purchasing this Thank you
INSTRUCTION MANUAL
DESKTOP MICROPHONE
for MC-6OA desktop microphone.
This rrricrophone
performance when used
amateur communications system. It provides excellent
has been designed expressly for use with
your with any
KENWOOD
complete with and is The zinc die-cast base offers
thereby upgrading your transceiver,
existing system.
improved stability
a feather-touch
PTT
and a built-in selector switch, switch, an impedance
preamplifier.
serious damage. microphone as parts. Do not The microphone is constructed of precision
open the it may result in
The and vibration. microphone is sensitive to shock Treat
it with care.
50W500
IMP. Switch rON/OFF Switch
WIIC AMP INIOUT
(Underside)
UP/DOWN
LOCK Switch
Switch
Connect to
Radio Mic
Terminal
-
PTT Switch
KENWOOD
KENWOOD CORPORAl'ION
0
B62-1643-00
(M)
090807060504030201 00
Installing the Batteries
1
Remove the
4
screws from the base of the
rrricrophone and gently base from the separate the
rr~icrophone
install the not need to connector, you through its microphone transceiver supplies
Replace the
marked in polarities with
batteries into the battery compartment, Insert two unit.
2 AA
being sure to match the those
the compartment.
3
4
screws.
Note:
If
your power
do two
AA
batteries.
111
Batteries
"AA" hlkaline
(Not Ni-Cd)
Il
the non-coiled cable
on the Slide the microphone
Connecting to the Transceiver
1 into the bracket base
stand.
2 Connect ,from
retractable cable
the microphone. to the of the base the rear
stand rear of
3
Connect the from the base to the
transceiver's microphone jack.
First reniove microphone, then slide the base of the .the
switch to tlie turn the
IN
position to preamplifier ON.
Transmitting
transmit, press and hold the
bypassed and
With the switch in the
OUT
position, the preamplifier is
the batteries are disconnected. To conserve
To
PlT
into the microphone.
turn the preamplifier
switch, then speak
battery power,
OFF
when it is not in
use.
The
MC-6OA
switch which allows equipped with a is
LOCK
lock the With the switch in the
IN
position, the preamplifier is
ON
and
you to PlT
pressing it. While pressing operated equipment.
be used with
switch down without continuously the microphone can
VOX
the PlT switch, press the
LOCK
switchtokeepthePlTswitclilocked.ToreleasetheL0CK
.
Oneral:ionWi3thouttheBaseStand
switch, sim~lv Dress it aaain.
I
.
.r.
-
the base microphone without can use the You stand by
When
you
have
finished release
the
PIT
switch
connecting the microphone to the retractable cable, then
the microphone impedance
Impedance Selection
you can the transceiver. Doing so means
to receive. directly to no
You can set to
500
i2
or
50
ki2. Slide the
50W500
switch on
IMP.
the top of the
microphone
this microphone with any can use
your desired position. to
Microphone Preamplifier
You
KENWOOD
SSB mobile transceivers.
transceiver. It has been designed especially for FM and
You can control the preamplifier
using the
MIC AMP INIOUT
longer use
the transceiver. switch on the inside of the
base of
the preamplifier, which is built info
transceiver, you to the With a direct connection
the base
stand. must use
the
ONIOFF
to the OFF transmit, and position to to the ON when you transmit. Slide the switch the microphone switch located on the top of
position to receive.
UPIDOWN Switcli
Use the
UPIDOWN
further details on how to select
your transceiver instruction
switch to select the transceiver's
operating frequency. Refer to
manual for an operating
frequency.
Type:
Cornmunical:ion dynamic microphone type with PlT
Frequency response:
circuit.
Element:
Impedance:
Sensitivity:
Microphone
Preamp out
Preamp in
Microphone or preamp off
Preamp on
Recorr~mended
type, unidirectional
from microphone:
operating distance
Moving coil
Dual impedance
(1 000
Hz)
50
ki2
f30%, 500
i2
f
switch selectable
30%
slide
(0
dB
=
1
V/
pBAR,
1000
Hz)
150
HZ
-
10
kHz
inches) minimum
(-6
dB)
200
Hz
-
7
kHz
(-6
dB)
10
cm
(4
MIC
unit
connection
Impedance
50k-500
p
(White)
1
(Green)
P.
T. T
MIC
stand
connection
MIC
AMP
IN -OUT
cable connection MIC
PG-4C
(Black)
(Shield)
A
(Yellow)
-
1
-
2
