DVD PLAYER/
VIDEO CASSETTE
RECORDER
OWNER’S MANUAL
MODEL :V192H
Before connecting, operating or adjusting this
product, please read this instruction booklet carefully
and completely.
PAL
FOR THE GUARANTEE TERMS & CONDITIONS,
PLEASE REFER TO BACK COVER OF THIS MANUAL.
Safety Precautions
This lightning flash with arrowhead symbol within
an equilateral triangle is intended to alert the
user to the presence of uninsulated dangerous
voltage within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation mark within an equilateral trian-
gle is intended to alert the user to the presence
of important operating and maintenance (servic-
ing) instructions in the literature accompanying
the product.
CAUTION: Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
Slots and openings in the cabinet are provided for ventilation
and to ensure reliable operation of the product and to protect it
from over heating.
The openings should be never be blocked by placing the prod-
uct on a bed, sofa, rug or other similar surface.This product
should not be placed in a built-in installation such as a book-
case or rack unless proper ventilation is provided or the manu-
facturer's instruction have been adhered to.
CAUTION:
This Digital Video Disc Player employs a Laser System.
To ensure proper use of this product, please read this
owner’s manual carefully and retain for future reference,
should the unit require maintenance, contact an authorized
service location-see service procedure.
Use of controls, adjustments or the performance of proce-
dures other than those specified herein may result in haz-
ardous radiation exposure.
To prevent direct exposure to laser beam, do not try to
open the enclosure.Visible laser radiation when open. DO
NOT STARE INTO BEAM.
CAUTION: The apparatus shall not be exposed to water,
dripping or splashing and that no objects filled with liquids,
such as vases, shall be placed on the apparatus.
This product is manufactured to comply with the
EEC DIRECTIVE 89/336/EEC, 93/68/EEC and
2006/95/EC.
Disposal of your old appliance
1.When this crossed-out wheeled bin symbol is
attached to a product it means the product is
covered by the European Directive 2002/96/EC.
2. All electrical and electronic products should be
disposed of separately from the municipal waste
stream via designated collection facilities appoint-
ed by the government or the local authorities.
3.The correct disposal of your old appliance will
help prevent potential negative consequences for
the environment and human health.
4. For more detailed information about disposal of
your old appliance, please contact your city office,
waste disposal service or the shop where you pur-
chased the product.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a
dedicated circuit;
That is, a single outlet circuit which powers only that
appliance and has no additional outlets or branch circuits.
Check the specification page of this owner's manual to be
certain.
Do not overload wall outlets. Overloaded wall outlets, loose
or damaged wall outlets, extension cords, frayed power
cords, or damaged or cracked wire insulation are
dangerous. Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage or
deterioration, unplug it, discontinue use of the appliance,
and have the cord replaced with an exact replacement part
by an authorized services.
Protect the power cord from physical or mechanical abuse,
such as being twisted, kinked, pinched, closed in a door, or
walked upon. Pay particular attention to plugs, wall
outlets,and the point where the cord exits the appliance.
To disconnect power from the mains, pull out the mains
cord plug.When installing the product, ensure that the plug
is easily accessible.
2
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
POWER: This unit operates on a mains supply of 200-240V~,
50/60Hz.
WIRING: This unit is supplied with a BSI 1363 approved 13
amp mains plug, fused at 5 amp. When replacing the fuse
always use a 5 amp BS 1362, BSI or ASTA approved type.
Never use this plug with the fuse cover omitted. To obtain a
replacement fuse cover contact your dealer or “LG Electronics
U.K.Ltd.” If the type of plug supplied is not suitable for the
mains sockets in your home, then the plug should be removed
and a suitable type fitted. Please refer to the wiring instruc-
tions below:
WARNING: A mains plug removed from the mains lead of this
unit must be destroyed.A mains plug with bared wires is haz-
ardous if inserted in a mains socket.
Do not connect either wire to the earth pin, marked with the
letter E or with the earth symbol or coloured green or
green and yellow.
If any other plug is fitted, use a 5 amp fuse, either in the plug,
or at the distribution board.
IMPORTANT: The wires in this mains lead are coloured in
accordance with the following codes:
- BLUE: NEUTRAL, BROWN: LIVE - As the colours of the
wires in the mains lead of this unit may not correspond with
the coloured marking indentifying the terminals in your plug,
proceed as follows: The wire which is coloured blue must be
connected to the terminal which is marked with the letter N or
coloured black. The wire which is coloured brown must be
connected to the terminal which is marked with the letter L or
coloured red.
Introduction
3
Table of Contents
Introduction
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . 2
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
About the Symbol Display . . . . . . . . . . . . . . 4
Symbol used in this Manual . . . . . . . . . . . . . . . 4
Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . 4
Handling Discs . . . . . . . . . . . . . . . . . . . . . . . . . 4
Storing Discs . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Cleaning Discs . . . . . . . . . . . . . . . . . . . . . . . . . 4
Selecting the Viewing Source . . . . . . . . . . . . . . 4
Types of Playable Discs. . . . . . . . . . . . . . . . . . . 5
Regional Code . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Preparation
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-11
Connecting to a TV & Decoder(or Satellite) . . . . . 9
Resolution setting . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Connecting to Optional Equipment. . . . . . . . . . . . . . 10
HDMI Connection . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Before Operation-VCR part . . . . . . . . . . . . . . . 12-16
Tuning in a video channel on your TV. . . . . . . . . 12
Using your VCR for the very first time. . . . . . . . . 12
Setting the clock Manually . . . . . . . . . . . . . . . . . 13
To set the colour system . . . . . . . . . . . . . . . . . . 13
How to use the main menu. . . . . . . . . . . . . . . . . 14
Tuning in TV Stations Automatically . . . . . . . . . . 14
Tuning in TV Stations Manually. . . . . . . . . . . . . . 15
Changing the order of TV Stations . . . . . . . . . . . 16
Deleting TV Stations . . . . . . . . . . . . . . . . . . . . . 16
Before Operation-DVD part . . . . . . . . . . . . . . . 17-20
Displaying Disc Information on-screen . . . . . . . . 17
Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 17
General Operation . . . . . . . . . . . . . . . . . . . . . . . 17
LANGUAGE. . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Menu Language. . . . . . . . . . . . . . . . . . . . . . 18
Disc Audio / Subtitle / Menu. . . . . . . . . . . . . 18
DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
TV Aspect . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Display Mode. . . . . . . . . . . . . . . . . . . . . . . . 18
TV Output Select . . . . . . . . . . . . . . . . . . . . . 18
AUDIO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Dolby Digital / DTS / MPEG. . . . . . . . . . . . . 19
Sample Freq. (Frequency) . . . . . . . . . . . . . . 19
DRC (Dynamic Range Control) . . . . . . . . . . 19
Vocal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
LOCK (Parental Control) . . . . . . . . . . . . . . . . . . 19
Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Password (Security Code) . . . . . . . . . . . . . . 19
Area Code. . . . . . . . . . . . . . . . . . . . . . . . . . 20
OTHERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
PBC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Auto Play . . . . . . . . . . . . . . . . . . . . . . . . . . 20
DivX(R) VOD . . . . . . . . . . . . . . . . . . . . . . . . 20
Operation
Operation with tape . . . . . . . . . . . . . . . . . . . . . 21-24
Playing a tape . . . . . . . . . . . . . . . . . . . . . . . . . . 21
CM (Commercial Message) Skip . . . . . . . . . 21
OPR (Optimum Picture Response). . . . . . . . 21
Instant Timer Recording. . . . . . . . . . . . . . . . . . . 22
Timer recording using On Screen Display . . . 23-24
Additional Operation - VCR part . . . . . . . . . . . . 25-27
Hi-Fi Stereo Sound System . . . . . . . . . . . . . . . . 25
On Screen Display (F.OSD) . . . . . . . . . . . . . . . . 25
Tape Counter Memory Stop . . . . . . . . . . . . . . . . 25
To set the decoder . . . . . . . . . . . . . . . . . . . . . . . 25
Video Doctor (Self-Diagnosis) . . . . . . . . . . . . . . 26
Lock (Child Lock). . . . . . . . . . . . . . . . . . . . . . . . 26
Wide Screen Compatibility 16:9 . . . . . . . . . . . . . 26
1W Mode (Power save mode) . . . . . . . . . . . . . . 26
Recording from External Components . . . . . . . . 27
Copying from DVD to VCR . . . . . . . . . . . . . . . . . 27
General Playback features - DVD Part . . . . . . . . . 28
Playing a DVD or Video CD . . . . . . . . . . . . . . . . . . 29
Additional features . . . . . . . . . . . . . . . . . . . . . . . 29
3D Surround . . . . . . . . . . . . . . . . . . . . . . . . 29
Time Search . . . . . . . . . . . . . . . . . . . . . . . . 29
Marker Search . . . . . . . . . . . . . . . . . . . . . . 29
Last Scene Memory . . . . . . . . . . . . . . . . . . 29
Screen Saver . . . . . . . . . . . . . . . . . . . . . . . 29
Playing an Audio CD or MP3/WMA file . . . . . . . . 30
Programmed Playback. . . . . . . . . . . . . . . . . . . . 30
Repeat Programmed Tracks. . . . . . . . . . . . . 30
Erasing a Track from Program List . . . . . . . . 30
Erasing the Complete Program List . . . . . . . 30
Viewing a JPEG file . . . . . . . . . . . . . . . . . . . . . . . 31
Slide Show. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Still Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Moving to another File . . . . . . . . . . . . . . . . . . . . 31
Zoom. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
To rotate picture. . . . . . . . . . . . . . . . . . . . . . . . . 31
To listen to MP3 music while watching picture . . 31
Playing a DivX Movie file . . . . . . . . . . . . . . . . . . . 32
Playing a DVD VR format Disc . . . . . . . . . . . . . . . 33
Additional Operation. . . . . . . . . . . . . . . . . . . . . . . 34
Controlling other TVs with the remote control . . . 34
Maintenance and Service. . . . . . . . . . . . . . . . . . 34
Reference
Language and Area Code List . . . . . . . . . . . . . . . 35
Language Code List. . . . . . . . . . . . . . . . . . . . . . 35
Area Code List. . . . . . . . . . . . . . . . . . . . . . . . . . 35
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
To ensure proper use of this product, please read this
owner’s manual carefully and retain for future reference.
This manual provides information on the operation and
maintenance of your DVD player. Should the unit require
service, contact an authorized service location.
About the Symbol Display
“ ” may appear on your TV display during operation
and indicates that the function explained in this owner’s
manual is not available on that specific DVD video disc.
Symbol Used in this Manual
Note:
Indicates special notes and operating features.
Tip:
Indicates tips and hints for making the task easier.
A section whose title has one of the following symbols is
applicable only to the disc represented by the symbol.
All discs listed below
DVD and finalized DVD±R/RW
Video CDs
Audio CDs
MP3 files
WMA files
DivX files
Notes on Discs
Handling Discs
Do not touch the playback side of the disc. Hold the disc
by the edges so that fingerprints do not get on the
surface. Never stick paper or tape on the disc.
Storing Discs
After playing, store the disc in its case. Do not expose
the disc to direct sunlight or sources of heat and never
leave it in a parked car exposed to direct sunlight.
Cleaning Discs
Fingerprints and dust on the disc can cause poor
picture quality and sound distortion. Before playing,
clean the disc with a clean cloth.Wipe the disc from the
center out.
Do not use strong solvents such as alcohol, benzine,
thinner, commercially available cleaners, or anti-static
spray intended for older vinyl records.
DivX
WMA
MP3
ACD
VCD
DVD
ALL
Before Use
4
Notes:
• If you insert a disc while this unit is in the VCR mode,
this unit will switch to DVD mode automatically.
• If you insert a cassette tape without prevention tab
while this unit is in the DVD mode, this unit will switch
to VCR mode automatically.
Selecting the Viewing Source
You must select one of your output sources (DVD or
VCR) to view on the TV screen.
If you want to view DVD deck output source:
Press DVD until DVD indicator in the display window
lights and output source of DVD deck is viewed on the
TV screen.
If you want to view VCR deck output source:
Press VCR until VCR indicator in the display window
lights and output source of VCR deck is viewed on the
TV screen.
Types of Playable Discs
DVD
(8 cm / 12 cm disc)
Video CD (VCD)
(8 cm / 12 cm disc)
Audio CD
(8 cm / 12 cm disc)
In addition, this unit plays DVD±R/RW, CD-R/RW and
SVCD that contains audio titles, DivX, MP3, WMA,
and/or JPEG files.
