Hotpoint Ariston PC 640 (BK)/HA User guide

English

Operating Instructions

HOB

Français

Mode d’emploi

TABLE DE CUISSON

Español

Manual de instrucciones

ENCIMERA

Portuges

Instruções para a utilização

PLANO

Italiano

Istruzioni per l’uso

PIANO

Sommario

Istruzioni per l’uso,1

Avvertenze,3

Assistenza,8

Descrizione dell’apparecchio,10

Installazione,13

Avvio e utilizzo,17

Precauzioni e consigli,17

Manutenzione e cura,18

Anomalie e rimedi,18

Contents

Operating Instructions,1

Warnings,3

Assistance,8

Description of the appliance,10

Installation,19

Start-up and use,23

Precautions and tips,23

Maintenance and care,24

Troubleshooting,24

Sommaire

Mode d’emploi,1

Avertissements,4

Assistance,8

Description de l’appareil,10

Installation,25

Mise en marche et utilisation,29

Précautions et conseils,29

Nettoyage et entretien,30

Anomalies et remèdes,30

Sumario

Manual de instrucciones,1

Advertencias,4

Asistencia,8

Descripción del aparato,10

Instalación,31

Puesta en funcionamiento y uso,35

Precauciones y consejos,35

Mantenimiento y cuidados,36

Anomalías y soluciones,36

Índice

Instruções para a utilização,1

Advertências,5

Assistência,9

Descrição do aparelho,11

Instalação,37

Início e utilização,41

Precauções e conselhos,41

Manutenção e cuidados,42

Anomalias e soluções,42

PC 640 (BK)/HA

Page is loading ...

3

Avvertenze

ATTENZIONE: Questo apparecchio e le sue parti

accessibili diventano molto caldi durante l’uso.

Bisogna fare attenzione ed evitare di toccare gli

elementi riscaldanti. Tenere lontani i bambini inferiori

agli 8 anni se non continuamente sorvegliati. Il

presente apparecchio può essere utilizzato dai

bambini a partire dagli 8 anni e da persone con

ridotte capacità siche, sensoriali o mentali oppure

con mancanza di esperienza e di conoscenza se

si trovano sotto adeguata sorveglianza oppure se

sono stati istruiti circa l’uso dell’apparecchio in modo

sicuro e se si rendono conto dei pericoli correlati. I

bambini non devono giocare con l’apparecchio. Le

operazioni di pulizia e di manutenzione non devono

essere effettuate dai bambini senza sorveglianza.

ATTENZIONE: Lasciare un fornello incustodito con

grassi e olii può essere pericoloso e può provocare un

incendio. Non bisogna MAI tentare di spegnere una

amma/incendio con acqua, bensì bisogna spegnere

l’apparecchio e coprire la amma per esempio con

un coperchio o con una coperta ignifuga.

ATTENZIONE: Rischio di incendio: non lasciare

oggetti sulle superci di cottura.

Non utilizzare mai pulitori a vapore o ad alta pressione

per la pulizia dell’apparecchio.

Eliminare eventuali liquidi presenti sul coperchio

prima di aprirlo. Non chiudere il coperchio in vetro

(se presente) con i bruciatori gas o la piastra elettrica

ancora caldi.

L’apparecchio non è destinato a essere messo in

funzione per mezzo di un temporizzatore esterno

oppure di un sistema di comando a distanza

separato.

ATTENZIONE: l’uso di protezioni del piano

inappropriate può causare incidenti.

Warnings

WARNING: The appliance and its accessible parts

become hot during use. Care should be taken to

avoid touching heating elements. Children less than 8

years of age shall be kept away unless continuously

supervised. This appliance can be used by children

aged from 8 years and above and persons with

reduced physical, sensory or mental capabilities or

lack of experience and knowledge if they have been

given supervision or instruction concerning use of the

appliance in a safe way and understand the hazards

involved. Children shall not play with the appliance.

Cleaning and user maintenance shall not be made

by children without supervision.

WARNING: Unattended cooking on a hob with fat or

oil can be dangerous and may result in re. NEVER

try to extinguish a re with water, but switch off the

appliance and then cover ame e.g. with a lid or a

re blanket.

WARNING: Danger of re: do not store items on the

cooking surfaces.

Never use steam cleaners or pressure cleaners on

the appliance.

Remove any liquid from the lid before opening it. Do

not close the glass cover (if present) when the gas

burners or electric hotplates are still hot.

The appliance is not intended to be operated by

means of an external timer or separate remote

control system.

CAUTION: the use of inappropriate hob guards can

cause accidents.

Page is loading ...

10

Descrizione dell’apparecchio

Vista d’insieme

1. Griglie di appoggio per RECIPIENTI DI COTTURA

2. BRUCIATORI GAS

3. Manopole di comando dei BRUCIATORI GAS

4. Candela di accensione dei BRUCIATORI GAS

5. DISPOSITIVO DI SICUREZZA

• BRUCIATORI GAS sono di diverse dimensioni e potenze. Scegliete quello

più adatto al diametro del recipiente da utilizzare.

• Manopole di comando dei BRUCIATORI GAS per la regolazione della

amma.

• Candela di accensione dei BRUCIATORI GAS permette l’accensione

automatica del bruciatore prescelto.

• DISPOSITIVO DI SICUREZZA in caso di spegnimento accidentale della

amma, interrompe l’uscita del gas.

Description of the appliance

Overall view

1. Support Grid for COOKWARE

2. GAS BURNERS

3. Control Knobs for GAS BURNERS

4. Ignition for GAS BURNERS

5. SAFETY DEVICES

• GAS BURNERS differ in size and power. Use the diameter of the cookware

to choose the most appropriate burner to cook with.

• Control Knobs for GAS BURNERS adjust the size of the ame.

• GAS BURNER IGNITION enables a specic burner to be lit automatically.

• SAFETY DEVICE stops the gas flow if the flame is accidentally

extinguished.

Description de l’appareil

Vue d’ensemble

1. Grilles support de CASSEROLES

2. BRÛLEURS À GAZ

3. Manettes de commande des BRÛLEURS GAZ

4. Bougie d’allumage des BRÛLEURS GAZ

5. DISPOSITIF DE SÉCURITÉ

• BRÛLEURS GAZ ils ont plusieurs dimensions et puissances. Choisissez

celui qui correspond le mieux au diamètre de votre casserole.

• Manettes de commande des BRÛLEURS GAZ pour le réglage de la

amme.

• La bougie d’allumage des BRÛLEURS GAZ permet l’allumage

automatique du brûleur sélectionné.

• DISPOSITIF DE SÉCURITÉ en cas d’extinction accidentelle de la amme,

coupez immédiatement l’arrivée du gaz.

Descripción del aparato

Vista en conjunto

1. Parrillas de apoyo para RECIPIENTES DE COCCIÓN

2. QUEMADORES A GAS

3. Mandos de los QUEMADORES A GAS

4. Bujía de encendido de los QUEMADORES A GAS

5. DISPOSITIVO DE SEGURIDAD

• QUEMADORES A GAS: son de distintas dimensiones y potencias. Elija

siempre el más adecuado para el diámetro del recipiente que va a utilizar.

• Mandos de los QUEMADORES A GAS para la regulación de la llama.

• Bujía de encendido de los QUEMADORES A GAS: permite el encendido

automático del quemador.

• DISPOSITIVO DE SEGURIDAD: si se apaga accidentalmente la llama,

interrumpe la salida de gas.

1

3

5

4

2

Page is loading ...

GB

19

Installation

! Before operating your new appliance please read this instruction booklet

carefully. It contains important information for safe use, installation and care

of the appliance.

! Please keep these operating instructions for future reference. Pass them on

to possible new owners of the appliance.

Positioning

! Keep packaging material out of the reach of children. It can become a choking

or suffocation hazard (see Precautions and tips).

! The appliance must be installed by a qualied professional according to the

instructions provided. Incorrect installation may cause harm to people and

animals or may damage property.

! This unit may be installed and used only in permanently ventilated rooms

in accordance with current national regulations. The following requirements

must be observed:

• The room must be equipped with an air extraction system that expels

any combustion fumes. This may consist of a hood or an electric fan that

automatically starts each time the appliance is switched on.

In a chimney stack or branched flue.

(exclusively for cooking appliances)

Directly to

the Outside

• The room must also allow proper air circulation, as air is needed for

combustion to occur normally. The ow of air must not be less than 2 m

3

/h

per kW of installed power.

The air circulation system may take air directly

from the outside by means of a pipe with an

inner cross section of at least 100 cm

2

; the

opening must not be vulnerable to any type

of blockages.

