Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Introduction
Congratulations on your purchase and welcome to Philips! To fully benet
from the support that Philips offers, register your product at www.philips.
com/welcome.
This blender has been developed to condently handle a broad variety of
ingredients and recipes in one go and to deliver a long-lasting performance.
Its unique double-blade blending system and oval-shaped glass jar gives you
a perfect end results in just seconds.
General description (Fig. 1)
A Graduated measuring cup
B Lid
C Glass blender jar with two integrated blade units
D Motor unit
E Pulse switch
F Speed selector
G Cord storage and power cord
Important
Read this user manual carefully before you use the appliance and save it for
future reference.
General
Danger
- Never immerse the motor unit in water or any other liquid, nor rinse it
under the tap. Use only a moist cloth to clean the motor unit.
Warning
- Check if the voltage indicated on the appliance corresponds to the local
mains voltage before you connect the appliance.
- Only connect the appliance to an earthed wall socket.
- Do not use the appliance if the plug, the mains cord or other parts are
damaged.
ENGLISH
- If the mains cord is damaged, you must have it replaced by Philips, a
service centre authorised by Philips or similarly qualied persons in
order to avoid a hazard.
- This appliance is intended for household use only. If the appliance is
used improperly or for professional or semi-professional purposes or if
it is not used according to the instructions in the user manual, the
guarantee becomes invalid and Philips refuses any liability for damage
caused.
- This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety.
- Children should be supervised to ensure that they do not play with the
appliance.
- Never let the appliance run unattended.
- Never reach into the jar with your ngers or an object (e.g. a spatula)
while the blender is running.
- If the blades get stuck, switch off and unplug the appliance before you
remove the ingredients that block the blades.
- Never use the blender jar to switch the appliance on and off.
- Do not touch the cutting edges of the blades when you clean the
blender jar. The cutting edges are very sharp and you could easily cut
your ngers on them.
Caution
- Always unplug the appliance before you assemble, disassemble or make
adjustments to any of the parts.
- Never use any accessories or parts from other manufacturers or that
Philips does not specically recommend. If you use such accessories or
parts, your guarantee becomes invalid.
- Do not exceed the maximum level indicated on the blender jar.
- To prevent spillage, do not put more than 1.5 litres of liquid in the
blender jar, especially when you process at a high speed. Do not put
more than 1.25 litres in the blender jar when you process hot liquids or
ingredients that tend to foam.
- Never ll the blender jar with ingredients hotter than 80ºC/175°F.
6
Pulse switch
Note: You can only use the pulse switch when the speed selector is in pulse-
activation position P or when the speed selector is set to a speed between 1
and 4.
- Push the pulse switch to PULSE and hold it in this position when you
want to process ingredients very briey (Fig. 4).
, When you push the pulse switch to PULSE and hold it in this
position, the blender starts to operate at the highest speed.
, As soon as you release the pulse switch, it jumps back to its original
position.
, When the blender was set to PULSE from the pulse-activation
position P, it stops when you release the pulse switch. When the
blender operated at a speed between 1 and 4 before you set it to
PULSE, it starts to run at this speed again when you release the pulse
switch.
Note: The pulse switch does not work when the speed selector is in the off
position 0.
AUTO position
The AUTO position has a unique speed prole to easily process any recipe.
The blender automatically increases its speed in 15 seconds to the
maximum speed and then keeps running at this speed. Select the AUTO
setting when processing smoothies or thick soups, when blending tomatoes
or when dealing with other challenging jobs. It is recommended to use the
AUTO position for small amounts to avoid splashing.
Blender
The blender is intended for pureeing and blending. With the blender you
can prepare soups, sauces, milk shakes and batters.You can also use the
blender to process vegetables and fruits.
Preparing the blender for use
1 Place the blender jar on the motor unit (Fig. 5).
You can only place the blender jar on the motor unit when the handle
points to the right.
2 Put the plug in the wall socket.
ENGLISH 7
- If food sticks to the wall of the blender jar, switch off the appliance and
unplug it. Then use a spatula to remove the food from the wall.
- Always make sure the lid is assembled properly on the blender jar and
the measuring cup is inserted properly in the lid before you switch on
the appliance.
Electromagnetic elds (EMF)
This Philips appliance complies with all standards regarding electromagnetic
elds (EMF). If handled properly and according to the instructions in this
user manual, the appliance is safe to use based on scientic evidence
available today.
Built-in safety lock
This feature ensures that you can only switch on the appliance if you have
properly assembled the blender jar on the motor unit. If the blender jar is
correctly assembled, the built-in safety lock will be unlocked.
Before rst use
1 Thoroughly clean the parts that come into contact with food before
you use the appliance for the rst time (see chapter ‘Cleaning’).
2 For hygiene reasons, put fresh water in the blender jar and let the
appliance run for 30 seconds. Then pour out the water.
Using the appliance
Speed control
Your blender is equipped with a speed selector and a pulse switch.
- The speed selector has 5 speeds, an AUTO position, a pulse-activation
position P and an off position 0.
- If you want to use a speed between 1 and 5, turn the speed selector to
the desired speed position. The power-on light lights up green (Fig. 2).
- When you turn the speed selector to the pulse-activation position P, the
power-on light lights up green. (Fig. 3)
Using the blender
1 Put the ingredients in the blender jar.
2 Place the lid on the blender jar (Fig. 6).
Push the lid down rmly to close it.
3 Insert the measuring cup into the opening in the lid (Fig. 7).
4 Turn the speed selector to select a speed.
Do not let the appliance run for more than 3 minutes at a time. If you
have not nished processing after 3 minutes, switch off the appliance. Let
the appliance cool down for one minute before you let the appliance run
again.
5 Before you open the lid, set the speed selector to 0 to switch off the
appliance.
After using the blender
1 Unplug the appliance.
2 Remove the lid with the measuring cup from the blender jar.
3 Remove the blender jar from the motor unit.
4 Always clean the removable parts immediately after use.
Tips
- Cut solid ingredients into smaller pieces before you put them in the
blender jar.
- Do not process a large quantity of solid ingredients at the same time. In
that case, process the ingredients in a series of small batches.
Measuring cup
You can use the measuring cup to measure ingredients.
Cleaning
Always clean the removable parts immediately after use.
Avoid touching the blades. The blades are very sharp.
ENGLISH8
1 Unplug the appliance.
2 Disassemble all removable parts before you clean them. (Fig. 8)
3 Clean all removable parts in the dishwasher or in warm water with
some washing-up liquid.
All parts except the motor unit are dishwasher-proof.
4 Clean the motor unit with a moist cloth.
Never immerse the motor unit in water or any other liquid, nor rinse it
under the tap.
Do not use abrasive cleaning agents, scourers, alcohol etc. to clean the
motor unit.
Quick-cleaning the blender jar
1 Pour lukewarm water (500ml-700ml) and some washing-up liquid into
the blender jar.
2 Place the lid on the blender jar and insert the measuring cup into the
hole in the lid.
3 Plug in the appliance.
4 Put the blender jar on the motor unit.
5 Press the pulse button to switch on the appliance and hold it for a
few seconds.
6 Release the pulse button and unplug the appliance.
7 Remove the blender jar from the motor unit, take off the lid and rinse
the blender jar with clean water.
Storage
- To store the mains cord, wind it round the reel in the bottom of the
appliance.
- 50g cooked rice
- 400g potatoes
- 200g green beans
- 450ml milk
1 Peel the potatoes and cut them into pieces of approximately 4x4cm.
2 Cut the chicken breast into chunks of approximately 4x4cm.
3 Roast the chunks of chicken until they are well done.
4 Cook the green beans and the potatoes for 20 minutes.
5 Warm the milk.
6 Put the cooked and still warm ingredients in the blender jar in the
order mentioned above and mix them for 1 minute.
Note: Do not process more than the quantities mentioned above at the same
time.
Note: Let the appliance cool down to room temperature before you process the
next batch.
Frequently asked questions
This chapter lists the questions most frequently asked about the appliance. If
you cannot nd the answer to your question, contact the Consumer Care
Centre in your country.
Question Answer
Can I clean all
removable
parts in the
dishwasher?
Yes, all parts except the motor unit are dishwasher-
proof.
The appliance
does not work.
What should I
do?
Please check if you have plugged in the appliance. Also
check if the blender jar is assembled properly and if
the handle of the jar points to the right.
ENGLISH 9
Environment
- Do not throw away the appliance with the normal household waste at
the end of its life, but hand it in at an ofcial collection point for
recycling. By doing this, you help to preserve the environment (Fig. 9).
Guarantee & service
Exceptional guarantee & service
You have bought a culinary tool for life and we want to ensure that
you remain satised. We would like you to register your purchase, so
that we can stay in contact with you and you can receive additional
services and benets from us. Register within 3 months of purchase
to receive benets including:
- 5 year product guarantee (and 15 year motor guarantee).
- Fresh ideas for recipes via e-mail
- Tips and tricks to use and maintain your Robust product
- All the latest news on Robust Collection
The only thing you need to do to register your new product is visit
www.philips.com/kitchen or call your local Freephone Philips consumer
care hotline (United Kingdom: 0800 331 60 15). If you have questions about
your culinary tool (usage, maintenance, accessories etc) you can either
consult our on line support at www.philips.com/kitchen or call your local
hotline.
We have put all the maximum effort in developing, testing and designing this
high quality product. However in the unfortunate case that your
product needs repair, please call your local Philips consumer care hotline.
They will help you with arranging any necessary repairs in a minimum time
with maximum convenience - they can arrange a courier to come to your
home to collect your product and bring it back when it is repaired.
This way you can continue to enjoy your delicious homemade cooking.
Recipes
Chicken and vegetable dish for babies (6 portions)
When you prepare baby food, it is important to use fresh ingredients.
Ingredients:
- 300g chicken breast
Question Answer
What does
‘pulse’ mean?
When you push the pulse switch to PULSE and hold it
in this position, the appliance runs at its highest speed.
As soon as you release the pulse switch, the switch
jumps back to its original position. When the blender
was set to PULSE from the pulse-activation position P,
it stops when you release the pulse switch. When the
blender operated at speed 1 to 4, it starts to run
again at this speed when you release the pulse switch.
The pulse switch gives you more control over the
processing job and is also very useful when you want
to process ingredients very briey.
The pulse
switch does not
work. What
should I do?
Check if the appliance is plugged in and the speed
selector is in pulse-activation position P. You can also
use the pulse switch when the speed selector is set to
a speed between 1 and 4. The pulse switch does not
work when the speed selector is set to the off
position 0 or to speed 5.
What is the
AUTO setting
of the speed
selector for?
When the speed selector is set to AUTO, the
blender automatically speeds up to the maximum
speed within 15 seconds and then keeps running
at the maximum speed.
Can I pour
boiling hot
liquids into the
blender jar?
No, let the liquids or ingredients cool down to
80°C/175°F to avoid damage to the blender jar.
Why does the
motor produce
an unpleasant
smell during
processing?
It is very common for a new appliance to give off an
unpleasant smell or emit some smoke the rst few
times it is used. This phenomenon stops after you have
used the appliance a number of times. The appliance
may also give off an unpleasant smell or emit some
smoke if it has been used too long. In that case, switch
off the appliance and let it cool down for 60 minutes.
ENGLISH10
Question Answer
The appliance
stopped
running because
the blades are
blocked. What
should I do?
Switch off the appliance and unplug it. Then use a
spatula to dislodge the ingredients that block the
blades. If you were processing a large quantity, pour
some of the ingredients out of the blender jar before
you switch on the blender again.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
4203.064.5674.2www.philips.com/kitchen
/