This indicates a product feature that is capable
of playing DVD-RW discs recorded with Video
Recording format.
Notes:
• Depending on the conditions of the recording
equipment or the CD-R/RW (or DVD±R/RW) disc
itself, some CD-R/RW (or DVD±R/RW) discs cannot
be played on the unit.
• Do not use irregularly shaped CDs (e.g., heart-
shaped or octagonal) since they may result in
malfunctions.
• This unit requires discs and recordings to meet
certain technical standards in order to achieve optimal
playback quality. Pre-recorded DVDs are automatically
set to these standards.There are many different types
of recordable disc formats (including CD-R containing
MP3 or WMA files) and these require certain pre-
existing conditions (see above) to ensure compatible
playback.
Customers should note that permission is
required in order to download MP3 / WMA files
and music from the Internet. Our company has no
right to grant such permission. Permission should
always be sought from the copyright owner.
Regional Code
This unit has a regional code printed on the rear of the
unit.This unit can play only DVD discs labelled same as
the rear of the unit or “ALL”.
Notes on Regional Codes
•Most DVD discs have a globe with one or more num-
bers in it clearly visible on the cover.This number
must match your unit’s regional code or the disc can-
not play.
• If you try to play a DVD with a different regional code
from your player, the message “Check Regional
Code” appears on the TV screen.
Notes on Copyrights:
It is forbidden by law to copy, broadcast, show,
broadcast via cable, play in public, or rent copyrighted
material without permission.This product features the
copy protection function developed by Macrovision.
Copy protection signals are recorded on some discs.
When recording and playing the pictures of these discs
picture noise will appear. This product incorporates
copyright protection technology that is protected by
method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision
Corporation and other rights owners. Use of this
copyright protection technology must be authorized by
Macrovision Corporation, and is intended for home and
other limited viewing uses only unless otherwise
authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DEFINITION TELEVISION SETS ARE FULLY COMPATI-
BLE WITH THIS PRODUCT AND MAY CAUSE ARTI-
FACTS TO BE DISPLAYED IN THE PICTURE. IN CASE
OF 625 PROGRESSIVE SCAN PICTURE PROBLEMS,
IT IS RECOMMENDED THAT THE USER SWITCH THE
CONNECTION TO THE ‘STANDARD DEFINITION’
OUTPUT. IF THERE ARE QUESTIONS REGARDING
OUR TV SET COMPATIBILITY WITH THIS MODEL
625p DVD PLAYER, PLEASE CONTACT OUR
CUSTOMER SERVICE CENTER.
Introduction
5
Before Use (Continued)
6
Front Panel
1.
11//
I
Switches the unit to ON or OFF.
2. Disc Tray
Insert a disc here.
3. PROG. (V
/v)
Channel Programme Selectors
.
4. DVD
Opens or closes the disc tray.
5. Display window
Shows the current status of the unit.
DVD: DVD deck is selected.
:
A disc is loaded in the DVD deck.
[P]: Indicates the Progressive Scan is set to On mode.
:
Indicates repeat mode.
:
Child Lock is engaged.
:
DVD+VCR is in timer recording or a timer
recording is programmed.
:
A Cassette is in the VCR deck.
VCR: VCR deck is selected.
REC:
VCR recording is engaged.
DVD to VHS copy is in progress.
TV: Indicates TV mode.
(See Notes on page 22.)
:
Indicates total playing time/elapsed
time/current time.
6. Remote Sensor
Point the remote control here.
7. Tape Compartment
8. DVD/VCR
DVD/VCR Selector
9.
ÁÁ
Stops playback.
10.
..//mm
Go to beginning of current chapter/track or to
PREVIOUS chapter/track.
Press and hold for two seconds for a fast reverse
search. Rewinds the tape.
11.
NN
Starts playback.
12.
MM//>>
Go to NEXT chapter/track.
Press and hold for two seconds for a fast forward
search.Winds the tape forwards.
13.Video IN Jack
14.
Audio IN (L/R) Jacks
15. VCR
Tape Eject
16.
OO
VCR Record
17.RES. (RESOLUTION)
You can change the resolution depending on your TV.
- HDMI mode :You can switch among the 576p, 720p or
1080i resolution.
- Component mode :You can switch among 576i, 576p,
720p resolution.
1716
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Introduction
7
Remote Control
POWER
Switch this unit ON or OFF.
DVD/VCR select button
Selects operational mode of
remote control.
OPEN/CLOSE
EJECT
Open or close the disc tray.
Tape Eject.
0-9 numerical buttons
Select numbered items in a menu.
TV/VCR
Switch between your TV’s tuner
and the VCR’s internal tuner.
AV
Select input source for recording
into tape.
BACKWARD / FORWARD
(m / M)
DVD: Search backward or forward.
VCR: Rewinds the tape during the
STOP mode, for fast reverse picture
search and Advances the tape during
the STOP mode, fast forward picture
search.
SKIP (. / >)
Go to next chapter or track.
Returns to beginning of current
chapter or track or go to previous
chapter or track.
PAUSE/STEP (X)
Pause playback temporarily / press
repeatedly for frame-by-frame
playback.
PLAY (
NN
)
Starts playback.
STOP (
ÁÁ
)
Stops playback.
MARKER
Mark any point during playback.
SEARCH
Display MARKER SEARCH menu.
CLEAR
Clear a track number on the
program menu or a mark on the
MARKER SEARCH menu.
Reset tape counter to zero.
REPEAT
Repeat chapter, track, title, all.
A-B/LP
Repeat sequence.
Select the recording speed of the
tape.
TV Control Buttons (see p. 34)
TV POWER: Tur ns on or off the TV.
TV AV: Selects the TV’s source.
TV PR +/–: Selects TV’s channel.
TV VOL +/–: Adjusts TV’s volume.
DISPLAY
CLK/CNT
Access the On-Screen Display.
Shows you the current time or
counter.
FGDE(left/right/up/down)
Select an item in the menu.
PR/TRK(+/-
)
Select channel programme of VCR.
To adjust tracking.
To control vertical tremble during
picture still.
ENTER/OK
Acknowledge menu selection.
DISC MENU
Access menu of a DVD disc.
SETUP/ i
Access or remove setup menu.
RETURN
Displays the menu of a video CD
with PBC.
AUDIO
Select an audio language (DVD).
SUBTITLE
Select a subtitle language.
ANGLE
Select DVD camera angle if available
ZOOM
Enlarge video image.
REC/ITR (
OO
)
Record your input sources into tape.
LOCK (Child Lock)
Switch the Child Lock on and off.
TITLE
Display the title menu of the disc if
available.
PROGRAM
Access or remove program menu.
RANDOM/CM SKIP
Play tracks in random order.
CM SKIP
RESOLUTION
You can change the resolution
depending on your TV.
* This button is not available.
Remote Control Operation
Point the remote control at the remote sensor and press
the buttons.
Do not mix old and new batteries and never mix
different types of batteries such as standard,
alkaline, etc.
Remote control battery installation
Detach the battery cover on the rear of the
remote control, and insert two batteries (size
AAA) with 3 and # aligned correctly.).
AAA
AAA
8
Rear Panel
Do not touch the inner pins of the jacks on the rear panel.
Electrostatic discharge may cause permanent damage to the unit.
AUDIO OUT (Left/Right) (DVD EXCLUSIVE OUT)
Connect to an amplifier, receiver or stereo system.
VIDEO/AUDIO OUT(Left/Right) (DVD/VCR OUT)
Connect to a TV with video and audio inputs.
AERIAL
Connect the aerial using this jack.
COAXIAL (Digital audio out jack)
(DVD EXCLUSIVE OUT)
Connect to digital (coaxial) audio equipment.
RF.OUT
Connect to your TV using this jack.
EURO AV1 AUDIO/VIDEO (VCR IN+OUT / DVD OUT)
Connect to your TV set or another video recorder.
AC Power Cord
Connect to a power source.
COMPONENT/PROGRESSIVE SCAN VIDEO OUT (Y Pb Pr)
(DVD EXCLUSIVE OUT)
Connect to a TV with Y Pb Pr inputs.
EURO AV2 DECODER
Connect to pay-TV decoder or another video recorder.
OPTICAL (Digital audio out jack)
Connect to digital (optical) audio equipment.
HDMI OUT
HDMI output providing a high
quality interface for digital
audio and video (see p. 11)
.
S-VIDEO OUT (DVD EXCLUSIVE OUT)
Connect to a TV with S-Video input.
Preparation
9
Connections
Caution:
Make sure this unit is connected directly to the TV. Set
the TV to the correct video input channel.
Do not connect this unit’s AUDIO OUT jack to the
phone in jack (record deck) of your audio system.
Connecting to a TV & Decoder
(or Satellite)
Make one of the following connections, depending on
the capabilities of your existing equipment.
Basic connection (AV)
1. Connect the EURO AV1 AUDIO/VIDEO on the rear
panel of this unit to the SCART input socket on the
TV using a SCART lead (T1).
2. Some TV broadcasters transmit encoded television
signals which you can only see with a purchased or
rented decoder.You can connect such a decoder
(descrambler) to this unit (T2).
or
1. Connect the VIDEO (DVD/VCR OUT) jacks on the
DVD Player to the corresponding in jacks on the TV
using the video cable (V).
2. Connect the Left and Right or AUDIO (DVD/VCR
OUT) jacks of the DVD+VCR to the audio left/right in
jacks on the TV using the audio cables (A1).
Notes:
If you use this connection, set the TV’s source
selector to VIDEO.
For DVD/VCR VIDEO OUT jack connection, resolu-
tion must be set to 576i or 576p, however DVD/VCR
VIDEO OUT is always at 576i standard resolution.
The encoded television signals (CANAL+ or
PREMIERE) are not decoded in the 1W Mode
(see p. 26).
Basic connection (RF)
1. Connect the RF antenna cable from your indoor/
outdoor antenna to AERIAL jack on the rear panel of
this unit.
2. Connect the supplied RF antenna cable from the
RF.OUT jack on the rear panel of this unit to your
television’s Antenna Input (R).
S-Video connection
1. Connect the S-VIDEO OUT jack on this unit to the
S-Video input jack on the TV using the S-Video
cable (S).
2. Connect the Left and Right AUDIO OUT or DVD/VCR
AUDIO OUT jacks of the DVD Player to the audio
left/right in jacks on the TV using the audio cables
(A1).
Note:
For S-Video connection, resolution must be set to 576i
or 576p, however S-VIDEO OUT is always at 576i
standard resolution.
DVD exclusive out connection
Component Video /
Progressive Scan connection
If your television is a high-definition or “digital ready”
television, you may take advantage of the DVD
Player’s progressive scan output for the highest video
resolution possible.
If your TV does not accept the Progressive Scan
format, the picture will appear scrambled if you try
Progressive Scan on the DVD Player.
1. Connect the COMPONENT / PROGRESSIVE SCAN
VIDEO OUT jacks on the DVD Player to the
corresponding in jacks on the TV using the Y Pb Pr
cable (C).
2. Connect the Left and Right AUDIO OUT jacks of this
unit to the audio left/right in jacks on the TV using
the audio cables (A2).
Notes:
The 576p and 720p resolutions are Progressive scan
applied resolutions.
Progressive scan does not work with the analog video
connections (yellow VIDEO OUT jack) or S-VIDEO.
AUDIO INPUT
L
R
AERIAL
Rear of TV
Rear of this unit (Basic connection)
COMPONENT VIDEO INPUT/
PROGRESSIVE SCAN
Pr
Pb Y
VIDEO
INPUT
Decoder (or Satellite)
SCART INPUT
R
S
VA1
T2
T1
S-
VIDEO INPUT
AUDIO INPUT
L
R
AERIAL
Rear of TV
Rear of this unit (DVD exclusive out connection)
COMPONENT VIDEO INPUT/
PROGRESSIVE SCAN
Pr
Pb Y
VIDEO
INPUT
SCART INPUT
C A2
10
Connections (Continued)
Resolution setting
The resolution setting support only DVD playback.
1. Before you set the resolution, this unit must be in
stop mode. Press STOP to stop playback.
2. Press RESOLUTION once.The current resolution
setting will be appears in the display window.
3. Press RESOLUTION repeatedly to change the
resolution you want.
The available resolution according to the connections
are as shown below.
OUTPUT
CONNECTIONS
HDMI
VIDEO OUT
COMPONENT
VIDEO OUT
SCARTi
S-VIDEOi
Note:
For 720p resolution on the component video out, only
non-copy protected discs can be played back.If the
disc is copy protected, it will be displayed at the 576p
resolution without HDMI cable connection.With HDMI
cable connection, the picture may not be displayed
properly
If your TV does not support the resolution you have
set, the picture may not be displayed properly. Please
read TV’s owner’s manual then set the resolution that
your TV can accept.
Connecting to Optional Equipment
Connecting to an amplifier equipped with two chan-
nel analog stereo or Dolby Pro Logic II/Pro Logic
Connect the Left and Right DVD/VCR AUDIO OUT or
AUDIO OUT (DVD EXCLUSIVE OUT) jacks on this unit
to the audio left and right in jacks on your amplifier,
receiver or stereo system, using the audio cables.
Connecting to an amplifier equipped with two channel
digital stereo (PCM) or to an Audio/ Video receiver
equipped with a multi-channel decoder (Dolby
Digital™, MPEG 2 or DTS)
1. Connect one of this unit’s DIGITAL AUDIO OUT jack
(OPTICAL or COAXIAL) to the corresponding in jack
on your amplifier. Use an optional digital (optical or
coaxial) audio cable.
2. You will need to activate this unit’s digital output.
(See “AUDIO” on page 19).
Digital Multi-channel sound
A digital multi-channel connection provides the best
sound quality. For this you need a multi-channel
Audio/Video receiver that supports one or more of the
audio formats supported by your unit (MPEG 2, Dolby
Digital and DTS). Check the receiver manual and the
logos on the front of the receiver.
Warning:
Due to the DTS Licensing agreement, the digital output
will be in DTS digital out when DTS audio stream is
selected.
Notes:
If the audio format of the digital output does not match
the capabilities of your receiver, the receiver will
produce a strong, distorted sound or no sound at all.
To see the audio format of the current DVD in the
On-Screen Display, press AUDIO.
L
R
AUDIO INPUT
DIGITAL INPUT
COAXIAL
Amplifier (Receiver)
Rear of this unit
Digital multi-channel connection
(DVD exclusive out connecttion)
DVD exclusive out
DVD/VCR OUT
Rear of this unit
or
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are
trademarks of Dolby Laboratories.
DTS and DTS Digital Out are trademarks of Digital
Theater Systems, Inc.
Available Resolutions
1920 x 1080i, 1280 x 720p,
720 x 576p
1280 x 720p, 720 x 576p,
720 x 576i
720 x 576i
720 x 576i
Preparation
11
If you have a HDMI TV or monitor, you can connect it to
this DVD+VCR using a HDMI cable.
1. Set the TV’s source to HDMI (refer to TV’s Owner’s
manual).
2. Connect the HDMI OUT jack on the unit to the HDMI
jack on a HDMI compatible TV or monitor (H).
3. Press RESOLUTION repeatedly to select the
desired resolution.
Notes :
• Both PCM and Bitstream Audio out is available,
when the sample frequency is set to 48
kHz
in HDMI
connection.
• If Audio setup is set to bitstream and your TV does
not support Bitstream Audio out in HDMI connection,
audio sound may not output or distorted.
• When the no sound or noisy sound are output with
HDMI connection, set the Audio option [Dolby
Digital, DTS or MPEG] in the SETUP menu to PCM
or Off.
•
The arrow on the cable connector body should be
face up for correct alignment with the connector on
the DVD+VCR.
•
If there is noise or lines on the screen, please check
the HDMI cable.
• Not all HDCP-compatible DVI devices will work with
this unit.
• If your HDMI TV does not support HDCP, the blue
screen appears on the screen.
•
If the abnormal picture appears on the TV screen in
HDMI connection, turn off the unit and then turn the
unit on again.
Tip:
• When you use HDMI connection, you can change the
resolution (576i, 576p, 720p, 1080i) for the HDMI
output.
• The HDMI will out at 576p resolution,even if you set
the resolution to 576i on the HDMI connection.
About HDMI
HDMI (High Definition Multimedia Interface) supports
both video and audio on a single digital connection for
use with DVD players, Set-Top boxes, and other AV
devices.
HDMI was developed to provide the technologies of
HDCP (High-bandwidth Digital Content Protection).
HDCP is used to protect digital content transmitted and
received.
HDMI has the capability to support standard, enhanced,
or high-definition video plus standard to multi-channel
surround-sound audio, HDMI features include uncom-
pressed digital video, a bandwidth of up to 5 gigabytes
per second, one connector (instead of several cables
and connectors), and communication between the AV
source and AV devices such as DTVs.
HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI licensing LLC.
HDMI
HDMI compatible TV
Rear of DVD+VCR
H
HDMI Connection
12
Before Operation-VCR part
Tuning in a video channel on your
TV
Video channel (RF output channel) is the channel on
which your TV receives picture and sound signals from
the DVD+VCR through the RF cable.
If you have used a SCART lead you will not have to
tune your TV, simply select the AV channel.The AV
channel is already pre-tuned for optimum video play-
back on your TV.
Perform the following steps only if interference appears
in the TV picture after you have moved to a different
area or a new station has started broadcasting in your
area, or if you change the connection from RF connec-
tion to AV connection, or vise versa.
1. Turn on DVD+VCR and TV.
2. Set the vacant position 36 on your TV.
3. Press POWER on the remote control to enter the
stand by mode (the clock indicator will be
dimmed).
4. Press and hold PROG. (
vv
or
VV
) on the DVD+VCR
for more than 4 seconds.
RF 36 will appear in the display.
The following picture will be displayed on the TV
screen.
If the picture is snowy, move to step 5. If the picture
is clean, press POWER on the DVD+VCR to finish.
5. Press PROG. (
vv
or
VV
) on the DVD+VCR to set the
video channel to a vacant position between 22 and
68 which is not occupied by any local station in your
area.
Note:
The RF channel will not change until step 6 has
been executed.
6. Press POWER to store the new RF video channel
into the DVD+VCR memory.
Now tune your TV set to the new DVD+VCR RF
channel.
Note
If the TV picture was clear in step 4, do not retune your
TV.
Using your VCR for the very first
time
Following picture will display on the TV screen when
you have just connected your video recorder for the
very first time.
To make tuning TV stations, please follow stages 3 to 4
as shown "ACMS" (see p.14).
RF CHANNEL 36
ACMS
OK
i
Pr-12
ACMS
Preparation
13
Before Operation-VCR part
Setting the clock Manually
The clock in your DVD+VCR controls time and date set-
tings for your DVD+VCR.
