I N S T A L L A T I O N I N S T R U C T I O N S
Below Cart/Ceiling
Below Wall
(FCA830 shown)
Fusion™ Below Speaker Shelf
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
FCA830/840
FCA830/840 Installation Instructions
2
DISCLAIMER
Legrand | AV and its affiliated corporations and subsidiaries
(collectively “Legrand | AV”), intend to make this manual
accurate and complete. However, Legrand | AV makes no claim
that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Legrand | AV
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Legrand | AV
assumes no responsibility for accuracy, completeness or
sufficiency of the information contained in this document.
Chief® is a registered trademark of Legrand AV Inc.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the weight mounted to
the FCA830/840 bracket does not exceed 20 lbs (9 kg).
WARNING: Use of this accessory will decrease the weight
capacity of the mount to which it is attached by the combined
weight of the accessory and all components supported by
this accessory! See Figure below for reference.
WARNING: Use this accessory only for its intended use as
described in these instructions. Do not use attachments not
recommended by the manufacturer.
WARNING: Never operate this accessory if it is damaged.
Return the accessory to a service center for examination and
repair.
WARNING: Do not use this product outdoors.
WARNING: RISK OF INJURY TO PERSONS! Do not use
this accessory to support video equipment such as
televisions or computer monitors.
--SAVE THESE INSTRUCTIONS--
weight limit of mounting system minus
(*weight of FCA830/840 bracket + bracket components)
20 lbs (9 kg)
*FCA830 shelf weighs 7 lbs (3.18 kg)
*FCA840 shelf weighs 9 lbs (4.08 kg)
weight capacity of accessory
Installation Instructions FCA830/840
3
DIMENSIONS - FCA830
5.50 MIN
139.6 MIN
17.00 MAX
431.8 MAX
OVERALL
15.86 MAX
402.8 MAX
28.83 MAX
732.3 MAX
OVERALL
20.52 MIN
521.3 MIN
OVERALL
15.32 MIN
389.2 MIN
23.63 MAX
600.2 MAX
CENTER OF MOUNT
CENTER OF SPEAKER
MOUNT
1.55
39.4
(*)NOTES:
TYPICAL SINGLE DISPLAY MODELS HAVE INTERFACE DEPTHS .5" [12.7]
•
TYPICAL DUAL DISPLAY MODELS HAVE INTERFACE DEPTHS 1.9" [48.3]•
FCA623 DUAL MONITOR INTERFACES ARE 1.4" DEEP [35.6]•
FUSION CEILING/CART MOUNT SETUP
FCA830/840 Installation Instructions
4
DIMENSIONS - FCA840
Installation Instructions FCA830/840
5
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
FCA830/840 Installation Instructions
6
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
3/8”
5/32” (included)
1/8” (included)
A (1)
[Upright bracket]
D (1)
[Wall speaker
B (1)
[Main bracket] E (1)
[Speaker interface - left]
L (2)
1/4-20 x 1/2”
K (8)
C (1)
[Wall speaker
G (2)
#10-24 H (8)
F (1)
[Speaker interface - right]
[Large washer]
J (1)
#10-24 x 1/4”
M (5)
N (1)
1/4-20 X 5/8”
P (1)
#10-32 x 3/8”
5/32”
Z (1)
1/4-20 x 1/4”
[Small washer]
Q (4)
1/4-20 x 1/2”
T (2)
#10-24 x 1/2”
V (1)
[Adapter plate]
AA (1)
1/8”
R (4)
1/4-20 x 7/16”
U (4)
1/2”
W (2)
BB (1)
[Speaker bracket]
#10-24 x 1 1/8”
interface - right]
interface - left]
X (2)
[Shelf bracket]
Y (1)
[Center washer]
(FCA840 shown)
Installation Instructions FCA830/840
7
ASSEMBLY AND INSTALLATION
Attaching Speaker Bracket to Upright Bracket
1. Install two 1/4-20 x 1/2” button head cap screws (L) into
lowest holes on upright bracket (A). (See Figure 1) or (See
Figure 2)
IMPORTANT ! : Refer to Figure 3 if installing to a wall
mount or Figure 4 if installing to a cart/ceiling mount.
2. Hang speaker bracket (BB) onto two screws installed in
Step 1. (See Figure 1) or (See Figure 2)
3. Use one 1/4-20 x 1/4” button head cap screw (M) to secure
upright bracket (A) to speaker bracket (BB). (See Figure 1)
or (See Figure 2)
4. Tighten all three screws to ensure upright bracket (A) is
securely attached to speaker bracket (BB).
Figure 1
Figure 2
Attaching Speaker Bracket to Wall Mount
NOTE: If attaching to cart or ceiling mount, proceed to Attach
Speaker Bracket to Cart/Ceiling Section.
1. Use two 1/4-20 x 1/4” button head cap screws (M) and two
large washers (H) to secure shelf bracket (X) to main
bracket (B). (See Figure 3)
CAUTION: Slide bracket with caution so that the bracket
does not scratch or damage the wall!
2. Slide main bracket (B) behind wall mount rails until shelf
bracket (X) rests on top of wall mount rail. (See Figure 3)
Figure 3
3. Slide second shelf bracket (X) underneath lower rail on wall
mount, lining up holes on shelf bracket (X) to main bracket
(B). (See Figure 4)
4. Use two 1/4-20 x 1/4” button head cap screws (M) and two
large washers (H) to secure shelf bracket (X) to main
bracket (B). (See Figure 4)
Figure 4
(L) x 2
1
3
(M)
2
2
(Wall Mounting)
(BB)
(A)
(L) x 2
1
3
(M)
2
2
(Cart/Ceiling Mounting)
(A)
(BB)
2
(M) x 2
1
(H) x 2
(B)
(X)
(Wall Mounting)
3
wall mount rails
4
(M) x 2
(X)
(H) x 2
(B)
(Wall mounting)
FCA830/840 Installation Instructions
8
NOTE: Refer to Table 1 and dimension drawings on pages 3-
4 to determine the extension level based on extension
distance from mount center.
Table 1: Wall Mounting
5. (For maximum extension) Use #10-32 x 3/8” button head
cap screw (P) and small washer (J) to secure adapter plate
(V) to main bracket (B). (See Figure 5)
6. (For maximum extension) Use two #10-24 lock nuts (G) to
secure upright bracket (A) to main bracket (B) and adapter
plate (V). (See Figure 5)
Figure 5
7. (For minimum/intermediate extension) Use two #10-24
lock nuts (G) to secure upright bracket (A) to main bracket
(B) and adapter plate (V). (See Figure 6)
NOTE: Minimum configuration is shown below. Several
intermediate configurations are possible depending on
which holes are used.
8. (For minimum/intermediate extension) Use 1/4-20 x 5/8”
hex head flange bolt (N) and center washer (Y) to secure
upright bracket (A) to main bracket (B). (See Figure 6)
Figure 6
Attaching Speaker Bracket to Cart/Ceiling Mount
IMPORTANT ! : If installing to a 2x1 display cart using
the FCA623 accessory, proceed to “Installing to FCA623
Accessory” Section (Step 6).
1. Use two 1/4-20 x 1/4” button head cap screws (M) and two
large washers (H) to secure shelf bracket (X) to main
bracket (B). (See Figure 7)
2. Slide main bracket (B) onto front of cart/ceiling mount head
assembly until shelf bracket (X) rests on top of head
assembly. (See Figure 7)
Figure 7
Extension distance from
center of mount (in.)
FCA830
Extension distance from
center of mount (in.)
FCA840
15.7-17.9 20.7-23.8 Minimum
17.9-20.4 23.8-32.2 Intermediate
20.4-22.0 32.2-33.7 Maximum
(V)
(B)
(A)
(J)
(P)
5
(G) x 2
6
(Wall - maximum)
(FCA840 shown)
(G) x 2
7
(B)
(A)
(N)
8
(Wall - minimum)
(V)
(Y)
holes to
use for intermediate
configurations
(FCA840 shown)
(rear view)
(X)
2
(M) x 2
1
(H) x 2
(B)
(Cart/ceiling - Standard)
Installation Instructions FCA830/840
9
3. Slide second shelf bracket (X) underneath head assembly,
lining up holes on shelf bracket (X) to holes on main bracket
(B). (See Figure 8)
4. Use two 1/4-20 x 1/4” button head cap screws (M) and two
large washers (H) to secure shelf bracket (X) to main
bracket (B). (See Figure 8)
Figure 8
5. Proceed to Step 11 unless installing to FCA623 accessory.
Installing to FCA623 Accessory
IMPORTANT ! : Steps 6-10 only apply if installing to
FCA623 accessory.
6. Use two 1/4-20 x 7/16” button head cap screws (R), two
large washers (H) and two 1/2” spacers (U) to secure shelf
bracket (X) to main bracket (B). (See Figure 9)
7. Slide main bracket (B) onto front of cart/ceiling mount head
assembly until shelf bracket (X) rests on top of head
assembly. (See Figure 9)
Figure 9
8. Slide second shelf bracket (X) underneath head assembly,
lining up holes on shelf bracket (X) to holes on main bracket
(B). (See Figure 10)
9. Slide two 1/2” spacers (U) in between shelf bracket (X) and
main bracket (B). (See Figure 10)
10. Use two 1/4-20 x 7/16” button head cap screws (R) and two
large washers (H) to secure shelf bracket (X) to main
bracket (B). (See Figure 10)
Figure 10
NOTE: Refer to Table 2 and dimension drawings on pages 3-
4 to determine the extension level based on extension
distance from mount center.
Table 2: Cart/Ceiling Mount
11. (For maximum extension) Use #10-32 x 3/8” button head
cap screw (P) and small washer (J) to secure adapter plate
(V) to main bracket (B). (See Figure 11)
12. (For maximum extension) Use two #10-24 lock nuts (G) to
secure upright bracket (A) to main bracket (B) and adapter
plate (V). (See Figure 11)
Figure 11
(rear view)
(X)
(M) x 2
4
(H) x 2
3
(B)
(Cart/ceiling - Standard)
(rear view)
(X)
7
(R) x 2
6
(H) x 2
(B)
(Cart with FCA623 accessory)
(U) x 2
Extension distance from
center of mount (in.)
FCA830
Extension distance from
center of mount (in.)
FCA840
15.3-17.2 20.9-22.2 Minimum
17.2-22.1 22.2-33.8 Intermediate
22.1-23.6 33.8-35.3 Maximum
(rear view)
(X)
(R) x 2
10
(U) x 2
8
(B)
(Cart with FCA accessory)
(H) x 2
9
(G) x 2
12
(B)
(A)
(P)
11
(Cart/ceiling - maximum)
(V)
(J)
holes to
use for intermediate
configurations
(FCA840 shown)
(rear view)
FCA830/840 Installation Instructions
10
13. (For intermediate extension) Use #10-32 x 3/8” button
head cap screw (P) and small washer (J) to secure adapter
plate (V) to main bracket (B). (See Figure 11)
14. (For intermediate extension) Use two #10-24 lock nuts (G)
to secure upright bracket (A) to main bracket (B) and
adapter plate (V). (See Figure 11)
15. (For minimum extension) Use 1/4-20 x 5/8” hex head
flange bolt (N) and center washer (Y) to secure upright
bracket (A) to main bracket (B). (See Figure 12)
Figure 12
Installing Speaker (not included)
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the weight mounted on
the
FCA830/840 bracket does not exceed 20 lbs (9 kg)
.
WARNING: USING SCREWS OF IMPROPER SIZE MAY
DAMAGE THE SPEAKER. Properly sized screws will easily
and completely thread into speaker mounting holes.
NOTE: If the screws provided with this accessory do not fit the
specific speaker being installed, be sure to use
correctly sized screws (not included).
NOTE: If installing to speaker with teardrop openings at
attachment points, proceed to “Optional Speaker
Installation” Section.
Installing to Cart/Ceiling Mounts
1. Attach left speaker interface (E) to back of speaker (left
side) using two 1/4-20 x 1/2” Phillips pan head screws (Q)
with two large washers (H). (See Figure 13)
NOTE: Ensure that upper flange of interface brackets are at top
of speaker. (See Figure 13)
2. Repeat Steps 1 with right speaker interface (F). (See Figure
13)
Figure 13
3. Install two speaker interfaces (E and F) to speaker bracket
(BB) by sliding upper flanges of interfaces into long slots on
speaker bracket and then pushing interfaces into position.
(See Figure 14)
4. Use two #10-24 x 1 1/8” button head cap screws (W) to
secure interfaces to speaker bracket at desired speaker
position. (See Figure 14)
Figure 14
(G) x 2
14
(B)
(A)
(P)
13
(Cart/ceiling - intermediate)
(V)
(J)
(FCA840 shown)
(rear view)
(N)
15
(FCA840 shown)
(rear view)
(Cart/Ceiling Minimum)
(B)
(A)
(Y)
(E)
(F)
upper flanges
2
(Q) x 2
1
(Q) x 2
(H) x 2
(H) x 2
speaker
(not included)
(W) x 2
(BB)
(E)
4
3
3
3
3
(F)
(speaker not shown for clarity)
Installation Instructions FCA830/840
11
Installation to Wall Mount
1. Attach left wall speaker interface (C) to back of speaker (left
side) using two 1/4-20 x 1/2” Phillips pan head screws (Q)
with two large washers (H). (See Figure 15)
2. Repeat Steps 1 with right wall speaker interface (D). (See
Figure 15)
Figure 15
3. Use eight #10-24 x 1/4” button head cap screws (K) to
secure two wall speaker interfaces (C and D) to two speaker
interfaces (E and F). (See Figure 16)
Figure 16
4. Install two speaker interfaces (E and F) to speaker bracket
(BB) by sliding upper flanges of interfaces into long slots on
speaker bracket and then pushing interfaces into position.
(See Figure 17)
5. Use two #10-24 x 1 1/8” button head cap screws (W) to
secure interfaces to speaker bracket at desired speaker
position. (See Figure 17)
Figure 17
OPTIONAL SPEAKER INSTALLATION
Speaker With Teardrop Opening At Attachment
Points
1. Insert two 10-24 x 1/2” Phillips pan head screws (T) into
speaker interfaces (E and F) [Cart/Ceiling Mounting] or
wall speaker interfaces (C and D) [Wall Mounting] and
hang speaker on screws. (See Figure 18)
Figure 18
2. Proceed to Step 3 of corresponding speaker installation
section to complete installation.
Height Adjustment
1. Loosen hardware used to attach main bracket (B) to upright
bracket (A). (See Figure 19)
2. Adjust shelf height as desired using intermediate holes as
needed. (See Figure 19)
3. Tighten hardware used to attached main bracket (B) to
upright bracket (A). (See Figure 19)
Figure 19
(C)
(D)
2
(Q) x 2
1
(Q) x 2
(H) x 2
speaker
(not included)
(C)
(K) x 8
3
(D)
(E)
(F)
(W) x 2
5
4
4
4
4
(BB)
(E)
(F)
1
(T) x 2
Cart/Ceiling Mounting
Wall Mounting
(E) (F)
(C) (D)
2
13(Cart/Ceiling shown
as example)
(FCA840 shown)
FCA830/840 Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
8800-002653 Rev04
2019 Legrand | AV
www.legrandav.com
07/19
/
