LG LSHD3089BD Owner's manual

Type
Owner's manual
ENGLISH ESPAÑOL
OWNER'S MANUAL
HOOD
Read this owner’s manual thoroughly before operating the appliance
and keep it handy for reference at all times.
www.lg.com
LSHD3689BD LSHD3089BD
LSHD3680ST LSHD3080ST
MFL70282902_00
Copyright © 2017 LG Electronics Inc. All Rights Reserved.
2
TABLE OF CONTENTS
TABLE OF CONTENTS
3 IMPORTANT SAFETY
INSTRUCTIONS
6 PRODUCT OVERVIEW
6 Parts
6 Specifications
7 OPERATION
8 SMART FUNCTIONS
8 LG SmartThinQ Application
9 FCC Notice (For transmitter module contained in
this product)
9 FCC RF Radiation Exposure Statement
10 MAINTENANCE
10 Surface Maintenance
10 Aluminum Mesh Filters
10 Removing Mesh Filters
11 TROUBLESHOOTING
11 Before Calling for Service
13 WARRANTY
3
IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
Read and follow all instructions when using the range to prevent the risk of fire, electric
shock, personal injury, or damage. This guide does not cover all possible conditions that
may occur. Always contact your service agent or manufacturer about problems that you do
not understand.
Download this owner's manual at: http://www.lg.com
This is the safety alert symbol. This symbol alerts you to potential hazards that
can result in property damage and/or serious bodily harm or death.
All safety messages will follow the safety alert symbol and either the word
WARNING or CAUTION. These words mean:
WARNING
- Indicates a hazardous situation which, if not avoided, could result
in death or serious injury.
CAUTION
- Indicates a hazardous situation which, if not avoided, could result
in minor or moderate injury.
WARNING
To avoid the possibility of explosion or fire, do not store or use combustible, flammable
or explosive vapors and liquids (such as gasoline) inside or in the vicinity of this or
any other appliance. Also keep items that could explode, such as aerosol cans, away
from cooktop burners, ovens and range hoods. Do not store flammable or explosive
materials in adjacent cabinets or areas.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
Use this unit only in the manner intended by the manufacturer. If you have questions,
contact the manufacturer.
Before servicing or cleaning unit, switch power off at service panel and lock the
service panel door to prevent power from being switched on accidentally. When the
service panel door cannot be locked, securely fasten a prominent warning device,
such as a tag, to the service panel.
CAUTION
For general ventilating use only. DO NOT use to exhaust hazardous or explosive
materials and vapors.
STATE OF CALIFORNIA PROPOSITION 65 WARNINGS
WARNING
This product contains chemicals known to the State of California to cause cancer and
birth defects or other reproductive harm. Wash hands after handling. (US only)
4
IMPORTANT SAFETY INSTRUCTIONS
GENERAL SAFETY PRECAUTIONS
To reduce the risk of fire, electric shock, serious injury or death when using the range hood,
follow basic safety precautions, including the following:
WARNING
If you receive a damaged product, immediately contact your dealer or builder. Do not
install or use a damaged hood.
Make sure that the range hood has been properly installed and grounded by a qualified
installer according to the accompanying installation instructions. Have the installer
show you the location of the fuse or junction box so that you know where and how to
turn the power off.
Do not install, repair or replace any part of the range hood unless specifically
recommended in the literature accompanying it. A qualified service technician should
perform all other service.
To avoid the risk of electric shock, before servicing the range hood, switch power off at
the fuse or junction box and lock the electrical panel door to prevent power from being
switched on accidentally. When the electrical panel cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
To avoid the risk of electric shock, before cleaning the range hood, turn off the main
power switch.
Use the range hood only for its intended purpose as outlined in this manual. DO NOT
use this range hood to vent hazardous or explosive materials or vapors. If you have
questions, contact the manufacturer.
Do not tamper with the controls.
Never allow the filters to become blocked or clogged. Do not allow foreign objects,
such as cigarettes or napkins, to be sucked into the hood.
If the cooktop and range hood are near a window, use an appropriate window
treatment. Avoid long drapes or other window coverings that could blow over the
cooktop and hood, resulting in a fire hazard.
Always run the fan(s) whenever the cooktop is operating.
Do not leave children alone or unattended in the area where the cooktop and range
hood are in use. Never allow children to sit or stand on an appliance. Do not let
children play with a range, cooktop or range hood. Do not store items of interest to
children above or around the cooktop, range or range hood.
The minimum vertical distance between the cooktop surface and the exterior part of
the hood must be no less than 26" (66 cm). The required vertical distance may be
longer for the range or cooktop being used. Consult the range or cooktop installation
instructions for the minimum vertical distance from the appliance being used.
To reduce the risk of a range-top grease fire:
Never leave surface units unattended at high settings. Boil-overs cause smoking and
greasy spill-overs that may ignite. Heat oils slowly on low or medium settings.
Always turn hood ON when cooking at high heat or when flambéing food (i.e. Crepes
Suzette, Cherries Jubilee, Peppercorn Beef Flambé).
Clean ventilating fans frequently. Grease should not be allowed to accumulate on
fan or filter.
Use proper pan size. Always use cookware appropriate for the size of the surface
element.
5
IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
WARNING
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE-
TOP GREASE FIRE:
SMOTHER FLAMES with a close-fitting lid, cookie sheet or metal tray, then turn
off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out
immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
NEVER PICK UP A FLAMING PAN - you may be burned.
DO NOT USE WATER, including wet dish cloths or towels - a violent steam explosion
may result.
Use a fire extinguisher ONLY if:
• You have a Class ABC extinguisher, and you already know how to operate it.
• The fire is small and contained in the area where it started.
• The fire department is being called.
• You can fight the fire with your back to an exit.
READ AND SAVE THESE INSTRUCTIONS
6
PRODUCT OVERVIEW
PRODUCT OVERVIEW
Parts
1
4 5
23
1
HOOD
2
ICON TOUCH CONTROL PANEL
3
LED STRIP LIGHT
4
MESH FILTER
5
SIDE PANEL (Only for LSHD3689BD, LSHD3680ST)
Specifications
Hood Models LSHD3689BD, LSHD3680ST, LSHD3089BD, LSHD3080ST
Hood Width
LSHD3689BD, LSHD3680ST : 36 Inches
LSHD3089BD, LSHD3080ST : 30 Inches
Filters 2 pcs
Lights 1(LED Strip type)
7
OPERATION
ENGLISH
OPERATION
1 32
4
1
POWER / DELAY OFF BUTTON
Power Button Function
Button will turn power on and off for
entire hood (fan and lights).
Hood will remember the last speed and light
level it was turned off at.
(Example: Press the
button to turn off
the hood with fan speed at level 4 and lights
on high. Press the
again and the hood
will turn on with the fan speed set to 4 and the
lights on high.)
Delay Off Button Function
With the fan on, press and hold the
button for three seconds. The fan will change
to speed 1 and the 5 minute delay off timer
will start.
+ LEDs will illuminate
and slowly blink in accordance with the time
remaining until the fan and lights automatically
turn off.
Pressing the
button while the Delay
Off Function is enabled will turn the hood off
and cancel the Delay Off Function.
2
SPEED SELECTION BUTTON
Fan Speed Decrease Button
Press this button to decrease fan speed. 5, 4,
3, 2, 1.
If fan is On at level 1 and this button is
pressed, fan will power Off.
Fan Speed Increase Button
Press this button to increase fan speed. Fan
On, 1, 2, 3, 4, 5.
If hood is Off and this button is pressed, fan
will turn On at level 1.
3
LIGHT BUTTON
The light has two levels: High and Low.
From off, press one time for High. Press again
for Low. Press again to power lights off.
Press and hold the Light button for 3 seconds
to connect to a home Wi-Fi network. See
page 8 for more information.
4
DISPLAY INDICATORS
Mesh Filter Clean Reminder (always enabled)
After 30 hours of fan usage, the
button
indicator will begin to slowly blink indicating it
is time to clean the mesh filters.
To reset: With hood off: hold the
button
for three seconds. All LED indicators will blink
two times confirming the 30 hour timer has
been reset.
Charcoal Filter Replace Indicator
(disabled by default, must be enabled if
recirculating hood)
To enable Charcoal Filter Replacement
Reminder:
With hood off, hold
button and
button simultaneously for three seconds.
All LED indicators will illuminate for three
seconds confirming the Charcoal Filter
Replace Reminder is enabled.
To disable Charcoal Filter Replacement
Reminder:
With hood off, hold
button and
button simultaneously for three seconds.
