Uniden TXC580 User manual

Inter-Tel

INT1100

User Guide

INT1100 Manual-5.0.qxd 1/29/04 12:09 AM Page i Bob's Garage: New Backup: Clients:CoastlineCreative:Clients:Inte

Contents

Welcome/Features 3

Quick Reference Guide 4

Controls and Functions 5

Getting Started 7

Read this First 7

Setting up the Phone 8

Terminology 12

Setting Caller ID Options 13

Selecting a Language 15

Basics 16

Making and Receiving Calls 16

Redialing a Call 17

Ringer Volume Setup 18

Ringer Tone Setting 18

Distinctive Ringer Setup 19

Adjusting the Earpiece and Handset Speaker Volume 20

Mute Microphone 20

Tone Dialing Switch-over 21

Traveling Out-of-Range 21

Selecting a Different Channel 21

Find Handset 22

Flash and Call Waiting 22

Voice Mail LED 22

Phonebook 23

Storing Phone Numbers, Names,

Distinctive Rings, and Speed Dial 23

Steps for Entering Names and Special Characters 25

Viewing the Phonebook 27

Making Calls Using the Phonebook 28

Speed Dialing 28

Editing or Erasing a Stored Name,

Phone Number, Distinctive Ring, and Speed Dial 29

RocketDial (One Touch Dialing) 30

Chain Dialing 31

Caller ID 32

Viewing the Caller ID List 33

Deleting Information from the Caller ID List 34

Using the Caller ID Message List 35

Call Waiting Deluxe Features 36

Additional Information 37

Changing the Digital Security Code 37

Installing the Beltclip 38

Headset Installation 38

Note on Power Sources 39

Maintenance 39

General Information 40

Troubleshooting 41

Liquid Damage 42

Precautions & Warranty 43

Index 45

[ 2 ]

INT1100 Manual-5.0.qxd 1/29/04 12:09 AM Page 2 Bob's Garage: New Backup: Clients:CoastlineCreative:Clients:Inte

Welcome

Features

Congratulations on your purchase of the Inter-Tel® cordless telephone. This phone is designed

and engineered to exacting standards for reliability, long life and outstanding performance. To

enjoy the best performance from this phone’s features, please read this manual carefully and

save it for future reference.

Note: Some illustrations in this manual may differ from the actual unit for explanation

purposes.

As an Energy Star® Partner, Inter-Tel has determined that this product or product

models meets the Energy Star® guidelines for energy efficiency.

Energy Star® is a U.S. registered mark.

Note: Energy Star® applies to INT1100 only.

• 5.8 GHz Spread Spectrum Technology

• Hands Free Speakerphone in the Handset

• Caller ID and Call Waiting Caller ID

• Dynamic Memory Location for Caller ID Messages and

Phonebook Locations (up to 100 numbers in total)

• Trilingual Language Option

• 3-Line, 16 Character Backlit Handset Display

• One Touch Rocket Dialing

• Call Transfer

• 32 Digit Redial / 3 Last Number Redial Locations (handset only)

• 10 Distinctive Ring Options (6 ringers and 4 melodies)

• Mute Feature

• Flash and Pause

• Find Handset

• Hearing Aid Compatible

• Tone/Pulse Dialing

• Handset Earpiece, Handset Speaker, and Ringer Volume Control

• Call Timer

WELCOME/FEATURES [ 3 ]

INT1100 Manual-5.0.qxd 1/29/04 12:09 AM Page 3 Bob's Garage: New Backup: Clients:CoastlineCreative:Clients:Inte

QUICK REFERENCE GUIDE

Q

UICK

R

EFERENCE

G

UIDE

INSTALL THE HANDSET BATTERY

Remove the cover.

Connect the battery

pack connector with

the correct polarity.

Replace the cover.

PLUG INTO AC POWER

Plug the AC adapter cord into the base unit and

then to a 120V AC outlet.

Place the handset in the base.

Note:

You must charge the battery pack continuously

for 15-20 hours before using the phone.

Step 1 Charging the Battery Step 2 Connecting

Step 3 Setting up the Caller

ID Options/Language

CONNECT TO A PHONE LINE

When the handset battery pack is fully charged, plug

the telephone cord into the base unit and then into a

telephone wall jack.

Your phone is set for tone dialing. If your local network

requires pulse dialing, please see “Setting up the phone,

Choose the dialing mode” in your owner’s manual.

Note: Three Caller ID options are

available: Auto Talk, Caller ID on Call

Waiting (CIDCW) and Area Code.

[ 4 ]

TO SELECT CALLER ID OPTIONS

Press menu/mute.

Press + or - to move the pointer to

“Caller ID Setup”,

then press select/ch.

Press

+

or

-

to move the pointer to an option,

then press

select/ch

.

Press

+

or

-

to change the option setting.

Press

select/ch and return the handset to

the base.

TO CHOOSE THE LANGUAGE

Press menu/mute.

Press + or - to move the pointer to “Language”,

then press select/ch.

Press + or - to change the option setting.

Press select/ch and return the handset to

the base.

INT1100 Manual-5.0.qxd 1/29/04 12:09 AM Page 4 Bob's Garage: New Backup: Clients:CoastlineCreative:Clients:Inte

[ 5 ]

Controls and Functions

CONTROLS AND FUNCTIONS

2

1

3

4

5

6

7

8

9

10

11

12

14

13

22

15

16

17

18

20

19

21

23

1. Handset Antenna

2. Headset Jack Cover

3. Beltclip Hole

4. Handset Battery Compartment

5. Voice Mail LED

6. Handset Earpiece

7. LCD Display

8. call id (Caller ID)/

 (right cursor) Key

9. (Phonebook)/RocketDial/

 (left cursor) Key

10. spkr (speaker) Key

11. /tone Key

12. redial/p (pause) Key

13. Menu/ (mute) Key

14. Handset Microphone

15. Talk/flash Key

16.

+ (up) Key

17.

- (down) Key

18. End Key

19.

# Key

20. Xfer (transfer)/ del (delete) Key

21. Select/ch (channel) Key

22. Handset Charging Contacts

23. Hands Free Speaker

INT1100 Manual-5.0.qxd 1/29/04 12:09 AM Page 5 Bob's Garage: New Backup: Clients:CoastlineCreative:Clients:Inte

[ 6 ] CONTROLS AND FUNCTIONS

24

26

25

28 29

27

24. Base Antenna

25. Base Charging Contacts

26. Status LED

27. Find Handset Key

28. DC Power Input

29. Telephone Line Jack

INT1100 Manual-5.0.qxd 1/29/04 12:09 AM Page 6 Bob's Garage: New Backup: Clients:CoastlineCreative:Clients:Inte

[ 7 ]GETTING STARTED

Read this First

This cordless telephone must be set up before use. Follow these steps:

About the digital security code

This cordless telephone uses a digital

security code to prevent unauthorized

access to your base unit. This security

code prevents other cordless handsets

from making calls through your base unit.

If you want to change the security code,

see page 43.

Step 1 (page 9)

Unpack the telephone and accessories.

Step 2 (page 10)

Next, choose the best location to set up the

base unit.

Step 3 (page 11 to 14)

Then, insert the battery pack into the handset.

Connect the base unit. You must charge the battery

pack

for 15-20 hours before plugging into the

phone line and using the phone.

Step 4 (page 15 to 17)

Finally, set the Caller ID options, and store your area

code in the memory to use the Caller ID service. Choose

the language of your display.

Note: Skip the area code setting if your calling area

requires 10-digit dialing.

INT1100 Manual-5.0.qxd 1/29/04 12:09 AM Page 7 Bob's Garage: New Backup: Clients:CoastlineCreative:Clients:Inte

[ 8 ] GETTING STARTED

Setting up the Phone

Do the following steps:

A. Choose the best location C. Connect the base unit

B. Install the battery pack D. Choose the dialing mode

A. Choose the best location

Before choosing a location for your new phone, read “Installation Considerations” on

page 44. Here are some important guidelines you should consider:

Avoid excessive

moisture, extremely

low temperatures, dust,

mechanical vibration,

or shock

Avoid heat sources, such as

radiators, air ducts, and sunlight

Avoid television sets and

other electronic equipment

Avoid noise sources such as a window

by a street with heavy traffic

Avoid microwave ovens

Avoid personal computers

Avoid other cordless telephones

Choose a central location

For maximum range:

• Keep the antenna free of

obstruction.

• When the handset is not

in use place the handset

in an upright position.

• Do not hold the handset

where you would block

the signal.

Correct

Incorrect

If your home has specially wired alarm equipment connected to the telephone line,

be sure that installing the system does not disable your alarm equipment.

If you have questions about what will disable your alarm equipment, contact your

telephone company or a qualified installer.

INT1100 Manual-5.0.qxd 1/29/04 12:09 AM Page 8 Bob's Garage: New Backup: Clients:CoastlineCreative:Clients:Inte

[ 9 ]

GETTING STARTED

B. Install the battery pack

Charge the battery pack for at least 15-20 hours before

plugging the phone line into your base unit.

1) Press down on the battery cover release and slide the cover

down until it comes off.

2) Connect the battery pack connector observing the correct

polarity (black and red wires) to the jack inside the battery

compartment.

Do not exert any force on this connection. It could cause

damage to the battery or to the handset. The plastic

connectors will fit together in only one way. Once you are

certain that you have made a good connection, then insert

the battery pack into the battery compartment.

Do not pinch the wires.

3) Securely close the battery compartment cover by sliding it

up until it snaps into place.

4) Place the handset in the base with the keypad facing

forward.

• Use only the Inter-Tel

battery (BT-446)

supplied with your

phone.

Replacement

batteries are also

available through

Inside Sales.

• Recharge your phone on

a regular basis by

returning the handset to

the base after each

phone call.

INT1100 Manual-5.0.qxd 1/29/04 12:09 AM Page 9 Bob's Garage: New Backup: Clients:CoastlineCreative:Clients:Inte

[ 10 ] GETTING STARTED

Battery use time (per charge)

Fully charged (15-20 hours charge time)

• Up to 4 hours continuous use

• Up to 8 days when the handset is in the standby mode

Cleaning the battery charging contacts

To maintain a good charge, it is important to clean the

charging contacts on both the handset and base unit

once a month. Use a dry cloth or pencil eraser to

clean. If the contacts become very dirty, using water

only, dampen a cloth to clean the charging contacts.

Then make sure to go back over the charging contacts

with a dry cloth before returning the handset to the

base to charge.

contacts

When you charge the handset, Caller ID summary screen and the name

of the handset,

HS1 appears. For TRU5860-2, if HS2 appears, you are

charging the handset No. 2.

The last number dialed in the redial memory is retained for up to

2 minutes while you replace the battery pack.

Low battery alert

When the battery pack is very low and needs to be charged, the

phone is programmed to eliminate functions in order to save power.

If the phone is in the standby mode, ”

Low Battery” appears on

the LCD and none of the keys will operate. If the phone is in use,

”

Low Battery” appears and the handset beeps. Complete your

conversation as quickly as possible and return the handset to the

base unit for charging.

INT1100 Manual-5.0.qxd 1/29/04 12:09 AM Page 10 Bob's Garage: New Backup: Clients:CoastlineCreative:Clients:Int

[ 11 ]

GETTING STARTED

• Use only the supplied AD-312 AC adapter.

Do not use any other AC adapter.

• Connect the AC adapter to a continuous power supply.

• Place the base unit close to the AC outlet so that you can unplug

the AC adapter easily.

C. Connect the base unit

1) Connect the AC adapter to the DC IN 9V

jack and to a standard 120V AC wall

outlet.

2) Set the base and charger (for TRU5860-2

only) on a desk or tabletop, and place the

handset in the base unit as shown.

3) Make sure the

status LED illuminates. If the LED does not

illuminate, check to see that the AC adapter is plugged in

and that the handset makes good contact with the base

charging contacts.

Place the power cord so

that it does not create

a trip hazard or where it

could become chafed

and create a fire or

electrical hazard.

4) After installing the battery pack in the handset,

charge your handset at least

15-20 hours before

plugging into the phone line.

5) Once the handset battery pack is fully charged,

connect the telephone line cord to the

TEL LINE

jack and to a telephone outlet.

If your telephone outlet isn't modular

type, contact your telephone company

for assistance.

Modular

INT1100 Manual-5.0.qxd 1/29/04 12:09 AM Page 11 Bob's Garage: New Backup: Clients:CoastlineCreative:Clients:Int

[ 12 ] GETTING STARTED

D. Choose the dialing mode

Most phone systems use tone dialing, which sends DTMF tones through the phone lines.

However some phone systems still use pulse dialing such as in rural areas. The default setting

is tone dialing. Depending on your dialing system, set the mode as follows:

1) When the phone is in the standby mode, press

menu/mute.

2) Press

+ or - to move the pointer to “Dial Mode”.

3) Press select/ch and the display will show the current setting. (The

initial setting is Tone.)

4) Press

+ or - to change the selection.

5) Press

select/ch, and you will hear a confirmation tone.

6) Press

end to exit.

Throughout this manual, terms such as Standby and Talk Mode are used. Below is the terminology

explanation.

Standby Mode - The handset is not in use, is off the base, and talk/flash or spkr has not been

pressed. A dial tone is not present.

Talk Mode - The handset is not in the base and talk/flash or spkr has been pressed enabling a

dial tone. “

Talk” appears in the display.

Terminology

• If you are not sure of

your dialing system, set

the unit to tone dialing.

Make a trial call. If the

call connects, leave the

setting as is, otherwise

set the unit to pulse

dialing.

• If your phone system

requires pulse dialing

and you need to send

DTMF tones in certain

situations during a call,

you may “switch-over”

to tone dialing. (Refer

to “Tone Dialing Switch-

over” on page 21.)

INT1100 Manual-5.0.qxd 1/29/04 12:09 AM Page 12 Bob's Garage: New Backup: Clients:CoastlineCreative:Clients:Int

[ 13 ]

GETTING STARTED

To change your Caller ID options:

1) When the phone is in the standby mode, press

menu/mute.

2) Press

+ or - to move the pointer to “Caller ID Setup”, then

press

select/ch.

3) Press

+ or - to choose “Auto Talk” or “CIDCW”,

then press

select/ch.

4) Press

+ or - to change the selection.

AutoTalk: “

Auto Talk On” or “Auto Talk Off”

CIDCW: “

CIDCW On”, “CW Deluxe On” or “CIDCW Off”

5) Press

select/ch and you will hear a confirmation tone.

6) Press

end to exit.

Setting Caller ID Options

There are three Caller ID setup options available: AutoTalk, CIDCW (Caller ID on Call Waiting),

and Area Code. See page 14 for Area Code setup instructions.

AutoTalk allows you to answer the phone without pressing

talk/flash or spkr. If the phone rings

when AutoTalk is On, simply remove the handset from the base and the phone automatically

answers the call. Or if the handset is not in the base, press any number key,

/tone, or # to

answer the call. If you set AutoTalk to Off, you must press

talk/flash or spkr to answer the call.

Caller ID on Call Waiting (CIDCW) performs the same as regular Caller ID on a call waiting

number. CW Deluxe allows you to handle call waiting calls in seven different ways. (See page 36.)

You must subscribe to CIDCW from your phone company in order to use this feature.

The CW Deluxe is a separate service available through your phone company.

INT1100 Manual-5.0.qxd 1/29/04 12:09 AM Page 13 Bob's Garage: New Backup: Clients:CoastlineCreative:Clients:Int

[ 14 ] GETTING STARTED

Entering Your Area Code

If you enter a 3-digit area code number in the “Area Code” option, your local area code does

not appear in Caller ID messages. For calls received from outside your local area code, you will

see a full 10-digit number.

1) When the phone is in the standby mode, press

menu/mute.

2) Press

+ or - to move the pointer to “Caller ID Setup”,

then press

select/ch.

3) Press

+ or - to move the pointer to “Area Code”,

then press

select/ch.

4) Use the number keypad (0 to 9) to enter a 3-digit

area code.

5) Press

select/ch, and you will hear a confirmation tone.

6) Press

end to exit.

• If your calling area

requires 10-digit

dialing, do not program

this option.

• When the area code has

already been stored in

memory, the stored area

code will be displayed.

To change it, press

xfer/del three times.

Then enter the new

area code. Or you can

use

/RocketDial/

or call id/ to move

the cursor and edit the

area code.

INT1100 Manual-5.0.qxd 1/29/04 12:09 AM Page 14 Bob's Garage: New Backup: Clients:CoastlineCreative:Clients:Int

[ 15 ]

GETTING STARTED

Language option can be used to choose the language of your display. You can select English,

French, or Spanish.

1) When the phone is in the standby mode, press

menu/mute.

2) Press

+ or - to move the pointer to “Language“,

then press

select/ch.

3) Press

+ or - to choose English, French (Français), or

Spanish (Español).

4) Press

select/ch, and you will hear a confirmation tone.

5) Press

end to exit.

Selecting a Language

INT1100 Manual-5.0.qxd 1/29/04 12:09 AM Page 15 Bob's Garage: New Backup: Clients:CoastlineCreative:Clients:Int

[ 16 ]

On the handset, you may also use the speakerphone while talking on your phone. Using

the handset speakerphone is called “hands-free conversation”. This feature allows you to

easily communicate while performing other tasks, such as cooking. appears during

hands-free conversation.

You can easily switch a call from normal conversation to “hands-free conversation”.

To switch a call, press

spkr during the call.

BASICS

Making and Receiving Calls

• Refer to page 13

“Setting Caller ID

Options” to turn the

AutoTalk feature On if

desired. Any key answer

can be used only when

AutoTalk is set to On.

• The handset microphone

is located on the bottom

of the handset (see

“Controls and Functions”

on page 5). Position

yourself as near to the

handset as possible and

speak clearly.

To answer a call

To make a call

Normal conversation

Handset On the Base

Pick up the handset (AutoTalk)

or pick up

the handset and press

talk/flash.

Handset Off the Base

Press any number key, /tone, or #

(Any Key Answer), or press talk/flash.

Handset Off the Base

1) Press talk/flash.

2) Listen for the dial tone.

3) Dial the number.

OR

Dial the number, then press talk/flash.

Note: If a call is not established, you will hear a beep and “Unavailable” will

appear in the display.

Press end, or return the handset to the base (AutoStandby).

When you dial the number, press

redial/p.

“

P” appears in the display, which represents a pause.

Hands-free conversation

Handset Off the Base

Press spkr.

Handset Off the Base

1) Press spkr.

2) Listen for the dial tone.

3) Dial the number.

OR

Dial the number, then press spkr.

From the Handset

To hang up

To enter a pause within

the dialing sequence

INT1100 Manual-5.0.qxd 1/29/04 12:09 AM Page 16 Bob's Garage: New Backup: Clients:CoastlineCreative:Clients:Int

[ 17 ]

BASICS

Redialing a Call

The last three phone numbers dialed can be quickly redialed.

Redialing from Standby Mode

1) Press redial/p. The phone number that was last dialed

appears on the display.

2) Press

redial/p again. Each press of redial/p will display

one of the last three numbers dialed.

3) Press

talk/flash or spkr. The selected number is dialed.

4) To hang up, press

end.

• If the number exceeds

32 digits, only the first

32 digits are retained

in redial memory.

• If the redial memory is

empty, you will hear

a beep.

Redialing from Talk Mode

1) Press talk/flash or spkr.

2) Press

redial/p. The last number dialed will be displayed and redialed.

3) To hang up, press

end.

• If you have not pressed any key for 30 seconds, the phone

returns to standby mode.

• If you press

end, the operation is canceled and the phone will

return to the standby mode.

When using the redial feature in talk mode, only the last number

dialed will be displayed.

INT1100 Manual-5.0.qxd 1/29/04 12:09 AM Page 17 Bob's Garage: New Backup: Clients:CoastlineCreative:Clients:Int

[ 18 ]

1) When the phone is in the standby mode, press menu/mute.

2) Press

+ or - to move the pointer to “Ringer Volume”.

3) Press

select/ch.

4) Press

+ or - to move the pointer through the ringer settings

(Ringer Off, Ringer Low, or Ringer High).

You will hear a ringer or melody at the selected volume.

5) Press

select/ch, you will hear a confirmation tone.

6) Press

end to exit.

Ringer Mute (temporarily)

You can temporarily mute the ringer tone. When the handset is off the

base and the phone is ringing, press

end. The ringer tone will return to

the previous setting starting with the next incoming call.

• If you select “Ringer Off”,

“

<Ringer Off>” appears in

the display when you

make or

receive calls, or charge

the handset.

Ringer Volume Setup

1) When the phone is in the standby mode, press menu/mute.

Ringer Tone Setting

BASICS

2) Press + or - to move the pointer to “Ringer Tones”,

then press

select/ch.

You can choose from 6 ringers or 4 melodies:

- Ringers [Flicker, Clatter, Leap Frog, Ping Ball, Reminder,

Soft Alert]

- Melodies [Beethoven9, For Elise (Elise), Merry Christmas

(Merry-Xmas), Home Sweet Home (Hm Swt Hm)]

3) Press

+ or - to move the pointer. You will hear the ringer or the

melody as you scroll through the options.

4) Press

select/ch and you will hear a confirmation tone.

5) Press

end to exit.

• If you set the ringer to

Off, the ringer tone will

not sound.

INT1100 Manual-5.0.qxd 1/29/04 12:09 AM Page 18 Bob's Garage: New Backup: Clients:CoastlineCreative:Clients:Int

[ 19 ]

BASICS

• See ”Storing Phone

Numbers, Names,

Distinctive Rings, and

Speed Dial” on page 23

for storing a Distinctive

Ring in the Phonebook.

“Distinctive Ringer” allows you to preset memory locations with a designated ring tone. When

an incoming call is received and the Caller ID information matches the information in one of

the memory locations, the Distinctive Ring that has been stored for that particular caller will

sound.

If you have set multiple memory locations with distinctive rings, switching the setting to

“

Distinctive Off” will result in no distinctive ringing. All incoming calls will have a normal ring

tone. Switching to “

Distinctive On” will activate all programmed distinctive ring memory

locations.

1) When the phone is in the standby mode, press

menu/mute.

2) Press

+ or - to move the pointer to “Distinct. Ring”,

then press

select/ch.

3) Press

+ or - to choose “Distinctive On” or

“

Distinctive Off”.

4) Press

select/ch, and you will hear a confirmation tone.

5) Press

end to exit.

Distinctive Ringer Setup

INT1100 Manual-5.0.qxd 1/29/04 12:09 AM Page 19 Bob's Garage: New Backup: Clients:CoastlineCreative:Clients:Int

[ 20 ]

Adjusting the Earpiece and

Handset Speaker Volume

You can select different volume levels for the handset earpiece and the handset speaker

(Volume Low, Volume Medium, Volume High, and Volume Maximum). The volume can only be

adjusted during a call. Press

+ or - to select the volume settings. When you hang up, the

phone keeps the last volume setting selected.

If you press + in maximum volume level or - in lowest volume level, you will hear a beep.

BASICS

• If you press end to

cancel muting, the call

is disconnected and the

phone will return to

standby mode.

• If you press

xfer/del

while muting, the

muting is canceled.

Mute Microphone

You can temporarily turn Off the microphone so that the person you are

talking with cannot hear you.

During a telephone call press and hold

menu/mute to turn Off the

microphone, and “

Mute” appears on the display. Press menu/mute again

to cancel muting.

INT1100 Manual-5.0.qxd 1/29/04 12:09 AM Page 20 Bob's Garage: New Backup: Clients:CoastlineCreative:Clients:Int

Page is loading ...

Uniden TXC580 User manual

This manual is also suitable for

Uniden TXC580 User manual

Related papers

Other documents