Huvema HU 20 SUPER Owner's manual

Brand: Huvema

Model: HU 20 SUPER

Category: Power tools

Type: Owner's manual

This manual is also suitable for

HU 20F SUPER

HU 20 SUPER

HU 20F SUPER

DRILLINGMACHINES

2CHANGES AND TYPING ERRORS RESERVED

CHANGES AND TYPING ERRORS RESERVED CHANGES AND TYPING ERRORS RESERVED

Table of conTenTs

1. General safety rules for all machines 3

2. Additional safety rules 4

3. Unpacking 4

3.1 Transportation instruction 4

4. Features 5

5. Installing the machine 5

6. Main parts 6

7. Control panel 7

7.1 T-grooves 7

7.2 Work table adjustment 7

7.2.1 Height adjustment 7

7.2.2 Angle adjustment 7

7.2.3 360O Turning 7

7.3 Drill depth adjustment 8

7.4 Speed Selection 8

7.5 V belt adjustment 8

7.6 Noise levels 9

8. Troubleshooting 9

9. Feed shaft spring tension 10

10. Dimensions 11

11. Control circuit diagram 11

12. Parts drawing and list 12

CHANGES AND TYPING ERRORS RESERVED

Drilling machines hU 20 sUper - hU 20f sUper

1. general safeTy rUles for all machines

N.B.: Read the instructions carefully in order to avoid any problems.

As with all machinery there are certain hazards involved with operation and use of this machine. Using the machine

with respect and caution will considerably lessen the possibility op personal injury. However, if normal safety

precautions are overlooked or ignored, personal injury to the operator may occur. Observe these rules insofar as they

are applicable to this particular machine.

This machine was designed for certain applications only. We strongly recommend that this machine NOT be modified

in any way and/or used for any application other than for which it was designed.

If you have any questions relative to its application DO NOT use the machine until you have contacted your dealer.

1. For your own safety read the instruction manual before operating the tool.

2. Keep all guards in place and in working order.

3. Ground all tools.

4. Remove adjusting keys and wrenches. Make a habit of checking the machine before turning it on.

5. Keep the work area clean. Cluttered areas and benches invite accidents.

6. Do not use in a dangerous environment, such as damp or wet locations or expose to rain. Always keep the work

area well-lit.

7. Keep children and visitors away. They must be kept at a safe distance from the machine at all times.

8. Make sure that the work area is not accessible to unauthorised persons. Use padlocks, master switches, remove

starter keys etc.

9. Never overload the machine. The capacity of the machine is at its largest when properly loaded.

10. Do not force the machine or attachment to do a job for which it was not designed.

11. Wear proper apparel. No loose clothing, gloves, neckties, rings, necklaces, bracelets or jewellery: they may get

caught in moving parts. No slip footwear is recommended. Wear a hairnet to contain long hair.

12. Always wear safety glasses and work according to safety regulations. Use a face or dust mask if operation is

dusty.

13. Always secure workpiece tightly using a vise or clamping device. This will keep both hands free to operate the

machine.

14. Do not overreach. Keep your proper footing and balance at all times.

15. Maintain tools in top condition. Keep them sharp and clean. Read the instructions carefully and follow the

instructions for cleaning, lubrication and tool replacement.

16. Lubricate the machine and fill all oil reservoirs before operation.

17. Disconnect tools before servicing and when changing accessories such as blades, bits, cutters etc.

18. Use only recommended accessories. Consult the owner’s manual for recommended accessories. The use of

improper accessories may cause hazards.

19. Avoid accidental starting. Make sure the on/off switch is in the “OFF” position before plugging in the power cord.

20. Never stand on the machine or tools. Serious injury could occur if the machine is tipped or if the cutting tool is

accidentally touched.

21. Check damaged parts. Replace or repair damaged parts immediately. Check machine for alignment of moving

parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its

operation.

22. Direction of feed. Feed work into a blade or cutter against the direction of rotation of the blade or cutter only.

23. Never leave tool running unattended. Do not turn power off until it has come to a complete stop.

24. Alcohol, medication, drugs. Never us the machine while under the influence of alcohol, medication or drugs.

25. Make sure the tool is disconnected from the power supply, before servicing, repairing etc.

26. Keep the original packing for future transport or relocation of the machine.

4CHANGES AND TYPING ERRORS RESERVED

CHANGES AND TYPING ERRORS RESERVED CHANGES AND TYPING ERRORS RESERVED

2. aDDiTional safeTy rUles

Always keep in mind that:

• the machine must be switched off and disconnected from the power supply during maintenance and repairs,

• clamped workpieces may only be measured when the machine is switched off.

Never lean over the machine, mind loose clothing, ties, jewellery etc. and wear a cap.

Do not remove safety devices or guards. Never use the machine while a guard is open.

Always use safety glasses for machining rough materials.

Burrs and chips should only be removed using a sweeper or other aid, never with your bare hands!

Never leave the machine running unattended.

3. Unpacking

Before unpacking, make sure the packaging is not damaged, broken or parts of the machine are sticking out; if any

of these defects are found, contact your retailer as soon as possible.

• Carefully open the packaging (pull it from the bottom to the top).

• Take out and read the manual; check if the machine is complete.

• Check if the machine is in good condition. There should be no damage, cracks or rust.

• Clean the surface of the machine.

3.1 TransporTaTion insTrUcTion

• Please refer to the machines specifications for proper machine handling. Be sure to use a suitable forklift or hoist

for lifting the machine.

• Handling and transportation must be carried out by qualified personnel.

• A forklift or hoist must be operated by a qualified driver.

• During transaport, always keep the machine well balanced.

• The machine must be lifted only vertically.

• Before handling, make sure all moving parts are secured and all detacheable accessories are removed from the

machine.

• Make sure the lifting straps are strong enough to hold the machine.

• Make sure the machine cannot bump or crash into anything. This will influence machine precision and may

damage the electronic control.

Always wear safety glasses!

Typical lifting strap position.

1-3. Setting the machine instruction:

1.The machine base with setting hole will be set on concrete floor.

The outlined procedures of setting the machine

MODEL

AREA

SETTED SCREW

JS-834

X=900×700

M12

JS-834V

X=900×700

M12

JS-840VB

X=900×700

M12

2.The dimension of setting hole:

Consider existing and anticipated needs, size of material to be processed through each machine, and

space for auxiliary stands, work tables or other machinery when establishing a location for your

machine. See Figure 01.

JS-834/834V/840VBDimensions(m/m)

JS-834/834V

A=1000

B=560

JS-840VB

A=1050

B=580

Lifting Straps

Figure 01

Figure 1

CHANGES AND TYPING ERRORS RESERVED

4. feaTUres

Model HU 20 Super HU 20F Super

Drilling capacity 20 mm 20 mm

Spindle taper MT2 MT2

Distance spindle column 180 mm 180 mm

Drilling depth 80 mm 80 mm

Speed range 210-2500 rpm (10) 210-2500 rpm (10)

Max. distance spindle-table 435 mm 770 mm

Column diameter 80 mm 80 mm

Table dimensions 280 x 280 mm 280 x 280 mm

Motor power 0.75 kW 0.75 kW

Weight 80 kg 92 kg

Voltage 400 V 400 V

5. insTalling The machine

Install the machine on a concrete floor. Consider existing and anticipated needs, the size of material to be processed

through each machine, and space for auxiliary stands, work tables or other machinery when establishing a location

for your machine. See figures below.

1-5Site Considerations

Working Clearances

Consider existing and anticipated needs, size of material to be processed through each machine, and

space for auxiliary stands, work tables or other machinery when establishing a location for your

machine. See Figure 01.

for the minimum working clearances of the Model JTD-16series

620mm

390mm

1-6Items Needed for Set Up

1.Column and Base

The column must be secured on the base toproperly assemble your drill press.

To secure the column to the base:

1. Place the column on the base and align themounting holes.

2. Secure the column to the base with the fourhex bolts, as shown in Figure 02

Figure 01

Figure 02

4.Slide the arbor into the spindle socket whileslowly rotating the drill chuck. The socket hasa

rectangular pocket where the tang (or flatportion of the arbor shown in Figure 21) fitsinto.

5.Seat the chuck with a rubber mallet, as shownin Figure 22.

1-8.Setting the machine instruction:

1.The machine base with setting hole will be set on concrete floor.

The outlined procedures of setting the machine

MODEL

AREA

SETTED SCREW

JTD-16 series

X=800×600

M10

2.The dimension of setting hole:

JTD-16series

Figure 21

Figure 22

Wood

Tang-SideUp

HU 20 Super: X = 770x580 mm

Use M10 set screws

HU 20F Super: X = 800x650 mm

Use M12 set screws

Figure 3

Figure 2

6CHANGES AND TYPING ERRORS RESERVED

CHANGES AND TYPING ERRORS RESERVED CHANGES AND TYPING ERRORS RESERVED

6. main parTs

4.Slide the arbor into the spindle socket whileslowly rotating the drill chuck. The socket hasa

rectangular pocket where the tang (or flatportion of the arbor shown in Figure 21) fitsinto.

5.Seat the chuck with a rubber mallet, as shownin Figure 22.

1-8.Setting the machine instruction:

1.The machine base with setting hole will be set on concrete floor.

The outlined procedures of setting the machine

MODEL

AREA

SETTED SCREW

JTD-19S

X=770×580

M10

JTD-19SF

X=800×650

M12

2.The dimension of setting hole:

JTD-19S

JTD-19SF

Figure 21

Figure 22

Wood

Tang-SideUp

HU 20 Super HU 20F Super

Head

Handle v belt tension

Table height

adjustment

Emergency stop

Motor

Drill head

Base

Table

Chuck guard

Feed handle

Pulley cover

Rack

Column

Figure 5

Figure 4

CHANGES AND TYPING ERRORS RESERVED

7. conTrol panel

• Check the power source. Push the start button to check if the motor and spindle shaft are in normal working

condition.

• Spindle speed adjustment is controlled by the speed selection switch.

• In case of an emergency, push the emergency stop.

7.1 T-grooves

• There are T grooves in the worktable and the base. They are used to fix the work piece.

7.2 Work Table aDjUsTmenT

7.2.1 Height adjustment

• Loosen the clamp handle on the left hand side.

• Turn the table handle until the table has reached its proper position.

• Tighten the clamp handle.

7.2.2 Angle adjustment

• Loosen the clamp handle on the left hand side.

• Set the table at the required angle.

• Tighten the clamp handle.

7.2.3 360O Turning

• Loosen the clamp handle on the left hand side.

• Turn the table to the desired position.

• Tighten the clamp handle.

3-1.Control panel instruction:

A. Jkm Cam Switch (high/low)

B.Start Button(For CE)

C.Emergency Stop Button (For CE)

1. Check the power source

Push the start button to judge the motor and

spindle shaft is in normal condition or not.

2. If it needs to stop urgently, just push the

emergency stop switch.

3-1.Control panel instruction:

A. Jkm Cam Switch (high/low)

B.Start Button(For CE)

C.Emergency Stop Button (For CE)

1. Check the power source

Push the start button to judge the motor and

spindle shaft is in normal condition or not.

2. If it needs to stop urgently, just push the

emergency stop switch.

A: Speed selection switch

B: Start button

C: Emergency stop

Figure 6

3-2.Operation illustration and procedure:

1. There are three T grooves in the worktable. It is used to fix the work piece.

1-1.There are two T grooves in the base, too. It is convenient for fixing the longer, heavier and larger

working piece.

OPTION

2. The pulley cover is strictly prohibited to open in normal operation condition.

3. Protect safety guard shall be allocated in a proper position in operation. It is controlled by a micro

witch. (For CE)

4. Adjustment of feeding limit

To prevent unwanted penetration to work piece, the feeding limit

shall be set by adjusting the appropriate position of feeding depth

fixing button as long as the distance between the end of tool and

top surface if work piece is measured.

A. Setting of feeding depth

1. Loosen knob A.

2. Turn scaled ring B to desired feeding depth.

3. Lock knob A.

Lock

Loose

Figure 7

8CHANGES AND TYPING ERRORS RESERVED

CHANGES AND TYPING ERRORS RESERVED CHANGES AND TYPING ERRORS RESERVED

7.3 Drill DepTh aDjUsTmenT

To prevent the drill from going too deep into the work piece, you can set the

feeding limit by adjusting the position of the feed depth knob

(A, figure 8).

• Loosen knob A

• Turn scaled ring B to the desired feeding depth

• Lock knob A

7.4 speeD selecTion

Drill

diameter

(mm)

Material

Cast Iron Steel Iron Aluminium Alloy Copper

Drilling Drilling Drilling Drilling Drilling

2 4780 1275 3980 7960 4460

3 3185 850 2650 5310 2970

4 2390 640 1990 3980 2230

5 1910 510 1590 3185 1785

6 1590 425 1330 2655 1485

7 1365 365 1140 2275 1275

8 1195 320 995 1990 1115

9 1060 285 885 1770 990

10 955 255 800 1590 890

11 870 230 725 1450 910

12 795 210 665 1330 745

13 735 195 610 1225 685

14 680 180 570 1135 635

15 640 170 530 1060 600

16 600 160 500 995 560

17 560 150 470 935 525

18 530 140 440 885 495

19 500 135 420 835 470

20 480 130 400 795 445

25 380 100 320 640 355

30 320 85 265 530 300

40 240 65 200 400 225

7.5 v belT aDjUsTmenT

• Loosen knob B on both sides of the headstock.

• Push handle A forward to increase the belt tension, back to decrease the tension.

• Lock knob B firmly again.

3-2.Operation illustration and procedure:

1. There are three T grooves in the worktable. It is used to fix the work piece.

1-1.There are two T grooves in the base, too. It is convenient for fixing the longer, heavier and larger

working piece.

OPTION

2. The pulley cover is strictly prohibited to open in normal operation condition.

3. Protect safety guard shall be allocated in a proper position in operation. It is controlled by a micro

witch. (For CE)

4. Adjustment of feeding limit

To prevent unwanted penetration to work piece, the feeding limit

shall be set by adjusting the appropriate position of feeding depth

fixing button as long as the distance between the end of tool and

top surface if work piece is measured.

A. Setting of feeding depth

1. Loosen knob A.

2. Turn scaled ring B to desired feeding depth.

3. Lock knob A.

Lock

Loose

JTD-16series

1. Loosen knob B on both sides of headstock.

2. Push handle A forward as arrow sign to get belt tension.

3.Lock knob B firmly to fix belt tension.

When speed change is required. Loosen lead bolt (parts no. 22-S2) on both side of headstock. Pull belt

handle (parts no. 26) to allow belts repositioning and then move belts to correct groove to acquire

desired speed. See following speed chart for reference.

JTD-16S

JTD-16SA

For proper belt tension, use 10 1bs pressure or hand pressure on the belt as shown as bellow.

Models belt model tables

Machine model

Belt specifications

Quantity

JTD-16S

A-42

JTD-16SA

A-25 / A-26

Figure 8

Figure 9

CHANGES AND TYPING ERRORS RESERVED

When you want to change the speed range, loosen the knobs on both sides of the headstock and open the cover.

Pull the belt handle to allow belt repositioning and then move belt to the required groove.

For proper belt tension, you should be able to push the belt in to a distance of about 13 mm.

Machine model Belt specifications Quantity

HU 20 Super FM-42.5 1

HU 20F Super FM-42.5 1

7.6 noise levels

Noise level with no load: Lpa = 62 dB(A)

Noise level with load: Lpa = 64 dB(A)

8. TroUbleshooTing

Switch off power and remove plug from power source outlet before trouble shooting.

Problem Solution

Drill is caught in the work piece and the spindle

has stopped

1. Push the emergency button

2. Turn off the power

3. Turn the spindle manually counterclockwise to withdraw

the tool from the work piece

4. Clean any chips on the work piece.

5. Turn on the power again

6. Resume drilling slowly to test if the drill does not get caught

again and then return to normal feed

Supply of cutting liquid inadequate 1. Check if the pump is running

2. Check if the hose is leaking

Spindle shaft cannot run completely 1. Check the belt tension

2. If the tension is too little, adjust it

3. Replace worn belts

Motor does not work 1. Check the power and check if the machine is switched on

2. Check the power cable for damage. Replace damaged

cables directly.

Spindle shaft makes a lot of noise 1. Check the bearing

2. Check if the v belt tension is too high; this will cause noise.

Drill oscillation 1. Check chuck condition

2. Make sure the drill is properly fixed in the chuck

JTD-19 series

1. Loosen knob B on both sides of headstock.

2. Push handle A forward as arrow sign to get belt tension.

3.Lock knob B firmly to fix belt tension.

When speed change is required. Loosen lead bolt (parts no. 22-S2) on both side of headstock. Pull belt

handle (parts no. 26) to allow belts repositioning and then move belts to correct groove to acquire

desired speed. See following speed chart for reference.

JTD-19series

For proper belt tension, use 10 1bs pressure or hand pressure on the belt as shown as bellow.

Models belt model tables

Machine model

Belt specifications

Quantity

JTD-19series

FM-42.5

JTD-16series

1. Loosen knob B on both sides of headstock.

2. Push handle A forward as arrow sign to get belt tension.

3.Lock knob B firmly to fix belt tension.

When speed change is required. Loosen lead bolt (parts no. 22-S2) on both side of headstock. Pull belt

handle (parts no. 26) to allow belts repositioning and then move belts to correct groove to acquire

desired speed. See following speed chart for reference.

JTD-16S

JTD-16SA

For proper belt tension, use 10 1bs pressure or hand pressure on the belt as shown as bellow.

Models belt model tables

Machine model

Belt specifications

Quantity

JTD-16S

A-42

JTD-16SA

A-25 / A-26

Figure 10

Figure 11

10 CHANGES AND TYPING ERRORS RESERVED

CHANGES AND TYPING ERRORS RESERVED CHANGES AND TYPING ERRORS RESERVED

9. feeD shafT spring Tension

The feed shaft return spring is set at the factory; however, during the life of the drill press you may want to adjust the

spring so that the feed shaft return pressure suits your operating needs.

Turn the machine off and disconnect it from the mains before maintenance or repairs are performed!

• Take out the screw and take away the cover (figure 12).

• Wipe off any oil on the spring lock cover so it does not slip when you hold the cover. Wear protective gloves.

• Loosen the lock nut (figure 13 and 14) and pull the cover a little bit toward you (see figure 14), so that it comes free

of the spring cover lock slot (figure 15). Note: It is important to keep a good grip during this step. Letting go of the

cover will cause the spring to rapidly uncoil.

• Rotate the cover counterclockwise to increase spring tension, or let the cover slowly unwind in a clockwise

direction to reduce spring tension.

• Engage the next available spring cover lock slot and push the spring lock cover back.

• Retighten the lock nut and replace the cover.

10. Dimensions

All dimensions in mm.

5-1. Feed Shaft Spring Tension:

The feed shaft return spring is adjusted at thefactory; however, during the life of the drill pressyou may

want to adjust the feed shaft returnspring so the feed shaft return pressure suits youroperating needs.

To adjust the feed shaft spring tension:

1. UNPLUG THE DRIL PRESS !

2. Wipe off any oil on the spring lock cover so itdoes not slip in your fingers when you hold the

cover from spinning (see Figure 28).

3. While holding the spring lock cover against the side of the head stock so the cover stayssplined with

the locking lug; loosen the jam nut and loosen the cover nut approximately1⁄4" (see Figure 30).

4. Put on heavy leather gloves to protect your hands from possible lacerations if the springuncoils

during the next step.

5. Pull the cover outward just enough to disengage the spring-cover lock slot from thelocking lug. Note:

It is important to keep a good grip during this step. Letting go of thecover will cause the spring to

rapidly uncoil.

6. Rotate the cover counterclockwise to increase spring tension, or let the cover slowly unwind in the

clockwise direction to reduce spring tension.

7. Engage the next available spring-cover lock slot with the locking lug and hold the springlock cover

tightly against the side of the headstock.

8. Snug the cover nut against the spring cover just until the nut stops, and then back offthe nut

approximately 1⁄3 turn, or just enough so there is no binding at complete spindletravel.

9. Hold the cover nut and tighten the jam nut against the cover nut.

Figure 27

Figure 29

Figure 30

Figure 28

Lock Nut

Spring Lock

Cover

Spring Cover

Lock Slot

Screw

Wrench

Size 19mm

Figure 13

Figure 14 Figure 15

Figure 12

6.Specification;

Model

Item

JTD-19S

JTD-19SF

Drilling capacity

19mm

Tapping capacity

----------

Spindle taper

M.T.#2

Spindle travel

80mm

Spindle speed (rpm)

50 Hz

210– 2500/min

Number of speeds

10 steps

Motor

0.37kW 400V 3Ph or 0.75kW 400V 3PH

Net weight (kgs)

N.W-80Kg

N.W-92Kg

Dimensions(m/m)

JTD-19S

JTD-19SF

A 1050 1730

B 410

C=470 × c1=280

C=500 × c1=330

D D=280 × d1=280

E 420 800

F 650 1280

G 620

H 180

I 80

T 12

HU 20 Super HU 20F Super

Figure 16

CHANGES AND TYPING ERRORS RESERVED

11. conTrol circUiT Diagram

Symbol Function Tech. dat Remark

M Motor AC400V / 3PH

KA Relay AC400V 7.5A LY-3

SQ1 Limit switch 400V / 5A

SQ2 Micro switch chuck guard 400V/ 5A

SB1 Pushbutton INOAC400V / 2.1.A BF-22-G-1-1A

SB2 Emergency stop INCAC400V / 2.1 A BF-22-R-0-1B

SA ON/OFF switch 400V 6A VDE-0660

C Capacitator 1200V 503K

R Resistor 1/4W 1Ω

7.Control circuit diagram and component part list;

Part No.

Component/Object

Manufacturer

PCS

Motor

AC400V / 3PH /

RELAY

AC 400V7.5A

LY-3

SQ1

LIMIT SWITCH

400V/5A

SQ2

MICRO SWITCH

CHUCK GUARD

400V/5A

SB1

PUSH BUTTON

INOAC400V/2.1A

BF-22-G-1-1A

SB2

PUSH BUTTON

EMERGENCY STOP

INCAC400V /2.1A

BF-22-R-0-1B

CONTROL SWITCH

400V6A

VDE-0660

CAPACITY

1200V

503K

RESISTOR

1/4W

1Ω

Figure 17

12 CHANGES AND TYPING ERRORS RESERVED

CHANGES AND TYPING ERRORS RESERVED CHANGES AND TYPING ERRORS RESERVED

12. parTs DraWing anD lisT

8.Drawing and parts list;

JTD-19S

JTD-19SF

HU 20F Super

Figure 18

CHANGES AND TYPING ERRORS RESERVED

JTD-19 series

BASE

COLUMN HOLDER

2-S1

BOLT

2-S2

SPRING WASHER

COLUMN

TABLE BRACKET

OIL CUP

5-S1

GEAR

SHAFT

WORM

TABLE HANDLE

HANDLE BOLT

9-S1

SET SCREW

TABLE ARM BRACKET

11-S1

BOLT

11-S2

SPRING WASHER

ANGLE SCALE

SCALE

CLAMP HANDLE

16-S1

16-S2

CLAMP BOLT

TABLE BOLT

TABLESWIVEL TYPE

RACK

RACK RING

20A

COLUMN RING

20B

BALL

20-S1

SET SCREW

HEAD BODY

22A

FEED SHIFT COVER

22-S1

SCREW

22-S2

LEAD BOLT

22-S3

22-S4

SET SCREW

22-S5

NUT

22-S6

SET SCREW

22-S7

LEAD BOLT

SHIFTER BAR

SHIFTER

27-S1

SET SCREW

29L

SLIDE BAR (L)

29S

SLIDE BAR (S)

29-S1

WASHER

MOTOR BASE

31-S1

SPRING WASHER

31-S2

NUT

HANDLE BODY

FEED SHAFT

SCALE GUIDER

STOP KNOB

FEED HANDLE

GRIP

SCALE RING

SCALE

RIVET

SPRING CAP

NUT

QUILL

RUBBER WASHER

SPINDLE

BALL BEARING

THRUST BEARING

BALL BEARING

SPINDLE NUT

SPINDLE SLEEVE

BALL BEARING

COLLAR

SNAP RING

PULLEY NUT

SPINDLE PULLEY

TAPER ARBOR

DRILL CHUCK

DRILL SHIFTER

MOTOR

68-S1

BOLT

68-S2

WASHER

68-S3

NUT

MOTOR WIRE

MOTOR PULLEY

73-S1

SCREW

WIRE

76A

WIRE PLUG

JKM CAM SWITCH

78A

ON SWITCH

SWITCH COVER

79-S1

SCREW

PULLEY COVER

81-S1

SCREW

81-S2

WASHER

PULLEY COVERKNOB

85-S1

PULLEY COVER SCREW

V-BELT

ALLEN WRENCHL

ALLEN WRENCHS

MICRO SWITCH

MICRO SWITCHBOX

93A

SPRING SHEET

93-S1

SCREW

93-S2

NUT

CLUTCH

94-S1

NUT

94-S2

SPRING WASHER

94-S3

SCREW

101

MICRO SWITCH BRACKET

101A

MICRO SWITCH

101B

MICROSWITCH BOARD COVER

101C

MICRO SWITCH WIRE

101-S1

SCREW

101-S2

SCREW

101-S3

LEAD BOLT

102

SAFETY GUARD

102A

SAFETY GUARD SLIDE

102-S1

SCREW

102-S2

LEAD BOLT

103

BRACKET ROD

103A

SUPPORT ARM

103B

LOWER BRACKET ROD

103-S1

HEX NUT

103-S2

SPRING WASHER

103-S3

C-RING

104

EMERGENCY STOP SWTCH

104A

SWITCH COVER

104B

RUBBER SHEET

104-S1

SCREW

105

PC BOARD COVER

105A

ALUMINIUM COVER

105B

RUBBER SHEET

105C

RUBBER SHEET

105D

BAKELITE SHEET

105-S1

SCREW

105-S2

SCREW

105-S3

NUT

105-S4

NUT

108

CONTACTOR

108-S1

SCREW

801

MACHINE ID LABEL

14 CHANGES AND TYPING ERRORS RESERVED

CHANGES AND TYPING ERRORS RESERVED CHANGES AND TYPING ERRORS RESERVED

Our products are frequently updated and improved. Minor changes may not yet be incorporated in this manual.

Always state the year of build, type and serial number of the machine in correspondence.

Manufacturer and importer assume no responsibility for defects which result from not reading the manual carefully

or wrong use of the machine. No rights can be derived from this manual.

other means without written permission from the publisher.

CHANGES AND TYPING ERRORS RESERVED

CE DECLARATION OF CONFORMITY

(in accordance with supplement II, section 1A of the Machinery Directive)

Industrie & Handelsonderneming Huberts bv, Kennedylaan 14, 5466 AA Veghel, the Netherlands,

in the capacity of importer, is to be held responsible for declaring that the Huvema machines:

Drilling machines HU 20 Super - hU 20f Super

which this declaration relates to, are conform the following norms:

NEN-EN-ISO 12100:2010, NEN-EN-IEC 60204-1:2006/C11:2010, NEN-EN-IEC 61000-6-1:2007,

NEN-EN-IEC 61000-6-3:2007/A1:2011/C11:2012, NEN-EN 12717:2001+A1:2009

and meet the basic requirement of the:

• Machinery Directive: 2006/42/EC

• Low Voltage Directive: 2006/95/EC

• EMC Directive: 2004/108/EC

Veghel, the Netherlands, June 2014

L. Verberkt

Managing director

2014 V1

Huvema HU 20 SUPER Owner's manual

Brand: Huvema

Model: HU 20 SUPER

Category: Power tools

Type: Owner's manual

This manual is also suitable for

HU 20F SUPER

Download PDF

report

Huvema HU 20 SUPER Owner's manual

This manual is also suitable for

Huvema HU 20 SUPER Owner's manual

Related papers

Other documents