Poulan 545186830 User manual

Brand: Poulan

Model: 545186830

Category: Air blowers/dryers

Type: User manual

This manual is also suitable for

IMPORTANT MANUAL -- Do not throw away

MANUAL IMPORTANTE -- No lo descarte

MANUEL IMPORTANT -- À Conserver

SM210VS

ENGLISH

ESPAÑOL

FRANÇAIS

WARNING:

Read and follow all Safety Rules and Operating Instructions before

using this product. Failure to do so can result in serious injury .

ADVERTENCIA:

Lea el manual de instrucciones y siga todas las advertencias e

instrucciones de seguridad. El no hacerlo puede resultar en lesiones

graves.

AVERTISSEMENT:

Veuillez lire le manu el d’instructions e t bien respecter tous les

avertissements et toutes les instructions de sécurité. Tout défaut

de le faire pourrait entraîner des blessures graves.

Poulan PRO

1030 Stevens Creek Road

Augusta, GA 30907

Instruction Manual

Manual de Instruc c iones

Manuel d’Instructions

Please do not return unit to retailer.

Por favor, no devuelva el aparato al lugar de compra.

Veuillez ne pas retourner l’outil au détaillant.

1--800--554--6723

www.poulan--pro.com

Poulan PRO

850 Matheson Blvd. West

Mississauga, Ontario L5V 0B4

545186830 Rev. 3 3/11/09 BRW

-- 2 --

IDENTIFICATION OF SAFETY SYMBOLS

WARNING: This unit can be dangerous! Careless or improper

use can cause serious injury.

Read your operator’s manual carefully until you completely understand

and can follow all warnings and safety rules before operating the unit.

Failure to do so can result in serious injury. Save operator’s manual.

The blower can throw objects vio-

lently. You can be blinded or injured.

Always wear hearing protection and

safety glasses marked Z87. Always

wear heavy, long pants, long

sleeves, boots and gloves.

Always stop unit and disconnect spark plug before

cleaning or servicing.

Secure hair above shoulder length. Do

not wear jewelry, loose clothing, or

clothing with loosing hanging straps,

ties, tassels, etc. They can be caught in

moving parts.

Hazard zone for thrown objects. Keep children, by-

standers, and animals away from work area a mini-

mum of 30 feet (10 meters) when starting or operating

unit. Do not point blower nozzle in the direction of

people or pets.

WARNING: Stop the engine before opening the vacuum inlet door. The engine must

be stopped and the impeller blades no longer turning to avoid serious injury from the rotating

blades. Gently tilt the handle of the screwdriver toward the front of the unit to release the latch

while pulling up on the vacuum inlet cover with your other hand.

-- 3 --

IDENTIFICATION OF SAFETY SYMBOLS

WARNING: Fire hazard. Never mix, pour, or store gasoline or

use the unit near a flame or sparks (including smoking, open flames, or

work that can cause sparks).

When using the vacuum attachment, the unit is designed to pick up dry

material such as leaves, grass, small twigs, and bits of paper. Do not

vacuum stones, gravel, metal, broken glass, etc., to avoid severe dam-

age to the impeller.

WARNING: The muffler is very hot during and after use. Do

not touch the muffler , muf fler guard, or surrounding surfaces, or allow

combustible material such as dry grass or fuel to do so.

SAFETY RULES

WARNING: Failure to follow all

Safety Rules and Precautions can result in

serious injury.

KNOW YOUR UNIT

S Read your instruction manual carefully until

you completely understand and can follow

all warnings and safety rules before operat-

ing the unit.

D Restrict unit to users who understand and

will follow all warnings and safety rules in

this manual.

WARNING: Inspect area before start-

ing unit. Remove all debris and hard objects

such as ro cks, gla ss, wire, etc. tha t can rico-

chet, be thrown, or otherwise cause injury or

damage during operation.

Use your unit as a blower for:

D Sweeping debris or grass clippings from

driveways, sidewalks, patios, etc.

D Blowing grass clippings, straw, or leaves into

piles, around joints, or between bricks.

Use your unit as a vacuum for:

D Picki n g up dry mat e r ial such as lea ve s,

grass, small twigs, and bits of paper .

D For best results during vacuum use, operate

your unit at high speed.

D Move slowly back and forth over the mate-

rial as you vacuum. Avoid forcing the unit

into a pile of debris as this can clog the unit.

D Keep the vacuum tube about an inch above

the ground for best results.

PLAN AHEAD

D Always wear eye protection when operat-

ing, servicing, or performing maintenance

on unit. Wearing eye protection will help to

prevent rocks or debris from being blown or

ricocheting into eyes and face which can

result in blindness and/or serious injury.

Eye protection should be marked Z87.

D Always wear foot protection. Do not go

barefoot or wear sandals.

D Always wear respirator or face mask when

working with unit in dusty environments.

D Secure hair so it is above shoulder length.

Keep loose hair , loose clothing, fingers, and

all other parts of the body away from openings

and moving parts. Hair , jewelry, loose cloth-

ing, or clothing with loosely hanging straps,

ties, tassels, etc., can be caught in moving

parts.

D Do not operate unit when you are tired, ill, up-

set, or if you are under the influence of alco-

hol, drugs, or medication.

D Keep children, bystanders, and animals

away from work area a minimum of 30 feet

(10 meters) when starting or operating unit.

Do not point the blower nozzle in the direc-

tion of people or pets.

HANDLE FUEL WITH CAUTION, IT IS

HIGHLY FLAMMABLE

D Eliminate all sources of sparks or flame (in-

cluding smoking, open flames, or work that

can cause sparks) inthe areas where fuel is

mixed, poured, or stored.

D Mix and pour fuel in an outdoor area; store

fuel in a cool, dry, well ventilated place; use

an approved, marked container for all fuel

purposes.

D Do not smoke while handling fuel or while

operating the unit.

D Make sure the unit is properly assembled

and in good operating condition.

D Do not fill fuel tank while engine is hot or

running.

D Avoid spilling fuel or oil. Wipe up fuel spills

before starting engine.

-- 4 --

D Move at least 10 feet (3 meters) away from

fuel and fueling site before starting engine.

D Always store gasoline in a container ap-

proved for flammable liquids.

OPERATE YOUR UNIT SAFELY

WARNING: Stop the engine before

opening the vacuum inlet door . The engine

must be stopped and the impeller blades no

longer turning to avoid serious injury from the

rotating blades.

D Inspect unit before each use for worn,

loose, missing, o r damaged parts. Do not

use until unit is in proper working order.

D Keep outside surfaces free of oil and fuel.

D Never start or run engine inside a closed

room, building or other unventilated area.

Breathing exhaust fumes can kill.

D To avoid static electricity discharge, do not

wear rubber gloves or any other insulated

gloves while operating unit.

D Do not set unit on any surface except a

clean, hard area while engine is running.

Debris such as gravel, sand, dust, grass,

etc. could be picked up by the air intake a nd

thrown out through discharge opening,

damaging unit, property , or causing serious

injury to bystanders or operator .

D Avoid dangerous environments. Do not use

in unventilated areas or where explosive

vapors or carbon monoxide build up could

be present.

D Do not overreach or use from unstable sur-

faces such as ladders, trees, steep slopes,

rooftops, etc. Keep firm footing and balance

at all times.

D Never place objects inside the blower

tubes; always direct the blowing debris

away from people, animals, glass, and solid

objects such as trees, automobiles, walls,

etc. The force of aircan causerocks, dirt, or

sticks to be thrown or to ricochet which can

hurt people or animals, break glass, or

cause other damage.

D Never run unit without the proper equip-

ment attached. When using your unit as a

blower , always install blower tubes. When

using your unit as a vacuum, always install

vacuum tubes and vacuum bag assembly.

Make sure vacuum bag assembly is com-

pletely zipped.

D Check air intake opening, blower tubes,

vacuum tubes, and elbow tube frequently,

always with engine stopped and spark plug

disconnected. Keep vents and discharge

tubes free of debris which can accumulate

and restrict proper air flow.

D Never place any object in the air intake open-

ing as this could restrict proper air flow and

cause damage to the unit.

D Never use for spreading chemicals, fertiliz-

ers, or other substances which may contain

toxic materials.

D To avoid spreading fire, do not use near leaf

or brush fires, fireplaces, barbecue pits,

ashtrays, etc.

D Use only for jobs explained in this manual.

MAINTA IN YOUR UNIT PROPERLY

WARNING: Disconnect spark plug be-

fore performing maintenance except for carbu-

retor adjustmen ts.

D Have all maintenance other than the rec-

ommended procedures described in the in-

struction manual performed by an autho-

rized service dealer.

D Use only recommended Po ul an PR O re-

placement parts; use of any other parts

may void your warranty and cause damage

to your unit.

D Empty fuel tank before storing the unit. Use

up fuel left in carburetor by starting engine and

letting it run until it stops.

D Do not use any accessory or attachment

other than those recommended by manufac-

turer for use with your unit.

D Do not store the unit or fuel in a closed area

where fuel vapors can reach sparks or an

open flame from hot water heaters, electric

motors or switches, furnaces, etc.

D Store in a dry area out of reach of children.

WARNING: The engine exhaust from

this product contains chemicals known to the

State of California to cause cancer, birth de-

fects or other reproductive harm.

SPECIAL NOTICE: Exposure to vibra-

tions through prolonged use of gasoline pow-

ered hand tools could cause blood vessel or

nerve damage in the fingers, hands, and

joints of people prone to circulation disorders

or abnormal swelling. Prolonged use in cold

weather has been linked to blood vessel dam-

age in otherwise healthy people. If symptoms

occur such as numbness, pain, loss of

strength, change in skin color or texture, or

loss of feeling in the fingers, hands, or joints,

discontinue the use of this tool and seek

medical attention. An antivibration system

does not guarantee the avoidance of these

problems. Users who operate power tools on

a continual and regular basis must monitor

closely their physical condition and the condi-

tion of this tool.

SPECIAL NOTICE: This unit is equipped

with a temperature limiting muffler and spark

arresting screen which meets the require-

ments of California Codes 4442 and 4443. All

U.S. forest land and the states of California,

Idaho, Maine, Minnesota, New Jersey, Ore-

gon, and Washington require by law that

many internal combustion engines be

equipped with aspark arresting screen. If you

operate in a locale where such regulations ex-

ist, you are legally responsible for maintaining

the operating condition of these parts. Failure

to do so is a violation of the law. Refer to the

MAINTENANCE section for information on

maintenance of the muffler and spark arrest-

ing screen.

-- 5 --

ASSEMBLY

WARNING: Stop engine and be sure

the impeller blades have stopped turning be-

fore opening the vacuum inlet door or at-

tempting to insert or remove the vacuum or

blower tubes. The rotating blades can cause

serious injury. Always disconnect the spark

plug before performing maintenance or ac-

cessing movable parts.

WARNING: If you receive your unit

assembled, check each step to insure your

unit is properly assembled and all fasteners

are secure. Follow all safety information in

the manual and on the unit.

D A standard screwdriver is required for as-

sembly.

BLOWER TUBE ASSEMBLY

1. Align the rib on the upper blower tube with

the groove in the blower outlet; slide the

tube into place.

NOTE: Knob must be loose enough to allow

blower tube to be inserted in blower outlet. Loos-

en knob by turning counterclockwise.

Blower Outlet

Rib

Groove

2. Secure the tube by turning the knob clock-

wise.

3. Align the slots on the lower blower tube

with the tabs on the upper blower tube.

Upper Blower Tube

Tab

Slot

Lower Blower Tube

4. Slide the lower blower tube onto the upper

blower tube.

5. Turn the lower blower tube clockwise until

a click is felt to secure the lower blower

tube to the upper blower tube.

NOTE: When the upper and lower blower

tubes are assembled together properly, the

arrows on both tubes will be aligned.

6. To remove the tubes, turn the knob coun-

terclockwise to loosen the tubes; remove

the tubes.

HIGH --SPEED NOZZLE ASSEMBLY

When greater air speed is desired, use the

high--speed nozzle.

1. Align the slots on the nozzle with the tabs

on the lower blower tube.

High--

Speed

Nozzle

Tab

Slot

Lower Blower

Tube

2. Slide the nozzle onto the lower blower tube.

3. Turn the nozzle clockwise until a click is

felt to secure the nozzle to the lower blow-

er tube.

VACUUM BAG ASSEMBLY

1. Open the zipper on the vacuum bag and

insert the elbow tube.

2. Push the small end of the elbow tube

through the small opening in the bag.

Small Opening

Zipper

Opening

Elbow

Tube

Rib

NOTE: Make sure edge of the small opening

is flush against the flared area of the elbow tube,

and the rib on the elbow tube is on the bottom.

3. Close the zipper on the bag. Make sure the

zipper is closed completely.

4. Remove blower tubes from engine.

Rib

Groove

5. Insert the elbow tube into the blower outlet.

Make sure elbow tube rib is aligned with

the blower outlet groove.

6. Turn knob clockwise to secure elbow tube.

VACUUM TUBE ASSEMBLY

WARNING: Stop engine and be sure

the impeller blades have stopped turning be-

fore opening the vacuum inlet door or at-

tempting to insert or remove the vacuum or

blower tubes. The rotating blades can cause

serious injury.

-- 6 --

1. Insert the tip of a screwdriver into the latch

area of the vacuum inlet.

Latch

Area

Blower

Outlet

Vacuum Inlet Cover

Latch Area

2. Gently tilt the handle of the screwdriver to-

ward the front of the unit to release the

latch while pulling up on the vacuum inlet

cover with your other hand.

3. Hold the vacuum inlet cover open until up-

per vacuum tube is installed.

Vacuum

Inlet

Cover

Vacuum Inlet

4. Align the tabs on the inside of the vacuum in-

let with the slots on the upper vacuum tube.

Tab

Slot

5. Push the upper vacuum tube into the vac-

uum inlet. Turn the tube counterclockwise

until a click is felt to secure the tube to the

blower unit.

6. Align slanted end of lower vacuum tube as

shown. Firmly push lower vacuum tube

into upper vacuum tube.

Slanted end of

lower vacuum tube

HOW TO CONVERT UNIT FROM

VACUUM USE TO BLOWER USE

1. Remove the elbow tube and vacuum bag

by turning the knob counterclockwise to

loosen the elbow tube.

2. Remove the vacuum tubes by turning the

tubes clockwise.

3. Close the vacuum inlet cover and make

sure it is latched closed.

4. Reinstall the blower tubes (see BLOWER

TUBE ASSEMBLY).

SHOULDER STRAP ADJUSTMENT

1. Hold the unit as shown with the muffler side

facing away from your body and clothes.

2. Pass the shoulder strap over your head

and onto your right shoulder.

3. Extend your left arm toward the rear of the

vacuum bag.

4. Adjust shoulder strap until the vacuum

bag/shoulder strap seam lies between

your thumb and index finger.

5. Make sure air flows freely from the elbow

tube into bag. If bag is kinked, the unit will

not operate properly.

-- 7 --

OPERATION

KNOW YOUR BLOWER

READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR UNIT.

Compare the illustrations with your unit to familiarize yourself with the location of the various controls

and adjustments. Save this manual for future reference.

MULCHING BLADES

Your blower is equipped with mulching blades as a standard feature. When using the vacuum

attachment, the mulching blades automatically reduce debris at a ratio of up to 16:1.

Start Lever

Fuel Mix

Fill Cap

Starter

Rope

Throttle

Trigger

Spark

Plug

Upper Blower Tube

Primer

Button

Vacuum Handle

Lower Vacuum Tube

Upper Vacuum Tube

Vacuum Bag

Elbow Tube

High--Speed

Nozzle

Lower Blower Tube

STOP

Switch

STOP SWITCH

The STOP switch is used to stop the engine.

To stop the engine, push and hold the STOP

switch in the STOP position until the engine

stops.

THROTTLE TRIGGER

The THROTTLE TRIGGER is used to select

the desired engine speed.

PRIMER BUTTON

The PRIMER BUTTON removes air from the

carburetor and fuel lines and fills them with fuel.

Thisallowsyoutostarttheenginewithfewer

pulls on the starter rope. Activate primer button

by pressing it and allowing it to return to its origi-

nal position.

START LEVER

The START LEVER helps to supply fuel to the

engine to aid in starting. Activate the starting

system by moving the sta r t lever to the STAR T

position. DO NOT squeeze the throttle trigger

until the engine has started and runs. After the

engine starts, allow the engine to warm--up

10--15 seconds, then fully squeeze the throttle

trigger to deactivate the starting system.

OPERATING POSITION

Blower Vacuum

OPERATING TIPS

S While vacuuming or blowing debris, hold

the unit with the muffler side facing away

from your body and clothes (see OPERA T-

ING POSITION illustration above).

S To reduce the risk of hearing loss

associated with sound level(s), hearing

protection is required.

S To reduce the risk of injury associated with

contacting rotating parts, stop the engine be-

fore installing or removing attachments. Do

not operate without guard(s) in place.

S Operate power equipment only at reasonable

hours--not early in the morning or late at night

when people might be disturbed. Comply with

times listed in local ordinances. Usual recom-

mendations are 9:00 a.m. to 5:00 p.m.,

Monday though Saturday.

S To reduce noise levels, limit the number of

pieces of equipment used at any one time.

-- 8 --

S To reduce noise levels, operate power

blowers at the lowest possible throttle

speed to do the job.

S Use rakes and brooms to loosen debris be-

fore blowing.

S In dusty conditions, slightly dampen sur-

faces or use a mister attachment when wa-

ter is available.

S Conserve water by using power blowers

instead of hoses for many lawn and garden

applications, including areas such as gutters,

screens, patios, grills, porches, and gardens.

S Watch out for children, pets, open windows,

or freshly washed cars. Blow debris away

safely.

S Use the full blower nozzle extension so the

air stream can work close to the ground.

S After using blowers and other equipment,

CLEAN UP! Dispose of debris in trash re-

ceptacles.

BEFORE STARTING EN GINE

WARNING: Be sure to read the fuel

information in the safety rules before you be-

gin. If you do not understand the safety rules,

do not attempt to fuel your unit. Call

1-800-554-6723.

FUELING ENGINE

WARNING: Remove fuel cap slowly

when refueling.

HELPFUL TIP

To obtain the correct oil mix

ratio, pour 3.2 ounces of

2--cycle synthetic oil into

one gallon of fresh gas.

This engine is certified to operate on unleaded

gasoline. Before operation, gasoline must be

mixed with a good quality synthetic 2-cycle

air-cooled engine oil designed to be mixed at a

ratio of 40:1. Poulan PRO brand synthetic oil is

recommended. Mix gasoline and oil at a ratio of

40:1. A 40:1 ratio is obtained by m ixing 3.2 fluid

ounces (95 ml) of oil with 1 gallon (4 liters) of

unleaded gasoline. DO NOT USE automotive

oil or marine oil. These oils will cause engine

damage. When mixing fuel, follow instructions

printed on container . Once oil is added to

gasoline, shake container momentarily to

assure that the fuel is thoroughly mixed. Always

read and follow the safety rules relating to fuel

before fueling your unit.

CAUTION : Never use str ai ght gas olin e in

your unit. This will cause permanent engine

damage and void the limited warranty.

FUEL REQUIREMENTS

This engine requires the use of minimum 87

octane [R+M]/2 clean gasoline.

IMPORTANT

Use of alcohol blended fuels (called gasohol or

using ethanol or methanol) can cause major

engine performance and durability problems.

WARNING: Alternative fuels (not gas-

oline) such as E--15 (15% alcohol), E--20 (20%

alcohol), E--85 (85% alcohol) are NOT classified

as gasoline and are NOT approved for use in

2--stroke gasoline engines. Use of alternative

fuels will cause problems such as: improper

clutch engagements, overheating, vapor lock,

power loss, lubrication deficiency, deterioration

of fuel lines, gaskets and internal carburetor

components, etc. Alternative fuels cause high

moisture absorption into the fuel/oil mixture

leading to oil and fuel separation.

HOW TO STOP YOUR ENGINE

D Release the throttle trigger .

S Push and hold the STOP switch in the

STOP position until the engine stops.

HOW TO START YOUR ENGINE

WARNING: You MUST make sure

the tubes are secure before using the unit.

D Fuel engine. Move at least 10 feet (3 me-

ters) away from the fueling site.

D Hold the unit in the starting position as

shown. Make sure the blower end is di-

rected away from people, animals, glass,

and solid objects.

Blower

Vacuum

STARTING POSITION

WARNING: When starting engine,

hold the unit as illustrated. Do not set unit on any

surface except a clean, hard area when starting

engine or while engine is running. Debris such

as gravel, sand, dust, grass, etc. could be

picked up by the air intake and thrown out

through the discharge opening, damaging the

unit or property , or causing serious injury to by-

standers or the operator .

HELPFUL TIP

If your engine still does not

start after following these

instructions, please call

1--800--554--6723.

STARTING A COLD ENGINE (or warm

engine after runni ng out of fuel)

1. Move the throttle position lever (cruise con-

trol) to the idle position.

-- 9 --

Throttle

Position

Lever

(Cruise

Control)

2. Slowly press the primer bulb 6 times.

3. Move the start lever to the ST ART position.

Start

Lever

Starter

Handle

Primer

Bulb

4. Pull starter rope handle sharply until en-

gine starts and runs.

5. Allow unit to run for 10--15 seconds, then ful-

ly squeeze the throttle trigger to disengage

the starting system.

STARTING A WARM ENGINE

1. Squeeze and hold the throttle trigger.

2. Pull starter rope sharply while squeezing

throttle trigger until engine runs.

NOTE: Normally , the warm starting proce-

dure can be used within 5--10 minutes after

the unit is turned off. If the unit sits for more

than 10 minutes without being used, it will be

necessary to start the unit by following the

steps under STARTING A COLD ENGINE or

following the starting instruction steps shown

on the unit.

STARTING A FLOODED ENGINE

Flooded engines can be started by moving the

start lever to the RUN position and fully

squeezing the throttle trigger. Pull the starter

handle repeatedly while squeezing throttle

trigger until engine starts and runs. This could

require pulling the starter handle many times,

depending on how badly the unit is flooded. If

the unit still doesn’t start, refer to the TROU-

BLESHOOTING TABLE or call

1-800-554-6723.

MAINTENANCE

WARNING: Avoid touching muffler

unless engine and muffler are cold. A hot

muffler can cause serious burns.

WARNING: Stop engine and be sure

the impeller blades have stopped turning be-

fore opening the vacuum inlet door or at-

tempting to insert or remove the vacuum or

blower tubes. The rotating blades can cause

serious injury. Always disconnect the spark

plug before performing maintenance or ac-

cessing movable parts.

HELPFUL TIP

IMPORTANT: Have all

repairs other than the rec-

ommended maintenance

described in the instruction

manual performed by an

authorized service dealer.

If any dealer other than an authorized

service dealer performs work on the

product, Poulan PRO may not pay for

repairs under warranty. It is your re-

sponsibility to maintain and perform

general maintenance.

GENERAL RECOMME ND ATIONS

The warranty on this unit does not cover items

that have been subjected to operator abuse

or negligence. To receive full value from the

warranty, the operator must maintain unit as

instructed in this manual. Various adjust-

ments will need to be made periodically to

properly maintain your unit.

CHECK FOR LOOSE

FASTENERS AND PARTS

S Muffler

S Spark Plug Boot

S Air Filter

S Housing Screws

CHECK FOR DAMAGED OR WORN

PARTS

Contact an authorized service dealer for re-

placement of damaged or worn parts.

S Fuel Tank -- Do not use unit if fuel tank shows

signs of damage or leaks.

S Vacuum Bag -- Do not use vacuum bag if it

is torn or damaged.

INSPECT A ND CL EAN UNIT AND

DECALS

S After each use, inspect complete unit for

loose or damaged parts. Clean the unit and

decals using a damp cloth with a mild deter-

gent.

-- 1 0 --

S Wipe off unit with a clean dry cloth.

CLEAN AIR FILTER

A dirty air filter decreases engine perform-

ance and increases fuel consumption and

harmful emissions. Always clean or replace

air filter after every 5 hours of operation or

yearly , whichever comes first.

Air Filter

Cover

Air Filter

Button

Cleaning the air filter:

1. Clean the cover and the area around it to

keep debris from falling into the carburetor

chamber when the cover is removed.

NOTE: Move choke lever to RUN position

before opening air filter cover.

2. Open air filter cover by pushing button

(see illustration). Remove air filter .

NOTE: Do not clean filter in gasoline or other

flammable solvent. Doing so can create a fire

hazard or produce harmful evaporative emis-

sions.

3. Wash the filter in soap and water.

4. Allow filter to dry.

5. Apply a few drops of oil to the filter;

squeeze filter to distribute oil.

6. Replace parts.

REPLACE SPARK PLUG

Replace spark plug each year to ensure the

engine starts easier and runs better. Set

spark plug gap at 0.025 inch (0.6 mm). Igni-

tion timing is fixed, nonadjustable.

1. Twist, then pull off spark plug boot.

2. Remove spark plug from cylinder and dis-

card.

3. Replace with Champion RCJ-6Y spark

plug and tighten securely with a 3/4 inch

(19 mm) socket wrench.

4. Reinstall the spark plug boot.

REPLACE FUEL FILT E R

To replace fuel filter , drain unit by running it dry

of fuel, then remove fuel cap/retainer assem-

bly from tank. Pull filter from tank and remove

it from the fuel line. Install new fuel filter on fuel

line; reinstall parts.

Fuel Line

Fuel Filter

CHECK MUFFLER MOUNTING

SCREWS

Once each year, ensure muffler mounting

screws are tightened securely to prevent

damage.

Muffler

Mounting

Screw

INSPECT M UFFL ER AND SPARK

ARRESTING SCREEN

WARNING: The muf fler on this prod-

uct contains chemicals known to the State of

California to cause cancer .

As the unit is used, carbon deposits build up

on the muffler and spark arresting screen,

and must be removed to avoid creating a fire

hazard or affecting engine performance.

Hood

Screws

Spark

Arresting

Screen

Muffler Cover

Replace the spark arresting screen every 50

hours of operation or if any damage or breaks

in the screen are noted.

NOTE: Do not attempt to clean the spark ar-

resting screen.

1. Remove 3 screws from muffler cover.

Remove muffler cover.

2. Loosen and remove 4 screws from the

muffler hood.

3. Remove the muffler hood and spark arrest-

ing screen.

4. Install new spark arresting screen.

5. Reinstall muffler hood and 4 screws. Tight-

en sc rews securely.

6. Reinstall muf fler cover and 3 screws.

Tighten securely.

NOTE: If any part of the muf fler is cracked,

broken or damaged, we recommend that the

muffler be replaced.

CARBURETOR IDLE SPEED

ADJUSTMENT

The carburetor has been carefully set at the

factory. Adjustments may be necessary if you

notice any of the following conditions:

S Engine will not idle when the throttle is re-

leased.

-- 11 --

To adjust idle speed:

Allow engine to idle. Adjust speed until engine

runs without stalling (idle speed too slow).

S Turn idle speed screw clockwise to in-

crease engine speed if engine stalls or dies.

S Turn idle speed screw counterclockwise to

decrease engine speed.

Air

Filter

Cover

Idle Speed Screw

If you require further assistance or are unsure

about performing this procedure, contact an

authorized service dealer or call

1--800--554--6723.

STORAGE

WARNING: Perform the following

steps after each use:

S Allow engine to cool, and secure the unit

before storing or transporting.

S Store unit and fuel in a well ventilated area

where fuel vapors cannot reach sparks or

open flames from water heaters, electric

motors or switches, furnaces, etc.

S Store unit with all guards in place. Position

unit so that any sharp object cannot acci-

dentally cause injury .

S Store unit and fuel well out of the reach of

children.

SEASONAL STORAGE

Prepare unit for storage at end of season or if

it will not be used for 30 days or more.

If your unit is to be stored for a period of time:

S Clean the entire unit before lengthy stor-

age.

S Store in a clean dry area.

S Lightly oil external metal surfaces.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA-

TION section of this manual, see message la-

beled IMPORTANT regarding the use of ga-

sohol in your engine.

Fuel stabilizer is an acceptable alternative in

minimizing the formation of fuel gum deposits

during storage. Add stabilizer to gasoline in fuel

tank or fuel storage container . Follow the mix

instructions found on stabilizer container . Run

engine at least 5 minutes after adding stabilizer .

HELPFUL TIP

During storage of your gas/

oil mixture, the oil will sepa-

rate from the gas.

We recommend that you

shake the gas can weekly

to insure proper blending of

the gas and oil.

ENGINE

S Remove spark plug and pour 1 teaspoon of

40:1, 2-cycle engine oil (air cooled) through

the spark plug opening. Slowly pull the

starter rope 8 to 10 times to distribute oil.

S Replace spark plug with new one of recom-

mended type and heat range.

S Clean air filter.

S Check entire unit for loose screws, nuts,

and bolts. Replace any damaged, broken,

or worn parts.

S At the beginning of the next season, use

only fresh fuel having the proper gasoline to

oil ratio.

OTHER

S Do not store gasoline from one season to

another.

S Replace your gasoline can if it starts to rust.

-- 1 2 --

TROUBLE

CAUSE REMEDY

Engine will not

start.

1. Engine flooded.

2. Fuel tank empty.

3. Spark plug not firing.

4. Fuel not reaching

carburetor.

5. Compression low.

1. See “Starting a Flooded Engine”

in Operation section.

2. Fill tank with correct fuel mixture.

3. Install new spark plug.

4. Check for dirty fuel filter; replace.

Check for kinked or split fuel line;

repair or replace.

5. Contact an authorized service dealer.

Engine will not

idle properly.

1. Fuel not reaching

carburetor.

2. Carburetor requires

adjustment.

3. Crankshaft seals worn.

4. Compression low.

1. Check for dirty fuel filter; replace.

Check for kinked or split fuel line;

repair or replace.

2. See “Carburetor Idle Speed Adjustment”

in Service and Adjustments Section.

3. Contact an authorized service dealer

4. Contact an authorized service dealer.

1. Air filter dirty.

2. Fuel not reaching

carburetor .

3. Spark plug fouled.

4. Carburetor requires

adjustment.

5. Carbon build up.

6. Compression low.

Engine will not

accelerate,

lacks power, or

dies under a

load.

1. Clean or replace air filter.

2. Check for dirty fuel filter; replace.

Check for kinked or split fuel line;

repair or replace.

3. Clean or replace spark plug

and re-gap.

4. Contact an authorized service dealer.

5. Contact an authorized service dealer.

6. Contact an authorized service dealer.

Engine smokes

excessively.

1. Choke partially on.

2. Fuel mixture incorrect.

3. Air filter dirty.

4. Carburetor requires

adjustment.

1. Adjust choke.

2. Empty fuel tank and refill with

correct fuel mixture.

3. Clean or replace air filter .

4. Contact an authorized service dealer.

Engine runs hot.

1. Fuel mixture incorrect.

2. Spark plug incorrect.

3. Carburetor requires

adjustment.

4. Carbon build up.

1. See “Fueling Engine” in Operation

section.

2. Replace with correct spark plug.

3. Contact an authorized service dealer.

4. Contact an authorized service dealer.

TROUBLESHOOTING TABLE

WARNING: Always stop unit and disconnect spark plug before performing any of the

recommended remedies below other than remedies that require operation of the unit.

-- 1 3 --

LIMITED WARRANTY

Poulan PRO, a division of Husqvarna Consum-

er Outdoor Products N.A., Inc., warrants to the

original consumer purchaser that each new

Poulan PRO brand gasoline tool or attachment

is free from defects in material and workman-

ship and agrees to repair or replace under this

warranty any defective gasoline product or at-

tachment as follows from the original date of

purchase.

2YEARS--Parts and Labor , when used for

household purposes.

90 DA YS -- Parts and Labor , when used for

commercial, professional, or income producing

purposes.

30 DA YS -- Parts and Labor , if used for rental

purposes.

This warranty is not transferable and does not

cover damage or liability caused by improper

handling, improper maintenance or alteration,

or the use of accessories and/or attachments

not specifically recommended by Poulan

PRO for this tool. This warranty does not cov-

er tune--up, spark plugs, filters, starter ropes,

or blower and vacuum tubes that will wear

and require replacement with reasonable use

during the warranty period. This warranty

does not cover pre--delivery setup or normal

adjustments explained in the instruction

manual. This warranty does not cover trans-

portation costs.

In the event you have a claim under this warran-

ty, you must return the product to an authorized

service dealer .

Should you have any unanswered questions

concerning this warranty, please contact:

Poulan PRO, a division of Husqvarna

Consumer Outdoor Products N.A., Inc.

1030 Stevens Creek Road

Augusta, GA 30907

1--800--554--6723

In Canada, contact:

Poul an PRO

850 Matheson Blvd. West

Mississauga, Ontario L5V 0B4

Giving the model number, serial number and

date of purchase of your product and the name

and address of the authorized dealer from

whom it was purchased.

THIS WARRANTY GIVES YOU SPECIFIC

LEGAL RIGHTS, AND YOU MAY HAVE OTH-

ER RIGHTS WHICH V AR Y FROM ST ATE T O

STA T E.

NO CLAIMS FOR CONSEQUENTIAL OR

OTHER DAMA GES WIL L BE ALL OWE D,

AND THERE ARE NO OTHER EXPRESS

WARRANTIES EXCEPT THOSE EX-

PRESSL Y STIPULA TED HEREIN.

SOME ST ATES DO NOT ALLOW LIMIT A-

TIONS ON HOW LONG A N IMPL IE D W AR-

RANTY LASTS OR THE EXCLU SI ON OR

LIMITATIONS OF INCIDENTAL OR CONSE-

QUENTIAL DAMAGES, SO THE ABOVE LIM-

ITATIONS OR EXCLUSION MA Y NOT APPL Y

TO YOU.

This is a limited warranty within the meaning of

that term as defined in the Magnuson--Moss Act

of 1975.

The policy of Poulan PRO is to continuously

improve its products. Therefore, Poulan

PRO reserves the right to change, modify, or

discontinue models, designs, specifications,

and accessories of all products at any time

without notice or obligation to any purchaser.

U.S. EPA/CALIFORNIA/ENVIRONMENT CANADA

EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND O B-

LIGATIONS: The U.S. Environmental

Protection Agency, California Air Resources

Board, Environment Canada and Poulan

PRO are pleased to explain the emissions con-

trol system warranty on your year 2009 and lat-

er small off--road engine. In California, all small

off--road engines m ust be designed, built, and

equ ip pe d to mee t the State’s stringent anti--

smog standards. Poulan PRO must warrant

the emission control system on your small

off--road engine for the periods of time listed

below provided there has been no abuse, ne-

glect, or improper maintenance of your small

off--road engine. Yo ur emissio n con trol system

includes parts such as the carburetor, the igni-

tion system and the fuel tank. Where a warrant-

able condition exists, Poulan PRO will repair

your small off--road engine at no cost to you.

Expenses covered under warranty include

diagnosis, parts and labor .

MANUFACTURER’S WARRANTY COV-

ERAGE: If any emissions related part on your

engine (as listed under Emissions Control

Warranty Parts List) is defective or a defect in

the materi als or workmanship of the engine

causes the failure of such an emission related

part, the part will be repaired or replaced by

Poulan PRO. OWNER’S WARRANTY RE-

SPONSIBILITIES: As the small off--road en-

gine owner, you are responsible for the per-

formance of the required maintenance listed

in your instruction manual. Poulan PRO rec-

ommends that you retain all receipts covering

maintenance on your small off--road engine,

but Poulan PRO cannot deny warranty solely

for the lack of receipts or for your failure to en-

sure the performance of all scheduled main-

tenance. As the small off--road engine owner,

you should be aware that Poulan PRO may

deny you warranty coverage if your small off--

road engine or a part of it has failed due to

-- 1 4 --

abuse, neglect, improper maintenance, un-

approved modifications, or the use of parts

not made or approved by the original equip-

ment manufacturer . You are responsible for

pres enting your small off--road engine to an

Poulan PRO authorized repair center as soon

as a problem exists. Warranty repairs should

be completed in a reasonable amount of time,

not to exceed 30 days. If you have any ques-

tions regarding your warranty rights and re-

sponsibilities, you should contact your near-

est authorized service center, call Poulan

PRO at 1--800--554--6723, or send e-mail cor-

respondence to emission.warranty@HCOP--

emission.com. WARRANTY COMMENCE-

MENT DA TE: The warranty period begins on

the date the small off--road engine is pur-

chased. LENGTH OF COVERAGE: This

warranty shall be for a period of two years

from the initial date of purchase. WHAT IS

COVERED: REPAIR OR REPLACEMENT

OF PARTS. Repair or replacement of any

warranted part will be performed at no charge

to the owner at an approved Poulan PRO

servicing center. If you have any questions

regarding your warranty rights and responsi-

bilities, you should contact your nearest au-

thorized service center, call Poulan PRO at

1--800--554--6723, or send e-mail correspon-

dence to

emission.warranty@HCOP--

emission.com

. WARRANTY PERIOD: Any

warranted part which is not scheduled for re-

placement as required maintenance, or which

is scheduled only for regular inspection to the

effect of “repair or replace as necessary” shall

be warranted for 2 years. Any warranted part

which is scheduled for replacement as re-

quired maintenance shall be warranted for the

period of time up to the first scheduled re-

placement point for that part. DIAGNOSIS:

The owner shall not be charged for diagnostic

labor which leads to the determination that a

warranted part is defective if the diagnostic

work is performed at an approved Poulan

PRO servicing center. CONSEQUENTIAL

DAMAGES: Poulan PRO may be liable for

damages to other engine components

caused by the failure of a warranted part still

under warranty. WHAT IS NOT COVERED:

All failures caused by abuse, neglect, or im-

proper maintenance are not covered. ADD--

ON OR MODIFIED PARTS: The use of add--

on or modified parts can be grounds for disal-

lowing a warranty claim. Poulan PRO is not li-

able to cover failures of warranted parts

caused by the use of add--on or modified

parts. HOW TO FILE A CLAIM: If you have

any questions regarding your warranty rights

and responsibilities, you should contact your

nearest autho rized service center, call Pou lan

PRO at 1--800--554--6723, or send e-mail corre-

spondence to emission.warranty@HCOP

emission.com

. WHERE TO GET WARRAN-

TY SERVICE: Warranty services or repairs

shall be provided at all Poulan PRO service

centers. Call: 1--800--554--6723 or send e-mail

correspondence to emission.wa

rranty

@HCOP--emission.com

. MAINTENANCE,

REPLACEMENT AND REPAIR OF EMIS-

SION RELATED PARTS: Any Poulan PRO

approved replacement part used in the per-

formance of any warranty maintenance or re-

pair on emission related parts will be provided

without charge to the owner if the part is under

warranty. EMISSION CONTROL WARRAN-

TY PARTS LIST: Carburetor , air filter (covered

up to maintenance schedule), ignition system:

spark plug (covered up to maintenance sched-

ule), ignition module, muffler including catalyst (if

equipped), fuel tank. MAINTENANCE

STATEMENT: The owner is responsible for

the performance of all required maintenance

as defined in the instruction manual.

The information on the product label indicates which standard your engine is certified.

Example: (Year) EPA and/or CALIFORNIA.

This engine is certified to be emissions compliant for the following use:

Moderate (50 hours)

Intermediate (125 hours)

Extended (300 hours)

Poulan 545186830 User manual

Brand: Poulan

Model: 545186830

Category: Air blowers/dryers

Type: User manual

This manual is also suitable for

Download PDF

report

Poulan 545186830 User manual

This manual is also suitable for

Poulan 545186830 User manual

Related papers

Other documents