Tunturi CE35 User manual

Page is loading ...

2

OWNER'S MANUAL

•

CF35

IMPORTANT SAFETY

INSTRUCTIONS

Read this guide through carefully

before assembling, using or servicing

your fitness equipment. Please keep

the guide somewhere safe; it will

provide you now and in the future with

the information you need to use and

maintain your equipment. Always follow

these instructions with care.

YOUR HEALTH

•

Before you start any training, consult a

physician to check your state of health.

•

If you experience nausea, dizziness

or other abnormal symptoms while

exercising, stop your workout at once

and consult a physician.

•

To avoid muscular pain and strain,

begin each workout by warming up and

end it by cooling down (slow pedaling at

low resistance). Don’t forget to stretch at

the end of the workout.

EXERCISING

ENVIRONMENT

•

The equipment is not to be used

outdoors.

•

Place the equipment on a firm, level

surface. Place the equipment on a

protective base to avoid any damages to

the floor beneath the equipment.

•

Make sure that the exercising

environment has adequate ventilation.

To avoid catching cold, do not exercise

in a draughty place.

•

In training, the equipment tolerates

an environment measuring +10°C to

+35°C. The equipment can be stored

in temperatures ranging between

-15°C and +40°C. Air humidity in the

training or storage environment must

never exceed 90 %.

USING THE EQUIPMENT

•

If children are allowed to use the

equipment, they should be supervised

and taught to use the equipment

properly, keeping in mind the child’s

physical and mental development and

their personality.

•

Before you start using the equipment,

make sure that it functions correctly

in every way. Do not use a faulty

equipment.

•

Press the keys with the tip of the

finger; your nails may damage the key

membrane.

•

Never lean on the interface.

•

Never remove the side covers. Do not

step on the frame casing.

•

Only one person may use the

equipment at a time.

•

Hold the stationary handlebar for

support when getting on or off the

equipment.

•

Wear appropriate clothing and shoes

when exercising.

•

Protect the meter from sunlight and

always dry the surface of the meter if

there are any drops of sweat on it.

•

Further information on warranty terms

can be found in the warranty booklet

included with the product.

•

Please note that the warranty does

not cover damage due to shipping

or negligence of adjustment or

maintenance instructions described in

this manual.

CONTENTS

IMPORTANT SAFETY INSTRUCTIONS ....................2

ASSEMBLY ..............................................................52

EXERCISING .............................................................4

CONSOLE ..................................................................5

MAINTENANCE .........................................................7

TRANSPORT AND STORAGE...................................7

TECHNICAL SPECIFICATIONS .................................8

GB

3

OWNER'S MANUAL

•

CF35

•

The equipment must not be used by

persons weighing over 150 kg.

•

Make sure the equipment is

unplugged before carrying out any

assembly or maintenance procedures.

•

Do not attempt any servicing or

adjustments other than those described

in this guide. Everything else must

be left to someone familiar with the

maintenance of electromechanical

equipment and authorized under the

laws of the country in question to carry

out maintenance and repair work.

•

This product must be grounded. If

it should malfunction or breakdown,

grounding provides a path of least

resistance for electric current to reduce

the risk of electric shock. This product

is equipped with a cord having an

equipment-grounding conductor and

a grounding plug. The plug must be

plugged into an appropriate outlet that

is properly installed and grounded in

accordance with all local codes and

ordinances.

DANGER:

Improper connection of the equipment-

grounding conductor can result in a

risk of electric shock. Check with a

qualified electrician or technician if you

are in doubt as to whether the product

is properly grounded. Do not modify the

plug provided with the product - if it will

not fit the outlet, have a proper outlet

installed by a qualified electrician.

SAVE THIS INSTRUCTION MANUAL

NOTE ABOUT SAFETY

FOR UNITS WITH

ELECTRICAL POWER

Before connecting the equipment to a

power source, make sure that the local

voltage matches that indicated on the

type plate: the equipment operates at

either 230 v or 115 v (north american

version). Note! The equipment must be

connected to a grounded wall socket.

Do not use extension wires when

connecting the equipment to the power

source. Always switch off the power and

unplug the equipment from the electrical

outlet immediately after using!

To reduce the risk of burns, fire, electric

shock or injury to persons:

1. The equipment should never

be left unattended when plugged in.

Unplug the equipment from the outlet

when not in use, before carrying out any

maintenance or repair procedures, and

before moving the unit.

2. Do not operate the equipment

under a blanket or other combustive

material. Excessive heating can occur

and cause fire, electric shock or injury to

persons.

3. Do not connect the equipment

to a power source, or operate the

equipment if there is any sort of damage

to the power cord or the unit itself.

4. Do not connect the equipment

to a power source or operate the

equipment outdoors or in damp

locations.

5. Keep the power cord away from

hot objects.

6. Do not route the power cord

beneath a carper or place any objects

on the cord. Also make sure that the

power cord does not run underneath the

equipment.

7. Do not alter (for example

lengthen) the cord between the

transformer and the unit.

NOTE ABOUT

ASSEMBLING THE

EQUIPMENT

Start by unpacking the equipment. The

detailed assembly instructions can be

found at the back of this guide. Follow

the instructions in given order.

Before assembly, check the contents of

the package. If a part is missing, please

contact your dealer with the model,

equipment serial no. and spare part no.

of the missing part. You’ll find a spare

part list at the back of this guide. The

4

OWNER'S MANUAL

•

CF35

hardware kit contents are marked with

* in the spare parts list. The directions

left, right, front and back are defined as

seen from the exercising position. Keep

the assembly tools, as you may need

them e.g. for adjusting the equipment.

Note that two people are needed for the

assembly.

The packaging includes a silicate bag for

absorbing moisture during storage and

transportation. Please dispose of the bag

once you have unpacked the equipment.

Allow at least 100 cm of clearance

around the equipment. We also

recommend opening the package and

assembling the product on a protective

base.

WELCOME TO THE WORLD OF

TUNTURI EXERCISING!

Your choice shows that you really want to invest in

your well being and condition; it also shows you

really value high quality and style. With Tunturi

Fitness Equipment, you’ve chosen a high quality,

safe and motivating product as your training

partner. Whatever your goal in training, we are

certain this is the training equipment to get you

there. You’ll find information about using your

exercise equipment and what makes for efficient

training at Tunturi’s website at WWW.TUNTURI.

COM.

EXERCISING

Working out using an elliptical trainer is excellent

aerobic exercise, the principle being that the

exercise should be suitably light, but of long

duration. Aerobic exercise is based on improving

the body ‘s maximum oxygen uptake, which in turn

improves endurance and fi tness. The ability of the

body to burn fat as a fuel is directly dependent on

its oxygen-uptake capacity. Aerobic exercise should

above all be pleasant. You should perspire, but you

should not get out of breath during the workout.

You must, for example, be able to speak and not just

pant while pedaling.

You should exercise at least three times a week,

30 minutes at a time, to reach a basic fi tness level.

Maintaining this level requires a few exercise

sessions each week. Once the basic condition

has been reached, it is easily improved simply by

increasing the number of exercise sessions. Exercise

is always rewarding for weight loss, because it is

the only way of increasing the energy spent by the

body. This is why it is always worthwhile to combine

regular exercise with a healthy diet. A dieter should

exercise daily, at fi rst 30 minutes or less at a time,

gradually increasing the daily workout time to one

hour.

You should start slowly at a low pedaling speed

and low resistance, because for an overweight

person strenuous exercise may subject the heart

and circulatory system to excessive strain. As

fitness improves, resistance and pedaling speed

can be increased gradually. Exercise efficiency can

be measured by monitoring the pulse. The pulse

meter helps you monitor your pulse easily during

exercise, and thus to ensure that the exercise is

sufficiently effective but not over-strenuous. Start

your workout with slow tempo and low resistance.

Gradually increase tempo and resistance according

to your own condition. Keep your head up and neck

long in order to avoid stress on your neck, shoulders

and back. Keep also your back straight. Make sure

that your feet are centered on the foot pedals and

that your hips, knees, ankles and toes are facing

forward. Keep your body weight centered over your

lower body regardless of whether you lean forward

or stand upright. Stop your workout by gradually

decreasing tempo and resistance.

Don’t forget to stretch afterwards. To strengthen

cardiovascular system, maintain low resistance but

high tempo. Exercising with higher resistance and

slow tempo strengthens correspondingly your back

and hips.

HEART RATE

No matter what your goal, you’ll get the best results

by training at the right level of effort, and the best

measure is your own heart rate.

The CF35 meter has a heart rate receiver compatible

with Polar equipment, so you can also use Polar

uncoded heart rate transmitter belts for heart rate

measurement.

NOTE! If you are fitted with a pacemaker, please

consult a physician before using a heart rate

transmitter belt.

The most reliable heart rate measurement is

achieved with a telemetric device, in which the

electrodes of the transmitter fastened to the chest

transmit the pulses from the heart to the console

by means of an electromagnetic field. If you want

to measure your heart rate this way during your

workout, moisten the grooved electrodes on the

transmitter belt with saliva or water. Fasten the

transmitter just below the chest with the elastic

belt, firmly enough so that the electrodes remain

in contact with the skin while exercising, but not so

tight that normal breathing is prevented. If you wear

the transmitter and belt over a light shirt, moisten

the shirt slightly at the points where the electrodes

touch the shirt. The transmitter automatically

transmits the heart rate reading to the console up to

a distance of about 1 m.

If the electrode surfaces are not moist, the heart-

GB

5

OWNER'S MANUAL

•

CF35

rate reading will not appear on the display. If the

electrodes are dry, they must be moistened again.

Allow the electrodes warm up properly to ensure

accurate heart rate measurement. If there are several

telemetric heart rate measurement devices next to

each other, the distance between them should be at

least 1.5 m. Similarly, if there is only one receiver and

several transmitters in use, only one person with a

transmitter should be within transmission range. the

transmitter is switched to an active state only when

it is being used for measurement. sweat and other

moisture can, however, keep the transmitter in an

active state and waste battery energy. therefore it is

important to dry the electrodes carefully after use.

When selecting training attire, please note

that some fibers used in clothes (e.g. polyester,

polyamide) create static electricity, which may

prevent reliable heart rate measurement. Please

note that a mobile phone, television and other

electrical appliances form an electromagnetic field

around them, which will cause problems in heart

rate measurement.

HAND GRIP PULSE MEASUREMENT

(HGP-VERSION)

Pulse is measured by sensors in the handlebars.

Pulse is measured when the user of CF35 is touching

both sensors simultaneously. Reliable pulse

measurement requires that the skin is constantly

touching the sensors and that the skin is slightly

moist. Too dry or too moist skin weakens the

reliability of hand pulse measurement.

HEART RATE IN TRAINING

First find your maximum heart rate i.e. where the

rate doesn’t increase with added effort. If you don’t

know your maximum heart rate, please use the

following formula as a guide:

220 - AGE

The formula gives an average value, the maximum

varies from person to person. The maximum heart-

rate diminishes on average by one point per year. If

you belong to a risk group, ask a doctor to measure

your maximum heart rate for you.

We have defined three different heart-rate zones to

help you with targeted training.

BEGINNER

•

50-60 % of maximum heart-rate

Also suitable for weight-watchers, convalescents

and those who haven’t exercised for a long

TIME.

Three sessions a week of at least a half-hour each

is recommended. Regular exercise considerably

improves beginners’ respiratory and circulatory

performance and you will quickly feel your

improvement.

TRAINER

•

60-70 % of maximum heart-rate

Perfect for improving and maintaining fitness. Even

reasonable effort develops the heart and lungs

effectively, training for a minimum of 30 minutes at

least three TIMEs a week. To improve your condition

still further, increase either frequency or effort, but

not both at the same time!

ACTIVE TRAINER

•

70-80 % of maximum heart-

rate

Exercise at this level suits only the fittest and

presupposes long-endurance workouts.

CONSOLE

BUTTONS

1. SELECTION DIAL

The selection dial functions in two ways:

A) Rotating the dial (+ / -). By rotating the dial

clockwise, you can scroll the menus to the right, and

increase values or resistance. By rotating the dial

counter-clockwise, you can scroll the menus to the

left, and decrease values or resistance.

B) Pressing the dial (ENTER). By pressing the dial, you

can accept the selection you made when rotating

the dial.

2. START/STOP

Starts, pauses, and stops training. During training,

pressing this button once activates the pause mode.

Pressing the button again starts the program again.

3. RESET

Single push: return to the program menu. Long

push: restarts the meter.

4. RECOVERY

Calculates your recovery heart rate index.

5. BODY FAT

Calculates your body mass index (BMI) and shows

your body fat %.

6

OWNER'S MANUAL

•

CF35

DISPLAY

Time (mm:ss), speed (km/h or ml/h), RPM

(revolutions per min), distance (km or ml), energy

consumption (kcal), power(W) and heart rate (bpm)

are displayed.

PROGRAMS

1.MANUAL PROGRAM

Set target time and/or distance and/or energy

consumption and/or upper heart rate limit by using

the SELECTION DIAL.

Start training by pressing START/STOP button.

If you have set target/targets, the target/targets start

to count down. Adjust resistance with SELECTION

DIAL.

2. PRESET PROGRAMS

Preset program profile is shown for two seconds

while programs are browsed. Select desired preset

program by using the SELECTION DIAL.

Set time for training and/or target distance and/or

energy and/or upper heart rate limit by SELECTION

DIAL.

Start training by pressing START/STOP button.

If you have set target/targets, the target/targets

start to count down. During training you can scale

the load by SELECTION DIAL.

3. USER PROGRAM

The program profile used last time is displayed.

You can either start training with your personal

memorized training targets by pressing START/

STOP or modify the program. The program profile

bar (1/20) that can now be modified blinks. If

you want to change, modify the blinking bar and

confirm. Next bar will blink. After the last bar, the

display switches back to the first bar. By pressing

the ENTER button for 2 seconds you can finish the

profile modifying. Now program is ready with your

memorized personal training data (time, distance,

energy targets and heart rate limit). Modify your

targets if needed. Start training by pressing START/

STOP button.

If you have set target/targets, the target/targets

start to count down. During training you can scale

the load by SELECTION DIAL

4. HEART RATE CONTROL (H.R.C.)

Select between four different training intensities

(55%, 75%, 90% or TARGET). By selecting TARGET

you can insert target heart rate.

Start training by pressing START/STOP button.

During the training the equipment will

automatically adjust the resistance so that your

target will be reached and maintained.

5. CONSTANT WATT )

Set target power in watts and target time and/or

distance and/or energy consumption and/or upper

heart rate limit by SELECTION DIAL.

Start training by pressing START/STOP button.

If you have set target/targets, the target/targets

start to count down. During training the equipment

will adjust resistance dependently on your pedaling

speed, so that target power level is achieved and

maintained. You can change the target power by

SELECTION DIAL.

6. RECOVERY

Start the recovery calculation after training by

pressing RECOVERY button. Recovey heart rate

calculation can be started only if the heart rate

measurement is activated and the heart rate value

is shown on the display The measurement takes 60

seconds. After 60 seconds, the display shows your

recovery index F1-F6 (F1 = best result). To get back

to main menu, press RECOVERY button once again.

7. BODY FAT

Press BODY FAT button to start measurement. Hold

both hands on the handgrips and wait for 8 seconds.

The meter will show body fat advice symbol, body

fat % and BMI for 30 seconds.

SETTING USER DATA

Right after restarting the meter or reset (long

push) you can enter to the user menu. Select the

user and confirm. Set your sex, age, height and

weight. Confirm by selection dial. Personal exercise

target data (time, distance, energy, heart rate limit)

will be memorized and recalled as defaults every

time when the user is selected. If you modify your

personal training data, it will automatically be

memorized.

ADDITIONAL NOTES

1. For speed and distance you can choose either

metric or English units by using the KM/ML switch

located on the back cover of the meter. The power

cord has to be unplugged and replugged to apply

the change.

2. If you are not training and buttons are not

pressed, the meter switches into the Sleep mode

after about four minutes. Room temperature is

displayed.

3. Training is paused for a maximum of 4 minutes

by pressing the START/STOP button. Pressing the

button again allows you to continue the paused

training session using the previous training data.

4. Entering training targets (time, distance, energy,

heart rate limit) is possible only in the STOP mode

(not during training).

5. If you don’t want to change your user data every

time you start training, press START/STOP to skip

user data editing. You’ll enter to the training in

Manual mode.

6. This equipment cannot be used for therapeutic

purposes.

7. Energy consumption is calculated based on

average values. The energy expenditure is displayed

in kilocalories. To convert this into joules, use the

formula: 1 Kcal = 4.187 KJ.

8. If you are training with heart rate measurement

(either chest belt or handgrip heart rate) you can set

maximum heart rate limit. When limit is exceeded

GB

7

OWNER'S MANUAL

•

CF35

while training meter will give alarm beeps.

9. Preset programs are divided into 16 steps.

Duration of the one step depends on the time set

for the whole training. If time is not set, duration of

one step will be 100 m in distance.

10. If you have set targets to count down, a signal

sounds and training automatically stops when any

of target reaches zero. You can restart training by

pressing START/STOP

11. Note that recovery index is in relation to the

heart rate frequency in both the beginning and the

end of the measurement.

12. In H.R.C program heart rate target ranges (55%,

75% and 90%) are calculated as percent from your

age predicted maximum heart rate (calculation

formula: maximum heart rate = 220 – age).

13. Automatic adjustment of the resistance during

H.R.C program occurs upwards every 30 seconds

and downwards every 15 seconds, if needed.

14. BODY FAT is a personal measurement and the

result is based on average european population

values.

B.M.I. (Body Mass Index) table:

LOW < 20

LOW / MEDIUM 20 – 24

MEDIUM 24 - 26,5

MEDIUM / HIGH > 26,5

Formula for BMI = weight (kg) / height^2 (m)

BODY FAT % (average european population) table:

Male:

LOW < 13

LOW / MEDIUM 13 – 26

MEDIUM 26 – 30

MEDIUM / HIGH > 30

Female:

LOW < 23

LOW / MEDIUM 23 – 36

MEDIUM 36 – 40

MEDIUM / HIGH > 40

MAINTENANCE

The equipment requires very little maintenance.

Check, however, from time-to-time that all screws

and nuts are tight.

•

After exercising, clean the equipment with a soft,

absorbent cloth. Do not use solvents.

•

Never remove the equipment’s protective casing.

•

The electromagnetic brake forms a magnetic field

that may damage the mechanism of a watch, or the

magnetic identification strip on a credit or cash card,

should they come into immediate contact with the

magnets. Never attempt to detach or remove the

electromagnetic brake!

•

The electromagnetic brake is based on

electromagnetic resistance; resistance level is

electronically measured and shown as watt reading

on the display. Due to the measurement system,

your Tunturi crosstrainer need not be re-calibrated

when assembled, serviced and used according to

this Owner’s Manual.

MALFUNCTIONS

Despite continuous quality control, defects and

malfunctions caused by individual components

may occur in the equipment. In most cases it’s

unnecessary to take the whole device in for repair,

as it’s usually sufficient to replace the defective part.

If the equipment does not function properly during

use, contact your Tunturi dealer immediately.

Always give the model and serial number of your

equipment. Please state also the nature of the

problem, conditions of use and purchase date.