The system can also provide the air needed for

combustion indirectly, i.e. from adjacent rooms

tted with air circulation tubes as described

above. However, these rooms must not be

communal rooms, bedrooms or rooms that

may present a re hazard.

• Intensive and prolonged use of the appliance may necessitate

supplemental ventilation, e.g. opening a window or increasing the power

of the air intake system (if present).

• Liquid petroleum gas sinks to the oor as it is heavier than air. Therefore,

rooms containing LPG cylinders must also be equipped with vents to allow

gas to escape in the event of a leak. As a result LPG cylinders, whether

partially or completely full, must not be installed or stored in rooms or

storage areas that are below ground level (cellars, etc.). It is advisable to

keep only the cylinder being used in the room, positioned so that it is not

subject to heat produced by external sources (ovens, replaces, stoves,

etc. ) which could raise the temperature of the cylinder above 50°C.

A

Examples of

ventilation holes

for comburant air.

Enlarging the ventilation slot

between window and floor.

Adjacent

Room

Room to be

Vented

Fitting the appliance

The following precautions must be taken when installing the hob:

• Kitchen cabinets adjacent to the appliance and taller than the top of the

hob must be at least 200 mm from the edge of the hob.

• Hoods must be installed according to their relative installation instruction

manuals and at a minimum distance of 650 mm from the hob (see gure).

• Place the wall cabinets adjacent to the hood at a minimum height of 420

mm from the hob (see gure).

If the hob is installed beneath a wall cabinet,

the latter must be situated at a minimum of 700

mm above the hob.

• The installation cavity should have the dimensions indicated in the gure.

Fastening hooks are provided, allowing you to fasten the hob to tops that

are between 20 and 40 mm thick. To ensure the hob is securely fastened

to the top, we recommend you use all the hooks provided.

555 mm

55 mm

475 mm

Before the installation remove the grids and burners from the hob and turn it

upside down, making sure you don’t damage the thermocouples and spark

plugs.

Apply the seals that come with the

appliance along the outer edges of

the hob to prevent any passage of air,

humidity and water (see Figure).

For proper application make sure the

surfaces to be sealed are clean, dry and

free of any grease/oil.

Hook fastening diagram

Hooking position for top H=20mm Hooking position for top H=30mm

Front

Hooking position for top H=40mm Back

! Use the hooks contained in the “accessory pack”.

600mm min.

420mm min.

650mm min.

20

GB

• Where the hob is not installed over a built-in oven, a wooden panel must

be installed as insulation. This must be placed at a minimum distance of

20 mm from the lower part of the hob.

Ventilation

To ensure adequate ventilation, the back panel of the cabinet must be

removed. It is advisable to install the oven so that it rests on two strips of

wood, or on a completely at surface with an opening of at least 45 x 560

mm (see diagrams).

560 mm.

45 mm.

Where a hob is installed above an oven without a forced ventilation cooling

system, adequate ventilation must be provided inside the cabinet by means

of air holes through which air can pass (see gure).

Electrical connection

Hobs equipped with a three-pole power supply cable are designed to operate

with alternating current at the voltage and frequency indicated on the data

plate (this is located on the lower part of the appliance). The earth wire in the

cable has a green and yellow cover. If the appliance is to be installed above

a built-in electric oven, the electrical connection of the hob and the oven must

be carried out separately, both for electrical safety purposes and to make

extracting the oven easier.

Connecting the supply cable to the mains

Install a standardised plug corresponding to the load indicated on the data

plate.

The appliance must be directly connected to the mains using an omnipolar

circuit-breaker with a minimum contact opening of 3 mm installed between

the appliance and the mains.

The circuit-breaker must be suitable for the charge indicated and must comply

with current electrical regulations (the earthing wire must not be interrupted

by the circuit-breaker). The supply cable must not come into contact with

surfaces with temperatures higher than 50°C.

! The installer must ensure that the correct electrical connection has been

made and that it is compliant with safety regulations.

Before connecting to the power supply, make sure that:

• the appliance is earthed and the plug is compliant with the law.

• the socket can withstand the maximum power of the appliance, which is

indicated on the data plate.

• the voltage is in the range between the values indicated on the data plate.

• the socket is compatible with the plug of the appliance. If the socket is

incompatible with the plug, ask an authorised technician to replace it. Do

not use extension cords or multiple sockets.

! Once the appliance has been installed, the power supply cable and the

electrical socket must be easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by authorised technicians

only (see Assistance).

! The manufacturer declines any liability should these safety measures not

be observed.

Gas connection

The appliance should be connected to the main gas supply or to a gas

cylinder in compliance with current national regulations. Before carrying out

the connection, make sure the cooker is compatible with the gas supply you

wish to use. If this is not the case, follow the instructions indicated in the

paragraph “Adapting to different types of gas.”

When using liquid gas from a cylinder, install a pressure regulator which

complies with current national regulations.

! Check that the pressure of the gas supply is consistent with the values

indicated in Table 1 (“Burner and nozzle specications”). This will ensure the

safe operation and longevity of your appliance while maintaining efcient

energy consumption.

Connection with a rigid pipe (copper or steel)

! Connection to the gas system must be carried out in such a way as not to

place any strain of any kind on the appliance.

There is an adjustable L-shaped pipe tting on the appliance supply ramp

and this is tted with a seal in order to prevent leaks. The seal must always

be replaced after rotating the pipe tting (seal provided with appliance). The

gas supply pipe tting is a threaded 1/2 gas cylindrical male attachment.

Connecting a flexible jointless stainless steel pipe to a threaded

attachment

The gas supply pipe tting is a threaded 1/2 gas cylindrical male attachment.

These pipes must be installed so that they are never longer than 2000 mm

when fully extended. Once connection has been carried out, make sure that

the exible metal pipe does not touch any moving parts and is not compressed.

! Only use pipes and seals that comply with current national regulations.

Checking the tightness of the connection

! When the installation process is complete, check the pipe ttings for leaks

using a soapy solution. Never use a ame.

Adapting to different types of gas

To adapt the hob to a different type of gas other than default type (indicated

on the rating plate at the base of the hob or on the packaging), the burner

nozzles should be replaced as follows:

1. Remove the hob grids and slide the burners off their seats.

2. Unscrew the nozzles using a 7 mm socket spanner, and replace them

with nozzles for the new type of gas (see table 1 “Burner and nozzle

characteristics”).

3. Reassemble the parts following the above procedure in the reverse order.

4. Once this procedure is nished, replace the old rating sticker with one

indicating the new type of gas used. Sticker are available from any of our

Service Centres.

• Adjusting the burners’ primary air

Does not require adjusting.

GB

21

• Setting the burners to minimum

1. Turn the tap to the low ame position.

2. Remove the knob and adjust the adjustment

screw, which is positioned in or next to the tap

pin, until the ame is small but steady.

3. Having adjusted the ame to the required low setting, while the burner is

alight, quickly change the position of the knob from minimum to maximum

and vice versa several times, checking that the ame does not go out.

4. Some appliances have a safety device (thermocouple) tted. If the device

fails to work when the burners are set to the low ame setting, increase

this low ame setting using the adjusting screw.

5. Once the adjustment has been made, replace the seals on the by-passes

using sealing wax or a similar substance.

! If the appliance is connected to liquid gas, the regulation screw must be

fastened as tightly as possible.

! Once this procedure is nished, replace the old rating sticker with one

indicating the new type of gas used. Stickers are available from any of our

Service Centres.

! Should the gas pressure used be different (or vary slightly) from the

recommended pressure, a suitable pressure regulator must be tted to the

inlet pipe (in order to comply with current national regulations).

Electrical

connections

DATA PLATE

EU Regulation no. 66/2014 implementing

Directive 2009/125/EC.

standard EN 30-2-1

ECODESIGN

see data plate

This appliance conforms to the following

European Economic Community directives:

- 2006/95/EC dated 12/12/06 (Low Voltage)

and subsequent amendments

- 2004/108/EC dated 15/12/04

(Electromagnetic Compatibility) and

subsequent amendments

- 93/68/EEC dated 22/07/93 and subsequent

amendments.

- 2009/142/EC dated 30/11/06 (Gas) and

subsequent amendments

- 2012/19/EU and subsequent amendments.

22

GB

PC 640 /HA

R

S

A

Ta

ble 1 Liquid Gas Natural Gas

Nominal (mbar)

Minimum (mbar)

Maximum (mbar)

37

25

45

28-30

20

35

20

17

25

Rapid (R)

Semi Rapid (S)

Auxiliary (A)

Supply pressures

Burner

Diameter

(mm)

Thermal Power

kW (p.c.s.*)

100

75

55

3.00

1.65

1.00

Nomin. Reduc.

0.70

0.40

By-pass

1/100

(mm)

39

28

Nozzle

1/100

(mm)

Flow*

g/h

***

86

64

50

Nozzle

1/100

(mm)

Flow*

l/h

132(H)

96(Z)

79(6)

286

157

95

218

120

73

**

214

118

71

* At 15°C and 1013,25 mbar - dry gas

** Propane P.C.S. = 50.37 MJ/Kg

*** Butane P.C.S. = 49.47 MJ/Kg

Natural P.C.S. = 37.78 MJ/m

Burner and nozzle specifications

3

GB

23

Start-up and use

! The position of the corresponding gas burner is shown on every knob.

Gas burners

Each burner can be adjusted to one of the following settings using the

corresponding control knob:

● Off

Maximum

Minimum

To light one of the burners, hold a lit match or lighter near the burner and, at

the same time, press down and turn the corresponding knob anti-clockwise

to the maximum setting.

Since the burner is tted with a safety device, the knob should be pressed

for approximately 2-3 seconds to allow the automatic device keeping the

ame alight to heat up.

When using models with an gas burner ignition, to light the selected burner press

down and turn the corresponding knob anticlockwise to maximum position,

keeping it pressed until the burner has ignitied.

! If a ame is accidentally extinguished, turn off the control knob and wait for

at least 1 minute before trying to relight it.

To switch off the burner, turn the knob in a clockwise direction until it stops

(when reaches the “●” position).

Practical advice on using the burners

To ensure the burners operate efciently:

• Use appropriate cookware for each burner (see table) so that the ames

do not extend beyond the bottom of the cookware.

• Always use cookware with a at base and a cover.

• When the contents of the pan reach boiling point, turn the knob to minimum.

Rapid (R)

Semi Rapid (S)

Auxiliary (A)

Ø Cookware Diameter (cm)

24 - 26

16 - 20

10 - 14

Burner

To identify the type of burner, refer to the designs in the section entitled, “Burner

and Nozzle Specications”.

• For maximum stability, always make sure that the pan supports are

correctly tted and that each pan is placed centrally over the burner.

• Pan handles should be positioned in line with one of the support bars on

the pan support grid.

• Pan handle should be positioned so not to protrude beyond the front edge

of the hob.

The more variable aspect in terms of pan

stability can often be the pan itself, (or

the positioning of that pan during use).

Well balanced pans, with at bases that

are placed centrally over the burner,

with the pan handles aligned with one

of the support ngers obviously offer the

greatest stability.

Precautions and tips

! This appliance has been designed and manufactured in compliance with

international safety standards. The following warnings are provided for safety

reasons and must be read carefully.

General safety

• This is a class 3 built-in appliance.

• Gas appliances require regular air exchange to maintain efcient

operation. When installing the hob, follow the instructions provided

in the paragraph on “Positioning” the appliance.

• These instructions are only valid for the countries whose symbols

appear in the manual and on the serial number plate.

• The appliance was designed for domestic use inside the home and is

not intended for commercial or industrial use.

• The appliance must not be installed outdoors, even in covered areas. It is

extremely dangerous to leave the appliance exposed to rain and storms.

• Do not touch the appliance with bare feet or with wet or damp hands and

feet.

• The appliance must be used by adults only for the preparation of food,

in accordance with the instructions outlined in this booklet. Any other

use of the appliance (e.g. for heating the room) constitutes improper

use and is dangerous. The manufacturer may not be held liable for

any damage resulting from improper, incorrect and unreasonable

use of the appliance.

• The openings used for ventilation and dispersion of heat must never be

covered.

• Always make sure the knobs are in the “●”/“○” position when the appliance

is not in use.

• When unplugging the appliance always pull the plug from the mains socket,

do not pull on the cable.

• Never carry out any cleaning or maintenance work without having detached

the plug from the mains.

• In case of malfunction, under no circumstances should you attempt to repair

the appliance yourself. Repairs carried out by inexperienced persons may

cause injury or further malfunctioning of the appliance. Contact a Service

Centre (see Assistance).

• Do not use unstable or deformed pans.

• Do not close the glass cover (if present) when the gas burners or electric

hotplates are still hot.

• Do not leave the electric hotplate switched on without a pan placed on it.

