Weider PRO 335 User manual

Brand: Weider

Model: PRO 335

Category: Fitness, gymnastics & weight training

Type: User manual

This manual is also suitable for

Model No. 831.150380

Serial No.

PATENT PENDING

The serial number can be found in the

location shown below. Write the serial

number in the space above.

CAUTION

Read all precautions and instruc-

tions in this manual before

using this equipment. Save this

manual for future reference.

USER'S MANUAL

Serial Number Decal (under seat)

SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179

TABLE OF CONTENTS

FULL 90 DAY WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

PART IDENTIFICATION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

ADJUSTING THE WEIDER PRO 335 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

FULL 90 DAY WARRANTY

For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this

SEARS WEIGHT BENCH EXERCISER, contact the nearest SEARS Service Center throughout the

United States and SEARS will repair or replace the WEIGHT BENCH EXERCISER, free of charge.

This warranty does not apply when the WEIGHT BENCH EXERCISER is used commercially or for rental

purposes.

This warranty gives you specific legal rights, and you may also have other rights which vary from state

to state.

SEARS, ROEBUCK AND CO., DEPT. 817WA, HOFFMAN ESTATES, IL 60179

IMPORTANT PRECAUTIONS

WARNING: To reduce the risk of serious injury, read the following important precautions before using

the weight bench.

1. Read all instructions in this manual before

using the weight bench.

2. Use the weight bench only as described in

this manual.

3. Use the weight bench only on a level surface.

Cover the floor beneath the weight bench for

protection.

4. Inspect and tighten all parts each time you

use the weight bench. Replace any worn

parts immediately.

5. Keep small children and pets away from the

weight bench at all times.

6. Always be sure there is an equal amount of

weight on each side of your barbell (not

included) when you are using it.

7. When you are using the weight carriage, be

sure there is an equal amount of weight on

each side of the weight tube.

8. Always wear athletic shoes for foot protec-

tion while exercising.

9. Keep hands and feet away from moving parts.

10. The weight bench does not include weights.

The weight bench is designed to support a

maximum of 510 pounds, including the user,

a weight bar and weights. Do not place more

than 310 pounds, including a weight bar and

weights, on the weight rests. Do not place

more than 150 pounds on the weight carriage;

use no more than 50 pounds for ab crunch-

es. Do not place more than 150 pounds on

the leg lever.

11. When using the backrest, make sure that the

adjustment tube is firmly seated in the

adjustment brackets on the uprights.

12. If you feel pain or dizziness at any time while

exercising, stop immediately and begin cool-

ing down.

13. It is the responsibility of the owner to ensure

that all users of the weight bench are ade-

quately informed of all precautions.

WARNING: Before beginning this or any exercise program, consult your physician. This is especially

important for persons over the age of 35 or persons with pre-existing health problems. Read all

instructions before using. SEARS assumes no responsibility for personal injury or property damage

sustained by or through the use of this product.

BEFORE YOU BEGIN

Backrest

Lock Pins

Weight Rests

Weight Carriage

Adjustment Tube

Adjustment

Brackets

Leg Lever

Seat

High Pulley

Station

Lat Bar

Weight Tube

Thank you for selecting the WEIDER

PRO 335

Weight Bench. The versatile PRO 335 Weight Bench is

designed to be used with your own weight set (not

included) to develop every major muscle group of the

body. Whether your goal is a shapely figure, dramatic

muscle size and strength, or a healthier cardiovascular

system, the PRO 335 Weight Bench will help you to

achieve the specific results you want.

For your benefit, read this manual carefully before

using the WEIDER

PRO 335 Weight Bench. If you

have additional questions, please call our toll-free

HELPLINE at 1-800-736-6879, Monday through

Saturday, 7 a.m. until 7 p.m. Central Time (excluding

holidays). To help us assist you, please note the prod-

uct model number and serial number before calling.

The model number is 831.150380. The serial number

can be found on a decal attached to the PRO 335

weight bench (see the front cover of this manual).

Before reading further, please review the drawing

below and familiarize yourself with the parts that are

labeled.

PART IDENTIFICATION CHART

This chart is provided to help you identify the small parts used in assembly. The number in parenthesis below

each part refers to the key number of the part. The second number refers to the quantity needed for assembly.

Important: Some parts may have been pre-assembled for shipping purposes. If you cannot find a part in

the parts bags, check to see if it has been pre-assembled.

M8 Nylon Locknut (7)–17

M8 Washer (2)–6

M10 Nylon Locknut (4)–6

M10 Washer (13)–4

3/4" Round Inner Cap (25)–6

1" Angled Round Cap (32)–1

M8 x 48mm Carriage Bolt (3)–6

M6 x 16mm Screw (6)–6

1" Round Inner Cap (21)–3

M8 x 50mm Bolt (1)–2

M8 x 68mm Bolt (8)–7

14mm x 15mm Spacer (11)–4

M10 x 70mm Bolt (12)–2

1 1/2" Round Inner Cap (14)–2

M10 x 75mm Bolt (5)–4

M10 x 63mm Bolt (19)–1

M4 x 25mm Screw (44)–1

1. Before beginning assembly, be sure that you

have read and understand the information in

the box above.

Set the Left and Right Base Sections (40, 47) on

the floor as shown. The indented holes must be

facing the floor. Insert two M8 x 48mm Carriage

Bolts (3) up through the indicated holes.

Press a 38mm x 50mm Inner Cap (16) into the

Lower Lat Tower (23). Slide the Lower Lat Tower

onto the two M8 x 48mm Carriage Bolts (3) in the

Base (40, 47). Insert two M8 x 68mm Bolts (8)

through the Lower Lat Tower and the Base.

Thread M8 Nylon Locknuts (7) onto all four Bolts.

Do not tighten the Nylon Locknuts yet.

2. Press two 38mm x 50mm Inner Caps (16) into the

Base (40). Insert four M8 x 48mm Carriage Bolts

(3) up through the Base.

ASSEMBLY

Before beginning assembly, carefully read the

following information and instructions:

• Place all parts of the WEIDER

PRO 335 in a

cleared area and remove the packing materials;

do not dispose of the packing materials until

assembly is completed.

• Read each assembly step before you begin.

• For help identifying the small parts used in

assembly, use the PART IDENTIFICATION

CHART on the previous page. Note: Some

small parts may have been pre-attached for ship-

ping purposes. If a part is not in the parts bag,

check to see if it has been pre-attached.

• Tighten all parts as you assemble them, unless

instructed to do otherwise.

• As you assemble the WEIDER

PRO 335, make

sure that all parts are oriented as shown in the

drawings.

THE FOLLOWING TOOLS (NOT INCLUDED) ARE

REQUIRED FOR ASSEMBLY:

• Two (2) adjustable wrenches

• One (1) standard screwdriver

• One (1) rubber mallet

• Lubricant, such as grease or petroleum jelly,

and soapy water will also be needed.

Assembly will be more convenient if you have the

following tools: A socket set, a set of open-end or

closed-end wrenches, or a set of ratchet wrenches.

The Indented Holes

must face the floor

3. Press two 2 1/2” Square Bushings (22) into the

Weight Carriage (15). Press two 1” Round Inner

Caps (21) into the Weight Carriage.

Press a 2 1/2” Square Bushing (22) into the

Carriage Stop (18). The hole in the Square

Bushing must be aligned with the indicated hole

in the Carriage Stop.

4. Slide the Weight Carriage (15) onto the Upper Lat

Tower (41). The Weight Carraige must be orient-

ed as shown.

Slide the Carriage Stop (18) onto the Upper Lat

Tower (41). The 2 1/2” Square Bushing (22) must

be facing toward the Weight Carriage (15). Attach

the Carriage Stop to the Upper Lat Tower with an

M8 x 68mm Bolt (8) and an M8 Nylon Locknut (7).

Insert the Upper Lat Tower (41) into the Lower Lat

Tower (23). Fully tighten the M10 x 56mm Bolt (19)

into the Lower Lat Tower.

Slide a Weight Stop (45) onto each side of the

Weight Carriage (15).

5. Wrap the Cable (10) around a Pulley (9). Attach the

Pulley to the Upper Lat Tower (41) with an M10 x

70mm Bolt (12), two M10 Washers (13), two 14mm x

15mm Spacers (11), and an M10 Nylon Locknut (4).

Attach the other Pulley (9) in the same manner.

Attach the other end of the Cable (10) to the eye-

bolt on the Weight Carriage (15).

Align these

Holes

6. Slide the Left Upright (42) onto the indicated M8 x

48mm Carriage Bolts (3). Hand-tighten an M8

Nylon Locknut (7) onto each Carriage Bolt. Be sure

that the Upright is turned as shown. Do not tighten

the Nylon Locknuts yet.

Attach the Right Upright (43) in the same manner.

Attach the Left Barbell Lock Pin (46) to the Left

Upright (42) with an M8 Nylon Locknut (7). Attach

the Right Barbell Lock Pin (17) to the Right Upright

(43) in the same manner. The Barbell Lock Pins

must be oriented as shown.

7. Attach the Cross Brace (30) to the Lower Lat Tower

(23) with two M8 x 50mm Bolts (1), two M8

Washers (2), and two M8 Nylon Locknuts (7).

Attach the Cross Brace (30) to the Left Upright (42)

with two M8 x 68mm Bolts (8), two M8 Washers (2),

and two M8 Nylon Locknuts (7).

Attach the Cross Brace (30) to the Right Upright

(43) with two M8 x 68mm Bolts (8), two M8

Washers (2), and two M8 Nylon Locknuts (7).

Tighten all M8 Nylon Locknuts (7) used in steps

1, 6, and 7.

8. Press a 1 1/2” Round Inner Cap (14) into each end

of the Adjustment Tube (37).

Set the Adjustment Tube (37) into one set of adjust-

ment brackets on the Left and Right Uprights (42,

43).

Adjustment

Brackets

9. Lubricate an M10 x 75mm Bolt (5). Attach the

Bench Frame (33) to the Cross Brace (30) with the

M10 x 75mm Bolt and an M10 Nylon Locknut (4).

The Bench Frame must be turned as shown. Do

not overtighten the Nylon Locknut.

Attach the Bumper (24) to the Bench Frame (33)

with an M4 x 25mm Screw (44).

Press a 38mm x 50mm Inner Cap (16) into the

Bench Frame (33).

10. Press a 38mm x 50mm Inner Cap (16) into each

end of the Front Leg (20).

Lubricate an M10 x 75mm Bolt (5). Attach the Front

Leg (20) to the Bench Frame (33) with the M10 x

75mm Bolt (5) and an M10 Nylon Locknut (4). Do

not overtighten the Nylon Locknut.

11. Press two 38mm x 50mm Inner Caps (16) into the

Leg Lever (28). Press a 1” Round Inner Cap (21)

into the Front Leg. Press an Angled Round Cap

(32) onto the Leg Lever.

Lubricate an M10 x 75mm Bolt (5). Attach the Leg

Lever (28) to the Front Leg (20) with the M10 x

75mm Bolt (5) and an M10 Nylon Locknut (4). Do

not overtighten the Nylon Locknut.

Slide a Weight Stop (45) onto the Leg Lever (28).

12. Attach both Backrest Brackets (38) to the Backrest

(36) with four M6 x 16mm Screws (6). The

Backrests must be oriented as shown.

Lubricate

13. Lubricate an M10 x 75mm Bolt (5). Attach the

Backrest Brackets (38) to the Bench Frame (33)

with the M10 x 75mm Bolt and an M10 Nylon

Locknut (4). Do not overtighten the Nylon

Locknut.

Rest the Backrest Brackets (38) on the Adjustment

Tube (37).

14. Attach the Seat (35) to the Bench Frame (33) with

two M6 x 16mm Screws (6).

15. Press 3/4” Round Inner Caps (25) into the ends of

all three Pad Tubes (27).

Insert a Pad Tube (27) through the indicated hole in

the Leg Lever (28). Insert another Pad Tube through

the other hole in the Leg Lever. Insert the remaining

Pad Tube through the hole in the Front Leg (20).

Slide two Foam Pads (26) onto each Pad Tube (27).

Lubricate

16. Wet the ends of the Lat Bar (31) with soapy water.

Slide a Handgrip (39) onto each end of the Lat Bar.

CAUTION: Allow the Handgrips (39) to dry

thoroughly before using the Lat Bar (31).

17. Be sure that all parts have been tightened properly. The use of all remaining parts will be explained in

ADJUSTING THE WEIDER PRO 335 beginning on page 12 of this manual.

ADJUSTING THE WEIDER PRO 335

The weight bench is designed to be used with your own weight set (not included). The steps below explain how

the weight bench can be adjusted. See EXERCISE GUIDELINES on page 14 for important exercise information

and refer to the accompanying exercise poster to see the correct form for each exercise. Refer also to the exer-

cise information accompanying your weight set for additional exercises.

Inspect and tighten all parts each time you use the weight bench. Replace any worn parts immediately. The

weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.

ATTACHING WEIGHTS TO THE WEIGHT CARRIAGE

To use the lat tower, first slide a Weight Stop (45) onto

each side of the weight tube of the Weight Carriage (15).

Slide the desired amount of weight (not included) onto the

weight tube. Be sure that an equal amount of weight is on

each side of the weight tube. Secure the weights on each

side of the weight tube with a Spring Clip (29).

Do not place more than 150 pounds on the Weight

Carriage. (Due to the fact that ab crunches are an aer-

obic exercise, we recommend that you do not place

more than 50 pounds on the Weight Carriage (15) while

performing ab crunch exercises.)

ATTACHING WEIGHTS TO THE LEG LEVER

To use the Leg Lever (28), be sure there is a Weight Stop

(45) on the weight tube. Then slide the desired amount of

weight (not included) onto the weight tube.

Do not place more than 150 pounds on the Leg Lever.

ADJUSTING THE BACKREST

The Backrest (36) can be set at three different positions:

the level position, the decline position, and the incline posi-

tion.

To change the position of the Backrest (36) to either the

incline position or the level position, move the Adjustment

Tube (37) to a different set of adjustment brackets on the

Left and Right Uprights (42, 43). Set the Backrest (36)

onto the Adjustment Tube.

To change the position of the Backrest (36) to the decline

position, remove the Adjustment Tube (37). Set the

Backrest (36) onto the Bench Frame (33).

Weight

Tube

Adjustment

Brackets

Weight

Tube

ATTACHING THE LAT BAR TO THE HIGH PULLEY

STATION

Attach the Lat Bar (31) to the Cable (10) with a Cable

Clip (34).

WARNING: Always sit on the backrest when using

the high pulley station. The backrest must be in the

level position (see ADJUSTING THE BACKREST on

page 12).

LOCKING THE BARBELL

To change weights while your barbell (not included) is

on the Uprights (42, 43), secure your barbell with the

Barbell Lock Pins (17, 46). This will reduce the possibili-

ty of the barbell tipping while you change weights.

Place the same amount of weight on both ends of

the barbell.

STORING THE WEIGHT BENCH

The WEIDER PRO 335 weight bench is designed to be

folded into a compact storage position when it is not in

use.

First remove the Adjustment Tube (37). Lay the

Backrest (36) on the Bench Frame (33).

Fold the Bench Frame (33) up, as shown in the inset

drawing. Fold down the Front Leg (20). Set the

Adjustment Tube (37) into the upper adjustment brack-

ets to hold the Bench Frame in place.

Barbell

EXERCISE GUIDELINES

THE FOUR BASIC TYPES OF WORKOUTS

• Muscle Building

In order to increase the size and strength of your mus-

cles, you must push your muscles to a high percent-

age of their capacity. You must also progressively

increase the intensity of your exercise so that your

muscles will continually adapt and grow. Each individ-

ual exercise can be tailored to the proper intensity

level by changing the amount of weight used, or the

number of repetitions or sets performed. (A “repetition”

is one complete cycle of an exercise, such as one sit-

up. A “set” is a series of repetitions performed consec-

utively.)

The proper amount of weight for each exercise

depends upon the individual user. It is up to you to

gauge your limits. Select the amount of weight that you

think is right for you. Begin with 3 sets of 8 repetitions

for each exercise that you perform. Rest for 3 minutes

after each set. When you can complete 3 sets of 12

repetitions without difficulty, increase the amount of

weight.

• Toning

To tone your muscles, you must push your muscles to

a moderate percentage of their capacity. Select a mod-

erate amount of weight and increase the number of

repetitions in each set. Complete as many sets of 15

to 20 repetitions as possible without discomfort. Rest

for 1 minute after each set. Work your muscles by

completing more sets rather than by using high

amounts of weight.

• Weight Loss

To lose weight, use a low amount of weight and

increase the number of repetitions in each set.

Exercise for 20 to 30 minutes, resting for a maximum

of 30 seconds between sets.

• Cross Training

In the pursuit of a complete and well-balanced fitness

program, many have found that cross training is the

answer. We recommend that on Monday, Wednesday

and Friday, you plan weight training workouts. On

Tuesday and Thursday, plan 20 to 30 minutes of aero-

bic exercise, such as cycling, running or swimming.

Rest from both weight training and aerobic exercise for

at least one full day each week to give your body time

to regenerate. By combining weight training with aero-

bic exercise, you can reshape and strengthen your

body, plus develop a stronger heart and lungs.

PERSONALIZING YOUR EXERCISE PROGRAM

We have not specified an exact length of time for each

workout, or a specific number of repetitions or sets for

each exercise. It is very important to avoid overdoing it

during the first few months of your exercise program,

and to progress at your own pace. If you experience

pain or dizziness at any time while exercising, stop

immediately and begin to cool down. Find out what is

wrong before continuing. Remember that adequate

rest and a proper diet are also important.

WARMING UP

Begin each workout with 5 to 10 minutes of light

stretching and exercise to warm up. Warming up pre-

pares your body for exercise by increasing circulation,

raising your body temperature and delivering more

oxygen to your muscles.

WORKING OUT

Each workout should include 6 to 10 different exercis-

es. Select exercises for every major muscle group, with

emphasis on the areas that you want to develop the

most. To give balance and variety to your workouts,

vary the exercises from workout to workout.

Schedule your workouts for the time of day when your

energy level is the highest. Each workout should be

followed by at least one day of rest. Once you find the

schedule that is right for you, stick with it.

EXERCISE FORM

In order to obtain the greatest benefits from exercising,

it is essential to maintain proper form.

Maintaining proper form means moving through the full

range of motion for each exercise, and moving only the

appropriate parts of the body. Exercising in an uncon-

trolled manner will leave you feeling exhausted. On the

exercise poster accompanying this manual, you will

find photographs showing the correct form for several

exercises. A description of each exercise is also pro-

vided, along with a list of the muscles affected. Refer

to the muscle chart on page 16 to find the locations of

the muscles.

The repetitions in each set should be performed

smoothly and without pausing. The exertion stage of

each repetition should last about half as long as the

return stage. Proper breathing is important. Exhale

during the exertion stage of each repetition and inhale

during the return stroke; never hold your breath. Rest

for 3 minutes after each set if you are doing a muscle

building workout, 1 minute after each set if you are

doing a toning workout, and 30 seconds after each set

if you are doing a weight loss workout. Plan to spend

the first couple of weeks familiarizing yourself with the

equipment and learning the proper form for each exer-

cise.

COOLING DOWN

End each workout with 5 to 10 minutes of stretching.

Include stretches for both your arms and legs. Move

slowly as you stretch—do not bounce. Ease into each

stretch gradually and go only as far as you can without

strain. Stretching at the end of each workout is very

effective for increasing flexibility.

STAYING MOTIVATED

For motivation, keep a record of each workout. The

chart on page 17 of this manual can be photocopied

and used to schedule and record your workouts. List

the date, exercises performed, weight, and numbers of

sets and repetitions completed. Record your weight

and key body measurements at the end of every

month.

Remember, the key to achieving the greatest results is

to make exercise a regular and enjoyable part of your

everyday life.

MUSCLE CHART

A. Sternomastoid (neck)

B. Pectoralis Major (chest)

C. Biceps (front of arm)

D. Obliques (waist)

E. Brachioradials (forearm)

F. Hip Flexors (upper thigh)

G. Abductor (outer thigh)

H. Quadriceps (front of thigh)

I. Sartorius (front of thigh)

J. Tibialis Anterior (front of calf)

K. Soleus (front of calf)

L. Rectus Abdominus (stomach)

M. Adductor (inner thigh)

N. Trapezius (upper back)

O. Rhomboideus (upper back)

P. Deltoid (shoulder)

Q. Triceps (back of arm)

R. Latissimus Dorsi (mid back)

S. Spinae Erectors (lower back)

T. Gluteus Medius (hip)

U. Gluteus Maximus (buttocks)

V. Hamstring (back of leg)

W. Gastrocnemius (back of calf)

MONDAY

Date:

/ /

EXERCISE WEIGHT SETS REPS

AEROBIC EXERCISE

TUESDAY

Date:

/ /

WEDNESDAY

Date:

/ /

THURSDAY

Date:

/ /

FRIDAY

Date:

/ /

Make photocopies of this page for scheduling and recording your workouts.

PART LIST—Model No. 831.150380 R0996A

Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover

of this manual for information about ordering replacement parts.

Key Part

No. Qty. No. Description

1 2 013105 M8 x 50mm Bolt

2 6 014012 M8 Washer

3 6 013001 M8 x 48mm Carriage Bolt

4 6 012033 M10 Nylon Locknut

5 4 132138 M10 x 75mm Bolt

6 6 132137 M6 x 16mm Screw

7 17 012002 M8 Nylon Locknut

8 7 013047 M8 x 68mm Bolt

9 2 115370 Pulley

10 1 132140 Cable

11 4 128051 14mm x 15mm Spacer

12 2 110942 M10 x 70mm Bolt

13 4 014015 M10 Washer

14 2 115998 1 1/2” Round Inner Cap

15 1 132143 Weight Carriage

16 8 132142 38mm x 50mm Inner Cap

17 1 132144 Right Barbell Lock Pin

18 1 132145 Carriage Stop

19 1 111083 M10 x 56mm Bolt

20 1 132146 Front Leg

21 3 120733 1” Round Inner Cap

22 3 127941 2 1/2” Square Bushing

23 1 132147 Lower Lat Tower

24 1 122950 Bumper

25 6 112402 3/4” Round Inner Cap

Key Part

No. Qty. No. Description

26 6 103805 Foam Pad

27 3 132148 Pad Tube

28 1 132149 Leg Lever

29 2 130312 Spring Clip

30 1 132187 Cross Brace

31 1 132150 Lat Bar

32 1 123396 1” Angled Round Cap

33 1 132151 Bench Frame

34 1 103087 Cable Clip

35 1 132188 Seat

36 1 132189 Backrest

37 1 132152 Adjustment Tube

38 2 132182 Backrest Bracket

39 2 112560 Handgrip

40 1 132183 Right Base Section

41 1 132184 Upper Lat Tower

42 1 132185 Left Upright

43 1 132186 Right Upright

44 1 132139 M4 x 25mm Screw

45 3 123403 Weight Stop

46 1 133123 Left Barbell Lock Pin

47 1 133142 Left Base Section

# 1 132002 User’s Manual

# 1 129186 Exercise Poster

EXPLODED DRAWING—Model No. 831.150380 R0996A

Model No. 831.150380

QUESTIONS?

If you find that:

• you need help assembling or

operating the WEIDER

PRO 335

• a part is missing

• or you need to schedule repair

service

call our toll-free HELPLINE

1-800-736-6879

Monday–Saturday, 7 am–7 pm

Central Time (excluding holidays)

REPLACEMENT PARTS

If parts become worn and need to

be replaced, call the following toll-

free number

1-800-FON-PART

(1-800-366-7278)

The model number and serial number of your WEIDER

PRO 335

are listed on a decal attached to the frame. See the front cover of

this manual to find the location of the decal.

All replacement parts are available for immediate purchase or

special order when you visit your nearest SEARS Service Center.

To request service or to order parts by telephone, call the toll-free

numbers listed at the left.

When requesting help or service, or ordering parts, please be pre-

pared to provide the following information:

• The MODEL NUMBER of the product (831.150380).

• The NAME of the product (WEIDER

PRO 335 Weight Bench).

• The PART NUMBER of the PART (see the PART LIST and the

EXPLODED DRAWING on pages 18 and 19 of this manual).

• The DESCRIPTION of the PART (see the PART LIST and the

EXPLODED DRAWING on pages 18 and 19 of this manual).

SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179

Weider PRO 335 User manual

Brand: Weider

Model: PRO 335

Category: Fitness, gymnastics & weight training

Type: User manual

This manual is also suitable for

Download PDF

report

Weider PRO 335 User manual

This manual is also suitable for

Weider PRO 335 User manual

Related papers

Other documents