If you require spare parts, always give the model,

serial number of your equipment and the spare part

number for the part you need. The spare part list

is at the back of this manual. Use only spare parts

mentioned in the spare part list.

TRANSPORT AND STORAGE

Please follow these instructions when carrying

and moving the equipment about, because lifting

it incorrectly may strain your back or risk other

accidents:

Always switch the power off and unplug the power

cord before you start moving the equipment

around!

For transportation or moving of the device, two

grown-ups are needed. Remain standing in front of

the device on each side and take a sturdy grip at the

handles. Lift the front of the device so as to lift the

rear of the device on the wheels. Move the device

and carefully put it down to its new place.

NOTE! Transport the equipment with caution over

uneven surfaces, for example over a step. The

equipment should never be transported upstairs

using the wheels over the steps, instead it must be

carried. We recommend that you use a protective

base when transporting the equipment.

To prevent the equipment malfunctioning, store in

a dry place with as little temperature variation as

possible and protected from dust.

8

OWNER'S MANUAL

•

CF35

TECHNICAL SPECIFICATIONS

Length .................................................183 cm

Width ...................................................70 cm

Height ..................................................170 cm

Weight .................................................69 kg

The Tunturi CF35 meets the requirements of the EU’s

EMC Directives on electromagnetic compatibility

(89/336/EEC) and electrical equipment designed for

use within certain voltage limits (73/23/EEC). This

product therefore carries the CE label.

The Tunturi model CF35 meets EN precision and

safety standards (Class A, EN-957, parts 1 and 9)

for fitness devices. The precision of the capacity

measurement is secured during manufacturing

by adjusting the brake with a dynamometer.

Calculation of exercise capacity is based on rotation

speed and moment.

Due to our continuous policy of product

development, Tunturi reserves the right to change

specifications without notice.

NOTE! The instructions must be followed carefully

in the assembly, use and maintenance of your

equipment. The warranty does not cover damage

due to negligence of the assembly, adjustment and

maintenance instructions described herein. Changes

or modifications not expressly approved by Tunturi

Oy Ltd will void the user’s authority to operate the

equipment!

WE WISH YOU MANY ENJOYABLE TRAININGS WITH

YOUR NEW TUNTURI TRAINING PARTNER!

Page is loading ...

CF35

52

4X

M8X16X1.2

M8

M8X15

A

CX4

FX4

HX8

AX4

M8*15mm ALLEN HEAD SCREW(16)

NO.1-9

NO.1-19

NO.1-27

M8*20mm ALLEN HEAD SCREW(6)

FX2

GX2

NO.1-12

NO.1-16

NO.1-21

NO.1-30 M8*42mm ALLEN HEAD SCREW(2)

I

NO.1-33 M6*10mm SCREW(1)

J

BX4

CX4

EX2

FX6

GX4

NO.1-6

NO.1-10

NO.1-13

NO.1-2

NO.1-17

NO.1-22

NO.1-28

M8 SPRINGWASHER(34)

AX4

CX4

FX4

GX2

NO.1-11

NO.1-3

NO.1-20

NO.1-24

NO.1-29

M8*1.2mm WASHER(22)

EX2

F

GX2

NO.1-14

NO.1-23

NO.1-18 M8*2.0*28 mm WASHER(2)

M8*2.0*38 mm WASHER(4)

EX2

G

NO.1-1

HX8

NO.1-25 16.5*21.7*0.25T BILLOW WASHER(2)

NO.1-15

E

M5*15mm SCREW(2)

IX2

NO.1-31

M8 WASHER CURVE(10)

IX2

NO.1-8

B

M5*30 SCREW(2)

TOOL(1)

M8*25mm ALLEN HEAD SCREW(2)

G

NO.1-26

NO.1-34 M6*15mm SCREW(2)

J

BX8

NO.1-32

NO.1-5

B

NO.1-4 M8*56mm ALLEN HEAD SCREW(4)

M8*58mm ALLEN HEAD SCREW(4)

NO.1-7 NYLOC NUT M8(4)

B

NO.1-35 M6 SPRINGWASHER(2)

J

C

2X

4X

M8X56

B

M5X30

8X

M8X16X1.2

4X

M8

4X

M8X58

M8X16X1.2

M8

A

4X

M8

D

Page is loading ...

57

CF35

NR. CODE DESCRIPTION QTY.

1 103 2038 BASE FRAME 1

2 103 9040 UPRIGHT TUBE 1

3 203 9025 UPPER SWIVEL HANDLE BAR L 1

4 203 9026 UPPER SWIVEL HANDLE BAR  R  1

5 203 9027 LOWER SWIVEL HANDLE BAR L 1

6 203 9028 LOWER SWIVEL HANDLE BAR R 1

7 103 9041 PEDAL TUBE L 1

8 103 9042 PEDAL TUBE  R  1

9 103 9043 OUTER PEDAL POST, LEFT 1

10 103 9044 OUTER PEDAL POST, RIGHT 1

11 103 9045 FRONT FOOT 1

12 103 9046 MIDDLE FOOT 1

13 103 9047 REAR FOOT 1

14 103 9048 CROSS FRAME 2

15 104 9045 RAIL 2

16 303 1055 AXLE FOR PULLEY 1

17 303 1056 AXLE SUPPORT 1

18 104 9046 PEDAL TUBE SHAFT 2

19 104 9047 BUSHING 4

20 503 9022 CURVE BRACKET 1

21 653 7072 BRACKET FOR PEDAL 2

22 203 4096 FIX HANDLEBAR 1

23 M5*20MM SCREW 16

24 M8*52MM HEX HEAD BOLT 1

25 M6*53MM SCREW 1

26 M5*10MM SCREW 8

27 M6*10MM SCREW 3

28 M8*15MM ALLEN HEAD SCREW 24

29 M8*20MM ALLEN HEAD SCREW 12

30 M8*42MM ALLEN HEAD SCREW 2

31 M8*58MM ALLEN HEAD SCREW 4

32 M8*63MM ALLEN HEAD SCREW 2

33 M8 NYLOC NUT 1

34 M6*18MM HEX HEAD BOLT 4

35 M5*1,5MM WASHER 8

36 M6*1,2MM WASHER 2

37 M8*1,2MM WASHER 38

38 M8*28MM WASHER 2

39 M8*38MM WASHER 4

40 303 1031 BUSHING TUBE 2

41 503 9026 BRACKET FOR MAGNET BOW 1

42 M8 SPRING WASHER 42

43 M6*1,2MM WASHER 2

44 M8 WASHER CURVE 2

45 M10 WH NUT 2

46 M6 NYLOCK NUT 4

47 M6 NYLOCK NUT 1

48 M8 NYLOCK NUT 2

49 653 7073 CLIP C17 3

50 523 4072 BEARING 4

51 523 4073 BEARING 6

52 303 1032 PLUG AXLE SUPPORT 6

53 303 1033 PLUG AXLE SUPPORT34 4

54 303 1034 PLUG AXLE SUPPORT30 4

55 104 9048 BUSHING 8

56 213 1040 OVAL END CAP 1

57 503 7037 SPRING BRACKET 1

58 213 1026 REAR FOOT COVER 2

59 213 1027 END CAP FOR FIX HANDLEBAR 2

60 523 4074 ROLLER 2

61 533 9066 ADJUST FEET 6

62 213 1037 20 TURNING PEDAL 2

63 443 4072 BELT 1

64 213 1028 END CAP FOR HANDLEBAR 2

65 173 9056 TOP SLEEVE 1

66 173 9080 CHAIN COVER L 1

67 173 9081 CHAIN COVER R 1

68 173 9059 SCREW COVER 2

69 173 9060 FRONT FOOT COVER 1

70 173 9061 MIDDLE FOOT COVER 1

71 173 9082 RAIL COVER 1

72 M6*15MM SCREW 1

73 403 1209 UPPER COMPUTER CABLE 1

74 643 2014 SPRING 1

75 403 1210 WIRE ROD 1

76 363 1025 PEDAL 2

77 303 1040 20 PULLEY 1

78 213 1029 TURNING PLATF COVER 2

79 503 4103 METER ADJ. BRACKET 1

80 503 4104 METER BRACKET 1

81 503 4105 ADAPTOR SOCKET 1

82 213 1041 FIX HANDLEBAR FOAM GRIPS 2

83 213 1031 HANDLEBAR FOAM GRIPS 2

84 533 4160 MOVING WHEEL 2

85 M5*15MM SCREW 2

86 M5*15MM SCREW 4

87 653 7074 WAVE WASHER 2

88 403 1211 SERVO MOTOR 1

89 M6*10MM SCREW 4

90 403 1198 HAND PULSE SET 2

91 403 4215 20 HAND PULSE WIRE 1

92 503 4106 SENSOR BRACKET 1

93 235 1070 CONSOLE 1

94 403 9045 MAGNET 1

95 M6*12MM SCREW 1

96 ADAPTOR 1

403 0062EU

403 0062US

403 0062UK

403 0062AUS

97 556 0002 TOOL 1

98 556 0004 TOOL 1

99 556 0005 TOOL 1

100 M3*15MM SCREW 2

101 M5*12MM SCREW 4

102 M5*20MM SCREW 2

103 M5*20MM SCREW 2

104 M6*1,2MM WASHER 1

105 556 0006 TOOL 1

106 556 0007 TOOL 1

105 403 1212 SENSOR WIRE 1

106 403 1213 DC CABLE 1

107 M6*1,5MM WASHER 3

108 103 9069 SPACER SLEEVE 3

109 M6*14MM M6*14MM HEX HEAD BOLT 3

110 503 9026 IDLE BRACKET 1

111 643 7009 SPRING 1

112 103 1091 20 MAGNET HOLDER 1

113 303 1053 20 FLYWHEEL 1

114 303 1054 20 FLYWHEEL AXLE 1

115 653 7077 20 CLIP C12 2

116 M10*2MM WASHER 2

117 3/8” 3/8” WH NUT 2

 583 9041 OWNER’S MANUAL 1

Page is loading ...

www.tunturi.com

Austria

Accell Fitness Österreich

Am Messendorfgrund 30

A-8042 Graz

Österreich

Tel: +43 316 716412

Fax: +43 316 716435

Benelux

Accell Fitness Benelux

Koningsbeltweg 51

1329 AE ALMERE

The Netherlands

Tel: +31 36 5460050

Fax: + 31 36 5460055

Finland

Accell Fitness Scandinavia

Varusmestarintie 26

20361 TURKU

Finland

Tel: +358 2513 31

Fax: +358 2513 313

Germany

Accell Fitness Deutschland

P/a Koningsbeltweg 51

1329 AE ALMERE

The Netherlands

Tel: +31 36 5460050

Fax: + 31 36 5460055

United Kingdom

Accell Fitness United Kingdom

Bolton House

Nottingham South Industrial Estate

Ruddington Lane

Wilford

Nottingham NG11 7EP

United Kingdom

Tel: +44 115 9822844

Fax: +44 115 9817784

Sweden

Accell Fitness Scandinavia

Varusmestarintie 26

20361 TURKU

Finland

Tel: +358 2513 31

Fax: +358 2513 313

Switzerland

Accell Fitness Schweiz

Altgraben 31

CH-4624 Härlungen SD

Schweiz

Tel: +41 (0)62-3877979

Fax: +41 (0)62-3877970

USA / Canada

Accell Fitness North America Inc.

130 Hayward Ave, Suite 2

N2C 2E4

Kitchener, ON Canada

Tel. 1-888-388-6887

Fax: 1-519-576-2521

www.accellﬁ tness.com

583 4050

583 9016

Tunturi CE35 User manual

This manual is also suitable for

Tunturi CE35 User manual

in other languages

Related papers

Other documents