Eurolux F77DWB Owner's manual

Brand: Eurolux

Model: F77DWB

Type: Owner's manual

This manual is also suitable for

F77LWSC

3 Blade Fans

MODEL

F77LWSC / F77DWB

PRODUCT CODE

Cape Town - 9 Racecourse Road, Milnerton, 7441

Johannesburg - 10 Milkyway Avenue, Linbro Business Park, Sandton, 2065

www.eurolux.co.za

Please read instructions before commencing installation and retain for

future reference.

F77LWSC F77DWB

ILLUSTRATION

Waste electrical & Electronic equipment regulations requires that any of our products

showing this marking must not be disposed of with other household or commercial

waste. To prevent possible harm to the environment or human health from uncontrolled

waste disposal, please separate any such products from other waste types and

recycle it responsibly at your local facilities.

ENVIRONMENTAL PROTECTION

26. Male and female plug/quick connector

Twister 3 Blade Fan

22W 2700K-4000K LED

MODEL

F77DWB/F77LWSC

MODEL

TR52-MB-N3ABS1DFISC(LED-3K)/TR52-BC-N3ABS1DFISC(LED-3K)

PRODUCT CODE

MODEL

Cape Town - 9 Racecourse Road, Milnerton, 7441

Johannesburg - 10 Milkyway Avenue, Linbro Business Park, Sandton, 2065

www.eurolux.co.za

Please read instructions before commencing installation and retain for

future reference.

Description Of Parts:

1. Mounting bracket

2. Screw

3. Screw

4. Hanger ball

5. Upper Canopy

6. Downrod

7. Cross pin

8. Screw

9. Cotter pin

10. Downrod Yoke

11. Upper housing

12. Driver

13. Screw

14. Blade

15. Plate for x the blade

16. DC motor

17. Screw

18. Light plate

19. LED light

20. Glass

21. Remote control receiver

24. Male and female plug/quick connector

23. Male and female plug/quick connector

22. Remote control

25. Male and female plug/quick connector Includes Integrated 22W LED

CAUTION: Ensure power supply is turned off before attempting trouble shooting.

NOTE: This fan does not contain servicable parts. DO NOT OPEN or TAMPER WITH THE MOTOR.

Should your fan not start:

1) Check fuses are in place in the switchboard.

2) Recheck the terminal strip connections.

3) Ensure the wall & direction switches are not stuck in a “middle” position.

4) Ensure that the shipping tabs have been removed.

5) Ensure that the speed controller is not in the incorrect position.

Should your fan be noisy:

 1) Checkallscrewsaresufcientlytight:fanbladesandfanholders,(ifapplicable)glassofthe

lamp holder.

2) Allow at least 24 hours for the fan to settle.

Should your fan wobble:

In general, wobble is caused by the blades not cutting the air at the same point. Measure downwards

from the ceiling and make sure each blade is at the same height to the ceiling. See Figure 1. If they are

not, adjust by hand by slightly bending the blade and bracket. If a major adjustment is needed, insert a

washer as shown in Figure 2.

1) Check the blades are securely fastened to the holders.

2) Check the blade holders are tight on the motor.

3) Ensure the mounting bracket is properly screwed to the ceiling.

4) Interchange opposite blade sets if needed.

• Fitting material: Pressed steel & ABS

• Lens: Opal Glass

• Lamp: Integrated 22W LED

• Dimensions: (H)335mmx(Ø)1320mm

• Motor: DC 28W

• Voltage:220V-240V~50Hz

• Protection against electric shock: Class 1. Requires earth connection.

• IP:20.Protectedagainstsolidforeignobjectsof12.5mmØandgreater,notprotectedagainstwater.

• Not for outdoor use or in wet conditions and areas of high humidity.

• Features: 5 Speeds forward and reverse.

  Remotecompatible(Remoteincluded).

Warm and Cool White Switchable

Dimmable

• 2 year warranty

SPECIFICATIONS

TROUBLESHOOTING:

Touching

Ceiling

Figure 1

Fan Wobbles:

CLEANING

• Before cleaning always ensure the power supply is turned off and that the fan has been unplugged.

• Do not immerse the fan in water.

• No abrasive products, solvents, detergent may be used to clean this fan.

• Ensure that the fan does not come in contact with corrosive chemicals, etc.

• Remove the blades and wipe down parts with a damp cloth to remove any dust.

• Ensure all parts are dry before reassembling your fan.

• The motor bearings are permanently sealed and do not require additional lubrication.

F77LWSC / F77DWB-attachments:

Iftheexternalexiblecableorcordofthisfanisdamaged,itshouldbeexclusivelyreplacedbythe

manufacturerorhisserviceagentorasimilarqualiedpersoninordertoavoidahazard.Toensurethat

you get maximum longevity and maximum use out of your fan, please observe the following

safety instructions.

Electrical products can cause death, injury, or damage to property.

 Installationofthefanmustbecarriedoutbyaqualiedelectrician,inaccordancewithSANS10142.

 Oncompletionofinstallation,ensurethattheCerticateofComplianceisupdated.

• Before connecting this fan, ensure that voltage indicated on the rating label corresponds with the mains

voltage in your home.

• When cleaning, ensure that the power is turned off.

• This fan is checked in full for conformity to the quality standards and safety requirements.

• The manufacturer / supplier is not responsible for any damage of properties and persons, caused by

the incorrect use or installation of the fan.

• Should you be unsure of how to install this fan correctly, please consult a professional electrician or

your supplier for assistance.

• Ensure all items / components, threads and screws are tightly secured.

IMPORTANT:

• Tampering with this fan, i.e using silicon sealers or incorrect cabling, will invalidate your warranty.

• Please check whether the connection of the power cord is safe and reliable before installation.

• Always ensure that the mains supply voltage is correct.

• Do not use the fan outdoors, in wet conditions or areas of high humidity.

• Thisapplianceisnotintendedforusebyyoungchildrenorinrmpersonsunlesstheyhavebeen 

adequately supervised by a responsible person.

IMPORTANT SAFEGUARDS

OPERATION INSTALLATION

Secure the Mounting bracket to the ceiling

joist with the two long fixing screws provided

Loosing the cross pin and cotter pin from the

downrod. Loosing the screw from the hanger ball

Insert the upper canopy and lower canopy to

the downrod Insert the cross pin and lock the hanger ball and

downrod screw.

Insert the downrod to yoke and then insert the

cross pin and cotter pin to tight the yoke screw

Wire the incoming power cables to the terminal

block mounted on the Mounting bracket.

Wire Neutral, Earth, Active to the corresponding

N,L,terminals respectively.

Slide the remote control receiver unit inside the

Mounting bracket and carefully position all

excess cable inside upper canopy

7 8 9

4 5 6

1 2 3

to fix the downrod

Insert the hanger ball to downrod

INSTALLATION

The remote receiver has been pre-wired to the

Mounting bracket Do not remove. Connect the

quick-connectors between the remote

receiver and the motor (see above image)

Install the blade by the screw Connect the light plate with motor by the male

and female plug/quick connector. Tight up the light plate to motor

Fix the light plate by screw. put the glass, and turn clockwise direction to

lock it. Now the fan have complete

16 17 18

13 14 15

10 11 12 Loosing the screw from the motor

Slide the canopy up to cover the ball joint, wiring,

receiver and hanging bracket, then secure in place

Eurolux F77DWB Owner's manual

Brand: Eurolux

Model: F77DWB

Type: Owner's manual

This manual is also suitable for

F77LWSC

Download PDF

report

Eurolux F77DWB Owner's manual

This manual is also suitable for

Eurolux F77DWB Owner's manual

Related papers

Other documents