The clock is set automatically during ACMS (Automatic
Channel Memory System) when your DVD+VCR
detects a channel that broadcasts a Teletext signal.
If the broadcast signal is weak the clock will not be set
and will require setting manually.
1. Press i.
Press
bb
or
BB
to select SET.
Press ENTER/OK.
The ACSS mode can be set to “OFF” by pressing
ENTER/OK if you want to set the time manually.
2. Use the
vv
or
VV
on the remote control to alter the
HOURS, MINUTES, DAY, MONTH and YEAR.
Please note your DVD+VCR uses a 24 hour clock.
e.g. 1pm will be displayed as 13:00.
The day of the week will appear automatically when
you enter the year.
3. If you make a mistake press
bb
or
BB
and enter the
correct details.
4. Press i to return to a TV picture.
To set the colour system
1. Press i.
2. The main menu will appear on the TV screen.
3. Press 1 or 2 to select the SYS and press
ENTER/OK.
4. Press 3 or 4 to select according to the COLOUR
system used.
5. Press 2 to select the RF AUDIO.
Press 3 or 4 to select according to the RF AUDIO
used.
6. Press i to remove the menus from the TV screen.
HH MM DD MM YY
:..- -
- -
- - - -
- - - - -
ACSS : ON
i
OK
12
SET
HH MM DD MM YY
:..00 1 01 06 SUN 8
ACSS : OFF
i
OK
12
SET
SYS
12
SET
OSD
ON
OFF
OSD
f
i
SYS
SYS
12
SET
OSD
ON
OFF
OSD
f
i
SYS
14
Before Operation-VCR part
How to use the main menu
This DVD+VCR can easily be programmed by using the
menus displayed on screen.
The menus are controlled by the Remote Control
Handset.
1. Switch on your TV set and DVD+VCR by pressing the
POWER button.
2. Press i button.
The main menu will appear on the TV screen.
REC - Timer recording setting (see p. 23).
PR SET - Manual tuning setting (see p. 15).
ACMS - ACMS (Automatic Channel Memory
System) (see p. 14).
SET - Date & clock setting (see p. 13).
SYS - To set the Colour TV System (see p. 13).
1 W ON/OFF - Power Save Mode (see p. 26).
(Dr.) - To check a problem with your VCR
(see p. 26).
F.OSD ON/OFF - To display the operational
mode of your VCR
(see p. 25).
(16:9/4:3) - To select the aspect ratio of your
TV (see p. 26).
DECODER - To use a pay-TV decoder
(or Satellite) with your VCR
(
see p. 25
).
(OPR) - To improve the playback picture
(see p. 21).
Appear when playback only.
Tip
You can change the menu language on the DVD setup
menu. (See the Menu Language on page 18.)
3. Press 1 and 2 to select the desired menu.
Press ENTER/OK and use 3 or 4 to select.
4. Press i to return to a TV picture.
Tuning in TV Stations Automatically
If the TV broadcast signal is weak your DVD+VCR may
not detect the necessary information and will not be
able to store them correctly.To overcome this problem
please turn to the MANUAL TUNING section on page
15.
1. Press POWER to turn on your DVD+VCR.
2. Press i button.
The main menu will appear on the TV screen.
Press 1 or 2 to select the ACMS.
Press ENTER/OK.
3. Press OK to again to start the automatic tuning
process.
4. The TV STATION TABLE will appear when tuning is
completed.
Press i to save your settings.
Notes:
Please note currently only a limited number of TV
companies transmit the Programme Delivery Control
(PDC) signal which enables your DVD+VCR to
successfully identify and store them. If your DVD+VCR
has difficulty in identifying a TV station please turn the
page to find out how to manually tune in and name a TV
station.While automatic tuning is taking place the time
and date will set automatically.
If - - :- - appears in the DVD+VCR display it means that
the broadcast signal is weak and the clock was not set.
Please turn to CLOCK SET section of this book on
page 13.
SYS
12
SET
OSD
ON
OFF
OSD
f
SYS
12
SET
OSD
ON
OFF
OSD
f
ACMS
Pr-12
ACMS
Pr-12
OK
i
ACMS
OK
i
Pr-12
ACMS
01 C02 00
02 C03 00
03 C04 00
ES
i
Pr-12
ACMS
BBC1
BBC2
ITV
OK
i
,DELETE :
MOVE :
P
SET
R
02 C03 00
03 C04 00
04 C05 00
05 C06 00
06 - - - -
07 - - - -
08 - - - -
01 C02 00
BBC2
ITV
CH4
CH5
- - - - -
- - - - -
- - - - -
BBC1
Preparation
15
Before Operation-VCR part
Tuning in TV Stations Manually
In certain areas of the country broadcast signals may
be too weak for your DVD+VCR’s automatic tuning
process to find or assign TV stations correctly.
You must tune in these weaker broadcast stations
manually in order for your DVD+VCR to store them.
1. Press i.
The main menu will appear on the TV screen.
Press
1 or 2 to select the PR SET.
Press ENTER/OK.
2. Press i.
The station table will appear.
3. Press 3 or 4 to select the programme number that
you want to tune (for example, PR 04).
4. Press ENTER/OK.
Press AV to select C (Standard stations) or S
(Cable stations):
C02 - C69, S01 - S41.
Enter the channel number of station that you want
to
tune, use 3 or 4 to find the required station.
5. Searching will stop when it locates a stations.
Press 2 to select MFT.
Control the fine tuning of the station by using 3 or
4
.
6. Press 2 to select STATION so that you may name
your TV station.
Press ENTER/OK.
7. Use 3 or 4 to select letters and numbers for the
station name.
Use 1 or 2 to move back and forth between
characters.
Press ENTER/OK.
8. Press i, confirm the station placement.
If you wish to manually tune other stations repeat
stages 3 - 8.
9. Press i again.
Your new TV station has now been tuned into your
DVD+VCR.
SYS
12
SET
OSD
ON
OFF
OSD
f
ACMS
Pr-12
P
SET
R
P
SET
R
PR CH MFT STATION
01 00
CHANNEL/CABLE : AV
C03
P
SET
R
i
PR-03
02 C02 00 PR-02
03 C03 00 PR-03
04 - - - - - - - - -
05 - - - - - - - - -
06 - - - - - - - - -
07 - - - - - - - - -
08 - - - - - - - - -
01 C01 00 PR-01
OK
i
,DELETE :
MOVE :
P
SET
R
PR CH STATION
04 - - - - - -
MFT
P
SET
R
C - -
i
CHANNEL/CABLE : AV
PR CH MFT
04 00C04
i
OK
STATION
P
SET
R
-
PR CH MFT
STATION
04 00
C04
PR-04
i
OK
P
SET
R
02 C02 00 PR-02
03 C03 00 PR-03
04 C04 00 PR-04
05 - - - - - - - - -
06 - - - - - - - - -
07 - - - - - - - - -
08 - - - - - - - - -
01 C01 00 PR-01
OK
i
,DELETE :
MOVE :
P
SET
R
PR CH STATION
04 00
C04
MFT
CHANNEL/CABLE : AV
i
P
SET
R
i
16
Before Operation-VCR part
Changing the order of TV Stations
After tuning TV stations into your DVD+VCR you may
wish to change the order in which they are stored with-
out having to retune them again.The instructions given
on this page will show you how you can simply move
them into your desired order.
1. Press i.
The main menu will appear on the TV screen.
Press 1 or 2 to select the PR SET.
Press ENTER/OK.
2. Press i.
Press 3 or 4 to select the programme number you
want to move (for example, PR-03).
Press 2.
3. Press 3 or 4 to select the programme number you
want to move to (for example, PR-05).
4. Press ENTER/OK.
The selected programme will be moved to the new
programme number.
If you wish to move other TV stations repeat stages
1 - 4.
5. Press i to remove the menus from the TV screen.
Deleting TV Stations
After tuning TV stations into your DVD+VCR you may
wish to delete a station.
The instructions given on this page will show you how
you can easily delete any unwanted TV stations.
1. Press i.
The main menu will appear on the TV screen.
Use 1 or 2 to select the PR SET.
Press ENTER/OK.
2. Press i.
3. Press 3 or 4 to select the programme number you
want to delete. (for example, PR-01)
4. Press 1.
After a short while, the selected station will be
deleted.
If you wish to delete other TV stations repeat stages
3 - 4.
5. Press i to remove the menus from the TV screen.
SYS
12
SET
OSD
ON
OFF
OSD
f
ACMS
Pr-12
P
SET
R
P
SET
R
PR CH MFT STATION
01 00 PR-03
CHANNEL/CABLE : AV
C03
i
P
SET
R
02 C02 00 PR-02
03 C03 00 PR-03
04 C04 00 PR-04
05 - - - - - - - - -
06 - - - - - - - - -
07 - - - - - - - - -
08 - - - - - - - - -
01 C01 00 PR-01
OK
i
,DELETE :
MOVE :
P
SET
R
02 C02 00 PR-02
03 C03 00 PR-03
04 C04 00 PR-04
05 - - - - - - - - -
06 - - - - - - - - -
07 - - - - - - - - -
08 - - - - - - - - -
01 C01 00 PR-01
P
SET
R
OK
i
02 C02 00 PR-02
03 C04 00 PR-04
04 - - - - - - - - -
05 C03 00 PR-03
06 - - - - - - - - -
07 - - - - - - - - -
08 - - - - - - - - -
01 C01 00 PR-01
P
SET
R
OK
i
SYS
12
SET
OSD
ON
OFF
OSD
f
ACMS
Pr-12
P
SET
R
P
SET
R
PR CH MFT STATION
01 00 PR-03
CHANNEL/CABLE : AV
C03
i
P
SET
R
02 C02 00 PR-02
03 C04 00 PR-04
04 - - - - - - - - -
05 C03 00 PR-03
06 - - - - - - - - -
07 - - - - - - - - -
08 - - - - - - - - -
01 C01 00 PR-01
P
SET
R
OK
i
,DELETE :
MOVE :
02 C02 00 PR-04
03 - - - - - - - - -
04 C03 00 PR-03
05
06 - - - - - - - - -
- - - - - - - - -
07 - - - - - - - - -
08 - - - - - - - - -
01 C01 00 PR-02
P
SET
R
OK
i
,DELETE :
MOVE :
02 C02 00 PR-02
03 C04 00 PR-04
04 - - - - - - - - -
05 C03 00 PR-03
06 - - - - - - - - -
07 - - - - - - - - -
08 - - - - - - - - -
01 C01 00 PR-01
P
SET
R
OK
i
,DELETE :
MOVE :
Preparation
17
Displaying Disc Information
on-screen
You can display various information about the disc
loaded on-screen.
1. Press DISPLAY to show various playback
information.
The items displayed differ depending on the disc
type or playing status.
2. You can select an item by pressing v / V and
change or select the setting by pressing b / B.
Title (Track) – Current title (or track) number/total
number of titles (or tracks)
Chapter – Current chapter number/total number of
chapters
Time – Elapsed playing time
Audio – Selected audio language or channel
Subtitle – Selected subtitle
Angle – Selected angle/total number of angles
Sound – Selected sound mode
Note:
If no button is pressed for a few seconds, the on-screen
display disappears.
Initial Settings
By using the DVD Setup menu, you can make various
adjustments to items such as picture and sound.You
can also set a language for the subtitles and the Setup
menu, among other things. For details on each Setup
menu item, see pages 17 to 20.
To display and exit the Menu:
Press SETUP to display the menu. A second press of
SETUP will take you back to initial screen.
To go to the next level:
Press B on the remote control.
To go back to the previous level:
Press b on the remote control.
General Operation
1. Press DVD on the remote control.
2. Press SETUP.
The Setup menu appears.
3. Use v / V to select the desired option then press B
to move to the second level.
The screen shows the current setting for the
selected item, as well as alternate setting(s).
4. Use v / V to select the second desired option then
press B to move to the third level.
5. Use v / V to select the desired setting then press
ENTER/OK to confirm your selection.
Some items require additional steps.
6. Press SETUP or
NN
exit the Setup menu.
Before Operation-DVD part
1 / 12
1 / 3
0:20:09
ABC
1 ENG
1 / 1
3D SUR
Menu Language
Original
English
Off
Original
Disc Audio
Disc Subtitle
Disc Menu
Move
Select
LANGUAGE
18
Before Operation-DVD part
LANGUAGE
Menu Language
Select a language for the VCR and DVD’s setup menu
and information display.
Disc Audio / Subtitle / Menu
Select the language you prefer for the audio track
(disc audio), subtitles, and the disc menu.
Original: Refers to the original language in which the
disc was recorded.
Other:To select another language, press number
buttons then ENTER/OK to enter the corresponding
4-digit number according to the language code list in
the reference chapter (see page 35). If you enter the
wrong language code, press CLEAR.
DISPLAY
TV Aspect
4:3 :
Select when a standard 4:3 TV is connected.
16:9 : Select when a 16:9 wide TV is connected.
Display Mode
Display Mode setting works only when the TV Aspect
mode is set to “4:3”.
Letterbox: Displays a wide picture with bands on the
upper and lower portions of the screen.
Panscan:
Automatically displays the wide picture on the
entire screen and cuts off the portions that do not fit.
TV Output Select
Set this unit TV Output Select options according to the
TV connection type.
YPbPr: When your TV is connected with the
COMPONENT/PROGRESSIVE SCAN VIDEO OUT
jacks on this unit.
RGB: When your TV is connected with the SCART
(RGB signal) jack.
DVD
DVD
DVD
Menu Language
Original
English
Off
Original
Disc Audio
Disc Subtitle
Disc Menu
Move
Select
LANGUAGE
DISPLAY
TV Aspect
Widescreen
16 : 9
Display Mode
Move
Select
TV Output Select RGB
Preparation
19
Before Operation-DVD part
AUDIO
Each DVD disc has a variety of audio output options.
Set this unit’s AUDIO options according to the type of
audio system you use.
Dolby Digital / DTS / MPEG
Bitstream: Select “Bitstream” if you connect the
DVD+VCR’s DIGITAL AUDIO OUT jack to an amplifi-
er or other equipment with a Dolby Digital, DTS or
MPEG decoder.
PCM (for Dolby Digital / MPEG): Select when con-
nected to a two-channel digital stereo amplifier.
DVDs encoded in Dolby Digital or MPEG will be
automatically downmixed to two-channel PCM audio.
Off (for DTS): If you select “Off”, the DTS signal is
not output through the DIGITAL AUDIO OUT jack.
Sample Freq. (Frequency)
If your receiver or amplifier is NOT capable of handling
96 kHz signals, select 48 kHz.When this choice is
made, this unit automatically converts any 96 kHz sig-
nals to 48 kHz so your system can decode them.
If your receiver or amplifier is capable of handling 96
kHz signals, select 96 kHz.When this choice is made,
this unit passes each type of signal through without any
further processing.
Check the documentation for your amplifier to verify its
capabilities.
DRC (Dynamic Range Control)
With the DVD format, you can hear a program’s sound-
track in the most accurate and realistic presentation
possible, thanks to digital audio technology. However,
you may wish to compress the dynamic range of the
audio output (the difference between the loudest sounds
and the quietest ones).This allows you to listen to a
movie at a lower volume without losing clarity of sound.
Set DRC to On for this effect.
Vocal
Set to On only when a multi-channel karaoke DVD is
playing.The karaoke channels on the disc mix into nor-
mal stereo sound.
LOCK (Parental Control)
Rating
Blocks playback of rated DVDs based on their content.
Not all discs are rated.
1. Select “Rating” on the LOCK menu then press B.
2. To access the LOCK options, you must input the
password you have created. If you have not yet
entered password, you are prompted to do so.
Input a password and press ENTER/OK. Enter it
again and press ENTER/OK to verify. If you make a
mistake before pressing ENTER/OK, press CLEAR.
3. Select a rating from 1 to 8 using the v / V buttons.
Rating 1-8: Rating one (1) has the most restrictions
and rating eight (8) is the least restrictive.
Unlock: If you select unlock, parental control is not
active and the disc plays in full.
4. Press ENTER/OK to confirm your rating selection,
then press SETUP to exit the menu.
Password
You can enter or change password.
1. Select Password on the LOCK menu then press B.
2. Follow step 2 as shown above (Rating).
To change the password, press ENTER/OK when the
“Change” option is highlighted. Input a password and
press ENTER/OK. Enter it again and press
ENTER/OK to verify.
3. Press SETUP to exit the menu.
If you forget your password
If you forget your password, you can clear it using the
following steps:
1. Press SETUP to display the Setup menu.
2. Input the 6-digit number “210499” and press
ENTER/OK.The password is cleared.
DVD
DVD
DVD
DivXDVD
Dolby Digital
Bitstream
PCM
48KHz
On
Bitstream
DTS
MPEG
Sample Freq.
DRC
OnVocal
Move
Select
AUDIO
LOCK
Rating
New
Unlock
Password
Area Code
Move
Select
GB
20
Before Operation - DVD part
Area Code
Enter the Area Code whose standards were used to
rate the DVD video disc, based on the list in the
reference chapter (see page 35).
1. Select “Area Code” on the LOCK menu then press
B.
2. Follow step 2 as shown left (Rating).
3. Select the first character using v / V buttons.
4. Press B and select the second character using
v / V buttons.
5. Press ENTER/OK to confirm your area code
selection.
OTHERS
The PBC and Auto Play and Divx(R) settings can be
changed.
PBC
Set Playback Control (PBC) to On or Off.
On:Video CDs with PBC are played according to the
PBC.
Off:Video CDs with PBC are played the same way as
Audio CDs.
Auto Play
You can set up the DVD+VCR so a DVD disc automati-
cally starts playing whenever the DVD is inserted.
If Auto Play mode is set to On, this DVD player will
search for title that has the longest playback time and
then play back the title automatically.
Note:
The Auto Play function may not work for some DVDs.
DivX(R) VOD
We provide you the DivX
®
VOD (Video On Demand)
registration code that allows you to rent and purchase
videos using the DivX
®
VOD service. For more informa-
tion, visit www.divx.com/vod.
1. Select “DivX(R) VOD” option then press B.
2. Press ENTER/OK while “Select” is selected and the
registration code will appear.
Use the registration code to purchase or rent the
videos from DivX
®
VOD service at
www.divx.com/vod. Follow the instructions and
download the video onto a disc for playback on this
unit.
3. Press ENTER/OK to exit.
Note:
All the downloaded videos from DivX
®
VOD can only be
played back on this unit.
.
DVD
VCD
DVD
PBC
Off
Move
Auto Play
OTHERS
On
Select
SelectDivX(R) VOD
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