• The appliance should not be operated by people (including children)

with reduced physical, sensory or mental capacities, by inexperienced

individuals or by anyone who is not familiar with the product. These

individuals should, at the very least, be supervised by someone who

assumes responsibility for their safety or receive preliminary instructions

relating to the operation of the appliance.

• Do not let children play with the appliance.

• The appliance is not intended to be operated by means of an external

timer or separate remote-control system.

Disposal

• When disposing of packaging material: observe local legislation so that

the packaging may be reused.

• The European Directive 2012/19/EU on Waste Electrical and Electronic

Equipment (WEEE), requires that old household electrical appliances must

not be disposed of in the normal unsorted municipal waste stream. Old

appliances must be collected separately in order to optimise the recovery

and recycling of the materials they contain and reduce the impact on

human health and the environment.The crossed out “wheeled bin” symbol

24

GB

on the product reminds you of your obligation, that when you dispose of

the appliance it must be separately collected.

Consumers should contact their local authority or retailer for information

concerning the correct disposal of their old appliance.

Respecting and conserving the environment

• Cook your food in closed pots or pans with well-tting lids and use as little

water as possible. Cooking with the lid off will greatly increase energy

consumption.

• Use purely at pots and pans.

• If you are cooking something that takes a long time, it’s worth using a

pressure cooker, which is twice as fast and saves a third of the energy.

Maintenance and care

Switching the appliance off

Disconnect your appliance from the electricity supply before carrying out

any work on it.

Cleaning the hob surface

• All the enamelled and glass parts should be cleaned with warm water and

neutral solution.

• Stainless steel surfaces may be stained by calcareous water or aggressive

detergents if left in contact for too long. Any food spills (water, sauce, coffee,

etc.) should be wiped away before they dry.

• Clean with warm water and neutral detergent, and then dry with a soft

cloth or chamois. Remove baked-on dirt with specic cleaners for stainless

steel surfaces.

• Clean stainless steel only with soft cloth or sponge.

• Do not use abrasive or corrosive products, chlorine-based cleaners or pan

scourers.

• Do not use steam cleaning appliances.

• Do not use ammable products.

• Do not leave acid or alkaline substances, such as vinegar, mustard, salt,

sugar or lemon juice on the hob.

Cleaning the hob parts

• Clean the enamelled and glass parts only with soft cloth or sponge.

• Grids, burner caps and burners can be removed to be cleaned.

• Clean them by hand with warm water and non-abrasive detergent,

removing any food residues and checking that none of the burner openings

is clogged.

• Rinse and dry.

• Ret burners and burner caps correctly in the respective housings.

• When replacing the grids, make sure that the panstand area is aligned

with the burner.

• Models equipped with electrical ignition plugs and safety device require

thorough cleaning of the plug end in order to ensure correct operation.

Check these items frequently, and if necessary, clean them with a damp

cloth. Any baked-on food should be removed with a toothpick or needle.

! To avoid damaging the electric ignition device, do not use it when the

burners are not in their housing.

Gas tap maintenance

Over time, the taps may become jammed or difcult to turn. If this happens,

the tap must be replaced.

! This procedure must be performed by a qualied technician authorised

by the manufacturer.

Troubleshooting

It may happen that the appliance does not function properly or at all. Before

calling the service centre for assistance, check if anything can be done. First,

check to see that there are no interruptions in the gas and electrical supplies,

and, in particular, that the gas valves for the mains are open.

The burner does not light or the ame is not even around the burner.

Check whether:

• The gas holes on the burner are clogged.

• All the movable parts that make up the burner are mounted correctly.

• There are draughts near the appliance.

The ame dies in models with a safety device.

Check to make sure that:

• You pressed the knob all the way in.

• You keep the knob pressed in long enough to activate the safety device.

• The gas holes are not blocked in the area corresponding to the safety

device.

The burner does not remain lit when set to minimum.

Check to make sure that:

• The gas holes are not blocked.

• There are no draughts near the appliance.

• The minimum setting has been adjusted properly.

The cookware is unstable.

Check to make sure that:

• The bottom of the cookware is perfectly at.

• The cookware is positioned correctly at the centre of the burner.

• The pan support grids have been positioned correctly.

Page is loading ...

68

UA

195130624.01

07/2015 - XEROX FABRIANO

Indesit Company S.p.A.

V

iale Aristide Merloni,47

60044 Fabriano (AN)

www.hotpoint.eu

Hotpoint Ariston PC 640 (BK)/HA User guide

Related papers

Other documents