Rust-Oleum Universal 249132 User guide

Brand: Rust-Oleum Universal

Model: 249132

Type: User guide

This manual is also suitable for

TECHNICAL DATA UNI-02

UNIVERSAL

METALLIC SPRAYS

Form: GDH-142

Rev.: 0129153

.DESCRIPTION AND USES .

Universal

Metallic Sprays are versatile all-surface paints

that provide a durable protective coating with excellent

resistance to rust, and excellent resistance to abrasion,

fading, chipping, and dulling. These sprays apply easily,

provide excellent coverage and dry fast to a tough

attractive finish. Universal Metallic Sprays are ideal for

plastic, wood, metal, wicker, and aluminum. Universal

features a comfort grip trigger that reduces fatigue caused

by continuous spraying and an any-angle tip which allows

you to spray at any angle. Some plastics made of

polyethylene such as Little Tikes

children’s products are

manufactured in such a way that may hinder maximum

paint adhesion. Test paint in an inconspicuous area first.

Not for use on galvanized metal.

.PRODUCTS .

SKU Description

245220 Titanium Silver

245221 Pure Gold

249130 Satin Nickel

249131 Oil Rubbed Bronze

258199 Dark Bronze

261401 Aged Copper

261414 Rustic Mist

267298 White

271471 Flat Chestnut

271472 Flat Burnished Amber

271473 Flat Soft Iron

271474 Flat Antique Nickel

285073 Aged Metallic Rust

PAINTING CONDITIONS .

Use outdoors or in a well ventilated area such as an open

garage. Use when temperature is between 50-90ºF (10-

32ºC) and humidity is below 65% to ensure proper drying.

Do not use on objects that may exceed 200ºF (93ºC)

surface temperature. Do not apply to galvanized steel.

Avoid spraying in very windy and dusty conditions. Cover

surrounding area to protect from spray mist.

PRODUCT APPLICATION .

SURFACE PREPARATION

Remove all dirt, grease, oil, salt and chemical

contaminants by washing the surface with a commercial

detergent, or other suitable cleaning method. Rinse with

fresh water and allow to thoroughly dry. Remove loose

paint and rust with a wire brush or sandpaper. Previously

coated surfaces must be sound and in good condition.

Smooth, hard, or glossy finishes should be scarified by

sanding to create a surface profile.

PRODUCT APPLICATION (cont.) .

WARNING! If you scrape, sand or remove old paint, you

may release lead dust. LEAD IS TOXIC. EXPOSURE TO

LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS

BRAIN DAMAGE, ESPECIALLY IN CHILDREN.

PREGNANT WOMEN SHOULD ALSO AVOID

EXPOSURE. Wear a NIOSH-Approved respirator to

control lead exposure. Clean up carefully with a HEPA

vacuum and a wet mop. Before you start, find out how to

protect yourself and your family by contacting the National

Lead Information Hotline at 1-800-424-LEAD or log on to

ww.epa.gov/lead.

APPLICATION

Shake can vigorously for one minute after the mixing ball

begins to rattle. If mixing ball fails to rattle DO NOT

STRIKE CAN. Contact Rust-Oleum. Shake often during

use. Prior to use, slide off the red safety clip from the

trigger. Hold can upright 8-12” from surface and spray in a

steady back-and-forth motion, slightly overlapping each

stroke. Keep the can the same distance from the surface.

Keep the can in motion while spraying. Apply two or

more moderate coats at moderate speed to avoid drips

and runs. Do not use near open flame.

DRY & RECOAT

Dry and recoat times are based on 70ºF and 50% relative

humidity. Allow more time at cooler temperatures. Dries to

touch in 30 minutes, to handle in 1 hour, and is fully dry in

24 hours. Recoat within 1 hour or after 48 hours.

CLEAN-UP

When finished spraying, wipe off tip before storing. Clean

up wet paint with xylene or mineral spirits. Properly

discard empty container. Do not burn or place in home

trash compactor.

CLOGGING

If the valve clogs, twist and pull off spray tip and rinse in a

solvent such as mineral spirits. Do not insert any object

into can valve opening.

TECHNICAL DATA

UNIVERSAL METALLIC SPRAYS

Rust-Oleum Corporation Form: GDH-142

11 Hawthorn Parkway Phone: 877•385•8155 Rev.: 012915

Vernon Hills, Illinois 60061 www.rustoleum.com

An RPM Company

PHYSICAL PROPERTIES .

Resin Type

Modified Alkyd

Pigment Type

Varies with Color

Solvents

Acetone, Ketone blend

MIR

1.9 Max

Fill Weight

11 ounces

Recommended Dry Film Thickness

(DFT) per Coat

1.0-2.0 mils

(25-50µ)

Practical Coverage at Recommended

DFT (assumes 15% material loss)

10-15 sq. ft./can

(0.9- 1.4 m

/can)

Dry Times at 70-80°F

(21-27°C) and 50%

Relative Humidity

Touch

30 minutes

Handle

1 hour

Recoat

Within 1 hour or after 48 hours

Dry Heat Resistance

200ºF (94ºC)

Shelf Life

5 years

Flash Point

-156ºF (-104ºC)

Safety Information

For additional information, see MSDS.

The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The statements of this

literature do not constitute a warranty, express, or implied, as to the performance of these products. As conditions and use of our materials are beyond our

control, we can guarantee these products only to conform to our standards of quality, and our liability, if any, will be limited to replacement of defective