revolt GC88710-23 User manual

Type
User manual
TG1023
5+
Light up
wheels
321.8g
16.5 x 16 x 7cm / 6.5’ x 6.3’ x 2.75’
appr. 30 meters / 100 Feet
appr. 90 min
appr. 15 min
3.7V500mAh rechargeble battery (included)
Remote Control Vehicle
IMPORTANT SAFETY INFORMATION
PRODUCT SPECIFICATIONS
Thank you for buying this REVOLT item.To ensure that you operate the vehicle correctly. Please
read these instructions carefully before first use and store them in a safe place for future reference.
Remote Control
1x Light stunt car
1x USB Charging Cable
1x Remote Control
BASIC OPERATING INSTRUCTIONS:
OFF/ON
OFF/ON
Left Joystick Right Joystick
PAIRING:
1.Switch the vehicle power to ‘’ON’’.
2. Switch the remote Control to ‘’ON’’.
3. The vehicle and remote Control will pair
automatically when both are ‘’ON’’.
Forward
Push both joysticks upward
to make the vehicle
move forwards
Backward
Push the left joystick
upward to make the
vehicle turn right
Left steering
Push the right joystick
upwards to make the
vehicle turn left
Right steering
Push both joystick downward
to make the vehicle
move backwards
360° left rotation
Push the left joystick down and
the right joystick up and the vehicle
will make a 360°rotation spinning left.
360° right rotation
Push the left joystick up and
the right joystick down and the vehicle
will make a 360°rotation spinning right.
MOVING THE VEHICLE:
2x1.5V“AA”
Remote control car
Remote control
1.Check the ON/OFF switch is in the ‘’OFF’’ position.
2.Use a screwdriver to loosen the screw.
3.Remove the battery cover.
4.Install the battery as indicated in the picture
on the right:
Connect the rechargeable battery in the
battery pack as indicated in the picture.
5.Put the battery cover back and tighten the screw.
1.Check the ON/OFF switch is in the “OFF” position.
2.Use a screwdriver to loosen the screw.
3.Remove the battery cover.
4.According the polarity indicated inside in the
remote control. Put the 2*AA battery into the
battery compartment.
5.Put the battery cover back and tighten
the screw.
Note: If breakdown occurs in the product, please take out the
battery for one minute, and then reinstall it. If the breakdown
still exists, please replace the battery. The battery can only
be installed by the adults.
3.7V
INSERTING THE BATTERIES
CHARGING THE BATTERIES
Vehicle
Battery charging
·Connect the USB charger to USB output on computer or AC/DC adaptor,then insert the car
charger plug to the vehicle charging port (see diagram)
·A full charge takes 90 minutes. When charging the LED indicator turns red,when charging
is complete,the LED indicator stays off.
·Regularly inspect the toy, battery charger, charging cable, connectors and other components
for signs of damage. In the event of any damage, discontinue use and send the parts
for repair.
Charge plug
·In case of abnormal responses such as suspicious smell, noise or smoke in the charger,
please remove the power supply at once.
·Please recharge with the dedicated USB charging cable delivered with the product.
Never use broken charging cables or charging cables from other products.
·Please do not recharge the swelling, leaking or broken battery.
·Please do not overcharge the battery. When the battery is fully recharged, please stop charging!
·Please do not recharge the battery near flammable things(carpet, wood floor,furniture, etc.)
or of conductive objects. While recharging, please keep the battery within line of sight.
·Do not touch moving Wheels' to avoid entanglment and injury to yourself or damage to the car.
·Please do not play by the road or in dangerous places that could accidents.
·Do not use this vehicle near water.
·Before using the car, make sure the car battery cover screws are tightened. Failure to tighten
may cause water damage to the vehicle.
·If recharging is necessary, please take the battery out of the remote control vehicle
(if applicable).
Caution
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

revolt GC88710-23 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI