line, such as A/C units, water valves, or lighting. It can be controlled by a fire security system's control panel and can be used in both hard-wired and wireless applications. In a hard-wired application, it requires a HFI-OM-RM-01 relay output mini-module, and in a wireless application, it requires a SGMCB-EOLM interface module and a HFW-BOM-03 wireless battery-powered output module.

The hyfire HFI-OM-240-01 is a device that can be used to remotely switch on or off third-party ancillary devices connected to a household mains high voltage line, such as A/C units, water valves, or lighting. It can be controlled by a fire security system's control panel and can be used in both hard-wired and wireless applications. In a hard-wired application, it requires a HFI-OM-RM-01 relay output mini-module, and in a wireless application, it requires a SGMCB-EOLM interface module and a HFW-BOM-03 wireless battery-powered output module.

GENERAL DESCRIPTION
The HFI-OM-240-01 is a device that switches on or off third party ancillary devices that are installed on an household mains high voltage line;
this device’s switch is controlled indirectly by the fire security system’s control panel.
The HFI-OM-240-01 can be used in a hard wired or in a wireless application context.
REQUIREMENTS AND COMPATIBILITY
The HFI-OM-240-01 must be used only in fire security systems based on the Argus Security’s wired and / or wireless protocol.
In a wired application the HFI-OM-240-01 requires a HFI-OM-RM-01 relay output mini-module.
In a wireless application, the HFI-OM-240-01 requires a SGMCB-EOLM interface module and a HFW-BOM-03 wireless battery powered
output module.
HFI-OM-240-01
Mains Line Switch Module
Hyfire Wireless Fire Solutions Limited - Unit B12a, Holly Farm Business Park, Honiley,
Warwickshire, CV8 1NP - United Kingdom
www.hyfirewireless.com
IMPORTANT NOTES ON WIRING
Place a disconnector on the mains line; the disconnector must be placed outside the installation
box, so as to be easily reachable. Disconnector’s contacts distance between each other must be of
at least 3mm.
Overcurrent protective devices (fuses, circuit breakers...) must be installed outside the installation box.
Refer to and follow national codes of wiring and cabling practice and other internationally recognized standards.
Apply scrupulously the instructions given in this manual, especially the safety warning notes and the wiring procedures.
Disconnect the household mains line from its power supply source, from the beginning to the end of the installation / maintenance
phases.
Make sure that the installation box, after installation / maintenance, remains sealed, preserving its original IP rating.
Mains line’s wires are intended to be connected only to their suitable terminal blocks.
Connecting these wires to the wrong terminal blocks will damage irreparably the HFI-OM-240-01 and be an hazard to final users.
Do not exceed maximum allowed loads on the household mains line.
Only competent and authorized personnel are allowed to access the installation box.
TECHNICAL SPECIFICATIONS
Analogue loop’s voltage range From 18 V (min) to 40 V (max)
Activated current draw from analogue loop 12.5 mA at 24 V
Operating temperature range From -30 °C (min) to +70 °C (max)
Humidity 95% RH max (no condensation)
IP rating (HFI-OM-240-01 only) 21C
IP rating (UA-BBOE-WFR-01 installation
box)
65
MAINS LINE LOAD SPECIFICATIONS
Allowed load types Resistive / inductive
Maximum allowed load
(RESISTIVE type)
5 A at 250 VAC
5 A at 30 VDC
Maximum allowed load
(INDUCTIVE type)
Power factor (cos Φ) = 0.4
L/R time constant = 7 ms
1.5 A at 250 VAC
1.5 A at 30 VDC
IMPORTANT NOTES ON INSTALLATION
HFI-OM-240-01 must always be installed into a suitable installation box.
You can choose between the UA-BBOE-WFR-01 wall box model, obtainable from your system supplier, or other suitable boxes
purchasable on the market. In any case:
- use only external boxes with a UL94-5V flammability class and
- cable glands must have a flammability class UL94V-1 or better.
Supply shall be provided by Limited Power source (LPS)
Picture 4 Picture 5
L20-VM240-14EN (vA.5) [email protected]
INSTALLATION
1. Fix the installation box in the planned location. If a UA-BBOE-WFR-01 is used, fixing screws insertion locations are highlighted in
picture 1.
2a. Wired application: Install the HFI-OM-RM-01 under the HFI-OM-240-01 module; be sure that the connectors under the
HFI-OM-240-01 enter properly into the HFI-OM-RM-01 female connectors (extractable terminal blocks must be previously
removed).
2b. Wireless application: install the SGMCB-EOLM under the HFI-OM-240-01 module; be sure that the connectors under the
HFI-OM-240-01 enter properly into the SGMCB-EOLM female connectors.
3a. If a UA-BBOE-WFR-01 is used, fix the HFI-OM-240-01 directly into the box: use the 4 supplied fixing screws (picture 2).
3b. If not using a UA-BBOE-WFR-01, fix the adaptor plate into the box; fixing screws insertion locations of the plate are highlighted
in picture 4.
Fix the HFI-OM-240-01 to the plate: use the 4 supplied fixing screws (picture 5).
4. Fit the cable glands into the entries of the box. UA-BBOE-WFR-01 is already equipped with knock-out holes for this purpose (picture 3).
5. Feed the cables into the box, giving them sufficient length for a secure connection.
6. Fix the loop cables to their suitable terminal blocks on the HFI-OM-240-01 (check the following wiring paragraphs).
7. Fix the mains line cables to their suitable terminal blocks on the HFI-OM-240-01 (check the following wiring paragraphs).
8. After wiring is performed, close the box and seal it with the provided screws.
9. Test the HFI-OM-240-01.
Picture 1 Picture 2
Picture 3
The UA-BBOE-WFR-01 wall box is designed with 12
cable entry knockout holes (6 M16/20 and 4 M25/32)
distributed on its sides; these entries allow sealed,
gland fitted cables to be introduced in the box itself.
CHECK INTERFACE DEVICE’S DOCUMENTATION
It is warmly suggested to read the installation manuals for the HFI-OM-RM-01, SGMCB-EOLM and HFW-BOM-03 interface modules to have
a complete vital knowledge of installation know-how for these devices.
Hyfire Wireless Fire Solutions Limited - Unit B12a, Holly Farm Business Park, Honiley,
Warwickshire, CV8 1NP - United Kingdom
www.hyfirewireless.com
LOOP IN (+)
LOOP IN (-)
LOOP OUT (+)
LOOP OUT (-)
1 2 3 4
Picture 6
HFW-BOM-03
24 VDC OUTPUT (+)
1 2 3 4
Picture 7
HFW-BOM-03
24 VDC OUTPUT (-)
ANALOGUE LOOP WIRING
HFW-BOM-03 WIRING
TESTING
Generate an alarm on the fire security system and check that the HFI-OM-240-01’s relay switches over from Normally Closed (NC) to Nor-
mally Open (NO), thus handling the output as per fire security system design.
In an hard wired application the control panel activates the underlying HFI-OM-RM-01’s output LED indicator (if enabled by the control
panel).
Hyfire Wireless Fire Solutions
Limited - Unit B12a, Holly
Farm Business Park,
Honiley, Warwickshire, CV8
1NP - United Kingdom
15
DoC-VM240
HFI-OM-240-01
For use in compatible fire
detection and alarm systems
L20-VM240-14EN (vA.5) [email protected]
HOUSEHOLD MAINS LINE WIRING
NORMALLY OPEN (NO)
COMMON (C)
3 2 1
Picture 8
NORMALLY
CLOSED (NC)
ALWAYS INSTALL THE SAFETY COVER
For safety reasons, the household mains line terminal blocks are equipped
with a detachable cover; if not working on these terminal blocks for installation
or maintenance reasons, ALWAYS KEEP THE SAFETY COVER IN-
STALLED IN ITS PLACE !!!
Picture 9
WARNINGS AND LIMITATIONS
Our devices use high quality electronic components and plastic materials that are highly resistant to environmental
deterioration. However, after 10 years of continuous operation, it is advisable to replace the devices in order to
minimize the risk of reduced performance caused by external factors. Ensure that this device is only used with
compatible control panels. Detection systems must be checked, serviced and maintained on a regular basis to
confirm correct operation. Smoke sensors may respond differently to various kinds of smoke particles, thus appli-
cation advice should be sought for special risks. Sensors cannot respond correctly if barriers exist between them
and the fire location and may be affected by special environmental conditions. Refer to and follow national codes of
practice and other internationally recognized fire engineering standards. Appropriate risk assessment should be
carried out initially to determine correct design criteria and updated periodically.
WARRANTY
All devices are supplied with the benefit of a limited 5 years warranty relating to faulty materials or manufacturing
defects, effective from the production date indicated on each product. This warranty is invalidated by mechanical or
electrical damage caused in the field by incorrect handling or usage. Product must be returned via your authorized
supplier for repair or replacement together with full information on any problem identified. Full details on our war-
ranty and product’s returns policy can be obtained upon request.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

hyfire HFI-OM-240-01 User manual

HFI-OM-240-01
Brand
hyfire
Model
HFI-OM-240-01
Category
Fire protection
Type
User manual

The hyfire HFI-OM-240-01 is a device that can be used to remotely switch on or off third-party ancillary devices connected to a household mains high voltage line, such as A/C units, water valves, or lighting. It can be controlled by a fire security system's control panel and can be used in both hard-wired and wireless applications. In a hard-wired application, it requires a HFI-OM-RM-01 relay output mini-module, and in a wireless application, it requires a SGMCB-EOLM interface module and a HFW-BOM-03 wireless battery-powered output module.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents