Lynx LM15ICER User manual

Lynx
Brand
Lynx
Model
LM15ICER
Category
Ice cube makers
Type
User manual

This manual is also suitable for

MAKE THE MOST OF YOUR
CARE & USE/INSTALLATION
LM15ICER
OUTDOOR CLEAR ICE MACHINE
2
CARE AND USE/INSTALLATION
CONTENTS
Figure 1
Contents:
Warranty registration ..........................................................2
Safety information ...............................................................3
Unpacking your appliance ..................................................3
Installing your appliance ......................................................4
Leveling the appliance ....................................................4
Cabinet clearances .........................................................5
Electrical connection ......................................................5
Installing the drain plumbing ...............................................6
Gravity drain ...................................................................6
Drain pump .....................................................................7
Installing the water supply ...................................................8
Drain System Test .................................................................9
Ice maker operation ..........................................................10
Product dimensions ..........................................................12
Using your Electronic control ............................................14
Starting your appliance ..................................................14
Turning your appliance "ON" or "OFF" ..........................15
Control lock ...................................................................15
Door ajar alarm.............................................................15
Delay start / Vacation mode .........................................15
Error codes ...................................................................16
Options menu ...............................................................16
Normal and eco mode .............................................16
Cleaning your ice machine ..............................................17
Clean reminder ............................................................17
Clean mode ...............................................................17
Care and cleaning .............................................................19
Energy saving tips ............................................................19
Obtaining service .............................................................19
Troubleshooting the ice machine .....................................20
Preparing the ice machine for storage ...........................22
Drain pump removal .........................................................25
The Lynx Story ...................................................27
Warranty Registration:
It is important you send in your warranty registration card
immediately after taking delivery of your appliance or you
can register online at:
www.lynxgrills.com/support/registration
The following information will be required when registering
your appliance.
Model Number
Serial Number
Date of Purchase
Dealer’s name and address
The service/model number and serial number can be found
on the serial plate which is located inside the cabinet on the
left side near the top. (See Figure 1).
XXXXXXXXXXXXXX
XXXXXXXXXXXXXX
XXXXXXXXXXXX
3
CARE AND USE/INSTALLATION
NOTE
NOTE
!
CAUTION
Important Safety Instructions
Warnings and safety instructions appearing in this guide are not meant to cover all possible conditions and situations that
may occur. Common sense, caution, and care must be exercised when installing, maintaining, or operating this appliance.
Recognize Safety Symbols,
Words, and Labels.
CAUTION-Hazards or unsafe practices which could
result in personal injury or property / product damage.
NOTE-Important information to help assure a problem
free installation and operation.
!
WARNING
EXCESSIVE WEIGHT HAZARD
Use two or more people to move product.
Failure to do so can result in personal injury.
Remove Interior Packaging
Your appliance has been packed for shipment with all parts
that could be damaged by movement securely fastened.
Remove internal packing materials and any tape holding
internal components in place. The owners manual is
shipped inside the product in a plastic bag along with the
warranty registration card, and other accessory items.
Important
Keep your carton and packaging until your appliance
has been thoroughly inspected and found to be in good
condition. If there is damage, the packaging will be needed
as proof of damage in transit. Afterwards please dispose of
all items responsibly.
Note to Customer
This merchandise was carefully packed and thoroughly
inspected before leaving our plant. Responsibility for its
safe delivery was assumed by the retailer upon acceptance
of the shipment. Claims for loss or damage sustained in
transit must be made to the retailer.
DO NOT RETURN DAMAGED MERCHANDISE TO THE
MANUFACTURER - FILE THE CLAIM WITH THE
RETAILER.
SAFETY INFORMATION AND UNPACKING YOUR APPLIANCE
!
WARNING
WARNING - You can be killed or seriously injured
if you do not follow these instructions.
!
WARNING
WARNING - Dispose of the plastic bags which can
be a suffocation hazard.
!
WARNING
State of California Proposition 65 Warning:
This product contains one or more chemicals known
to the State of California to cause cancer.
!
WARNING
State of California Proposition 65 Warning:
This product contains one or more chemicals known
to the State of California to cause birth defects or
other reproductive harm.
!
CAUTION
Cabinet Clearance
Ventilation is required from the bottom front of the appliance.
Keep this area open and clear of any obstructions. Adjacent
cabinets and counter top can be installed around the
appliance as long as the front grille remains unobstructed.
Overlay door models with articulated hinges are intended
for built-in applications only.
!
CAUTION
Outdoor Installation
Do not install in a location where the ice machine will
be exposed to direct sun exposure as this may result in
unsatisfactory performance.
!
CAUTION
4
CARE AND USE/INSTALLATION
INSTALLING YOUR APPLIANCE
Select Location
The proper location will ensure peak performance of
your appliance. We recommend a location where the ice
machine will be out of direct sunlight and away from heat
sources. To ensure your product performs to specications,
the recommended installation location temperature range
is from 55 to 90°F (13 to 32°C) for built in ice machines and
55 to 100°F (13 to 38°C) for freestanding ice machines.
Ice machines will not perform correctly in ambient
temperatures less than 55°F (13°C).
Front Grille
Do not obstruct the front grille. The openings within the
front grille allow air to ow through the condenser heat
exchanger. Restrictions to this air ow will result in
increased energy usage, loss of cooling capacity and low
ice production. For this reason it is important this area not
be obstructed and the grille openings kept clean. Lynx Grills
does not recommend the use of a custom made grille as air
ow may be restricted. (See Figure 2).
Leveling Legs
Adjustable legs at the front and rear corners of the
appliance should be set so the unit is rmly positioned on
the oor and level from side to side and front to back. The
overall height of your Lynx appliance may be adjusted
higher (by turning the leveling leg out) and lower (by turning
the leveling leg in). Cabinet height adjustment dimensions
are shown in Table "A".
To adjust the leveling legs, place the appliance on a solid
surface and protect the oor beneath the legs to avoid
scratching the oor. With the assistance of another person,
lean the appliance back to access the front leveling legs.
Raise or lower the legs to the required dimension by turning
the legs. Repeat this process for the rear by tilting the
appliance forward using caution. On a level surface check
the appliance for levelness and adjust accordingly.
The front grille screws may be loosened to raise and
lower the grille to the desired height. When adjustment is
complete tighten the two front grille screws. (See Figure 5).
Rear
Leveling
Legs
Figure 2
Front Leveling
Legs
Front Grille,
keep this area
open.
!
WARNING
WARNING - Help Prevent Tragedies
Child entrapment and suffocation are not problems of
the past. Junked or abandoned refrigerators are still
dangerous - even if they sit out for "just a few hours".
If you are getting rid of your old refrigerator, please
follow the instructions below to help prevent
accidents.
Before you throw away your old refrigerator or
freezer:
• Take off the doors or remove the drawers.
• Leave the shelves in place so children may not
easily climb inside.
If the appliance was shipped, handled, or stored in other
than an upright position for any period of time, allow the
appliance to sit upright for a period of at least 24 hours
before plugging in. This will assure oil returns to the
compressor. Plugging the appliance in immediately may
cause damage to internal parts.
5
CARE AND USE/INSTALLATION
NOTE
Figure 3
Figure 4
Do not remove
ground prong
INSTALLING YOUR APPLIANCE
Front grille
Front grille screw
Figure 5
Electrical Shock Hazard
• Do not use an extension cord with this appliance.
They can be hazardous and can degrade product
performance.
• This appliance should not, under any circumstances,
be installed to an un-grounded electrical supply.
• Do not remove the grounding prong from the power
cord. (See Figure 3).
• Do not use an adapter. (See Figure 4).
• Do not splash or spray water from a hose on the
appliance. Doing so may cause an electrical shock,
which may result in severe injury or death.
!
WARNING
Electrical Connection
A grounded 115 volt, 15 amp dedicated circuit is required.
This product is factory equipped with a power supply cord
that has a three-pronged, grounded plug. It must be plugged
into a mating grounding type receptacle in accordance with
the National Electrical Code and applicable local codes
and ordinances (see Figure 6). If the circuit does not have
a grounding type receptacle, it is the responsibility and
obligation of the customer to provide the proper power
supply. The third ground prong should not, under any
circumstances, be cut or removed.
Figure 6
Ground Fault Circuit Interrupters (GFCI) are prone to
nuisance tripping which will cause the appliance to shut
down. GFCI’s are generally not used on circuits with power
equipment that must run unattended for long periods of
time, unless required to meet local building codes and
ordinances.
Table A
Model
Minimum
Height
Maximum
Height
LM15ICER
33
3
⁄4"
(85.7 cm)
34
3
⁄4"
(88.3 cm)
INSTALLING THE DRAIN PLUMBING
6
CARE AND USE/INSTALLATION
Access
panel
Drain pipe, (not
provided)
Drain tubing, cut
to length and in-
stall in the drain
C
L
C
L
14
7
⁄8"
(37.8 cm)
11
⁄16"
(17mm)
1
1
⁄4"
(3.2 cm)
4
17
⁄32"
(11.5 cm)
21
1
⁄2"
(54.6 cm)
Drain Plumbing
Your ice machine requires drain plumbing. There are 2
variations of ice machines in regards to the installation of
the drain plumbing, without a drain pump (gravity drain),
and with a drain pump.
Figure 9
Figure 8
Drain line coiled
and secured to
the back of the
unit
Uncoil the drain line, route
to an appropriate drain and
cut to the required length
Electrical Shock Hazard
Reasonable care and safe methods should be prac-
ticed. Do NOT work with energized electrical equip-
ment in a wet area. Read and follow the installation
instructions listed in this manual.
!
WARNING
!
CAUTION
Failure to use an adequate drainage system, will result in
surrounding water damage and/or poor ice production.
Figure 7
!
CAUTION
Observe and follow all local building codes
when installing this ice machine and drain
lines.
Water
supply
inlet
Drain access in
bottom of unit
4
3
⁄32"
(10.4 cm)
Sanitary
trap
2
1
⁄4"(5.7 cm)
5
1
⁄8" (13 cm)
Gravity Drain (no drain pump):
The ice machine is shipped with the drain line installed,
coiled and secured to the back of the cabinet as shown
in Figure 7. It can be uncoiled, routed to an appropriate
drain and cut to length as required. Additionally there is the
provision of drain routing through the cut-out in the bottom
of the unit, (see the gray area in Figure 8). A drain can be
installed in this gray area with the drain line cut to a short
length and positioned into the drain as shown in Figure 9,
or if the ice machine is to be built-in, the drain tube could be
routed through a hole in the oor in this gray area to a drain
below.
The gravity drain line must be routed no higher than 6"
(15.2 cm) off the oor to assure proper drainage.
!
CAUTION
7
CARE AND USE/INSTALLATION
INSTALLING THE DRAIN PLUMBING
This drain pump is designed to be installed in Lynx ice
machines only and approved for use with water only.
!
CAUTION
Figure 10
Drain pump
vent tube.
Keep this
open to
assure air
ows freely
as water
enters
the pump
reservoir.
Drain line coiled and
secured to the back of the
cabinet. Uncoil, route to
an appropriate drain and
cut to length.
Optional Drain Pump.
An optional drain pump is available if you have purchased
an ice machine without one and do not have access to a
gravity drain. Installation instructions are provided with the
optional drain pump. Contact Lynx Grills Customer Service
at 888.289.5969 or your dealer for ordering.
Electrical Shock Hazard
Risk of electrical shock or personal injury could occur
due to moving components, if the machine compartment
access cover is removed before unplugging the ice
machine power cord.
!
WARNING
Reverse osmosis, (RO), water, softened water, and de-
ionized water are not recommended as they can adversely
affect the quality and quantity of the ice.
Water
Supply
Line
Clamp and
Screw
Figure 11
Back view of
ice machine
NOTE
!
CAUTION
INSTALLING THE WATER SUPPLY
Compression
tting
Water
supply
line
Water supply
service loop
to shut off
valve
Water valve
inlet
Water Supply
Observe and follow all local building codes when installing
this appliance.
This ice machine must be connected to a potable cold
water supply line. delivering water pressure between a
minimum of 20 psi and a maximum of 120 psi.
Use
1
⁄4" copper tubing for your water supply which is available
at any local hardware or plumbing supply store. Route the
1
⁄4" copper tubing to suit your installation being sure not
to kink the tubing. Purchase enough copper tubing length
to allow a coil to be formed behind the unit for a "service
loop" which will allow the appliance to be pulled out from
the installation for servicing or cleaning. (See Figure 11).
Connect the copper tubing to the "top side" of a cold water
pipe to prevent the ice-maker from plugging with sediment.
A shutoff valve is recommended on the water supply line to
ease servicing the appliance. NOTE: A SELF-PIERCING
TYPE VALVE IS NOT RECOMMENDED as they are prone
to clogging with sediment which will create pressure drop
reducing the water supply to the unit.
Connect the copper tubing water supply to the water valve
inlet with a 1/4" compression nut tting.
IMPORTANT: Secure the water supply line to the back of
the cabinet with the screw and strain relief clamp provided
in the corner of the back panel. (See Figure 11).
Make certain all connections are watertight after
installation. Form the tubing so that it will not vibrate
against the cabinet body or kink when your appliance is
moved in and out of position.
This ice machine is designed to make clear ice from the
majority of water sources on a daily basis. If your results
are unsatisfactory, your water may need to be ltered or
treated. A water specialist can recommend proper water
treatment.
!
CAUTION
To prevent water leaks:
• The water line tting is to be used with copper tubing
only. Do not use with plastic tubing.
• Do not use any thread sealers on this water line tting.
8
CARE AND USE/INSTALLATION
9
CARE AND USE/INSTALLATION
DRAIN SYSTEM TEST
Procedure for Testing Drain System
(both gravity and drain pump models)
Drain pump models have a safety feature that will interrupt power to the unit if a high-limit condition occurs to prevent
ooding. This safety feature can be initiated by a restriction in the drain system and will continue until high-limit condition
is corrected, at which time power will be restored to the unit. Power interruption can be detected when no icons are
visible in the display area of the user interface (Figure 12). Once power is returned, a startup chime will sound followed
by a self-test, and "OFF" should be visible in the display area.
Drain pump vent
tube. Keep this
open to assure
air ows freely as
water enters the
pump reservoir.
Figure 14: Location of vent tube.
Figure 13: Example of an open drain.
Sanitary trap
!
CAUTION
hours
ICE
1 4 6 8
OFF CLEAN
DOOR
ECO
days
On/off Menu Delay timer Lock
Once the drain line is plumbed, perform the following:
1. Plug the ice machine into 115v power supply.
2. Place unit in the nal installation location.
3. Turn the unit off via the user interface (display will indicate “OFF”). The drain pump will still be operational during off
mode if the unit has one.
4. Slowly pour 3-qts of water into the ice storage bin. All water should drain completely.
5. If water drains fully and without power interruption, the drain system has been successfully tested and further
installation of the ice machine can be continued.
6. If the water does not drain or a power interrupt occurs, check the following:
a. There are no kinks or restrictions in the drain line. (Note: Drain line needs to be cut to the required length and any
excess tubing should be removed to prevent possible restrictions).
b. Your drain line is plumbed into an open drain (Figure 13).
c. The vent tube on the back of the unit is open (Figure 14).
Figure 12: User interface display during power interruption.
7. After checking the above requirements, repeat step 4 and verify the water drains completely without power
interruption. If problems persist call a qualied service technician and/or plumber.
Air gap
between
end of
drain line
and top of
water level
10
CARE AND USE/INSTALLATION
The Ice Making Process
Your ice machine is unique in how it forms ice with fraction-
al freezing to form a slab of ice that is clear and has less
dissolved solids than the water it is produced from. This is
accomplished by running water over the cold evaporator
plate (see Figure 16) which gradually freezes the water to
produce the ice slab. Pure water freezes rst, leaving the
dissolved solids in the residual reservoir water to provide
clear ice.
Figure 16
When the ice slab reaches the correct thickness, the ice
sheet is released and slides onto the grid cutter (see Figure
16). Here, the ice slab is cut into squares by the grid cut-
ter’s heated wires (see Figure 19). The water containing
the dissolved minerals is drained after each freezing cycle.
Fresh water enters the machine for the next ice making
cycle.
Figure 18
Figure 17
OPERATION OF THE ICE MACHINE
Water
reservoir
Evaporator
Circulation
Pump
Reservoir
drain plug
Front
panel
Bin Level
Sensor
Ice
Deector
Grid Cutter
Water distributor
11
CARE AND USE/INSTALLATION
The bin level sensor is located in the ice bin, it senses
when the ice supply is low or full and starts or stops the ice
making process accordingly.
If the water supply is turned off to the ice machine be sure
to set the electronic control to the “OFF” position or remove
power to the unit.
New Sounds
The ice machine will make sounds that are different than
your household refrigerator. Because these sounds are
new to you they may be of a concern but are most likely
normal. The ice production process will make noises that
are not typical in a refrigeration product, ice falling onto
hard surfaces, water cascading across the evaporator, and
valves opening and closing. Following are some of the
sounds that you may hear:
A buzzing sound will be heard when the water valve
opens to ll the water reservoir.
A rattling noise which could be water owing through the
water line.
A splashing sound when water is owing over the
evaporator plate and into the water reservoir.
A "thud" when the ice slab is released from the
evaporator plate and slides onto the grid cutter.
"Clicks" when the cubes fall into the ice storage bin.
A gurgling sound which is refrigerant owing in the ice
machine.
An air noise from the condenser fan.
Ice Production
In normal mode the ice machine will produce up to 39
pounds (17.7 kg) of clear ice in a 24-hour period when
installed in a 72°F ambient with a 55°F water supply. In
"ECO" mode (see page 16) the ice machine will produce up
to 29 pounds (13.2 kg) of clear ice in the 24 hour period.
“Initial” ice production and ice accumulated in the storage
bin will vary signicantly. This is normal. During the rst
24-hours of operation the unit will produce up to 39 lbs of
ice at the above ambient and water temperature conditions,
but when starting with an empty ice storage bin, the storage
bin may only accumulate up to 18 lbs of ice. By design,
the ice storage bin is maintained at a temperature slightly
above freezing to allow the stored ice to slowly melt, to
preserve the ice quality and clarity and assure a constant
supply of fresh ice. As ice is accumulated in the bin, the ice
production rate will overcome the ice melt and the storage
bin will ll to capacity.
NOTE
NOTE
OPERATION OF ICE MACHINE
The ice machine will keep producing ice until the ice
machine’s bin is full and will restart automatically when
ice needs to be replenished in the bin. The ice bin is
not refrigerated, and some melting will occur by design
to preserve the ice quality and clarity. Allow your ice
machine to run for 24-48 hours to accumulate ice in the ice
machine’s bin.
Figure 19
12
CARE AND USE/INSTALLATION
PRODUCT DIMENSIONS
ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS
MODEL "A" "B" "C" "D" "E" "F" "G" "H" "J"
LM15ICER
15"
(38.1 cm)
**34" to 35"
(86.4 to 88.9 cm)
24"
(61 cm)
14
7
⁄8"
(37.8 cm)
33
3
⁄4" to 34
3
⁄4"
(85.7 to 88.3 cm)
23
5
⁄8"
(60 cm)
25
9
⁄16"
(64.9 cm)
37
13
⁄32"
(95 cm)
16
11
⁄16"
(42.4 cm)
"A"
"B"
"C"
"D"
"E"
Figure 20
Figure 20a
Figure 21
If necessary to gain clearance inside the rough-in
opening a hole can be cut through the adjacent cabi-
net and the power cord routed through this hole to a
power outlet. Another way to increase the available
opening depth is to recess the power outlet into the
rear wall to gain the thickness of the power cord plug.
Not all recessed outlet boxes will work for this applica-
tion as they are too narrow, but a recessed outlet box
equivalent to Arlington #DVFR1W is recommended for
this application, (see Figure 21).
13
CARE AND USE/INSTALLATION
PRODUCT DIMENSIONS
PRODUCT DATA
MODEL
ELECTRICAL
REQUIREMENTS #
PRODUCT
WEIGHT
LM15ICER 115V/60Hz/15A
105 lbs
(47.7 kg)
** Minimum rough-in opening required is to be larger than
the adjusted height of the cabinet.
# A grounded 15 amp dedicated circuit is required. Follow
all local building codes when installing electrical and
appliance.
"F"
"D"
"E"
"H"
"J"
"G"
CL
Water
inlet
4
7
⁄8"
(12.4 cm)
1
1
⁄4"
(3.2 cm)
CL Gravity
drain
Figure 22
(S) solid
door shown
21
1
⁄2"
(54.6cm)
6
15
⁄16"
(17.6 cm)
14
CARE AND USE/INSTALLATION
USING YOUR ELECTRONIC CONTROL
Starting your clear ice machine:
Plug the ice machine into a 115 volt wall outlet,
(see page 5 for electrical information). Your
appliance is shipped from the factory in the "ICE" mode
and will begin start-up of ice production after the start-up
routine.
Upon applying power to the unit, or after a power
interruption, the Ice machine will perform a self-test,
followed by a harvest cycle to clear any in-process ice
production. This start-up routine, (“after power is applied
to the unit”), takes approximately 13 minutes to complete
before an ice production cycle starts.
If the appliance does not start, conrm the wall outlet has
power, and the control is in the "ICE" mode, (see Options
section below). Do not start the ice machine in "ECO"
mode. "ECO" mode should only be used after there is a full
bin of ice.
hours
ICE
1 4 6 8
OFF CLEAN
DOOR
ECO
days
"ON/OFF" icon : used for turning the appli-
ance on and off.
"MENU" icon : used to access optional func-
tions in the user interface.
"Clock" icon : used to enter the Delay start/
vacation mode.
"LOCK" icon : used to lock out functions in
the user interface.
Display icons:
ICE
1
4
6
8
hours
days
Display area text:
ICE
OFF
DOOR
CLEAN
ECO
Signies the appliance is on and producing
ice.
Signies the appliance is off
Signies a door ajar alarm condition.
Cleaning is recommended or the appliance
is in the clean mode.
Signies the appliance is in economical ice
production mode.
Figure 23
User interface display
On/off Menu Display area Delay timer Lock
When lit, this signies the delay start/vacation mode
is operational.
Hours or days will be lit
Hours or days timer is set for
Delay start/Vacation mode:
The control display is covered with a clear plastic protective
lm. This lm may be removed by carefully lifting at a
corner.
NOTE
15
CARE AND USE/INSTALLATION
Turning your ice machine On and Off:
If your appliance is on, "ICE" will be displayed.
To turn the appliance off, push and hold the "ON/
OFF" icon for 3-seconds. The display will show
"OFF" .
The drain pump (if equipped) and the interior light
will still be functioning during the OFF mode. To
turn the appliance back on, press and hold the "ON/OFF"
icon for 3-seconds, the display will show "ICE".
ICE
ICE
OFF
USING YOUR ELECTRONIC CONTROL
Control Lock:
The user interface can be locked to avoid uninten-
tional changes from things like cleaning. To lock
the appliance, push and hold the "LOCK" icon for
5-seconds. The "LOCK" icon will ash 3 times, then change
to steady back-lit. To unlock the user interface, press and
hold the "LOCK" icon for 5-seconds, and the back-light will
turn off.
NOTE
NOTE
The "LOCK" icon is the only active key in this mode. If other
icons are pressed while in the lock mode the "LOCK" icon
will ash 3 times, and an audible tone will sound, to remind
the user the appliance is in the lock mode.
When turned off, the ice machine will complete its
current ice production cycle then shut off.
Turning the ice machine "OFF" will only terminate the
ice production, it does not remove power from the ap-
pliance. Always unplug the power cord from the wall
outlet before servicing the unit.
!
WARNING
Door ajar alarm:
If the door is open, or not closed properly for 5
minutes the "DOOR" indicator will illuminate and
ash and an audible tone will sound. The audible
alarm can be muted by pressing the "Lock" keypad.
This alarm condition can be reset by closing the
door or momentarily pressing the "ON/OFF" icon,
(i.e.-if you are cleaning the storage compartment, etc.). The
alarm will recur in 5 minutes if the alarm condition persists.
DOOR
Delay start/Vacation mode:
Your ice machine is equipped with a delay start function.
This feature can be used to temporarily shut the appliance
off for 1, 4, 6, or 8 hours or days. Upon completion of the
selected delay period, the appliance will resume operation.
This is ideal for temporarily stopping ice machine noises or
to save water and electricity if you are away from home but
want fresh ice upon your return.
To enter the delay start mode, press the "CLOCK"
icon while the appliance is in "ICE" mode. This will
delay the next harvest by the time displayed. Each
additional press of the "CLOCK" icon will add time,
from 1, 4, 6, or 8 hours, to 1, 4, 6, or 8 days. The next
press after 8 days will leave delay set
mode. After the desired time has been
selected, press the "ON/OFF" icon for 2 seconds
to accept, your unit will shut off and a clock icon
and your selected time will be displayed. When the
selected time has elapsed, normal ice production will
resume.
To cancel the delayed start, press and
hold the "ON/OFF" icon until the appli-
ance enters OFF, then press and hold
the "ON/OFF" icon again until the appli-
ance enters "ICE" mode.
1 4 6 8
hours
days
ICE
OFF
Error Codes
Error Displayed Code Error Description Action to Take
Bin Sensor error
"OFF" will ash continuously in 1
second intervals in the display. No
audible alarm will sound.
Failed temperature sensor. Machine operation will imme-
diately enter an OFF state.
Call service to have the
temperature sensor replaced.
System Sensor error
"ICE" will ash continuously in
the display. No audible alarm will
sound.
Failed condenser temperature sensor. Machine opera-
tion will continue but ice production cycle will not adapt to
varying ambient conditions, so ice quality may vary.
Call service to have the
temperature sensor replaced.
Communication error
Continual ashing of all indicators
on the display.
Loss of communication between the main board and the
user interface.
Call service to have a
diagnostic check.
Error codes:
The ice machine is monitored continuously. Any OPEN or
SHORTED circuit condition with a temperature sensor or
miscommunications between the control and user interface
will initiate an ERROR CODE as listed below:
16
CARE AND USE/INSTALLATION
Options menu:
Normal and ECO mode:
Your ice machine comes with an optional "ECO" mode.
This new feature allows you to tailor ice production to a
conservative rate, saving approximately 25% energy and
30% water from routine operation. While in this mode
ice production will slow and the appliance will use less
water and electricity. "ECO" mode should only be initiated
after there is a full bin of ice. To enter "ECO" mode do the
following:
• Press the "MENU" icon twice and the green
"ECO" will ash.
• Press and hold the "ON/OFF" icon until the
green "ECO" stops ashing and remains
illuminated.
• To return to the standard operating rate press the
"MENU" icon twice, the ECO will turn off and the
"ICE" will be ashing. Press and hold the "ON/
OFF" icon until the "ICE" stops ashing and
remains illuminated.
ICE
ECO
USING YOUR ELECTRONIC CONTROL
17
CARE AND USE/INSTALLATION
!
CAUTION
CLEANING YOUR ICE MACHINE
Forcing ice through the grid cutter will break the grid cutter
wires.
!
CAUTION
Remove all ice
from the evaporator
plate and grid cutter
area that is not
embedded in wires
Figure 24
Figure 25
Clean mode:
To ensure maximum performance and ice quality, it is
recommended to clean your ice machine once every six
months. This simple cleaning routine will also ensure water
and energy use continues at optimum efciency.
Clean reminder:
A "CLEAN" reminder will occur every 6 months
to remind you that it may be time to clean your
appliance. Over time mineral build up on the cold
evaporator plate can occur which can adversely
affect the quality of your ice. This build-up is
dependent on your water source and usage. Normal
ice production will continue while the "CLEAN" reminder
is displayed. You may clear the "CLEAN" reminder at any
time by momentarily pressing the "ON/OFF" icon. When
reset, the "CLEAN" reminder will reset and not occur for
another 6 months. If you choose to clean the appliance at
this time, see the options menu section below.
CLEAN
NOTE
Homes with poor water quality or high clear ice usage
might require more frequent cleaning.
To clean your ice machine you will need to purchase a
"nickel safe" ice maker cleaner. Cleaner can be obtained by
contacting Lynx Grills Customer Service at 888.289.5969.
Once you have your cleaner:
Turn the ice machine off by pressing and holding
the "ON/OFF" icon for 3 seconds. "OFF" will be
displayed on the control.
Remove all ice from the ice bin (see Figure 27).
Drain the water from the water reservoir by removing the
black plug from the bottom of the fresh water reservoir (see
Figure 28). After the water is drained, replace the plug in
the bottom of the reservoir.
Allow all of the ice to fall from the evaporator plate
and remove any ice from the grid cutter. If there is ice
embedded in the grid cutter wires, wait for it to melt and
fall out. Do not try to remove ice that is embedded in
the grid cutter wires as that may break the wires. (See
Figures 21 and 22).
OFF
18
CARE AND USE/INSTALLATION
CLEANING YOUR ICE MACHINE
Figure 27
Figure 26
Remove all of
the ice from
the ice bin
Figure 28
Remove the
black reservoir
drain plug from
the bottom of
the reservoir.
Figure 29
Turn the ice machine back on by pressing and
holding the "ON/OFF" icon for 3 seconds. The
display will indicate "ICE" mode. Press and hold the
"MENU" icon until a ashing "CLEAN" is dis-
played. Press the "ON/OFF" icon until "CLEAN"
stops ashing. Your ice machine will now enter
the clean cycle.
The clean and rinse cycle will take about 49 min-
utes.
After the clean cycle is complete the ice machine
will return to the "OFF" position.
After the cleaning cycle is completed, verify that all build-up
has been removed. If not repeat the clean cycle procedure.
ICE
CLEAN
OFF
Refer to your cleaning solution instructions to determine
the proper amount of cleaning solution to add based on
2 quarts (1.9 liters) of water. Lift fascia door up to access
evaporator plate (See Figure 29). Pour the cleaning
solution slowly on the evaporator plate so it ows down into
the fresh water reservoir. (See Figure 30).
Figure 28b
Splash shield
brackets
Replace the splash shield if removed.
Pour cleaning solution slowly
onto the front edge of evaporator
plate behind the grid cutter.
Figure 30
Evaporator
plate
Grid cutter
Splash shield
Lift fascia door up to
access evaporator plate
19
CARE AND USE/INSTALLATION
!
CAUTION
CARE AND CLEANING AND ENERGY SAVING TIPS
OBTAINING SERVICE
Front Grille
Be sure that nothing obstructs the required air ow openings
in front of the cabinet. At least once or twice a year, brush or
vacuum lint and dirt from the front grille area (see page 4).
SHOCK HAZARD: Disconnect electrical power from the
appliance before cleaning with soap and water.
Cabinet
The painted cabinet can be washed with either a mild soap
and water and thoroughly rinsed with clear water. NEVER
use abrasive scouring cleaners.
Cleaning
Routine cleaning of the stainless steel surfaces will serve
to greatly extend the life of your product by removing
contaminants. This is especially important in coastal areas
which can expose the stainless to sever contaminants such
as halide salts (sodium chloride).
It is strongly recommended to periodically inspect and
thoroughly clean crevices, weld points, under gaskets,
rivets, bolt heads, and any locations where small amounts
of liquid could collect, become stagnant, and concentrate
contaminants. Additionally, any mounting hardware that is
showing signs of corrosion should be replaced.
Interior
Wash interior compartment with mild soap and water. Do
NOT use an abrasive cleaner, solvent, polish cleaner, undi-
luted detergent or chlorine based cleaners.
Care of Appliance
1. Avoid leaning on the door, you may bend the door
hinges or tip the appliance.
2. Exercise caution when sweeping, vacuuming or
mopping near the front of the appliance. Damage to the
grille can occur.
3. Periodically clean the interior of the appliance as
needed.
4. Periodically check and/or clean the front grille as
needed.
In the Event of a Power Failure
If a power failure occurs, try to correct it as soon as
possible. Minimize the number of door openings while the
power is off so as not to adversely affect the appliance's
temperature.
Light assembly replacement
All models use LED lamps to illuminate the interior of the
appliance. This component is very reliable, but should
one fail, contact the Lynx Grills Customer Service at
888.289.5969 for replacement of the LED.
Energy Saving Tips
The following suggestions will minimize the cost of
operating your ice machine appliance.
1. Do not install your appliance next to a hot appliance,
(stove, dishwasher, etc.). heating air duct, or other heat
sources.
2. Install product out of direct sunlight.
3. Assure the front grille vents at front of the ice machine
beneath the door are not obstructed and kept clean to
allow ventilation for the refrigeration system to expel
heat.
4. Plug your appliance into a dedicated power circuit. (Not
shared with other appliances).
5. Minimize door openings and duration of door openings.
6. Set the control to the “off” position if accessing the
interior to spot clean or remove large quantities of ice
requires the door to be open for an extended period of
time.
7. Use ECO mode if maximum ice production quantities
are not required.
8. Use the delay start function if the ice machine will not
be used for long periods of time.
If Service is Required:
• If the product is within the rst year warranty period
please contact your dealer or call Lynx Grills Customer
Service at 888.289.5969 for directions on how to obtain
warranty coverage in your area.
• If the product is outside the rst year warranty period,
Lynx Grills Customer Service can provide recommen-
dations of service centers in your area.
• In all correspondence regarding service, be sure to
give the service number, serial number, and proof of
purchase.
• Try to have information or description of nature of the
problem, how long the appliance has been running, the
room temperature, and any additional information that
may be helpful in quickly solving the problem.
• Table "C" is provided for recording pertinent information
regarding your product for future reference.
For Your Records
Date of Purchase
Dealer’s name
Dealer’s Address
Dealer’s City
Dealer’s State
Dealer’s Zip Code
Appliance Serial Number
Appliance Service Number
Date Warranty Card Sent (Must be
within 10 days of purchase).
Table C
20
CARE AND USE/INSTALLATION
• Never attempt to repair or perform maintenance on
the appliance until the main electrical power has been
disconnected. Turning the appliance control "OFF"
does not remove electrical power from the unit's wiring.
• Replace all parts and panels before operating.
!
WARNING
Electrocution Hazard
TROUBLESHOOTING THE ICE MACHINE
Before You Call for Service
If the appliance appears to be malfunctioning, read through
this manual rst. If the problem persists, check the trouble-
shooting guide below. Locate the problem in the guide and
refer to the cause and its remedy before calling for service.
The problem may be something very simple that can be
solved without a service call. However, it may be required
to contact your dealer or a qualied service technician.
Troubleshooting guide:
Ice Machine Operation
Ice machine does not operate
Is the ice machine’s power cord plugged in? Plug the
power cord into a grounded 3 prong outlet.
Is the electronic control showing the "ICE" position?
Check the control to be sure it is in the "ICE" position.
Is a fuse blown or a circuit breaker been tripped? Re-
place a blown fuse or reset a tripped circuit breaker.
Is the temperature of the room cooler than it normally
is? The minimum room temperature is 55°F (13°C). The
bin thermistor may be sensing the room temperature and
shut off before the bin is full of ice. If the room temperature
remains low the ice machine may not restart.
Is there a drain pump in the ice machine? The drain
pump is designed to temporarily shut the unit off when
large quantities of water create a high-limit condition. Wait
a few minutes as the drain pump will continue to operate
to dispose of the excess water. If there is still water in the
ice bin check the drain pump vent line and drain line for
obstructions or kinking.
The ice machine is noisy
Many sounds of an ice machine are different than your
household refrigerator. This subject is discussed on page
11, but check the following:
Do you hear water being circulated in the ice ma-
chine? This is a normal sound as water is added once
every ice making cycle.
Is there a “whoosing” sound? Make sure water is get-
ting to the ice machine. Also check to make sure the drain
plug is fully seated in the water reservoir.
Is there an ice slab caught between the evaporator
plate and the grid cutter? First check to see if the ice
machine is level. If the ice machine is level run a cleaning
cycle.
Ice Production
Little or no ice production from the ice machine
Is the electronic control set to the "ICE" position?
Check the control to be sure it is in the "ICE" position.
Is water getting to the ice machine? Make sure nothing
is restricting the water supply such as a closed water valve
or a blown fuse or tripped circuit breaker, or a kinked sup-
ply line, or low water pressure.
Has the ice machine just been started? A typical ice
production cycle can take up to 1
1
⁄2 hours. Initial start up
cycles can take longer. Check the ice machine after 24
hours for ice accumulation in the bin.
Is the reservoir drain plug in place? Check that the
reservoir drain plug is properly seated.
Is the water distributor tube restricted? Run a cleaning
cycle to clean the ice machine. Also check any lters to
make sure they are not restricted.
Is the condenser fan air ow restricted? Make sure the
grille in the front of the ice machine is open for proper air
circulation.
Is the room and/or water temperature to warm? Move
the ice machine to an area where the ambient temperature
is below 90°F (32°C) for built-in ice machines or below
100°F (38°C) for freestanding ice machines. The ice ma-
chine should not be placed next to a heat source such as
an oven. Check the cold water connection.
Is there scale build up in the ice machine? If there is
scale build up on the evaporator, the ice machine needs to
be cleaned. See “Cleaning the Ice machine”.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29

Lynx LM15ICER User manual

Lynx
Brand
Lynx
Model
LM15ICER
Category
Ice cube makers
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents