Cembre HP4-B User manual

1

MECHANICAL HAND TOOL

PINCE MECANIQUE MANUELLE

MECHANISCHE HANDZANGE

HERRAMIENTA MECANICA MANUAL

UTENSILE MECCANICO MANUALE

ENGLISH

FRANÇAIS

DEUTSCH

ESPAÑOL

ITALIANO

00 M 027

OPERATION AND MAINTENANCE MANUAL

NOTICE D'UTILISATION ET ENTRETIEN

BEDIENUNGSANLEITUNG

MANUAL DE USO Y MANTENIMIENTO

MANUALE D'USO E MANUTENZIONE

HP4-R

HP4-B

HP4-G

0.25 ÷ 1.5 mm

2

22 ÷ 16 AWG

1.5 ÷ 2.5 mm

2

16 ÷ 14 AWG

4 ÷ 6 mm

2

12 ÷ 10 AWG

2

red

blue

yellow

Type

Colour

code

Cable strip length

(mm)

for terminals

for splices

Connector

insulation

colour

TABLE 1

MECHANICAL HAND TOOL

for compression of insulated crimp connectors

1. GENERAL CHARACTERISTICS

5 ÷ 6

8 ÷ 9

7 ÷ 8

9 ÷ 10

Compression

code

red

blue

yellow

1

dot

2

dots

3

dots

ENGLISH

HP4 - R

HP4 - B

HP4 - G

– ELECTRIC RISK: do not use these tools on live cables.

– Before using the tool, carefully read instructions in this manual.

These tools are provided with a ratchet controlled mechanism, to prevent the handles opening,

before the crimping operation is complete.

The tools are supplied wrapped in anti-corrosion paper and packed in cardboard carton.

2. INSTRUCTIONS FOR USE

2.1) Strip the cable insulation, to expose a length of conductor as recommended in Table 1, taking

care not to damage or cut any of the strands.

2.2) Open the tool by fully closing the handles, until automatically released.

2.3) Insert and position the connector in the crimp aperture, as detailed in §3.1, §3.2 or §3.3. Close

the handles until the terminal is lightly held between the jaws.

2.4) Insert the stripped cable into the barrel of the connector.

2.5) Crimp the connector by fully closing the tool handles. The handles will automatically release

after completion of the crimp. Once the crimping operation has started the ratchet controlled

mechanism, prevents the jaws from re-opening, until the handles are fully closed.

2.6) Remove the crimped connector and visually check that the "Compression Code" impressed on

the insulation, corresponds to the correct choice of tool (see TABLE 1).

Type: HP4-R HP4-B HP4-G

Colour code (

handles

): Red Blue Yellow

Application range

Conductor size: mm

2

(AWG)

0.25 ÷ 1.5

(22 ÷ 16)

1.5 ÷ 2.5

(16 ÷ 14)

4 ÷ 6

(12 ÷ 10)

Dimensions (mm): length

265 320

width

80 90

Weight (kg): 0.5 0.7

3

ENGLISH

3. CONNECTOR POSITIONING

3.1) – Insulated terminals (RF, BF, GF, RP, BP, GP series)

– Male and female disconnect terminals (RF-F, RF-M, BF-F, BF-M, GF-F, GF-M series)

 Positioning:

position the connector insulation sleeve against the spring loaded, locator plate (Fig. 1).

NOTE: when using male disconnect terminals, ensure that the barb, on the spade, does not prevent the

insulation sleeve from butting against the locator plate.

3.2) – Fully insulated female disconnect terminals (RF-F..P, BF-F..P, GF-F..P series)

– Male/female connectors (RF-FM, BF-FM series)

– Bullet connectors (RF-BM, BF-BM series)

 Positioning:

manually position, the insulation sleeve on the barrel and connector, centrally in their respective

crimp apertures (Fig. 3).

NOTE: for this style of connector, the locator plate is not used and should therefore be held completely

open.

3.3) – Fully insulated male disconnect terminals (RF-M..P, BF-M..P series)

– Socket connectors (RF-BF, BF-BF series)

– Insulated splices (PL, NL series)

 Postioning:

manually position, the insulation sleeve on the barrel and connector, centrally in their respective

crimp apertures (Fig. 4).

NOTE: for this style of connector, the locator plate should be removed from the tool using a 2mm hex-

agonal key.

4. CRIMPING REGULATION ON THE INSULATION SLEEVE (See Fig. 5)

The compression on the connector insulation sleeve can be varied. Three settings are available, 1)

strong, 2) medium, 3) light to suit the diﬀ ering thickness of cable insulation.

The compression setting is varied, by altering the location of the two adjustment pins.

The most eﬀ ective compression setting can be determined, by producing crimped joints using

un-stripped cable.

Start the tests with the adjustment pins at position 3. Check the integrity of the crimped joint by

attempting to extract the cable from the connector by a pulling and twisting motion.

If the cable slides out too easily, move the two pins to the next position to obtain greater compres-

sion; repeat the test until a satisfactory result is obtained.

Before using the tool, ensure that the two pins are fully inserted into position.

5. MAINTENANCE

5.1) Before use, check that there are no traces or dust or dirt, especially in the crimping zone.

5.2) Regularly lubricate the moving parts and pivot pins with a few drops of oil.

5.3) Only use the tool for operations described in this manual.

5.4) After use, replace the tool in the cardboard carton.

5.5) In case of tool service or tool malfunction, please contact our area agent for advice.

Page is loading ...

12

FIG. 5

2

3

1

2

3

FIG. 1

FIG. 2

FIG. 3

FIG. 4

This manual is the property of Cembre: any reproduction is forbidden without written permission.

Ce manuel est la proprieté de Cembre: toute reproduction est interdite sauf autorisation écrite.

Der Firma Cembre bleibt das Eigentumsrecht der Bedienungsanleitung vorbehalten.

Ohne vorherige schriftliche Genehmigung darf die Bedienungsanleitung weder vollständig noch teilweise vervielfältigt werden.

Este manual es propiedad de Cembre. Toda reproducción está prohibida sin autorización escrita.

Questo manuale è di proprietà della Cembre: ogni riproduzione é vietata se non autorizzata per scritto.

Cembre Ltd.

Dunton Park

Kingsbury Road, Curdworth - Sutton Coldﬁeld

West Midlands B76 9EB (UK)

Tel.: +44 01675 470440 - Fax: +44 01675 470220

E-mail: [email protected]

www.cembre.co.uk

Cembre S.p.A.

Via Serenissima, 9

25135 Brescia (Italia)

Telefono: +39 030 36921

Telefax: +39 030 3365766

E-mail: [email protected]

www.cembre.com

Cembre S.a.r.l.

22 Avenue Ferdinand de Lesseps

91420 Morangis (France)

Tél.: +33 01 60 49 11 90 - Fax: +33 01 60 49 29 10

CS 92014 - 91423 Morangis Cédex

E-mail: [email protected]

www.cembre.fr

Cembre España S.L.U.

Calle Verano 6 y 8

28850 Torrejón de Ardoz

Madrid (España)

Tel.: +34 91 4852580 - Fax: +34 91 4852581

E-mail: [email protected]

www.cembre.es

Cembre GmbH

Heidemannstraße 166

80939 München (Deutschland)

Telefon: +49 89 3580676

E-mail: [email protected]

www.cembre.de

Cembre Inc.

Raritan Center Business Park

300 Columbus Cicle - Suite F

Edison, New Jersey 08837 (USA)

Tel.: +1 732 225-7415 - Fax: +1 732 225-7414

E-mail: [email protected]

www.cembreinc.com

www.cembre.com

IKUMA GmbH & Co. KG

Boschstraße 7

71384 Weinstadt (Deutschland)

Telefon: +49 7151 20536-60

Telefax: +49 7151 20536-80

E-mail: [email protected]

www.ikuma.de

cod. 6261209

Cembre HP4-B User manual

This manual is also suitable for

Cembre HP4-B User manual

in other languages

Related papers

Other documents