System Build 7467056COM User manual

7467056COM

STORAGE CABINET

- Unit can tip over causing severe injury or death.

- Anchor unit to stud in wall (if instructed to).

- Do Not allow children to climb on unit.

- Put heavy items on lower shelves or drawers.

B347467056COMT0

THIS INSTRUCTION BOOKLET CONTAINS

IMPORTANT

SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.

WARNING

For the latest information on SystemBuild products

follow us at Ameriwood Home

Tube

You

Date of Purchase ___ / ___ / ___

Lot Number:

Do Not Return This Product!

Contact our customer service team for help first.

Call: 1-866-452-4081 (toll free)

Monday-Friday 9am - 5pm CST

Visit: www.systembuild.com

Assembly Difficulty Meter

Easy

Tough

Contact Us!

Helpful Hints

2

systembuild.com

Do NOT return this product!

Contact our friendly customer service team first for help.

Call us!

1-866-452-4081

Monday-Friday

9am - 5pm CST

Visit systembuild.com to view the

limited warranty valid in the U.S. and Canada.

Assembly Tips

- Open your item in the area you plan to keep it to avoid excessive heavy lifting.

- Identify, sort and count the parts before attempting assembly.

- Compression dowels are lightly tapped in with a hammer.

- Slides are labeled with a

R

(right) and

L

(left) for proper placement.

- Make sure to always face the point on the top of the Cam Lock towards the

outer edge.

- Use all the nails provided for the back panel and spread them out equally.

- Back panel must be used to make sure your unit is sturdy.

- Do NOT use harsh chemicals or abrasive cleaners on this item.

- Never push, pull, or drag your furniture.

Tube

You

Tube

You

PEOPLE NEEDED FOR ASSEMBLY: 1-2

ESTIMATED ASSEMBLY TIME: 1 HOUR

3

systembuild.com

Before You Start

P

Q

u

i

c

k

T

i

p

A

s

e

m

bl

y

P

Tube

You

Read through each step carefully and follow the proper order

Separate and count all your parts and hardware

Give yourself enough room for the assembly process

Have the following tools: Flat Head Screwdriver, #2 Phillips Head

Screwdriver and Hammer

Caution: If using a power drill or power screwdriver for screwing,

please be aware to slow down and stop when screw is tight.

Failure to do so may result in stripping the screw.

P

4

systembuild.com

Board Identification

Not actual size

Tube

You

This piece is

paperboard

construction.

It is not made from

wood, but is required

for the assembly of

your unit.

2 End Panels

37467056010

top

37467056030

bottom

37467056040

fixed shelf

37467056050

2 Adjustable Shelves

37467056060

left door

37467056070

right door

37467056080

back panel

K74675600

H

G

F

E

D

C

A

I

5

systembuild.com

Board Identification

Not actual size

A

C

D

E

F

G

H

I

F

This piece is paperboard

construction.

It is not made from wood,

but is required for the

assembly of your unit.

A

Tube

You

6

systembuild.com

Part List

Actual Size

Tube

You

Not Actual Size

(x12)

#A13410

1-3/4" flat head screw

(x4)

#A24045

screw cap

(x2)

#A11145

1/2" flat head screw

(x2)

#A11210

3/4" pan head screw

(x2)

#A11195

5/8" pan head screw

(x8)

#A80250

shelf support

(x4)

#A17300

3/4" machince screw

(x40)

#A21110

nail

(x4)

#A43100

glide

(x1)

#A55015

lock

(x2)

#89020

bumper

(x2)

#A52700

handle

(x6)

#A65640

hinge

(x1)

#A55410

latch

(x1)

#A84050

safety bracket kit

7

systembuild.com

STEP

1

Tube

You

Separate hinge by loosening screw as shown.

(x6)

#A65640

A

X2

8

systembuild.com

STEP2

Tube

You

D

C

(x1)

#A84050

safety bracket kit

(x2)

#89020

bumper

(x2)

#A11195

5/8" pan head screw

(x4)

#A43100

glide

Attach the bumper to the far side of the top (C)

with two 5/8” screws. Attach the safety bracket to

the near side of the top (C).

Press the glides into the holes in the bottom (D).

9

systembuild.com

STEP3

C

E

A

D

All finished edges are to face up.

After assembly, press the screw caps onto the screws.

(x12)

#A13410

(x4)

#A24045

Tube

You

finished side

* raw edges are shaded

10

systembuild.com

STEP

4

I

* raw edges are shaded

(x36)

#A21110

Assure that the unit is square.

Distance from corner to corner must be equal as shown.

Attach the back panel as shown nailing straight into the raw edges.

IMPORTANT!

THE BACK PANEL IS A STRUCTURAL PART OF THIS UNIT

AND MUST BE INSTALLED PROPERLY.

Carefully turn the unit onto its front.

Tube

You

11

systembuild.com

STEP

5

Tube

You

* raw edges are shaded

(x1)

#A84050

stud

wallboard

hole

Stand the unit upright and place against the wall.

Fasten the wall anchor to the wall using option 1 or 2.

Option 1: Securely screw into solid area of the wall as

shown.

Option 2: Drill a 3/16" diameter hole (5mm) in the

wallboard.

Tap the wall anchor into the hole until it is flush.

Fasten the wall bracket to the wall anchor with the screw.

option 2

option 1

12

systembuild.com

STEP6

G

H

F

(x8)

#A80250

(x6)

#A65640

Make sure the "lever" is in the upper position

when the latch is attached to the door.

(x1)

#A55410

(x2)

#A11210

G

Tube

You

13

systembuild.com

STEP

7

Loosen screw C

Adjust door.

Tighten screw C

*side view

Loosen screw C

Turn screw B to

move door.

Tighten screw C

Loosen screw A

Adjust door.

Tighten screw A

(x4)

#17300

(x1)

#A55015

(x2)

#A52700

(x2)

#A11145

B

A

C

G

H

optional

Attach the doors to the

unit and make

adjustments if needed as

shown in the detail.

Attach the handle and

lock as shown.

Tube

You

14

systembuild.com

STEP8

To lock the doors:

1. Close the left door first. Extend the barrel of the lock down into

the hole in the bottom shelf.

2. Close the right door. Insert the key into the lock and turn. This

will position the lock bar behind the left door. Remove the key.

Tube

You

15

systembuild.com

Tube

You

Maximum Loads

Warning: Risk of injury to persons - do not place a television on this furniture. This furniture is

not approved for use with a television.

Certificate of Conformity

1. This certificate applies to the Dorel Home Furnishings, Inc. product identified by this instruction manual.

2. This certificate applies to compliance of this product with the CPSC Ban on Lead-Containing Paint (16 CFR 1303).

3. This product is distributed by: Dorel Home Furnishings, Inc.

410 East First Street South

Wright City, MO 63390

636-745-3351

4. Site of Manufacture: Tiffin OH

5. See front page of instruction manual for date of manufacture.

This unit has been designed to support the maximum loads shown. Exceeding these load limits

could cause sagging, instability, product collapse, and/or serious injury.

0 lbs.

0 kg.

40 lbs.

18.1 kg.

16

systembuild.com

Register your product to receive the following:

* New trend details - sneak peek on what's new

* Surveys - have a voice within our community

* Exclusive deals and discount codes

* Quick and easy replacement part service

To register your product, visit systembuild.com

Visit your local retailer's website, rate your purchased

product and leave us some feedback!

We would like to extend a big "Thank You" to all of

our customers for taking the time to assemble this

Systembuild product, and to give us your valuable

feedback.

Tube

You

Page is loading ...

System Build 7467056COM User manual

System Build 7467056COM User manual

in other languages

Related papers

Other documents