Hunter Fan Company 59244 User manual

Brand: Hunter Fan Company

Model: 59244

Category: Household fans

Type: User manual

Installation Manual

Model: 50282 Brushed Nickel

59243 Brushed Nickel

59244 Fresh White

59445 Noble Bronze

Fan weight ±2 lbs: 18.3 lbs (8.3 kg)

Dempsey

PG3773 r042519

1886

Ladder

9/64” Drill BitDrill

Screwdriver

Pliers

Wire Strippers

OPTIONAL

If mounting to a support structure, you will also need these tools.

Congratulations on purchasing your new Hunter

ceiling fan!

Here are the tools you’ll need to complete your installation:

The ceiling fan you purchased will provide comfort and performance in your home or ofce for many years. This instruction manual contains

complete instructions for installing and operating your fan. We are proud of our work and appreciate the opportunity to supply you with the

best ceiling fan available anywhere in the world.

We are here to help!

This Instruction Manual is designed to make installation as simple as possible. While working through this Instruction Manual, keep

your smartphone or tablet nearby. We have added video links to help you through the more technical sections. If you are unfamiliar or

uncomfortable with wiring, contact a qualied electrician. We also provide telephone support at 1.888.830.1326 or visit us

at HunterFan.com.

WARNING

READ and SAVE These Instructions

Warning

w.1 - To reduce the risk of re, electrical shock, or personal injury, mount fan directly from building structure and/or an outlet box marked acceptable for fan support of 70 lbs (31.8 kg) and use the

mounting screws provided with the outlet box.

w.2 - To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location. If you

cannot lock the circuit breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service panel.

w.3 – To reduce the risk of electric shock, this fan must be installed with an isolating wall control/switch.

w.4 - To reduce the risk of personal injury, do not bend the blade brackets when installing the blade brackets, balancing the blades, or cleaning the fan. Do not insert foreign objects in between

rotating fan blades.

w.5 - Chemical burn hazard. Keep batteries away from children. This remote contains a lithium button cell battery. If a new or used lithium button/coin cell battery is swallowed or enters the body,

it can cause severe internal burns and can lead to death in as little as 2 hours. Always completely secure the battery compartment. If the battery compartment does not close securely, stop using

the product, remove the batteries, and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

Dispose of cells properly and keep away from children. Even used cells may cause injury.

Caution

c.1 - All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualied electrician.

c.2 - Use only Hunter replacement parts.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions

may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Caution: modications not approved by the party responsible for compliance could void user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

This product conforms to UL Standard 507.

1886

Do not discard the hardware bags or mix parts from

different bags. Make note of the symbol printed on

each hardware bag. The symbols can be used to

identify the appropriate hardware for each step.

We recommend that you pull everything out of the box and lay it out. We have

grouped the drawn components below with the hardware you’ll need for those

parts. The screws below are drawn to scale to make it easier to identify what

piece of hardware is needed to install each component.

For installing the hanger bracket and wiring the fan

For installing the blades

For installing the canopy

For installing the light kit

Motor

Canopy

Screw

Top Housing

Screw

Grounding

Screw

Ceiling Bracket

Canopy Trim Ring

Wood Screw

Wire Nut

Washer

bag

Hunter Pro Tip:

Find a part that is missing or damaged?

Don’t take it back to the store. Let us make it right. Visit us at HunterFan.com or call us at 1.888.830.1326.

Here is what comes in your box:

bag

M0230-01 r042519

Spare Parts

For your convenience,

you may receive extra fasteners.

bag

Remote Components

Remote Control

Remote Receiver

Remote Cradle

Upper Motor Housing

x12 x12

Blade ScrewBlade Washer

bag bag

Blade

Glass

Upper Switch Housing

Light Kit Assembly

x6Light Kit Screw

bagx2

1886

Trim Ring

Top Housing

Adapter

Choosing the Right Installation Location

You probably bought this fan with a location in mind. Let’s check below to make sure it is a good t.

Check the room dimensions: Check the outlet box:

You must be able to

secure the fan to building

structure or fan-rated

outlet box.

30 inches

from blade tip to

nearest wall or

obstruction

7 feet

from bottom edge

of blade to the

oor

Installing the Ceiling Bracket

Use wood screws and

washers (included) when

securing to support structure

with approved electrical

outlet box. Drill 9/64” pilot

holes in support structure

to aid in securing ceiling

bracket with hardware found

in the hardware bag.

Use machine screws

(provided with outlet box)

and washers when securing

to existing ceiling fan-rated

outlet box. Make sure it is

securely installed and is

acceptable for fan support of

31.8 kg (70 lbs) or less.

Option 2:

Wood Screws

Option 1:

Machine Screws

OFF

Turn Power

Do this rst!

bag

Wood Screw

Washer

You have two options for installation. Pick which one works best for your location. Remove any existing

bracket prior to installation. Only use the provided Hunter ceiling bracket that came in your fan’s box.

Installing the Top Housing

Thread the wires through the top housing.

Place the top housing onto the motor housing

so that the holes in the top housing lineup with

the holes in the motor housing and the adapter.

Rest the trim ring on the top housing.

Canopy

Adapter

Place the canopy on the top housing. Ensure

all four screw holes line up with the screw

holes in both the top housing and the adapter.

Ceiling Bracket Hanging Fan Wiring Canopy Blades Light Bulbs Remote

The machine screws are the ones that

came with your outlet box.

Hunter Pro Tip:

1886

Check the outlet box:

Wood Screw

Installing the Top Housing

8”

3/8”

(not to scale)

Top Housing

Screw

Grounding

Screw

bag

The wires can be cut, but

leave at least 8” extending

from the top of the canopy.

Install the top housing screws. Install

the grounding screw in the smaller

screw hole. These screws can be

found in the hardware bag.

Grounding

Screw

Hanging the Fan

NOTICE

To prevent damage to fan,

ALWAYS lift holding the fan

housing.

Note: To hang the fan, you must tilt the canopy to

an almost vertical position so that the canopy slots

sit on the ceiling plate hooks.

Raise the fan and align the slots in the

canopy with the hooks on the ceiling plate.

Place the slots over the ceiling

plate hooks to hang the fan.

8” 3/8”

Ceiling Bracket Hanging Fan Wiring Canopy Blades Light Bulbs Remote

1886

We know wiring is hard. Let’s make it easier.

You are going to need these:

4 Wire Nuts (these are in the bag)

Follow these steps to get your fan wired quickly and safely. Follow the route below that best matches your wall switch

setup. If you are unfamiliar with wiring or uncomfortable doing it yourself, please contact a qualied electrician.

Wiring the Fan

Hunter Pro Tip:

Here is how to connect the wires:

Push the bare metal ends of the wires together and slide a wire

nut over them. Then, twist the wire nut clockwise until tight.

Give it a gentle pull to make sure none of the wires are loose.

Connect the 2 grounding

wires (green, green/

yellow stripe, or bare

copper) coming from the

ceiling and ceiling plate.

Connect the black wire

(ungrounded) from the

ceiling to the black

wire from the receiver.

Connect the white wire

(grounded) from the ceiling

to both the white wire from

the receiver and the white

wire from the fan.

White

Black

Ungrounded

Grounded

Connect the blue wire

from the receiver to the

blue wire (or possibly

black with white stripe

wire) from the fan.

Connect the yellow wire

from the receiver to the

black wire from the fan.

Black

Yellow

Blue

WARNING

All wiring must be in accordance with

national and local electrical codes ANSI/NFPA

70. If you are unfamiliar with wiring or in

doubt, consult a qualied electrician.

STEP

Ceiling Bracket Hanging Fan Wiring Canopy Blades Light Bulbs Remote

1886

Installing the Canopy

2 of 3

Canopy

Screws

bag

1 of 3

Canopy

Screws

bag

Swing the fan up to align the

canopy screw holes with the

mounting holes on the ceiling plate.

Using both hands, push the canopy trim

ring up to the top of the canopy. The canopy

trim ring will snap and lock into place.

Hold the canopy up with the screw holes

aligned. Partially install two canopy screws,

found in the hardware bag, into the

holes opposite the ceiling plate hooks.

Partially install a canopy screw, found

in the hardware bag, between

the ceiling plate hooks. When all the

holes are properly aligned, securely

tighten all three canopy screws.

Note: The slots in the canopy

must remain engaged while

swinging the canopy for

alignment.

Note: Should you need to remove the trim ring,

press rmly on opposite sides of the trim ring. The

tabs will ex out releasing the canopy trim ring.

Place the receiver inside the

canopy. Ensure the wires

remain connected.

WARNING

FAN FALL HAZARD

Make sure screws are tight.

Installing the Blades:

Attach each blade to a blade iron using the blade washers, found in

the hardware bag, and the blade assembly screws, found in the

hardware bag.

Repeat x4

x12

bag

Blade Screw

x12

bag

Blade Washer

Ceiling Plate Hooks

Ceiling Bracket Hanging Fan Wiring Canopy Blades Light Bulbs Remote

1886

Ceiling Bracket Hanging Fan Wiring Canopy Blades Light Bulbs Remote

Assembling the Switch Housing

WARNING

FAN FALL HAZARD

Make sure the hood is securely attached to the mounting

plate. Failure to properly secure all 3 assembly screws could

result in the switch housing xture falling.

Screw two housing assembly screws from the

hardware bag halfway into the motor housing. It

does not matter which two screw holes you choose.

Feed the wire plug through the center hole of the

hood, then wrap keyhole slots around the screws

and twist counterclockwise.

Insert the third screw, found in the hardware

bag, into place and then tighten all three screws.

2 of 6

Light Kit Screw

bag

1 of 6

Light Kit Screw

bag

Assembling the Light Kit

Install the third switch housing screw. Tighten all

three screws securely.

Connect the plugs from the upper and lower

switch housings. Make sure to line up the

colored markings on the connectors.Wrap light

kit keyhole slots around the screws and twist

counterclockwise.

Screw two housing assembly screws from the

hardware bag halfway into the upper switch

housing. It does not matter which two screw holes

you choose.

2 of 6

Light Kit Screw

bag

1 of 6

Light Kit Screw

bag

WARNING

FAN FALL HAZARD

Make sure screws are tight to secure the

light xture.

Tab

Notch

Install a bulb into each of the sockets. When

necessary, replace with bulbs of the same

type and wattage.

WARNING

GLASS FALL HAZARD

To prevent SERIOUS INJURY or DEATH, make

sure that glass is properly secured.

Lift the globe and align the notches in the

globe with the tabs in the light kit. Attach

the glass bowl to the light kit by twisting it

clockwise until it snaps into place.

1886

Ceiling Bracket Hanging Fan Wiring Canopy Blades Light Bulbs Remote

Preparing the Remote Control

The remote control is already

paired for use.

For your convenience, a

remote function card is

packed in with your remote.

Using the Remote Control Cradle

To access the battery compartment, remove the

small Phillips head screw that secures the battery

door to the transmitter assembly. The battery

should be installed with the positive (+) side up.

Replace with a CR2032 battery when necessary.

The remote transmitter should already be paired

to the receiver and ready to use.

Note: If your need to pair your remote, turn fan

power off and back on at the wall switch. Within

3 minutes, press and hold both the Fan Off button

and the High button for 4 seconds to pair the

remote. To prevent faulty operation, please

ensure all other ceiling fans within range are

turned off at the wall switch while pairing.

To install the transmitter cradle, remove the two

screws holding the switch cover plate. Do not remove

the cover plate. Orient the cradle by lining up the two

mounting holes with those on the cover plate. Insert

and tighten the screws. Do not over tighten.

Note: For rocker-style cover plates, break off the

tabs by pushing outward.

To turn on fan, press a fan speed

button. Speeds range from off (0)

to high (3). Quickly press the Light

button to turn the lights off and on.

Fan Off

Light On/Off

Fan Medium

Fan High

Fan Low

Battery Door

Phillips Head

Screw

Switch Cover

Plate

Rocker Style

Plate

Removed Tabs

Turn Power

Assembling the Light Kit

1886

Hunter Fan Company grants this limited warranty to the original purchaser of this Hunter

ceiling fan. This document can be found at www.HunterFan.com.

Thank you for choosing Hunter!

How Can Warranty Service Be Obtained?

Proof of purchase is required when requesting warranty service. The original

purchaser must present a sales receipt or other document that establishes proof of

purchase. Hunter, at its sole discretion, may accept a gift receipt. To obtain service,

contact Hunter Fan Company online or by phone.

www.HunterFan.com/Support/Contact-Us/

1-888-830-1326

Please do not ship your fan or any fan parts to Hunter. Delivery will be refused.

What Does This Warranty Cover?

Motor — Limited Lifetime Warranty

If any part of your ceiling fan motor fails during your ownership of the fan due to a

defect in material or workmanship, as determined solely by Hunter, Hunter will provide

you with a replacement fan free of charge.* The foregoing limited warranty applies only

to the motor itself and does not apply to electronic controls – such as remote control

transmitters, remote control receivers, or capacitors – used in conjunction with the

motor. Such electronic control items are included in the one-year limited warranty below.

Other — One-Year Limited Warranty

Except as otherwise indicated throughout this warranty, if any part of your Hunter ceiling

fan fails at any time within one year of the date of purchase due to a defect in material

or workmanship, as determined solely by Hunter, Hunter will provide a replacement part

free of charge.*

Light Kits — Warranty May Vary

Light kits are included in the one-year limited warranty. However, you may qualify for

additional warranty coverage if your fan includes one of the following:

• LED Light Kits — Three-Year Limited Warranty

If your LED light kit module (not including glass components) or LED bulb

fails at any time within three years of the date of purchase due to a defect

in material or workmanship, as determined solely by Hunter, Hunter will

provide a replacement part free of charge.*

* If no replacement product/part can be provided for your fan, we will provide a comparable or

superior replacement product/part at the sole discretion of Hunter.

What Does This Warranty NOT Cover?

Labor Excluded. This warranty does not cover any costs or fees associated with the labor

(including electrician’s fees) required to install, remove, or replace a fan or any fan parts.

There is no warranty for light bulbs (except where otherwise noted); remote control

batteries; fans purchased or installed outside the United States; fans owned by

someone other than the original purchaser; fans for which proof of purchase has not

been established; fans purchased from an unauthorized dealer; ordinary wear and tear;

minor cosmetic blemishes; refurbished fans; and fans that are damaged due to any

of the following: improper installation, misuse, abuse, improper care, failure to follow

Hunter instructions, accidental damage caused by the fan owner or related parties,

modications to the fan, improper or incorrectly performed maintenance or repair,

improper voltage supply or power surge, use of improper parts or accessories, failure to

provide maintenance to the fan, or acts of God (e.g. ood).

ORIGINAL PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR A CLAIM OF ANY KIND

WITH RESPECT TO THIS PRODUCT SHALL BE THE REMEDIES SET FORTH HEREIN.

HUNTER FAN COMPANY IS NOT RESPONSIBLE FOR CONSEQUENTIAL OR INCIDENTAL

DAMAGES, DUE TO PRODUCT FAILURE, WHETHER ARISING OUT OF BREACH OF

WARRANTY, BREACH OF CONTRACT, OR OTHERWISE. Some States do not allow the

exclusion or limitation of incidental or consequential damages, so the above limitation or

exclusion may not apply to you.

ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE APPLICABLE TO THIS PRODUCT ARE LIMITED IN DURATION TO THE PERIOD OF

COVERAGE OF THE APPLICABLE LIMITED WARRANTIES SET FORTH ABOVE. Some States

do not allow limitations on how long an implied warranty lasts, so the above limitation

may not apply to you.

How Does State Law Affect Warranty Coverage?

This warranty gives you specic legal rights. You may also have other rights which vary

from state to state.

Limited Lifetime Warranty

Reversing the Fan

Reverse

Switch

Ceiling fans work in two directions: downdraft

(counterclockwise rotation) and updraft

(clockwise rotation). To change the direction

of air ow, turn the fan off and let it come to a

complete stop. Slide the reversing switch to the

opposite position. Restart the fan.

Updraft (clockwise rotation)

creates a more indirect airow.

Updraft airow is great for

moving warm air downward.

Downdraft (counterclockwise

rotation) creates a direct breeze

and maximum cooling effect.

Troubleshooting

1886

Troubleshooting

Cleaning the Fan

Use soft brushes or cloths to prevent scratching.

Cleaning products may damage the nishes.

Hunter Pro Tip:

Fan Doesn’t Work

• Make sure power switch is on.

• Check the circuit breaker to ensure the power is turned on.

• Make sure the blades spin freely.

• Turn off power from the circuit breaker, then loosen the canopy

and check all the connections according to the wiring diagram.

Excessive Wobbling

• Make sure the blades are properly installed on the blade iron

posts.

• Turn the power off, support the fan carefully, and check that the

hanger ball is properly seated.

• Use the provided balancing kit and instructions to balance the fan.

Noisy Operation

• Make sure the blades are properly installed.

• Check to see if any of the blades are cracked. If so, replace all of

the blades.

Remote Control of Fan is Erratic

• Make sure the battery is installed correctly.

• Install a fresh battery.

Multiple Remote Issues

• If you have multiple remotes or multiple remote-controlled fans

installed on the same circuit breaker and you are experiencing

interference or faulty operation of your remote controls, please

go to

www.HunterFan.com/FAQs and click “How do I properly install

multiple remote-controlled fans?” for information on how to

correct this issue.

Hunter Fan Company 59244 User manual

Brand: Hunter Fan Company

Model: 59244

Category: Household fans

Type: User manual

Download PDF

report

Hunter Fan Company 59244 User manual

Hunter Fan Company 59244 User manual

Other documents