All LED indicators will blink two times
confirming the Charcoal Filter Replace
Reminder is disabled.
After 120 hours of fan usage the
button
will slowly blink indicating the charcoal filters
need replacement.
To reset: With hood off, hold the
button
for three seconds. All LED indicators will blink
two times confirming the 120 hour timer has
been reset.
8
SMART FUNCTIONS
SMART FUNCTIONS
LG SmartThinQ Application
The LG SmartThinQ application allows you to
communicate with the appliance using a smartphone.
Before Using LG SmartThinQ
For appliances with the or logo
1
Use a smartphone to check the strength of
the wireless router (Wi-Fi network) near the
appliance.
If the distance between the appliance and the
wireless router is too far, the signal strength
becomes weak. It may take a long time to
register or installation may fail.
2
Turn off the Mobile data or Cellular Data on
your smartphone.
3
Connect your smartphone to the wireless router.
NOTE
To verify the Wi-Fi connection, check that Wi-Fi
icon on the control panel is lit.
The appliance supports 2.4 GHz Wi-Fi networks
only. To check your network frequency, contact
your Internet service provider or refer to your
wireless router manual.
LG SmartThinQ is not responsible for any
network connection problems or any faults,
malfunctions, or errors caused by network
connection.
The surrounding wireless environment can
make the wireless network service run slowly.
If the appliance is having trouble connecting
to the Wi-Fi network, it may be too far from
the router. Purchase a Wi-Fi repeater (range
extender) to improve the Wi-Fi signal strength.
The network connection may not work properly
depending on the Internet service provider.
The Wi-Fi connection may not connect or may
be interrupted because of the home network
environment.
If the appliance cannot be registered due to
problems with the wireless signal transmission,
unplug the appliance and wait about a minute
before trying again.
If the firewall on your wireless router is enabled,
disable the firewall or add an exception to it.
The wireless network name (SSID) should be a
combination of English letters and numbers. (Do
not use special characters.)
Smartphone user interface (UI) may vary
depending on the mobile operating system (OS)
and the manufacturer.
If the security protocol of the router is set to
WEP, network setup may fail. Change the
security protocol (WPA2 is recommended), and
register the product again.
Installing the LG SmartThinQ
Application
Search for the LG SmartThinQ application from the
Google Play Store or Apple App Store on a smart
phone. Follow instructions to download and install the
application.
NOTE
If you choose the simple login to access the LG
SmartThinQ application, you must go through
the appliance registration process each time
you change your smartphone or reinstall the
application.
9
SMART FUNCTIONS
ENGLISH
LG SmartThinQ Application Features
For appliances with the or logo
Settings
Allows you to set various options on the hood and in
the application.
Monitoring
Use this function to check the current status from one
screen.
NOTE
If you change your wireless router, your
Internet service provider or your password after
registering the appliance, delete it from the LG
SmartThinQ SettingsEdit Product and
register again.
This information is current at the time of
publication. The application is subject to change
for product improvement purposes without
notice to users.
Open Source Software Notice
Information
To obtain the source code under GPL, LGPL, MPL,
and other open source licenses, that is contained in
this product, please visit http://opensource.lge.com.
In addition to the source code, all referred license
terms, warranty disclaimers and copyright notices are
available for download.
LG Electronics will also provide open source code
to you on CD-ROM for a charge covering the cost
of performing such distribution (such as the cost of
media, shipping, and handling) upon email request
to [email protected]. This offer is valid for a
period of three years after our last shipment of this
product. This offer is valid to anyone in receipt of this
information.
Wireless module (LCW-003) Specifications
Frequency Range 2412~2462 MHz
Output Power (max.)
IEEE 802.11 b : 17.56 dBm
IEEE 802.11 g : 25.53 dBm
IEEE 802.11 n : 25.29 dBm
FCC Notice (For transmitter
module contained in this
product)
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and the receiver.
Connect the equipment to an outlet on a circuit
different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference
and
2) this device must accept any interference received,
including interference that may cause undesired
operation of the device.
Any changes or modifications in construction of this
device which are not expressly approved by the party
responsible for compliance could void the user’s
authority to operate the equipment.
FCC RF Radiation Exposure
Statement
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This
transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
This equipment should be installed and operated with
minimum distance 20 cm (7.8 inches) between the
antenna and your body. Users must follow the specific
operating instructions for satisfying RF exposure
compliance.
10
MAINTENANCE
MAINTENANCE
Surface Maintenance
Clean periodically with hot soapy water and a
clean cotton cloth. Do not use corrosive or abrasive
detergent, or steel wool/scouring pads which will
scratch and damage surface. Do not use products
containing chlorine bleach or citrus-based cleaners.
For heavier soil use liquid degreaser.
After cleaning, you may use non-abrasive stainless
steel polish or cleaners to polish and buff out the
stainless luster and grain. Using a clean microfiber or
cotton cloth, scrub lightly and with the grain.
Aluminum Mesh Filters
The aluminum mesh filters installed by the factory are
intended to filter out residue and grease from cooking.
They don't need to be replaced on a regular basis, as
long as they are kept clean.
Remove and clean by hand or in dishwasher on low
heat. Spray degreasing detergent and leave to soak if
heavily soiled.
Dry filters and re-install before using hood.
Removing Mesh Filters
1
Push handle on filter toward back of range hood.
2
Pivot the front of the filter down and pull the filter
forward to remove it.
Follow these steps in reverse to reassemble the
filter.
11
TROUBLESHOOTING
ENGLISH
TROUBLESHOOTING
Before Calling for Service
Symptoms Possible Causes / Solutions
After installation, the
unit doesn’t work.
The power source is not turned ON.
- Make sure the circuit breaker and the unit’s power is ON.
The power cord and the cable locking connector are not connected properly.
- Make sure the power cord is properly connected to the unit.
Lights work, but
blower is not turning.
The thermally protected system detects if the blower is too hot to operate and
shuts the blower down.
- The blower will function properly after the thermally protected system cools
down.
The unit is vibrating.
The blower is not securely in place.
- Tighten the screws holding the blower in place.
Damaged blower wheel.
- Call for service.
The hood is not secured in place.
- Check the installation of the hood.
The blower is working,
but the lights are not.
Call for service.
The speed levels of
the blower sound the
same.
Using the wrong size of ducting.
- Change the ducting to at least 8" round or 3-1/4" x 10" rectangular for single
blower or 10" round for dual blower.
The hood is not
venting out properly.
The hood might be hanging too far above the cook top.
- Adjust the distance between the cook top and the bottom of the hood to within
26" to 36".
The wind from the opened windows or opened doors in the surrounding area are
affecting the ventilation of the hood.
- Close all windows and doors to eliminate the outside wind flow.
Blockage in the duct opening or duct work.
- Clear any blockages from the duct work or duct opening.
The direction of duct opening is against the wind.
- Adjust the duct opening direction.
Using the wrong size of ducting.
- Change the ducting to correct size.
Mesh filter is
vibrating.
Mesh filter is loose.
- Change the metal filter.
The unit turns on by
itself.
A spot light or kitchen lamp is shining directly onto the switch controls.
- The switch controls are light sensitive. A light source aimed directly at the
switch controls may disrupt switch functions.
12
TROUBLESHOOTING
Symptoms Possible Causes / Solutions
Trouble connecting
appliance and
smartphone to Wi-Fi
network
The password for the Wi-Fi network was entered incorrectly.
- Delete your home Wi-Fi network in the application and begin the registration
process again.
Mobile data for your smartphone is turned on.
- Turn off the Mobile data on your smartphone before registering the appliance.
The wireless network name (SSID) is set incorrectly.
- The wireless network name (SSID) should be a combination of English letters
and numbers. (Do not use special characters.)
The router frequency is not 2.4 GHz.
- Only a 2.4 GHz router frequency is supported. Set the wireless router to 2.4
GHz and connect the appliance to the wireless router. To check the router
frequency, check with your Internet service provider or the router manufacturer.
The distance between the appliance and the router is too far.
- If the appliance is too far from the router, the signal may be weak and the
connection may not be configured correctly. Move the router closer to the
appliance or purchase and install a Wi-Fi repeater.
13
WARRANTY
ENGLISH
WARRANTY (USA)
Should your LG Electric Range fail due to a defect in materials or workmanship under normal home use, during
the warranty period set forth below, LG will at its option repair or replace the product. This limited warranty is
valid only to the original retail purchaser of the product and applies only when purchased and used within the
United States including U.S. Territories. Proof of original retail purchase is required to obtain warranty service
under this limited warranty.
Warranty Period Scope of Warranty HOW SERVICE IS HANDLED
Two (2) years from date of
original retail purchase
Parts and Labor
LG will provide parts and labor to repair or replace
defective parts.
Replacement products and parts are warranted for the remaining portion of the original warranty period or
ninety (90) days, whichever is greater.
Replacement products and parts may be new or remanufactured.
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING WITHOUT
LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO
THE EXTENT ANY IMPLIED WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE
EXPRESS WARRANTY PERIOD ABOVE. NEITHER THE MANUFACTURER NOR ITS U.S. DISTRIBUTOR
SHALL BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE
DAMAGES OF ANY NATURE, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR PROFITS, OR
ANY OTHER DAMAGE WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how
long an implied warranty lasts, so the above exclusion or limitation may not apply to you. This warranty gives you
specific legal rights and you may also have other rights that vary from state to state.
THIS LIMITED WARRANTY DOES NOT COVER:
Service trips to deliver, pick up, or install or repair the product; instruction to the customer on operation of
the product; repair or replacement of fuses or correction of wiring or plumbing, or correction of unauthorized
repairs/installation.
Failure of the product to perform during power failures and interruptions or inadequate electrical service.
Damage caused by leaky or broken water pipes, frozen water pipes, restricted drain lines, inadequate or
interrupted water supply or inadequate supply of air.
Damage resulting from operating the Product in a corrosive atmosphere or contrary to the instructions outlined
in the Product’s owner’s manual.
Damage to the Product caused by accidents, pests and vermin, lightning, wind, fire, floods, or acts of God.
Damage or failure caused by unauthorized modification or alteration, or if it is used for other than the intended
purpose, or any water leakage where the unit was not properly installed.
Damage or failure caused by incorrect electrical current, voltage, or plumbing codes, commercial or industrial
use, or use of accessories, components, or consumable cleaning products that are not approved by LG.
Damage caused by transportation and handling, including scratches, dents, chips, and/or other damage to the
finish of your product, unless such damage results from defects in materials or workmanship and is reported
within one (1) week of delivery.
Damage or missing items to any display, open box, discounted, or refurbished Product.
Products with original serial numbers that have been removed, altered, or cannot be readily determined. Model
and Serial numbers, along with original retail sales receipt, are required for warranty validation.
Increases in utility costs and additional utility expenses.
Repairs when your Product is used in other than normal and usual household use (e.g. commercial use, in
offices and recreational facilities) or contrary to the instructions outlined in the Product’s owner’s manual.
Costs associated with removal of your Product from your home for repairs.
14
WARRANTY
The removal and reinstallation of the Product if it is installed in an inaccessible location or is not installed in
accordance with published installation instructions, including LG’s owner’s and installation manuals.
Damage resulting from misuse, abuse, improper installation, repair, or maintenance. Improper repair includes
use of parts not approved or specified by LG.
OBTAIN WARRANTY SERVICE AND ADDITIONAL INFORMATION
If you do not have access to the internet and you need assistance using your product or you would like to
schedule service, you may contact LG Electronics at the number below.
For assistance or service, call 1-800-243-0000.
If you need further assistance, you can write to LG with any questions or concerns at the address below:
LG Electronics, 201 James Record Road, Huntsville, Alabama 35813
For additional product information, visit our website at http://www.lg.com
ESPAÑOL
MANUAL DEL PROPIETARIO
CAMPANA
Lea detenidamente el manual del propietario antes de poner el aparato en
funcionamiento y consérvelo a mano en todo momento para su referencia.
www.lg.com
LSHD3689BD LSHD3089BD
LSHD3680ST LSHD3080ST
MFL70282902_00
Copyright © 2017 LG Electronics Inc. Todos los Derechos Reservados.
2
ÍNDICE
ÍNDICE
3 INSTRUCCIONES IMPORTANTES DE
SEGURIDAD
6 DESCRIPCIÓN GENERAL DEL
PRODUCTO
6 Piezas
6 Especificaciones
7 FUNCIONAMIENTO
8 FUNCIONES INTELIGENTES
8 Aplicación LG SmartThinQ
9 Aviso de la FCC (para el módulo transmisor contenido
en este producto)
9 Declaración sobre exposición a la radiación de RF de
la FCC
10 MANTENIMIENTO
10 Mantenimiento de la superficie
10 Filtros de malla de aluminio
10 Extraer los filtros de malla
11 SOLUCIÓN DE PROBLEMAS
11 Antes de llamar al servicio técnico
13 GARANTÍA
3
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Español
INSTRUCCIONES IMPORTANTES DE
SEGURIDAD
Lea y siga todas las instrucciones cuando utilice la cocina para evitar riesgos de incendios, descargas
eléctricas, lesiones personales o daños. Esta guía no incluye todas las situaciones posibles que
podrían ocurrir. Siempre comuníquese con su agente de servicio técnico o con el fabricante cuando
haya problemas que no comprenda.
Descargue este manual en: http://www.lg.com
Este es el símbolo de alerta de seguridad. Este símbolo le advierte sobre posibles riesgos
que pueden ocasionar daños materiales, lesiones personales graves o la muerte.
El símbolo de alerta de seguridad siempre estará acompañado de las palabras
"ADVERTENCIA" o "PRECAUCIÓN". Estos términos significan lo siguiente:
ADVERTENCIA
- Indica una situación peligrosa que, de no evitarse, podría
causar lesiones graves o la muerte.
PRECAUCIÓN
- Indica una situación peligrosa que, de no evitarse, podría
causar lesiones leves o moderadas.
ADVERTENCIA
Para evitar que se produzcan explosiones o incendios, no almacene ni use líquidos o vapores
combustibles, inflamables o explosivos (como por ejemplo, gasolina) dentro o cerca de este o
cualquier otro artefacto. Además, mantenga cualquier artículo que pueda explotar, como, por
ejemplo, latas de aerosol, alejado de los quemadores de la cocina, del horno y de la campana
extractora. No almacene materiales explosivos o inflamables en áreas o alacenas cercanas.
PARA REDUCIR EL RIESGO DE INCENDIO, DESCARGAS ELÉCTRICAS O LESIONES
PERSONALES, TENGA EN CUENTA LO SIGUIENTE:
Use esta unidad solamente del modo previsto por el fabricante. Si tiene alguna pregunta,
póngase en contacto con el fabricante.
Antes de limpiar o realizarle mantenimiento a la unidad, apáguela desde el panel de servicio
y bloquee la puerta del panel de servicio para evitar que la unidad se encienda por accidente.
En caso de que la puerta del panel de servicio no se pueda bloquear, coloque un dispositivo
de advertencia bien visible y firmemente sujeto, como, por ejemplo, una etiqueta, en el panel
de servicio.
PRECAUCIÓN
Solo para uso de ventilación general. NO lo utilice para la extracción de materiales y vapores
peligrosos o explosivos.
ADVERTENCIAS DE LA PROPUESTA 65 DEL ESTADO DE
CALIFORNIA
ADVERTENCIA
Este producto contiene químicos conocidos por el estado de California por causar cáncer,
malformaciones de nacimiento u otros daños reproductivos. Lávese bien las manos después
de su manipulación.(Solo EEUU)
4
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
PRECAUCIONES GENERALES DE SEGURIDAD
Para reducir el riesgo de incendio, descargas eléctricas, lesiones graves o muerte al usar esta
campana extractora, siga las precauciones de seguridad básicas, incluidas las siguientes:
ADVERTENCIA
Si recibe un producto dañado, póngase en contacto inmediatamente con el distribuidor o el
constructor. No instale ni utilice una campana dañada.
Asegúrese de que un instalador calificado instale y conecte a tierra su campana extractora de
acuerdo con las instrucciones de instalación suministradas. Haga que el instalador le muestre
la ubicación de la caja de empalmes o fusibles para que usted sepa dónde y cómo apagar el
artefacto.
No instale, repare o reemplace ninguna pieza de la campana extractora, salvo que esto
se recomiende específicamente en la documentación suministrada. Toda otra tarea de
mantenimiento debe ser realizada por un técnico calificado.
Para evitar el riesgo de descargas eléctricas, antes de realizarle mantenimiento a la campana
extractora, apáguela desde la caja de empalmes o fusibles y bloquee la puerta del panel
eléctrico para evitar que la unidad se encienda por accidente. En caso de que el panel del panel
eléctrico no se pueda bloquear, coloque un dispositivo de advertencia bien visible y firmemente
sujeto, como, por ejemplo, una etiqueta, en el panel de servicio.
Para evitar el riesgo de descarga eléctrica, antes de limpiar la campana extractora, apague el
interruptor principal.
Use la campana extractora solo para el propósito previsto, tal como se describe en este manual.
NO utilice esta campana para la extracción de materiales y vapores peligrosos o explosivos. Si
tiene alguna pregunta, póngase en contacto con el fabricante.
No manipule indebidamente los controles.
Nunca permita que los filtros se bloqueen u obstruyan. No permita que objetos extraños, tales
como cigarrillos o servilletas, sean aspirados por la campana.
Si la cocina y la campana extractora se encuentran cerca de una ventana, asegúrese de que
la ventana cumpla con las condiciones adecuadas. Evite que la ventana tenga cortinas largas
u otras cubiertas que podrían volar sobre la superficie de cocción y la campana, ya que esto
puede significar un riesgo de incendio.
Siempre ponga en funcionamiento el/los ventilador(es) cuando esté utilizando la superficie de
cocción.
No deje niños solos o sin vigilancia en el área donde se estén utilizando la superficie de cocción
y la campana extractora. Nunca permita que los niños se sienten en un artefacto o se suban a
él. No permita que los niños jueguen con una cocina, una superficie de cocción o una campana
extractora. No almacene artículos de interés para los niños encima o alrededor de la superficie
de cocción, la cocina o la campana extractora.
La distancia vertical mínima entre la superficie de la cocina y la parte exterior de la campana no
debe ser menor de 26" (66 cm). La distancia vertical puede tener que ser mayor según la cocina
o la superficie de cocción que se esté utilizando. Consulte las instrucciones de instalación de
la cocina o la superficie de cocción para conocer la distancia mínima vertical desde el artefacto
que se utilice.
5
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Español
ADVERTENCIA
Para reducir el riesgo de incendio provocado por grasa en la superficie de la cocina:
Nunca deje las hornallas sin supervisión en configuraciones de altas temperaturas. Los
derramamientos por ebullición producen humo y los derrames de grasa pueden arder.
Caliente las grasas y los aceites lentamente y en configuraciones de temperatura bajas o
medias.
Siempre encienda la campana cuando cocine a altas temperaturas o cuando realice
flambeados (por ej., flambeado de carne a la pimienta, crepes Suzette, cerezas Jubilee).
Limpie los ventiladores regularmente. No debe dejar que se acumule grasa en el ventilador o
el filtro.
Use el tamaño adecuado de sartén. Siempre utilice utensilios de cocina de dimensiones
adecuadas para el tamaño de la hornalla.
PARA REDUCIR EL RIESGO DE LESIONES PERSONALES EN CASO DE UN INCENDIO
PROVOCADO POR GRASA EN LA SUPERFICIE DE LA COCINA:
SOFOQUE LAS LLAMAS con una tapa que ajuste bien, una asadera o una bandeja de metal
y luego apague el quemador. SEA CUIDADOSO PARA EVITAR QUEMADURAS. Si las llamas
no se apagan inmediatamente, EVACUE Y LLAME A LOS BOMBEROS.
NUNCA TOME UNA OLLA EN LLAMAS, puede quemarse.
NO USE AGUA, lo que incluye paños de cocina o toallas húmedas: puede producirse una
violenta explosión de vapor.
Use un extintor SOLAMENTE si:
• Tiene un extintor clase ABC y ya sabe cómo operarlo.
• El fuego es pequeño y se halla contenido en el área donde comenzó.
• Ya llamó a los bomberos.
• Puede intentar apagar el fuego manteniendo su espalda hacia una salida.
LEA Y GUARDE ESTAS INSTRUCCIONES
6
DESCRIPCIÓN GENERAL DEL PRODUCTO
DESCRIPCIÓN GENERAL DEL PRODUCTO
Piezas
1
4 5
23
1
CAMPANA
2
PANEL DE CONTROL TÁCTIL CON ICONOS
3
LUZ LED
4
FILTROS DE MALLA
5
PANEL LATERAL (solo para LSHD3689BD, LSHD3680ST)
Especificaciones
Modelos de campana LSHD3689BD, LSHD3680ST, LSHD3089BD, LSHD3080ST
Ancho de la campana
LSHD3689BD, LSHD3680ST : 36 pulgadas
LSHD3089BD, LSHD3080ST : 30 pulgadas
Filtros 2 pzas.
Luces 1 (tipo tira LED)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

LG LSHD3089BD Owner's manual

Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages