Gill Audio Lissa integrated amplifier Installation guide

Brand: Gill Audio

Model: Lissa integrated amplifier

Type: Installation guide

INST ALLATION AND OPERATING MANUAL

4 GR EA T VI EW AVE NU E N O RTH. PROV ID EN CE , RI 02 90 4 4 0 1 . 2 2 6 . 5 2 9 9

We appreciate your choosing the Lissa integrated amplifier. It is an excellent,

well designed, and built piece of audio equipment. It will provide you with

many years of listening enjoyment. We take great pride in our work.

Please be sure to read this manual prior to installation and use.

OPERATION INSTRUCTIONS:

UNPACKING:

When removing the Lissafrom the shipping carton, care must be taken.

Use a sharp knife to carefully open the box, being careful not to extend the

knife into the box. Once the box is opened, the packing material may be

removed. The Lissa integrated amplifier may then be carefully removed from

the box. Please pay attention to the faceplate. Do not contact the faceplate

or the switches with other objects. The switches may break.

4 GREAT VIEW AVENUE NORTH. PROVIDENCE, RI 02904 401.226.5299

WARNING:

The Lissa is heavy. Care must be used

when lifting and positioning it.

4 GREAT VIEW AVENUE NORTH. PROVIDENCE, RI 02904 401.226.5299

OPERATION INSTRUCTIONS:

CARE:

The Lissa is made from heavy gage powder coated steel with an anodized or

chrome plated faceplate. The unit is best cleaned with a damp cloth, but the

faceplate may be polished with an appropriate metal polish and the main chassis

polished with an automotive wax. Care must be take not to allow either pol-

ishing dust or particles to enter into the unit through the vent holes.

Opperation:

Once the Lissa is properly connected to power, source, and your speakers, it may

be turned on using the “POWER” switch. To avoid source turn on noise, it is best

to turn the Lissa on after the source is powered and off before the source is turned

off. The LED above the switch will light when the power is on. The volume should

not be turned up until it has had a couple minutes to warm up and stabilize.

The “VOLUME” switch is located in the middle of the faceplate. The remote control

reciever is located just above it. The “SOURCE” switch is on the far left and is used

to select between different input sources.

When first powered on, the display will show “15”. This corresponds to the volume

setting. Pressing “UP” on the remote or on the volume switch will increase the

volume and “DOWN” decreases it. The Maximum setting is “94” and the minimum

setting is “00”.

If “LEFT” or “RIGHT” is pressed on the remote, that channels volume setting will be

displayed for one second and then the display will return to the current volume

setting. To reset the balance, adjust the balance until there is no change in the

display setting after the one second, reduce both channels to “00”, or turn power

off.

If the source is pressing on the remote, or the source switch is pressed up, the

Input source will increment from one to four. The corresponding input on the

back will be selected. The current source will be displayed for one second, then the

new source will be displayed for one second. The display will then return to the

voume setting.

Pressing “MUTE” on the remote or down on the “SOURCE” switch will toggle

between the current volume setting and “00”.

4 GREAT VIEW AVENUE NORTH. PROVIDENCE, RI 02904 401.226.5299

The Lissa is heavy and should be placed on a sturdy support. A lot of heat is

generated and there should be several inches of ventilation room around the

unit. Excessive heat build up will decrease the life of the components inside.

The unit should be placed close to the digital source, but far away from any

noise generating components like large transformers and motors.

One the back of the unit there is an IEC power input, Fuse (3 amp Slow Blow),

Four inputs and the left and right outputs. The outputs are locat-

ed farthest from the power input. The digital inputs are individually isolated and

selectable from the front panel selector.

RIght

Output

input output

one two three four one two

Designed and manufactured in the USA

by Gill Audio Design, N. Providence RI

WARNING

SHOCK HAZARD

DO NOT OPEN

REPLACE FUSE WITH

SAME TYPE 2A, 250VAC

Model: Alana

Serial Number:__________

Left

Output

BREAK-IN PERIOD:

While the Lissa is ready to be enjoyed when shipped from the factory, it

will benefit from a few hours of break-in. Over the first 100 hours, the per-

formance will continue to improve. After this time, serious listening can begin.

It is also recommended that at least 30 minutes warm up time be given prior to

any serious listening. This allows all the internal components to fully heat up

and stabilize.

4 GREAT VIEW AVENUE NORTH. PROVIDENCE, RI 02904 401.226.5299

TWO YEAR WARRANTY:

Gill Audio Design warrants that all products have been carefully tested, inspected,

and warranted for two (2) years from the date of original purchase. This includes

parts and labor for all internal components. Vacuum tubes are covered for 90

days. Failures due to misuse, damage, neglect, or unauthorized repair or modifi-

cations are not covered. Replacing the tubes with different type tubes or replac-

ing the fuse with one of a higher rating voids all warrantees. If you have a prob-

lem with a Gill product and it is under warrantee, return it to the factory (postage

paid). Once the defect is found, you will be contacted. Gill Audio Design shall be

the sole judge of such defects. The liability of Gill Audio Design shall be limited

to the repair or replacement at its sole option of any defective product.

For Service, Upgrades, and Technical Support contact:

Gill Audio Design

4Great View Ave.

N. Providence, RI 02904

For Sales and Distribution contact:

Art Audio USA

34 Briarwood Rd.

Cranston, RI 02920

(401) 826-8286 Tel.

(401) 826 3903 Fax.

4GREAT VIEW AVENUE NORTH. PROVIDENCE, RI 02904 401.226.5299

4 GREAT VIEW AVENUE NORTH. PROVIDENCE, RI 02904 401.226.5299

SPECIFICATIONS:

Type: Solid state Integrated Amplifier

Power: 45 Watts Per Channel

Distortion: 0.05%

Output Impedance: 4 to 8 ohms

Frequency Response: 20Hz - 20kHz

full output

Input Impedance 10 kohms

S/N Ratio: 90dB.

Dimensions: 16.5" x 15" x 4.5" [ W x D x H ]

Weight:: 35 lbs. (standard version )

40 lbs. ( dual transformer version )

For Sales and Distribution contact:

Art Audio USA

34 Briarwood Rd.

Cranston, RI 02920

(401) 826-8286 Tel.

(401) 826 3903 Fax.

4GREAT VIEW AVENUE NORTH. PROVIDENCE, RI 02904 401.226.5299

Gill Audio Lissa integrated amplifier Installation guide

Brand: Gill Audio

Model: Lissa integrated amplifier

Type: Installation guide

Download PDF

report

Gill Audio Lissa integrated amplifier Installation guide

Gill Audio Lissa integrated amplifier Installation guide

Other documents