Cartoni Sport 200 User manual

Brand: Cartoni

Model: Sport 200

Type: User manual

Cartoni Sport 200 is a professional camera support designed for durability and safety. With a payload capacity of up to 441 lbs, it can handle heavy camera setups. The tripod's height can be adjusted from 22 to 45 inches, making it suitable for various shooting scenarios. The mid-level spreader and extendable legs with engraved height references ensure stability and precise positioning. The flat upper base and level bubble aid in achieving accurate leveling. Optional accessories like the HD Ground Spreader and 4 Ways Leveller enhance its versatility.

PROFESSIONAL CAMERA SUPPORT

USER’S MANUAL

& Maintenance

Thank you for choosing the Sport 200 tripod manufactured by CARTONI.

The Sport 200 is designed and built using state-of-art technologies and

procedures in order to guarantee maximum reliability over me, as well as

total safety for its users.

! In order to properly and safely use the Sport 200 tripod

read this manual and follow the instrucons.

! All back-up material, and this manual in parcular,

should be stored in a safe place for future reference.

! This publicaon may not be reproduced in full or in part,

or memorized, transmied or translated into any com-

mon or computer language, in any form or by any elec-

tronic, mechanical, magnec, opcal, chemical, manual or

other means without the express authorizaon in wring

of CARTONI

! CARTONI holds the right to revise or change this pub-

licaon without any prior advice to any person or orga-

nizaon.

DISCLAIMER

CARTONI ceres that the informaon contained in this manual is correct at the

me of prinng. CARTONI reserves the right to update or change any specica-

on, design and/ or funconality of the product and the relevant informaon at

any me and without no- caon. Updates in the documentaon will be incorpo-

rated in the new release of the same. For the updated version please consult the

latest release on our website www.cartoni.com.

DECLARATION OF CONFORMITY

CARTONI declares that this product has been manufactured in accordance with

standards ISO 9001:2015 and complies with the EC Direcve 2001/95/CE.

Index

1. INTRODUCTION 5

1.1 WARRANTY 5

1.2 AUTHORIZED PERSONNEL 6

2. TECHNICAL SPECIFICATIONS 7

2.1 COMPATIBLE EQUIPMENT 8

2.2 SPECIFICATIONS 8

2.3 OPTIONAL ACCESSORIES 9

3. INSTALLATION AND SETTINGS 9

3.1 SETTING THE SPORT 200 9

3.2 MOUNTING A CAMERA SUPPORT HEAD 12

4. SAFETY PRECAUTIONS 12

5. DISASSEMBLING AND STORAGE 13

6. SERVICE 14

6.1 ROUTINE MAINTENANCE 14

6.2 EXTRA MAINTENANCE AND SPARE PARTS 14

6.5 DECOMMISIONING 15

CARTONI ®

Manual Version: 1.0

IT IS HEREBY CERTIFIED THAT THE QUALITY MANAGEMENT SYSTEM OF

IAF:17

IAF:29

19714/09/S

CARTONI S.P.A.

VIA DI PORTONACCIO, 33/B 00159 ROMA (RM) ITALIA

DESIGN, MANUFACTURE AND POST-SALE ASSISTANCE OF PROFESSIONAL BROADCAST AND FILM EQUIPMENT.

MARKETING OF PROFESSIONAL BROADCAST AND FILM ACCESSORIES AND PRODUCTS AS LOCAL

AGENCY/REPRESENTATIVE

PROGETTAZIONE, FABBRICAZIONE ED ASSISTENZA POST-VENDITA DI PRODOTTI PER LA CINEMATOGRAFIA E LA

TELEVISIONE PROFESSIONALE. COMMERCIALIZZAZIONE DI PRODOTTI ED ACCESSORI IN CONCESSIONE PER LA

CINEMATOGRAFIA E LA TELEVISIONE PROFESSIONALE

Per informazioni sulla validità

del certificato, visitare il sito

www.rina.org

For information concerning

validity of the certificate, you

can visit the site

www.rina.org

CCEERRTTIIFFIICCAATTEE NNoo..

CERTIFICATO N.

SI CERTIFICA CHE IL SISTEMA DI GESTIONE PER LA QUALITÀ DI

PER I SEGUENTI CAMPI DI ATTIVITÀ / FOR THE FOLLOWING FIELD(S) OF ACTIVITIES

NELLE SEGUENTI UNITÀ OPERATIVE / IN THE FOLLOWING OPERATIONAL UNITS

L'uso e la validità del presente certificato sono soggetti al rispetto del documento RINA: Regolamento per la Certificazione di Sistemi di Gestione per la Qualità

La validità del presente certificato è subordinata a sorveglianza periodica annuale / semestrale ed al riesame completo del sistema di gestione con periodicità triennale

The validity of this certificate is dependent on an annual / six monthly audit and on a complete review, every three years, of the management system

È CONFORME ALLA NORMA / IS IN COMPLIANCE WITH THE STANDARD

Per i requisiti della norma non

applicabili al campo di applicazione

del sistema di gestione

dell'organizzazione, riferirsi alle

informazioni documentate relative.

Reference is to be made to the

relevant documented information

for the requirements of the

standard that cannot be applied to

the Organization's management

system scope

ISO 9001:2015

The use and validity of this certificate are subject to compliance with the RINA document : Rules for the certification of Quality Management Systems

12.06.2009

24.05.2021

CISQ è la Federazione Italiana di Organismi di

Certificazione dei sistemi di gestione aziendale

CISQ is the Italian Federation of

management system Certification Bodies

Prima emissione

First Issue

Data revisione

Revision date

RINA Services S.p.A.

Data scadenza

Expiry Date 02.06.2024

Via Corsica 12 - 16128 Genova Italy

Data decisione di rinnovo

Renewal decision date 24.05.2021

Amilcare Rini

Rome Management System

Certification, Head

Membro degli Accordi di Mutuo

Riconoscimento EA, IAF e ILAC

Signatory of EA, IAF and ILAC

Mutual Recognition Agreements

SGQ N° 002 A

1. IntroductIon

The correct and safe use of this tripod is only guaranteed if it is used in

accordance with the following manual and other documentaon that ac-

companies the Sport 200 tripod. It is therefore essenal to read all the

documentaon carefully and to keep it in a safe place.

It is necessary to always make sure that all the operators have completely

read and understood the instrucons. CARTONI accepts no responsibility

for damage to persons and/or property consequence to the improper use

of the tripod.

Do not remove or deface any label, indicaon and warning axed to the

tripod.

CARTONI declines al responsibility for the failure to observe the standards

of safety and prevenon detailed in the various secons of this manual and

for injuries caused due to improper use.

Any modicaon to the tripod must have prior authorizaon by CARTONI

and it is strictly forbidden to use the Sport 200 in any other way than indi-

cated.

All the standard maintenance operaons (maintenance, repairs, cleaning

and adjustments) should be carried out by competent personnel as pre-

scribed in the manual.

1.1 Warranty

The Sport 200 tripod is covered by a warranty against manufacturing de-

fects for 2 years from the date of shipment.

The warranty covers replacement of any defecve part and the labour re-

quired excluding transport/duty costs.

In the case of replacement of single parts, these can be supplied free of

charge by CARTONI, but the owner will bear the cost of transport/duty

charges for the parts.

The warranty is only valid if the tripod has been used properly as outlined

in the manufacturer’s instrucons and has not been exposed to any mis-

handling. The warranty will be immediately invalid if modicaons and/or

repairs are carried out by unauthorized persons otherwise authorized by

CARTONI.

Components subject to wear and tear are not covered by warranty.

The warranty is also invalidated by one of the following events:

• Failure to comply with payment condions

• Failure to carry out appropriate maintenance

• Removal or mistreatment of marks and/or labels containing data

and technical specicaon

CARTONI accepts no responsibility for damage to the tripod caused by im-

proper use or the malfuncon of other equipment connected to the Cam-

era support.

In any case, the warranty only covers tripod damage and/or malfuncons

and does not entle the purchaser/owner to claim any damages for loss of

producon me due to assumed or proven damage caused by and/or con-

nected to the tripod itself.

1.2 authorIzed personnel

Extraordinary maintenance and repairs to the Sport 200 can only be carried

out by competent persons who are either employed, trained or authorized

by CARTONI in wring.

Any informaon regarding repair/maintenance service staons can be ob-

tained from CARTONI.

2. technIcal specIfIcatIons

Flat upper base

Level bubble

Central brace knob

Safety pin & housing

Mid-level spreader

Leg clamp knob

Orientable foot

Extendable leg

Tripod height reference

Mid-level spreader knob

Tripod leg

4 Peg holes

2.1 compatIble equIpment

The equipment used with the Sport 200 tripod should comply the

following specicaons:

• Maximum weight: 200 Kg (441 lbs.)

• Weight distribuon must verify that the centre of gravity (CG) of the

mounted elements stays well inside the opened tripod base diameter.

! CARTONI accepts no responsibility for malfuncons or

damage to persons or equipment, materials, etc. when

used with equipment other than those indicated in the

manual.

! DANGER: it is strictly forbidden to climb on the tripod.

2.2 specIfIcatIons

Payload (up to) 200 Kg 441 lbs

Total weight 10,5 Kg 23 lbs

Minimum height 57 cm 22 in.

Maximum height 115 cm 45 in.

Folded height 72 cm 28 in.

Folded width 25 cm 10 in.

Operaonal temperature -20°C / +60°C -4°F / +140°F

2.3 optIonal accessorIes

3. InstallatIon and settIngs

Prior to seng-up, please check the state of packaging for its integrity on

arrival, and also make sure that none of the components show signs of

impact. If any such damage occurs CARTONI should be informed immedi-

ately.

If the Sport 200 is to be forwarded elsewhere, it should be carefully packed

with care not to damage any of the components.

3.1 settIng the sport 200

Please set the CARTONI Sport 200 tripod as follows.

Release the central brace knob (3) and completely spread the tripod; then

lock in place with the same central brace knob (3).

4 Ways Leveller (AH896) Dolly HD (D736)

HD Ground Spreader (S732/HD)

! On open posion, the mid-level spreader remains in an-

gled posion; do not force to total horizontal posion.

To set the tripod height, remove the safety pins (4) from their safety hous-

ings (4) or if inserted, release the three leg clamp knobs (6), li the tripod

pulling up the upper at base (1) ll the desired height, then lock in place the

three extendable legs (8) with the three leg clamp knobs (6); the extendable

legs (8) have engraved height reference numbers (9) to set the height in the

three tripod legs uniformely. Finally, secure the tripod posion inserng the

three safety pins (4) in the upper holes on the extendable legs (8).

❹

To obtain horizontal posion for the upper at base (1), release the extend-

able leg clamp knobs (6), check the level bubble (2) to horizontal posion

and lock in place all the legs with the three leg clamp knobs (6).

To widen the three tripod legs (11), release the three mid-level spreader

knobs (10), extend the mid-level spreader (5) and lock in place all the legs

with the three mid-level spreader knobs (10); for beer stability always ex-

tend the mid-level spreader (14) at maximum seng.

The orientable foot (7) has a recessed spike which can be extracted by ro-

tang the orientable foot. The spike extracon is suitable for so terrains

to ensure a beer grip.

❹

❼

Each foot has 4 holes for oponal Pegs

(12).

To install a dolly or a oor spreader, bend

the three feet (7) outwards in order to

access the tripod hooking bar.

3.2 mountIng a camera support head

The tripod at upper base (1) has a standard Mitchell base aachment and

4 holes for Vinten standard aachment; it accomodates a variety of camera

support heads and other devices.

4. safety precautIons

! The tripod has been designed to respect ergonomic

principles to allow operators to use it without any physi-

cal exeron. This includes working condions with min-

imum strain, movements, frequency of rounes to avoid

any physical and psycological discomfort.

! Tripod operators must take the utmost care to avoid

any acon that might endanger themselves, the tripod or

others.

❼

⓬

Anyone who operates the tripod must be throughly trained in the correct

methods of use and its safety features.

The tripod must be used according to the instrucons indicated in this

manual.

5. dIsassemblIng and storage

! Before folding the tripod ensure that the load has been

removed.

To fold the tripod please proceed as follows. Remove the 3 safety pins (4)

from the legs (8) and place them in their housing (4).

Release the three leg clamp knobs (6), lower the tripod pulling down the

at upper base (1), then lock in place the three extendable legs (8) with the

three leg clamp knobs (6).

Release the three mid-level spreader knobs (10), close the mid-level spread-

er to its folded posion and lock in place the mid-level spreader legs (5)

with the three mid-level spreader knobs (10).

Release the central brace knob (3) and completely fold the tripod; then lock

in place with the same central brace knob (3).

❼

6 servIce

The tripod has been designed and built in a way to reduce as much as pos-

sible any maintenance, and to ensure problem-free over me.

Aer any maintenance operaon, the tripod must be tested to ensure that

it is working properly.

6.1 routIne maIntenance

Sport 200 should be carefully periodically inspected and any damaged part

immediately replaced to prevent failures that might compromise the per-

sonnel’s safety and the tripod funconality.

Aer being exposed to rain, salted water, sand dust or mud the tripod

should be cleaned of all residues with clear water, compressed air and a

non abrasive cloth. Carefully dry before storing.

6.2 extra maIntenance and spare parts

Whatever extra maintenance requires to be carried out by CARTONI’s own

technical servicing sta or an authorized service staon appointed by CAR-

TONI.

Informaon on authorized service staon sta can be obtained by contact-

ing CARTONI or

www.cartoni.com

For fast, eecve problem solving CARTONI should be informed of the

tripod model and the nature of the defect or its visible symptoms when the

problem arises.

! All maintenance on the tripod must be carried out by

competent and instructed personnel on the operave

and safety methods of the tripod; all warranty condions

are invalidated should any repair operaon be aempted

by anyone not authorized by CARTONI

! Items whose center of gravity (CG) is too close to the

opened tripod base diameter (Jib arms, Teleprompters,

ecc.) could cause the tripod to p over; use addional

precauon to avoid accidents.

6.3 decommIsIonIng

In case the tripod becomes beyond repair it should be placed out of service

or at least clearly labeled as “out of order”.

Since the tripod is largely made of aluminum and steel

most of its materials can be recycled.

Once a Sport 200 is decommissioned, it is advisable to separate its various

materials for dierenated ulizaon or disposal, according the naonal

regulaons. Since none of the materials used on the tripod are toxic or may

cause a risk to the health of its operators, they can be handled without the

need for any special precauons.

! The dismantling of the tripod at the end of its life must

be carried out by competent and trained personnel.

CARTONI S.p.A

Via di Portonaccio, 33/B - 00159 Rome (Italy)

Phone +39 06 4382002

Fax +39 06 43588293

[email protected]

cartoni.com

PROFESSIONAL CAMERA SUPPORT

April 2023

Cartoni Sport 200 User manual

Brand: Cartoni

Model: Sport 200

Type: User manual

Download PDF

report

in other languages

italiano: Cartoni Sport 200 Manuale utente

Cartoni Sport 200 User manual

Cartoni Sport 200 User manual

in other languages

Related papers

Other documents