Zibro Kamin R 59 C Owner's manual

Page is loading ...

Dear Sir, Madam,

Congratulations on your purchase of this Zibro Kamin heater, the number one

brand amongst portable heaters. You have purchased a quality product, which

will serve you for many years to come. This, of course, provided you use the

heater correctly. Please read these Directions for Use first, to ensure the

maximum lifetime for your heater.

This appliance comes with a 24-month manufacturer’s warranty on all defects

in materials or workmanship.

We wish you much warmth and comfort from your Zibro Kamin heater.

Yours sincerely,

PVG International b.v.

Customer Service Department

1 READ THE DIRECTIONS FOR USE FIRST.

2 IN CASE OF ANY DOUBT, CONTACT YOUR ZIBRO KAMIN DEALER.

3 BEFORE YOU START READING, FOLD OUT THE LAST PAGE.          

4

50

R 59 C

GENERAL DIRECTIONS FOR USE

Below you will find the main steps to be taken for

using your heater. For more details, please refer to

the MANUAL (pages 53 ff.).

• The first time you ignite your heater it will smell

like ’new’ for a short time.

• Store your fuel in a cool and dark place.

• Fuel has a limited shelf life. Start every heating

season with new fuel.

• The right quality of fuel will be assured, when

you use Zibro Plus for your heater.

• If you change to another brand and/or type of

parrafin oil, you must first finish up all the

remaining fuel in the heater.

MAIN COMPONENTS

Safety button (for

emergency stop)

Flame regulator

Igniter slide

Combustion chamber

handle

Fuel indicator

Grill

Lid for removable

tank

Removable tank

Fuel gauge

removable tank

Wick height lock

Ignition coil

Battery holder

Door





























                      

Remove all packaging materials (refer to Section A, Fig. A).

Fill the removable tank  and wait 30 minutes before you

ignite the heater

(refer to Section B, Fig. I).

Insert the batteries into the battery holder 

(refer to Section A, Fig. F).

Check whether the combustion chamber  is fully upright

(refer to Section A, Fig. E).

Ignite the heater by pushing down the flame regulator  and

the igniter slide

 simultaneously (refer to Section C, Fig. K).

Prior adjusting the flame (refer to Section D), let the heater

heat up for 10 to 15 minutes

.

Switch off the heater (refer to Section E).

1

2

3

4

5

6

7

4

51

R 59 C

WHAT YOU NEED TO KNOW IN ADVANCE

ALWAYS MAKE SURE THAT THERE IS SUFFICIENT VENTILATION

For each model the minimum size of space is specified in which you can use the

heater safely, without additional ventilation

(refer to Section K). If a particular

room is smaller than the specified space, always leave a window or door slightly

ajar (± 2.5 cm). We also recommend doing this in highly insulated or draught-free

rooms and/or at altitudes above 1,500 metres. However, if there is insufficient

ventilation (i.e. oxygen), the heater will automatically switch off. Do not use your

heater in cellars or other underground areas.

SAFE TOP

The heater is supplied with a safe top. This application decreases the temperature

of the top plate. In this way, the risk of harmful accidents at accidentally touching

the top plate is considerably decreased. However, be aware that the top plate still

becomes hot.

Avoid any contact with the top plate and grille.

THE RIGHT FUEL

Only use Class C1 paraffin fuel in accordance with BS2869 Part two, or equivalent.

Your Zibro Kamin heater has been designed for use with high-quality water-free

pure paraffin oil, such as Zibro Plus. Only fuels of this kind will ensure clean and

proper burning. Lower quality fuel may result in:

 excessive tar deposits on the glass fibre wick

 incomplete burning

 reduced heater lifetime

 smoke and/or smells

 deposits on the grid or mantle

Using the right fuel is therefore essential for safe, efficient, and comfortable use

of your heater.

Always refer to your local Zibro Kamin dealer for the right fuel for your heater.

4

52

R 59 C

A

The fuel cap cover can

be found at the rear of

the heater. This cover

allows you to keep your

hands clean when

opening the fuel tank.

This transportation cap

is packed separately in

the box. Only this cap

ensures trouble-free

transportation of the

heater after use.

Store it well!

Only the use of the

correct fuel will ensure

safe, efficient, and

comfortable use of your

heater.

MANUAL

A INSTALLING THE HEATER

Carefully remove your Zibro Kamin heater from the box and check the

contents. In addition to the heater you also need to have:

 the batteries

 a manual fuel pump

 a transportation cap

 a fuel cap cover

 these directions for use

Keep the box and the packaging materials (Fig. A) for storage and/or transportation.

Remove the other packaging materials:

 Remove the packaging material from the grill . Lift the grill from the slot

(Fig. B) and pull it forward.

 Push the packing material on top of the combustion chamber  slightly

down and remove it (Fig. C). Remove the packaging materials from under

the combustion chamber as well (Fig. D).

 Put the combustion chamber  back into its place. The combustion chamber

is positioned correctly when it can be smoothly moved a little to the left

and to the right by its handle

 (Fig. E). Close the grill: Slightly lift it to

reposition it in its slot.

 Open the lid of the removable tank  and remove the piece of cardboard.

Fill the removable tank as indicated in

Section B.

Insert the batteries into their holder  at the back of the heater (Fig. F).

Ensure that the positive and negative poles match the + and - marks indicated

on the battery housing.

The floor should be firm and completely level. Reposition the heater, when it is

not level. Do not correct the situation by placing books or goods under the

heater.

Please refer to the separate instruction in the carton box for fixing of

the heater.

Your Zibro Kamin heater is now ready for use.

B FILLING FUEL

Do not fill the removable tank in the living room, but in a more suitable place

(there can always be some spillage). Follow the procedure below:

Make sure that the heater is switched off.

Open the lid

 and lift the removable tank  out of the heater (Fig. G).

Note: Some drops may leak from the tank. Put down the removable tank

(cap pointing upwards) and screw off the fuel cap using the fuel cap cover (Fig. H).

2

1

6

5

4

3

2

1

4

53

R 59 C

     

B

C

D

E

F

H

G

Take the manual fuel pump and insert the smooth, most rigid tube into the

jerrycan. Make sure that it is in a higher position than the removable tank

(Fig. I). Insert the ribbed hose into the opening of the removable tank.

Lock the valve on top of the pump (turn clockwise).

Squeeze the pump a few times, until fuel starts flowing into the removable

tank. As soon as this happens, there is no need to press any longer.

Check the removable tank fuel gauge

 while filling the tank (Fig. J). Stop

filling by loosening the valve on top of the pump (turn anti-clock-wise), once

the gauge indicates that the tank is full. Never overfill the tank, especially not

when the fuel is very cold (fuel expands when it heats up).

Let the remaining fuel in the pump flow back into the jerrycan and carefully

remove the pump. Carefully screw the fuel cap back on the tank using the

fuel cap cover (Fig. H). Clean off any spilled fuel.

Check whether the fuel cap is straight and tightened properly. Reinstall the

removable tank in the heater (cap down). Close the lid.

C IGNITING THE HEATER

A new heater may give off some smells for a short while, when it is used for the

first time. You should therefore provide extra ventilation or ignite the heater

outside the living room.

When you use the heater for the first time, first put the filled removable tank into

place, and then wait approximately 30 minutes before you ignite the heater. This

allows the glass fibre wick to soak up the fuel. Follow the same procedure when you

have completely burnt up all fuel from the tank, and after the glass fibre wick has

been replaced.

Prior to igniting the heater, always check the fuel indicator

 for sufficient fuel in

the removable tank. Green = full, red = empty.

Always ignite the heater with the igniter slide. Never use matches or cigarette lighters.

Follow the procedure below:

Open the door

 at the front of the heater.

Slowly push down the igniter slide

 together with the flame regulator 

(Fig. K). At the same time you will activate the safety device.

Release the ignition slide as soon as a flame is visible at the bottom of the

combustion chamber

.

Close the door.

4

3

2

1

8

7

6

5

4

3

4

54

R 59 C

K

J

I

empty full

☞

After having ignited the heater, always check whether the combustion

chamber

 is level, by sliding it slightly to the left and the right by its handle

. This should be a smooth movement. If the combustion chamber is not level,

this will cause smoke and soot to develop.

D ADJUSTING THE FLAME

After you have ignited the heater, it will take 10 to 15 minutes for the flame to

become visible in the upper end of the combustion chamber. Only then can you

check whether the flame is correct. Too high a flame may cause smoke and soot,

whereas too low a flame causes smells. The page opposite the folding page shows

the minimum and maximum permissible burning heights of the flame (Fig. Q).

The flame can be adjusted continuously with the flame regulator

 (Fig. L).

If the flame remains low after the adjustment, the wick height must be

adjusted

(refer to Section F).

Too low a flame may also be caused by:

 insufficient fuel (fill the tank)

 poor fuel quality (contact your dealer)

 insufficient ventilation (leave window or door ajar)

 wastage of the wick (contact your dealer or replace the wick,

refer to section M)

E SWITCHING OFF THE HEATER

Let the heater burn at its lowest setting for approximately one minute. Then

slowly slide up the flame regulator

. The flame will extinguish by itself.

In cases of emergency: switch off the heater with the safety device

 (Fig. M).

F ADJUSTING THE WICK HEIGHT

After some time the flame may no longer be high enough (Section D). In that case

you can adjust the wick height to improve the flame. To do this, follow the next

procedure:

Open the door

 at the front of the heater.

Slide up the wick height lock

 one step to position 2 or 3 (Fig. N).

If this does not have the required effect, let the heater burn until all fuel is used

(Section H).

If the flame still remains too low after that and the wick is already set to

position 3, contact your Zibro Kamin dealer, or replace the wick

(Section M).

If the flame rises too high after the adjustment (Fig. Q), lower the wick height lock

setting one position. Otherwise there is a chance of smoke and soot production.

2

1

4

55

R 59 C

L

M

E

N

☞☞☞☞

G MALFUNCTION, CAUSES AND SOLUTIONS

If any malfunctioning cannot be solved from the directions below, please contact

your Zibro Kamin dealer.

THE HEATER DOES NOT IGNITE

 The batteries are not positioned correctly in the holder. Check (Fig. F).

 There is not enough power left in the batteries for the ignition. Replace (Fig. F).

 You have run out of fuel from the tank or the wick has been replaced.

After having refilled and replaced the removable tank, wait for 30 minutes

before igniting the heater.

 You are pushing down the igniter slide  with too much force.

Push it down less forcefully (Section C).

 The ignition coil  is defective.

Contact your dealer.

IRREGULAR FLAME AND/OR SOOT AND/OR SMELLS

 The combustion chamber  has not been positioned correctly.

Use the handle  to put it level, until you can easily slide it slightly to the left

and to the right and the chamber is level.

 The flame height has not been adjusted properly.

See Fig. Q and the directions in Section D.

 You are using fuel which is past its ‘use by’ date.

Start every heating season with fresh fuel.

 You are using the incorrect type of fuel.

Refer to THE RIGHT FUEL (Section ’What you need to know in advance’).

 Dust has gathered in the lower part of the heater.

Contact your dealer.

 The wick heigt has not been adjusted correctly

Refer to Section F.

THE HEATER SLOWLY EXTINGUISHES

 The removable tank is empty.

Refer to Section B.

 The fuel filter is contaminated by water.

Dry the fuel filter (Section H, Fig. O).

 The lower reservoir is contaminated by water.

Contact your dealer.

 The wick has hardened on the upper side.

Burn the heater until all fuel is used (Section H). Use the right fuel.

 You are using fuel which is past its ‘use by’ date.

Start every heating season with fresh fuel.

THE HEATER REMAINS BURNING LOW

 Wick position too low.

Move the wick height lock one position (Section F).

 Before you refilled the tank, the heater had burnt up almost all the fuel.

After having refilled and replaced the removable tank, wait for 30 minutes

before igniting the heater.

 You are using the incorrect type of fuel.

Refer to THE RIGHT FUEL (Section ’What you need to know in advance’).

 The room is insufficiently ventilated.

Leave a window or a door wide open for a while.

4

56

R 59 C

F

broken ignition coil

THE HEATER BURNS TOO HIGH, THE FLAMES CANNOT BE ADJUSTED.

 You are using an incorrect, too volatile type of fuel.

Refer to THE RIGHT FUEL (Section ’What you need to know in advance’).

 Wick position too high.

Move the wick height lock one position (Section F).

H MAINTENANCE

Your heater needs hardly any maintenance. It is, however, important that you

remove dust and stains in time with a damp cloth, because otherwise these may

cause stains that are hard to remove. Under normal conditions, only three

components are subject to wear:

1. THE BATTERIES

You may replace the batteries yourself. Do not dispose of old batteries along with

the other domestic waste. Follow the locally applicable regulations regarding the

disposal of domestic chemical waste.

2. THE WICK

To extend the glass fibre wick life, you must occasionally let the heater burn until

the tank is completely emptied and the heater extinguishes by itself. Do this when

you notice that the flame is weakening. The burn-out will cause some smells, so it

is recommended that you take the heater outside of the living room. If the flame

position isn’t high enough in position 3 of the wick height lock

, the wick needs

to be replaced.

Refer to section M or contact your Zibro Kamin dealer for

replacements.

3. THE IGNITION COIL

The ignition coil will last longer if you ignite in the right way. Replace the

batteries on time and make sure you do not push down the ignition slide too

forcefully. If the filament is broken, you should replace the coil.

THE FUEL FILTER

Check the fuel filter regularly as well.

Remove the removable tank

 from the heater and take out the fuel filter (Fig. O).

Some drops of fuel may spill from the filter; keep a cloth at hand. Turn the fuel

filter upside down and clean it from all dirt deposits by tapping it on a hard

surface.

(Never clean it with water!) Reposition the fuel filter in the heater.

Do not remove any heater components yourself. Always contact your Zibro

Kamin dealer for repairs.

Let the heater cool down first, before you start any maintenance or service work.

I STORAGE (END OF THE HEATING SEASON)

We recommend that you burn up all the fuel in the fuel tank at the end of the heating

season and store the heater properly. Follow the next procedure:

Ignite the heater outside the living room and let it burn until all fuel is used.

Let the heater cool down.

Clean the heater with a damp cloth and then dry it with a cloth.

3

2

1

4

57

R 59 C

☞☞

O

fuel filter

ignition coil

Remove the batteries from the holder  and store them in a dry place.

Clean the fuel filter

(refer to Section H).

Store the heater in a dust-free place, if possible in its original packaging.

Unused fuel cannot be used for the next heating season. If there is still some

fuel left, do not throw it away, but dispose of it in accordance with the local

regulations for the disposal of domestic chemical waste.

Always start the new heating season with fresh fuel. When you start re-using

the heater, follow the instructions again

(starting from Section A and as

specified).

J TRANSPORTATION

Take the following measures to avoid fuel leakage during the transportation of

the heater:

Let the heater cool down.

Remove the removable tank

 from the heater and remove the fuel filter

(Fig. O). Some drops may leak from the filter; keep a cloth at hand. Store the

fuel filter and the removable tank outside the heater.

Place the transportation cap into the position of the fuel filter (Fig. P).

Press it tight.

Always move the heater in an upright position.

K SPECIFICATIONS

Ignition electrical Dimensions (mm) width 428

Fuel paraffin (including base plate) depth 295

Capacity (kW)

*

2.7 height 513

Suitable space (m

3

)

**

45-95 Accessories: manual fuel pump

Fuel consumption (l/hr)

*

0.28 transportation cap

Fuel consumption (g/hr)

*

225 fuel cap cover

Burning time per tank (hr)

*

14 batteries

Capacity removable tank (litres) 4.0 Required batteries 2xLR 20, MN 1300,

Weight (kg) 9 alkaline 1.5V

Wick type F

* At maximum setting

** Specified values are indicative

L WARRANTY PROVISIONS

Your heater comes with a 24-month warranty starting on the date of purchase.

Within this period all defects in material or workmanship will be repaired without

any charge. The following provisions shall apply regarding this warranty:

4

3

2

1

7

6

5

4

58

R 59 C

P

transportation cap

O

fuel filter

We expressly dismiss all other claims for damages, including consequential

damages.

Any repairs or replacements of components within the term of warranty will

not result in an extension of the term of warranty.

The warranty shall no longer apply, when the heater has been modified,

non-original parts have been used, or when it is repaired by third parties.

The warranty shall not apply to parts that are subject to normal wear, such as

the batteries, the ignition coil, the wick and the manual fuel pump.

The warranty shall only apply, when you present the original, dated proof of

purchase, provided no changes have been made to it.

The warranty shall not apply to damages caused by actions not in compliance

with the Directions for Use, neglect, and the use of an incorrect type of fuel,

or fuel past its use-by date. The use of incorrect fuel can even be dangerous*.

Transportation costs and the risks involved during the transportation of the

heater or heater components shall always be for the account of the purchaser.

In order to avoid unnecessary costs, we recommend that you always read the

’Directions for Use’ carefully first. In case they offer no solution, please take the

heater to your dealer for repair.

* Highly inflammable substances may induce uncontrollable burning, causing flames to break out. Should this

happen, never try to move the heater, but always switch off the heater immediately

(refer to Section E). In cases

of emergency you may use a fire extinguisher, but only a type B extinguisher: a carbon dioxide or powder

extinguisher.

10 TIPS FOR SAFE USE

1 Make sure that children are always aware of the presence of a burning

heater.

2 Do not move the heater when it is burning or still hot. Do not refill nor

service the heater when it is burning or still hot.

3 Position the front of the heater at a minimum distance of 1.5 metres

from walls, curtains, and furniture.

4 Do not use the heater in dusty rooms or in very draughty places. In

both cases you will not have optimum burning.

5 Switch off the heater, before you go to sleep.

6 Store and move fuel only in suitable tanks and jerrycans.

7 Make sure that the fuel is not exposed to heat or extreme temperature

changes. Always store the fuel in a cool, dry and dark place (sunlight

will affect the quality).

8 Never use the heater in places where harmful gasses or fumes may be

present (e.g. exhaust gasses or paint fumes).

9 The top plate of the heater becomes hot. Do not cover the heater

(there is a risk of fire). Avoid any concact with the top plate and grille.

10 Always make sure that there is sufficient ventilation.

7

6

5

4

3

2

1

4

59

R 59 C

REPLACING THE WICK

M ENSURE THAT THE HEATER IS OFF AND COMPLETELY

COOLED BEFORE STARTING TO REPLACE THE WICK.

Open the lid and remove the removable tank.

Remove the batteries from the battery holder.

Check that both the igniter slide and the flame

regulator are in the uppermost position. Pull off the

plastic covers of the slides.

Open the front grill. Remove the combustion chamber

from the heater. Close the grill.

Unscrew the screws on the back and sides of the heater.

Pull the cabinet forward slightly and remove it from the

base plate. Unscrew the wing nuts from the wick holder

chassis.

Lift the wick holder chassis up until the wick is visible.

Place the burner bed next to the heater. (Ensure that

the wiring does not become disconnected).

Push the flame regulator down to adjust the wick

mechanism to its highest setting.

Turn the wick holder (with wick) to the left until it is

released and then remove it from the heater.

Remove the wick from the wick holder.

9

8

7

6

5

4

3

2

1

4

60

R 59 C

22

33

44bb

55aa

55cc

11

44aa

77

88

66

99

55bb

Place the new wick in the wick holder and press the

wick pins firmly into the holes in the wick holder.

Put the wick holder (with wick) back into position by

pushing the two large pins on the outside of the wick

holder into the rebate in the wick mechanism. Turn the

wick holder clockwise until it is firmly in place.

Put the wick holder chassis back into position.

Screw opposite wing nuts in succession until they are

hand tight.

Check that the wick mechanism works by pushing the

flame regulator all the way down and pushing on the

safety button.

Check that the tip-over-mechanism works by pushing

the flame regulator all the way down and tilting the

small piece of lead.

Put the cabinet back into position and tighten the

cabinet screws. Now put the combustion chamber back

into position. Check that it is level by sliding it slightly

to the left and the right by its handle. Close the grill.

Put the filled removable tank back into position.

Put the batteries into the battery holder (ensure that

the positive and negative poles match the + and –

marks indicated on the battery housing). Wait 30

minutes after placing the removable tank and batteries

before using the heater.

18

17

16

15

14

13

12

11

10

4

61

R 59 C

1100

1111aa

1111bb

1122

1144

1155

1166bb

1166cc

1177 1188

1133

1166aa

Page is loading ...

3 FRANCE

PVG France SARL

4, Rue Jean Sibélius

B.P. 185 - 76410

SOTTEVILLE SOUS LE VAL

tel: +33 2 32 96 07 47

fax: +33 2 32 96 07 77

email: [email protected]

i ÖSTERREICH

PVG Austria VertriebsgmbH

Salaberg 49

3350 HAAG

tel: +43 7434 44867

fax: +43 7434 44868

email: [email protected]

e BELGIË

PVG Belgium NV/SA

Industrielaan 55

2900 SCHOTEN

tel: +32 3 326 39 39

fax: +32 3 326 26 39

email: [email protected]

q SCHWEIZ

PVG Schweiz AG

Genuastrasse 15

4142 MÜNCHENSTEIN

tel: +41 61 337 26 51

fax: +41 61 337 26 78

email: [email protected]

2 DEUTSCHLAND

PVG Deutschland GmbH

Beiersdorfstraße 4

46446 EMMERICH

tel: +49 2821 76713

fax: +31 412 648385

email: [email protected]

6 DANMARK

PVG Scandinavia A/S

Niels Bohrsvej 10

6100 HADERSLEV

tel: +45 73 53 02 02

fax: +45 73 53 02 04

email: [email protected]

5 ESPAÑA

PVG España S.A.

Pol. Ind. San José de Valderas II

Comunidad ”La Alameda”

C / Aurora Boreal, 19

28918 LEGANÉS (Madrid)

tel: +34 91 611 31 13

fax: +34 91 612 73 04

email: [email protected]

4 UNITED KINGDOM

Lister Gases

Bridge Street

Holloway Bank, Wednesbury

West Midlands WS10 0AW

Tel.: +44 121 506 1818

Fax: +44 121 505 1744

email: gases@lister.co.uk

> ITALIA

PVG Italy SRL

Via Niccolò Copernico 5

50051 CASTELFIORENTINO (FI)

tel: +39 571 628500

fax: +39 571 628504

email: [email protected]

u NØRGE

Sunwind - Gylling A/S

Løxaveien 17 - P.O. Box 64

1351 RUD

tel: +47 67 17 13 70

fax: +47 67 17 13 80

email: [email protected]

1 NEDERLAND

PVG International b.v.

P.O.Box 96

5340 AB OSS

tel: +31 412 694694

fax: +31 412 622893

email: [email protected]

: POLSKA

PVG Polska Sp. z. o. o.

Kolonia Promna 58

26-803 PROMNA

tel: +48 48 615 16 33

fax: +48 48 615 16 33

email: [email protected]

9 PORTUGAL

Markt (Portugal), Lda

Recta da Granja do Marquês

ALGUEIRÃO

2725 MEM MARTINS

tel: + 351 21 922 8530

fax: + 351 21 922 8536

email: [email protected]

DISTRIBUTED IN EUROPE BY PVG INTERNATIONAL BV

New 3/03

Printed in Japan

7024000903

Zibro Kamin R 59 C, Kamin R 27 C, R 59C, R59C Owner's manual

Related papers

Other documents