WFT8300
WFT7300
P/No.: MFL67792702
www.lg.com
T
P
roduct Features
Fuzzy logic control
A built-in load sensor automatically detects the laundry load and a
microprocessor optimizes washing conditions such as ideal water level
and washing time.
Advanced technology is built into the Electronic Control System which
ensures the best washing result.
Turbo drum washing (option)
When "Punch + 3" washing wings turn, the washing
tub turns in the opposite direction. This makes the
both sides current of water which improve wash-
performance by rubbing clothes strongly.
Washer doesn't operate while the lid is opened. If the lid is opened during the wash,
rinse or spin cycles, the operation stops for safety.
3 Step washing
3 step washing makes the best washing performance with low tangling.
START
WASHING
AUTO
POWER
OFF
SENSING
Laundry Sensor
Water Level Sensor
SETTING
Optimum
Washing
Condition
Rubbing
Rubbing and
Shaking
Shaking and
Disentangling
Be sure to remove the unit from the carton base, otherwise
the machine will not be able to operate properly.
C
ontents
Introduction
Before Starting to Wash
Washing Programs
Additio nal Function
Options
Installation
Care and Maintenance
Troubleshooting
Terms of Warranty
Specification
Safety Information
Identification of Parts
Function Information
Preparation Before Washing
Use of Water, Detergent, Bleach and Softener
Special Guide for Stain Removal
Function of each Button
Fuzzy Wash (Normal Wash)
SOAK Wash
FAVORITE Wash
ECO SAVE
Option Washing
Delay Start (Reservation) Wash
Other Useful Functions
Placing and Leveling
Connecting Water Supply Hose
Connecting Drain Hose
Grounding Method
Cleaning and Maintenance
Common washing problems
Troubleshooting
Terms of Warranty
Specification
4
7
8
9
10
13
14
16
18
19
20
23
24
25
26
27
30
31
32
35
36
37
38
READ THIS MANUAL
Inside you will find many helpful hints on how to use and maintain your washer
properly. Just a little preventive care on your part can save you a great deal of time
and money over the life of your washer. You will find many answers to common
problems in the Troubleshooting section. If you review our chart of Troubleshooting
Tips first, you may not need to call for service at all.
afety Information
S
4
Introduction
Read carefully and thoroughly through this booklet as it contains important safety information
that will protect the user from unexpected dangers and prevent potential damages to the product.
This booklet is divided into 2 parts: Warning and Caution.
: This is a warning sign specifying user’s applications which might
be dangerous.
: This is a sign specifying ‘Strictly Forbidden’ applications.
Warning
: Failure to comply with the instructions under this
sign may result in major physical injuries or death.
Caution
: Failure to comply with the instructions under this
sign may result in minor physical injuries or
damages to the product.
Warning
WATER
HEATER
SAFETY
Caution
PROPER
INSTALLATION
• Under certain conditions hydrogen gas may be produced in a water heater
that has not been used for two weeks or more. Hydrogen gas can be
explosive under these circumstances. If the HOT water has not been used
for two weeks or more, prevent the possibility of damage or injury by turning
on all Hot water faucets and allowing them to run for several minutes. Do
this before using any electrical appliance which is connected to the HOT
water system. This simple procedure will allow any built-up hydrogen gas to
escape. Since the gas is flammable, do not smoke or use an open flame or
appliance during this process.
• The base opening must not be obstructed by carpeting when the washing
machine is installed on a carpeted floor.
• Install or store where it will not be exposed to temperatures below freezing or
exposed to the weather.
If the product is exposed to such conditions, electric shock, fire, break
down or deformation may occur.
• Properly ground washer to conform with all governing codes and ordinances.
Follow details in Installation Instructions.
If not grounded properly, break down and leakage of electricity may
occur, which may cause electric shock.
• Must be positioned so that the plug is accessible.
If the plug is placed between the wall and the machine, it may get
damaged, possibly causing fire or electric shock.
• Make sure the plug is completely pushed into the outlet.
Failure to do so may cause electric shock and fire due to overheating.
5
Introduction
Warning
There is potential danger that children might drown in the tub.
Do not touch the power plug with a wet hand.
It will cause electric shock
Do not put your hand, foot or anything under the washing machine
while the washing machine is in operation.
Caution
NOTE
afety Information
S
YOUR
LAUNDRY
AREA
WHEN USING
THE WASHER
• Keep the area underneath and around your appliances free of combustible
materials such as lint, paper, rags, chemical, etc.
Operating with such materials around the machine may trigger
explosion or fire.
• Close supervision is necessary if this appliance is used by or near children.
Do not allow children to play on, with, or inside this or any other appliance.
There is a rotating mechanism under the machine, so
you could be injured.
• Use this appliance only for its intended purpose as described in this Owner’s
Manual.
• The laundry process can reduce the flame retardant of fabrics. To avoid such
a result, carefully follow the garment manufacturer’s wash and care instructions.
• To minimize the possibility of electric shock, unplug this appliance from the
power supply or disconnect the washer at the household distribution panel
by removing the fuse or switching off the circuit breaker before attempting any
maintenance or cleaning.
: Pressing Power button to turn off does NOT
disconnect the appliance from the power supply.
• Make sure that drainage is working properly.
If water is not drained properly, your floor may get flooded. Flooded
floors may induce electricity leakage, further resulting in electric
shock or fire.
• If, during spinning, opening the lid does not stop the tub within about 15
seconds, immediately discontinue operating the machine.
Call for repair. A machine that spins with its door open may cause
injured.
Never reach into washer while it is moving.
Wait until the machine has completely stopped before opening the lid.
Even slow rotation can cause injury.
Do not use water hotter than 50°C.
Use of excessively hot water may cause damage to fabrics or
cause leakage of water.
Never attempt to operate this appliance if it is damaged, malfunctioning,
partially disassembled, or has missing or broken parts, including a
damaged cord or plug.
Operating with a damaged plug may cause electric shock.
6
Introduction
afety Information
S
Warning
• Turn off water faucets to relieve pressure on hoses and valves and to minimize
leakage if a break or rupture should occur. Check the condition of the fill hoses;
they may need replacement after 5years.
• When the air temperature is high and the water temperature is low, condensation
may occur and thus wet the floor.
• Wipe off dirt or dust on the contacts of the power plug.
Using unclean power plug may cause fire.
• Before discarding a washer, or removing it from service, remove the washer lid to
prevent children from hiding inside.
Children may be trapped and suffocated if the lid is left intact.
Do not attempt to repair or replace any part of this appliance unless
specifically recommended in this Owner’s Manual, or in published
user-repair instructions that you understand and have the skills to carry out.
Operating the machine with improperly replaced parts may be a
cause for fire or electric shock.
Do not tamper with controls.
It may lead to electric shock, fire , break down, deformation.
Do not yank the power cord in an attempt to disconnect the power plug.
Securely hold the power plug to unplug the machine.
Failure to observe these instructions may cause electric shock
or fire due to short-circuit.
When you are cleaning the washing machine, do not apply water directly
to any part of the washing machine.
It will cause short circuit and electric shock.
Caution
WHEN USING
THE WASHER
WHEN WASHER
IS NOT IN USE
Do not use a plug socket and wiring equipment for more than their
rated capacity.
Exceeding the limit may lead to electric shock, fire , break
down, and/or deformation of parts.
Do not mix chlorine bleach with ammonia or acids such as vinegar
and/or rust remover.
Mixing different chemicals can produce toxic gases which
may cause death.
Do not wash or dry articles that have been cleaned in, washed in,
soaked in, or spotted with combustible or explosive substances
(such as wax, oil, paint, gasoline, dry- cleaning solvents, kerosene,
etc). Do not add these substances to the wash water. Do not use
or place these substances around your washer or dryer during
operation.
It may ignite or explode.
denification of Parts
I
7
Introduction
WATER SUPPLY
HOSE
BLEACH
SOFTENER
INLET
DISPENSER
FUNCTION
SELECTOR
TUB
BASE
ADJUSTABLE LEGS
DRAIN HOSE
for pump model
DRAIN HOSE
POWER PLUG
START/PAUSE
BUTTON
Use to start or
stop the washing
machine
temporarily.
Make sure the
water does not
leak.
If the supply cord is
damaged, it must be
replaced by the
manufacturer or its
service agents or
similarly qualified
person in order to
avoid a hazard.
Check if the drain
hose is hung up
before operating the
washing machine.
for non pump
model
Use to level the washing
machine for correct
balance & spin
operation.
LINT FILTER
Clean regularly to
stop linting on the
clothes load.
POWDER AND LIQUID
DETERGENT BOX
Body
“ ” Part can be different according to the model.
NOTE
Drain hose Anti-rat cover (option)
Water supply hoses
or
or
1 Each for COLD and
HOT water
Accessories
unction Information
F
8
Introduction
Our machine provides various washing methods which suits various conditions and types
of laundry.
FUZZY(Normal) Wash
JEANS Wash
WOOL Wash
QUICK Wash
SOAK Wash
DELAY START Wash
OPTION Wash
Use this Program for everyday washing e.g. sheets, towels, T-shirts. (Refer to page 16)
.
EXTRA CLEANING
Use this program to get better rising performance. (Refer to page 16)
FAVORITE Wash
This setting allows you to store your FAVORITE wash conditions in the normal cycle memory..
ECO SAVE
Use this program to save water consumption. (Refer to page 20)
Use this Program for heavily soiled durable garments e.g. overalls, jeans. Thick and heavy clothes.
or those (Refer to page 16) which are excessively dirty like jeans or working uniforms can be washed.
Wool clothes (lingerie, wool, etc.) which may be easily damaged can be washed.
The fibers of machine washable woolens have been specifically modified to prevent felting when
they are machine washed. Most hand knitted garments are not made of machine washable wool
and we recommend that you hand wash them.
* Before washing your woolens check the care label for the washing instructions.
* When washing woolens use a mild Detergent recommended for washing wool.
* Hand washed woolens may be spun in a washing machine to reduce the time they take to dry.
* To dry woolens lay down them flat on a towel and pat into shape. Dry woolens out of direct sunlight.
(The heat and tumble action of a dryer may cause shrinkage or felting of woolen garments.) Some
wool underlays and sheepskin products can be washed in a washing machine but may cause pump
blockages. (Ensure that the whole article is suitable for machine washing and not just the backing
material.) You may wish to handwash these articles and place them in the machine to spin dry.
(Refer to page 16)
QUICK WASH can be selected to wash lightly soiled clothes of less than 2.0 kg in a short time.
SOAK Wash can be selected to wash heavily soiled laundry by soaking in water for some time
to remove dirt and grime. (Refer to page 18)
DELAY START Wash is used to delay the finishing time of the operation.
The number of hours to be delayed can be set by the user accordingly.
When the user needs only SPIN, RINSE/SPIN, RINSE, WASH/RINSE, WASH, WASH/RINSE/SPIN,
SOAK/WASH/RINSE/SPIN. (Refer to page 23)
TUB CLEAN
Use this program to clean the inside of washing machine especially Inner tub & Outer tub.
(Refer to page 21)
Washing according to the condition of laundry
Other washing method
Different types of laundry washing.
(Refer to page 19)
(Refer to page 20)
(Refer to page 24)
reparation Before Washing
P
9
Before Starting to Wash
WIRE
Sorting
Check before Loading
Care Labels
Long laundry items
Loading
Pretreatment on stains or heavy soil
WARNING
* Look for a care label on your clothes. This will tell you about the fabric
content of your garment and how it should be washed. Sort clothes into
loads that can be washed with the same wash cycle, Water Temperature and spin speed.
To get the best results, different fabrics need to be washed in different ways.
Separate clothes according to the type and
amount of soil.
Separate white fabrics from colored fabrics.
Separate lint producers and lint collectors.
* SOIL (Heavy, Normal, Light)
* COLOR (Whites, Lights, Darks)
* LINT (Lint producers, Collectors)
Lint Producers Terry cloth, Chenille, Towels, Nappies, Diapers
Lint Collectors Synthetics, Corduroy, Permanent Press, Socks
* Check all pockets to make sure that they are empty. Things such as nails, hair clips,
matches, pens, coins, and keys can damage both your washer and your clothes.
* Mend any torn garments or loose buttons. Tears or holes may become larger
during washing.
* Remove belts, underwires, etc. to prevent damage to the machine or your clothes.
* Pretreat any dirt and stains.
* Make sure the clothes are washable in water.
* Check the washing instructions.
* Remove tissue in pockets.
* Pre treat shirt collars and cuffs with a pre-wash product or liquid Detergent when placing them in
the washer. Before washing treat special stains with bar soaps, liquid Detergent or a paste of water and
granular Detergent.
* Use a pretreat soil and stain remover. Treat stains AS SOON AS POSSIBLE. The longer they are
left the harder they are to remove. (For more detail refer to page13)
Do not wash fabrics containing flammable materials (waxes,
cleaning fluids, etc.).
Load Size
The WATER LEVEL should just cover the clothes. Adjust the
load size accordingly. Loosely load clothes no higher than the
top row of holes in the washer tub. To add items after washer
has started, press Start button and submerge additional items.
Close the lid and press Start button again to restart.
Light and Large-sized clothing
Clothes like downs and woollens are light weight, large and float easily. Use a nylon net
and wash them in a small amount of water. If the laundry floats during the wash cycle, it
may become damaged. Use dissolved Detergent to prevent the Detergent from clumping.
Use nylon nets for long, DELICATE items. For laundry with long strings or long length ,
a net will prevent tangling during washing. Fasten zippers, hook, and strings to make
sure that these items don't snag on other clothes.
Nylon net is not supplied by LG.
Fire Hazard
Never place items in the washer that are
dampened with gasoline or other flammable
fluids.
No washer can completely remove oil.
Do not dry anything that has ever had any
type of oil on it (including cooking oils).
Doing so can result in death, explosion, or fire.
Using Detergent
Detergent
Follow the detergent package directions. Using too little detergent is a common cause of laundry problems.
Use more detergent if you have hard water, large loads, greasy or oily soils or lower water temperature.
Choosing the right detergent
We recommend the use of domestic detergent, (powder, liquid or concentrated). Soap flakes or
granulated soap powders should not be used in your washing machine. When washing woolens
remember to use detergent suitable for washing woolens.
• The temperature of the water impacts the effectiveness of all laundry additives and therefore, the
cleaning results. We recommend temperatures of:
- HOT 49~60°C…(120-140 F) White items, diapers, underclothing and heavily soiled, colorfast items.°
- WARM 29~40°C…(85-105 F) Most items°
- COLD* 18~24°C…(65-75 F) Only very bright colors with light soil.°
• When washing in COLD water additional steps may be needed:
- Adjust detergent amount and pre-dissolve detergent in warm water
- Pretreat spots and stains
- Soak heavily soiled items
- Use appropriate bleach
* Temperature below 18°C…(65 F) will not activate laundry additives and may cause lint, residue, poor°
cleaning, etc. In addition, detergent manufactures and care labels define cold water as 26 ~ 29 ° C…
(80-85° F). If the temperature of the water in the tub is too cold for your hands, the detergent will not
activate and clean effectively.
Water temperature
• The machine sets the appropriate temperature automatically according to the wash program .
• You can change the water temperature by pressing the WATER TEMP. button. (refer to page 14)
Before Starting to Wash
se of Water, Detergent, Bleach and Softener
U
Using Water
Amount of Water Level
• This machine detects the quantity of laundry automatically, then sets the
WATER LEVEL and proper amount of Detergent.
• When you select a wash program, the WATER LEVEL and amount of
Detergent (to be used) will be shown on the control panel.
• The following table shows the amount of water.
• When the WATER LEVEL is automatically detected, it may differ
depending on the quantity of laundry even
though the same WATER LEVEL is indicated on the control panel.
Attention
If iron is present in the water the clothes may become an all-over yellow or they may be stained with
brown or orange spots or streaks. Iron is not always visible. Installation of water softener or an iron filter
may be necessary for severe cases.
Before Starting to Wash
Attentión
Using Detergent
How much detergent
When you select a wash program the water level and the amount of detergent (to be used) will be
shown on the control panel. The amount of a cup in the diagram is about 40g for concentrated
detergent.
The correct amount of detergent will vary depending on the amount of soil in your clothes (Jeans
and work cloches may need more detergent, while bath towels usually need less.).
For liquid and concentrated detergents, follow the recommendations of the detergent manufacturer.
Note: To check you are using the correct amount of detergent, lift the lid of your machine
about half-way through the wash. There should be a thin layer of foam over the surface of the
water. Lots of foam may look good, but it does not contribute to cleaning your clothes. No
foam means not enough detergent has been used; soil and lint can settle back on the clothes or
the washing machine.
If excess detergent is used, the rinse will not be as clean and efficient. Also, it could cause
environmental pollution, so use it accordingly.
D nde
depo\bta e
detergente
D\bpen\bador de detergente en po\f
Adding the detergent
Open the detergent dispenser and deposit the appropriate
amount of detergent where you deposit the detergent.
Powder Detergent dispenser.
Some detergents MUST be fully dissolved before
adding to your machine to get the best wash results.
Check the instructions on the detergent packet.
If you use powdered detergent it is essential that the required amount be fully dissolved in very hot water
before being added to warm or hot water for the actual wash.
Pre-dissolving detergent in warm water when washing in cold water can improve its performance.
Where you
deposit the
detergent
Powder Detergent Box
( )
• Check clothing care label for special instructions and separate
the laundry to be bleached.
• Dilute liquid chlorine bleach.
• Measure the recommended amount of liquid bleach carefully
following instructions on the bottle.
• Before starting the washer, pour measured amount of bleach
directly into bleach dispenser. Avoid splashing or overfilling.
Powdered bleach should be mixed with water before pouring.
Using Liquid Bleach
Bleach dispenser
( )
Attention
Never pour undiluted liquid bleach directly onto clothes or into the wash basket.
This may cause change of color or damage the laundry.
Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover.
Mixing can reduce a toxic gas which may cause death.
Do not pour powdered bleach into bleach dispenser.
Before Starting to Wash
12
se of Water, Detergent, Bleach and Softener
U
Using Fabric Softener
If you wish to use fabric softener we recommend
Attention
Do not mix with detergent or bleach.
Never pour fabric softener directly on clothes. It may stain them.
Do not stop the washer during the first spin for timely dispensing.
Option washing is not designed to be used with fabric softener dispenser.
• Dilute fabric softener with water.
Undiluted fabric softener may result in spots that look like
oil stains.
• Measure and add the recommended amount of fabric
softener into the compartment marked with this symbol
( ). Follow manufacturer’s direction.
• Fabric softener is automatically dispensed in the final
rinse with indication beep.
• If you want extra rinse, you must add fabric softener
manually when indication beep rings in the final rinse.
This maximize the fabric softener function.
• Do not overfill. The dispenser hold max 35mL.
Never add more than 35mL.
Overfilling can cause early dispensing of the fabric softener
which could result in stained clothes. A cup with a pouring spout will help you avoid spilling.
• The effect of adding fabric softener may vary according to its viscosity. The stickier fabric softener
makes it effect the lower. For a sticky fabric softener it is recommended that it be diluted with water,
then be manually put during the time when the washer beeps several times before the final rinse.
This function informing correct time to dispense manually is optionally applied to some models.
Please keep it in mind that fabric softener has to be diluted with water before dispensed and never
poured directly on clothes.
Scrud (Waxy Build up)
Softener dispenser ( )
or
Scrud is the name given to the waxy build-up that can occur within any washer when the fabric
softener comes into contact with detergent. This build-up is not brought about by a fault in the
machine.
If scrud is allowed to build-up in the machine it can result in stains on your clothes or an
unpleasant smell in your washer.
• Using fabric softener sparingly.
• When filling the dispenser, do not splash or overfill.
• Clean dispenser as soon as the cycle is finished.
• Clean your machine regularly. (refer to page 32)
• Cold water washing increases the chance of this build-up occurring. We recommend a regular
warm or hot wash e.g. every 5th wash should be at least a warm one.
• Fabric softener of thinner consistency is less likely to leave residue on the dispenser and
contribute to a built-up.
pecial Guide for Stain Removal
S
13
Before Starting to Wash
• Remove stains promptly.
• Determine the kind of stain, then follow the recommended treatment in the stain
removal chart below.
• To pretreat stains, use a prewash product, liquid Detergent, or a paste made from
granular Detergent and water.
• Use COLD water on unknown stains because HOT water can set stains.
• Check care label instructions for treatments to avoid on specific fabrics.
• Check for colorfastness by testing stain remover on an inside seam.
• Rinse and wash items after stain removal.
For successful stain removal:
Follow fabric care label
instructions
■
Do not use or mix liquid chlorine bleach with other household chemicals such as toilet cleaners, rust removers, acid or
products containing ammonia. These mixtures can produce dangerous fumes which can cause serious injury or death.
■
To reduce the risk of fire or serious injury to persons or property, comply with the basic warnings listed below:
• Read and comply with all instructions on stain removal products.
• Keep stain removal products in their original labeled containers and out of children’s reach
• Thoroughly wash any utensil used.
• Do not combine stain removal products, especially ammonia and chlorine bleach. Dangerous fumes may result.
•
Never wash items which have been previously cleaned in, washed in, soaked in or spotted with gasoline, dry
cleaning solvents or other flammable or explosive substances because they give off vapors that could ignite or explode.
•
Never use highly flammable solvents, such as gasoline, inside the home. Vapors can explode on contact with flames or sparks.
WARNING
Stain Removal
STAIN
Adhesive tape, chewing gum,
rubber cement
Baby formula, dairy products, egg
Beverages (coffee, tea, soda,
juice, alcoholic beverages)
Blood
Candle wax, crayon
Chocolate
Collar or cuff soil, cosmetics
Dye transfer on white fabric
Grass
Grease, oil, tar (butter, fats, salad
dressing, cooking oils, car grease,
motor oils)
Ink
Mildew, scorch
Mud
Mustard, tomato
Nail polish
Paint, varnish
Rust, brown or yellow
discoloration
Shoe polish
Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with prewash stain
remover or nonflammable dry cleaning fluid.
Use product containing enzymes to pretreat or soak stains.
Pretreat stain. Wash using cold water and bleach safe for fabric.
Rinse with cold water. Rub with bar soap. Or pretreat or soak with product containing enzymes.
Wash using bleach safe for fabric.
Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is absorbed.
Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable dry cleaning
fluid. Hand wash to remove solvent. Wash using bleach safe for fabric.
Pretreat or soak in warm water using product containing enzymes. Wash using bleach safe for fabric.
Pretreat with prewash stain remover or rub with bar soap.
Use packaged color remover. Wash using bleach safe for fabric.
Pretreat or soak in warm water using product containing enzymes. Wash using bleach safe for fabric.
Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply
nonflammable dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinse throughly. Wash
using hottest water safe for fabric.
Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover, denatured
alcohol or nonflammable dry cleaning fluid.
Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and hot water before washing. Badly
mildewed fabrics may be permanently damaged.
Brush off dry mud. Pretreat or soak with product containing enzymes.
Pretreat with prewash stain remover. Wash using bleach safe for fabric.
May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of stain.
Repeat, replacing paper towels frequently. Do not use on acetate fabrics.
WATER BASED : Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed,
OIL BASED AND VARNISH : Use solvent recommended on can label. Rinse throughly before washing.
For spots, use rust remover safe for fabric. For discoloration of an entire load, use phosphate detergent and
nonchlorine bleach. Do not use chlorine bleach because it may intensify discoloration.
LIQUID : Pretreat with a paste of granular detergent and water. PASTE : Scrape residue from fabric. Pretreat with
prewash stain remover or nonflammable dry cleaning fluid. Rub detergent into dampened area, Wash using bleach
safe for fabric.
TREATMENT
BEEPER BUTTON
(Only 1 valve)
• Use to select the proper amount of water in relation to the
weight and type of laundry.
• Automatically controlled, but can be selected manually by
pressing the Water Button.
• WATER is automatically selected for FUZZY (Normal)
Program. The following setting are indicated as the button
is pushed.
WATER
BUTTON
WATER TEMPERATURE
BUTTON (Only 2 valves)
AIR DRY
CHILD LOCK
FUNCTION
WASH, RINSE,
SPIN BUTTON
• Use to select Water Temperatures.
Pressing the button allows you to
select COLD » WARM (HOT&COLD)
» HOT » COLD respectively.
Default setting is COLD.
• If you want to use the
washing machine
without arlam signal
sounds, press BEEPER
button allow you to
select: HIGH » OFF
» LOW » HIGH
respectively.
Default setting is HIGH.
• This button is used for
air-drying of your laundry
• Air dry selection light up in
sequence as follow
TUB DRY » 60 » 90»120 »
TUB DRY as the button is
pushed.
• Use to lock or unlock the
control button to prevent
setting from being changed
by a child.
To lock, push the RINSE and
SPIN buttons simultaneously
and to unlock push them one
more time during washing
process.
• Use when wash, rinse, spin
time need to be adjusted.
• The time increases when the
button is pressed.
• If adjustments are needed
during the wash, press the
[START/PAUSE] button before
making any changes.
• When the button is pressed
during washing, the remaining
time is displayed.
7 » 8 » 9 »10 » 1 » 2 » 3 » 4 » 5 » 6 » 7
POWER (AUTO OFF)
BUTTON
TIME LEFT, DELAY START (RESERVATION),
ALARM INDICATION
START/PAUSE
BUTTON
• Use to start or pause
the washing process.
• Repeat start and pause
by pushing the button.
• Use for selecting wash program.
• This button allows you to select 8
different programs for difference
kinds of laundry and dirtiness.
• Program selection light up in
sequence as follows: FUZZY»WOOL
»QUICK WASH»JEANS»EXTRA
CLEANING»ECO SAVE»FAVORITE»
TUB CLEAN»FUZZY etc.
Select the desired program by
pressing the button.
PROGRAM BUTTON
DELAY START
(RESERVATION)
BUTTON
• Use to set a delayed finishing
time.
• The time increase when the
button is pushed.
• The following settings are
indicated as the button is
pushed: 3 » 4 » 5 »... » 11 »
12 » 14 » 16 »... 46 » 48 » 3H.
To cancel delay time, turn the
power switch off.
(refer to page 24)
• Use to turn the power off.
• Push again and power goes
or off.
• The power goes off
automatically about 10
seconds after the wash is
finished.
• Time left - During operation, the remaining time is indicated.
• DELAY START INDICATION (RESERVATION)
- When DELAY START (RESERVATION) program is selected,
it indicates the finishing time. (RES.=DELAY)
• Alarm indication - When an error occurs, an error message
appears to indicate the abnormality. For example, indicates
that the lis is opened.
16
Washing Programs
W
ashing Programs
Washing
Programs
Add
the
laundry
Add
the Detergent
(Normal Wash)
Used for normal loads, this
mode automatically selects the
most appropriate conditions
and completes the sequence
in one operation. The built-in
sensor detects the size of the
load and the ideal wash
power and wash, rinse and
spin times are set accordingly.
Use this mode when washing
lightly soiled clothes for a short
time. The highly recommended
laundry amount is under 2.0kg.
Use this program to increase
rising performance.
This would include underwear
and baby clothes.
If someone has sensitive skin or
skin trouble,use this program.
POWER
AUTO OFF
1
1
2
5
4
3
2
* Select the
QUICK
WASH
program on
the Control
panel.
Use Jean program when
washing Jeans of different sizes
1
5
3
2
* Select the
JEANS
program on
the Control
panel.
* Spread
the jean
evenly in
the tub
1
5
3
2
* Select the
WOOL
program on
the Control
panel.
Use this program for washing
delicate fabrics such as lingerie
and woolens. (Wash only
“water washable” clothes)
Before washing your woolens
check the care label for the
washing instructions.
water washable clothes)
1
5
3
2
* Select the
EXTRA
CLEANING
program on the
Control panel.
(Wash only
* Add the appropriate
quantity of Detergent
as indicated by the
WATER LEVEL next to
WATER DETERGENT.
Or follow the Detergent
manufacturer’s
instructions
* Use neutral
Detergent appropriate
for the laundry.
* When washing
woolens use a mild
Detergent
recommended for
washing wool.
* Add the appropriate
quantity of Detergent as
indicated by the
WATER LEVEL next to
WATER DETERGENT.
* Or follow the
Detergent
manufacturer’s
instructions
17
Washing Programs
Close the lid Finish Caution & Note
STSTARART
PAUSEUSE
* The pulsator rotates for
8 seconds to detect the
laundry load.
* Then the WATER LEVEL
and the amount of
Detergent to be used
will be shown and
water will be supplied.
* Water will be
supplied for 2
minutes after the
start of the wash to
supplement the
water the laundry
has absorbed.
* When the wash
program ends, the
buzzer will ring
for 10 seconds
before the Power
goes off
automatically.
* If water is already in the tub, or putting
wet laundry into the tub before starting
will increase the WATER LEVEL.
* With lightweight bulky loads, WATER
LEVEL can be set low.
* Changes toWater Temperature
(HOT/COLD) and wash level are
possible during operation.
(refer to page 14)
3
5
6
7
6
7
6
4
4
7
6
4
* When setting the WATER LEVEL
manually, do not set to Medium to
prevent damage to laundry.
* Washing with HOT water may damage
the laundry (Water is set to cold
automatically). Ensure that the load is
under 2kg.
* In order to avoid damage to laundry,
the spin cycle may appear slow.
This also avoids wrinkles and clothing
may still contain some water. This is
normal.
* When static pressure of water is more
than 2kg/cm
2
, the QUICK WASH course
will be within 19min.
7
6
4
OAK Wash
S
18
W
ashing Program
s
minmin min minminmin min min min min min min min
Lamp
Off
Soak-Wash
Use this mode to wash normal clothes or thick and heavy clothes which are
excessively dirty. SOAK mode can be used with FUZZY or JEAN or ECO SAVE
or FAVORITE program.
PO
AUTO OFF
• SOAK will not work in WOOL and QUICK WASH,
TUB CLEAN Program.
• Keep pressing the WASH button until the light turns on
‘SOAK’ and ‘WASH’ simultaneously as next image.
• SOAK program only works when soaking time is 40, 50
or 60 minutes.
• The WATER LEVEL will be shown and water will be
supplied.
Press the POWER ( AUTO OFF) button to turn power on.
Press the PROGRAM button to select the washing program.
Add the laundry and press the START/PAUSE button.
• When the wash program ends, the buzzer will ring for
10seconds before the Power goes off automatically.
Finish
Press the WASH button, to select SOAK program.
• The appropriate quantity of Detergent marked next to the
WATER LEVEL of WATER-DETERGENT.
Add the Detergent.
• Water will be supplied for 2 minutes after the start of the
wash to supplement the absorbed water by the laundry.
Close the lid.
START
PAUSE
1
3
4
5
6
2
NOTE
• Order of Soak-Wash timing
• Select soaking time 40minutes, 50minutes, or 60minutes (Including washing time) by pressing
the Wash button repeatedly.
• If necessary, select the times of Rinse and the time for Spinning by pressing the Rinse or Spin
buttons till you reach the desired times.
AVORITE Wash
F
19
Washing Programs
Pressing the FAVORITE button allows you to store your FAVORITE wash
conditions in the normal cycle memory and then recall it for use at a later time.
POWERWER
AUTO OFF
• Press the
Press the WATER button to select WATER.
Press the WASH button, the RINSE button & the SPIN
button to select wash time, rinse time & spin time
respectively you want to store.
TEMP. button to select wash Water Temperature.
•
•
Press the POWER (AUTO OFF) button to turn power on.
Select the FAVORITE program.
Select your FAVORITE wash conditions.
Press the
START/PAUSE button to store & start your FAVORITE wash cycle.
Power turns off automatically after wash.
STSTARART
PAUSEUSE
1
2
3
4
NOTE
To recall your FAVORITE cycle.
1. Press POWER on.
2. Select the FAVORITE cycle by pressing the PROGRAM.
3. Press the START/PAUSE button. Then the wash cycle starts.
CO SAVE
E
20
Washing Programs
Use this program to save water consumption.
POWERWER
AUTO OFF
Press the
POWER (AUTO OFF) button to turn power on.
Press the PROGRAM button to select ECO SAVE program.
Press the
START/PAUSE
button.
Add the laundry into the washing tub.
Add the Detergent and close the lid.
STSTARART
PAUSEUSE
1
3
4
5
2
NOTE
• ECO SAVE is recommended program designed to minimize water consumption for normally soiled
clothing.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
