PYLE Audio PYD1270 User manual

Brand: PYLE Audio

Model: PYD1270

Category: Musical Instruments

Type: User manual

This manual is also suitable for

PYD6070

PYLE Audio PYD1270 is a professional 12-channel 2-bus mixing console designed for mixing sound from multiple signal sources. With its wide range of inputs and outputs, the PYD1270 is perfect for use in home or professional recording studios, live sound reinforcement, and more.

Some of the key features of the PYD1270 include:

12 balanced XLR microphone inputs with +48V phantom power
4 balanced 1/4" TRS line inputs
4 balanced 1/4" TRS stereo line inputs
3-band EQ on each channel
Aux send and return jacks for external effects processing
Control room and headphone outputs
Main mix outputs with level control

Some of the key features of the PYD1270 include:

12 balanced XLR microphone inputs with +48V phantom power
4 balanced 1/4" TRS line inputs
4 balanced 1/4" TRS stereo line inputs
3-band EQ on each channel
Aux send and return jacks for external effects processing
Control room and headphone outputs
Main mix outputs with level control

pro series

PYD6070/PYD1270

6/12 channel 2 Bus

professional

mixing console

Your PYLE PRO Series Compact Mixing Console

is a sophisticated control center, perfect for mixing sound from multiple signal sources such as

MICROPHONES, GUITAR, GUITAR AMP,KEYBOARD, SAMPLER, DRUM MACHINE or AUDIO OUTPUT

FROM A VCR.

This mixer is ruggedly constructed for home or professional use. Wide range of volume controls

permit you to adjust sound levels accurately to achieve just the right mix for playing through your

speaker system or for recording.

i – Pyle Pro Mixer PYD6070/1270 Owner’s Manual

Owner’s Manual Table of Contents

i Introduction

1 Safety Instructions

Care and Maintenance

2 Features and Controls: PYD6070 Mixer

3 Features and Controls: PYD1270 Mixer

4 INSTALLATION, PYD6070 Mixers

5 INSTALLATION, PYD1270 Mixers

6 Mono Input Channel Controls,

MIC/LINE/GAIN/EQ/EFX/PAN/PEAK/LEVEL/LO CUT(PYD1270)

CH1/CH2 For PYD6070

CH1/CH2/CH3/CH4 For PYD1270

7 Stereo Input Channel Controls,

LINE/EQ(PYD6070)/EFX/BAL/LEVEL/GAIN(PYD1270)

CH3/4 & CH5/6 For PYD6070

CH5/6, CH7/8, CH9/10, & CH11/12 For PYD1270

8-9 Main Section Connections and Controls

10 Specifications

11 Warranty

Safety Instructions

Pyle Pro Mixer PYD6070/1270 Owner’s Manual – 1

CAUTION: To reduce the risk of electronic shock, do not remove the cover (or back). No user

serviceable parts inside; refer servicing to qualified personnel.

WARNING: To reduce the risk of fire electric shock, do not expose this device to rain and moisture.

This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous

voltage inside the enclosure-voltage that may be sufficient to constitute a risk of shock.

This symbol, wherever it appears, alerts you to important operating and maintenance

instructions in the accompanying literature. Please read the manual.

This device should be kept away from water or liquid to be spilled into the unit.

This device should be kept away from heat sources such as raditors, heat registers, stoves, etc.

This device should be situated so that its location or position does not interfere with its proper

ventilation.

Care and Maintenance

Your PYLE PRO mixer is an example of superior design and craftsmanship.

The following suggestions will help you care for your mixer so you can

enjoy years of use:

• Keep the mixer dry, if it gets wet, wipe immediately.

• Use the mixer only in well ventilated installations.

• Handle the mixer gently and carefully-do not drop.

• Keep the mixer away from dust and dirt.

• Wipe occasionally with a damp cloth to keep it looking new. Do not use harsh chemicals,

solvents or detergents.

2 – Pyle Pro Mixer PYD6070/1270 Owner’s Manual

Features and Controls: PYD6070 Mixer

MIC1 & MIC2 Balanced XLR Input Connector

For connecting a balanced low impedance microphone with XLR type plug.

LINE 1 & LINE 2

BAL or UNBAL

1/4" (TRS)

Input Jack

For connecting a

balanced or

unbalanced line

level sources.

MIC1/LINE 1 &

MIC2/LINE 2

GAIN Control

Lets you adjust

the gain of the

input source.

CH1, CH2,

CH3/4, & CH5/6

Tone Controls

(EQ)

CH1, CH2,

CH3/4, & CH5/6

EFX Control

Lets you adjust the

channel signal level

sent to the external

effect.

CH1 & CH2

PEAK Indicator

Indicates the channel

signal is going into

overload.

CH1 & CH2

PAN Control

Lets you adjust

the channel signal

level feeding the

L & R mix bus.

CH1, CH2, CH3/4, &

CH5/6 LEVEL Control

Lets you adjust the channel

signal level sent to the MAIN

mix bus.

CH3/4 & CH5/6 BAL Control

Lets you adjust the channel signal levels of left and

right relative to each other before both signals are

then sent to the MAIN mix bus.

It allows you to balance the source in the stereo image.

CONTROL ROOM/PHONES Level Control

Lets you adjust the signal level sent to the

control room and headphones.

EFX RETURN Level Control

Lets you adjust the effects signal

level sent to the MIAN mix bus.

MASTER Level Control

Lets you adjust the signal level

of MAIN and TAPE outputs.

PHANTOM +48V

DC Switch with

Indicator

Press to accept the

use of condenser

microphones.

DUAL LED

DISPLAY METER

Indicates the levels

of left and right

MAIN outputs.

TAPE TO CONTROL ROOM Switch

Press to route the signal playback from

tape to the control room.

TAPE TO MIX

Switch

Press to route the

signal playback from

tape to the MAIN

mix bus.

TAPE IN & OUT

Jacks

To connect the

mixer to a tape deck

for recording the

mixed program and

for auditioning mix

playback from tape.

MAIN OUT Jacks

To connect the

mixer to a receiver

or amplifier.

CTRL ROOM OUT Jacks

To connect the mixer to a second receiver

or amplifier powering speakers in the

control room or in a remote location.

POWER ON

Indicator

EFX SEND/RETURN Jacks

Permit you to either include externally generated effects

(such as a digital sampler or synth) IN the mix, or to

process the mixed sound (echo reverb, etc.).

HEADPHONES Jack

Accepts the headphones with 1/4" plug.

LINE 3/4 & LINE

5/6 BAL or

UNBAL 1/4"

(TRS) Input

Jacks

For connecting a

balanced or

unbalanced stereo

line level sources.

Use LEFT input jack

only for each

channel, if the

source signal is

mono.

Features and Controls: PYD1270 Mixer

Pyle Pro Mixer PYD6070/1270 Owner’s Manual – 3

MIC1/MIC2/MIC3 & MIC4 Balanced XLR

Input Connector

For connecting a balanced low impedance

microphone with XLR type plug.

LINE 1, LINE 2, LINE 3, & LINE 4 BAL or

UNBAL 1/4" (TRS) Input Jack

For connecting a balanced or unbalanced line

level sources.

MIC1/LINE 1,

MIC2/LINE 2,

MIC3/LINE 3, &

MIC4/LINE 4

GAIN Control

Lets you adjust the

gain of the input

source.

CH1, CH2,

CH3, & CH4

Tone Controls

(EQ)

CH1, CH2, CH3,

CH4, CH5/6,

CH7/8, CH9/10,

& CH11/12 EFX

Control

Lets you adjust

the channel signal

level sent to the

external effect.

CH1, CH2, CH3, & CH4 PAN Control

Lets you adjust the channel signal level

feeding theL&Rmixbus.

CH1, CH2, CH3, CH4, CH5/6, CH7/8,

CH9/10, & CH11/12 LEVEL Control

Lets you adjust the channel signal level

sent to the MAIN mix bus.

CH1, CH2, CH3, & CH4 LO

CUT Switch

Press to eliminate unwanted

low-frequency signal

components.

CH1, CH2, CH3, & CH4

PEAK Indicator

Indicates the channel signal

is going into overload.

CH5/6, CH7/8, CH9/10,

& CH11/12 GAIN

Switch

Press to increase the

channel gain by +12dB.

CH5/6, CH7/8, CH9/10, & CH11/12 BAL Control

Lets you adjust the channel signal levels of left and

right relative to each other before both signals are

then sent to the MAIN mix bus.

It allows you to balance the source in the stereo image.

CONTROL ROOM/PHONES Level Control

Lets you adjust the signal level sent to the

control room and headphones.

EFX SEND Level Control

Lets you adjust the EFFECTS signal

level sent to the EFX SEND.

MASTER Level Control

Lets you adjust the signal level

of MAIN and TAPE outputs.

PHANTOM +48V

DC Switch with

Indicator

Press to accept the

use of condenser

microphones.

DUAL LED

DISPLAY METER

Indicates the

levels of left and

right MAIN

outputs.

EFX TO

CONTROL ROOM

Switch

Press to route the

EFX SEND signal

to the control

room.

TAPE TO MIX

Switch

Press to route the

signal playback

from tape to the

MAIN mix bus.

TAPE TO CONTROL ROOM Switch

Press to route the signal playback from tape to the

control room.

TAPE IN & OUT

Jacks

To connect the

mixer to a tape

deck for recording

the mixed

program and for

auditioning mix

playback from

tape.

MAIN OUT Jacks

To connect the

mixer to a receiver

or amplifier.

POWER ON

Indicator

LINE 5/6, LINE 7/8, LINE 9/10, & LINE 11/12 BAL or UNBAL 1/4"

(TRS) Input Jacks

For connecting a balanced or unbalanced stereo line level sources.

Use LEFT input jack only for each channel, if the source signal is mono.

EFX SEND/RETURN (LINE 11/12 Input) Jacks

Permit you to either include externally generated effects (such as a digital

sampler or synth) IN the mix, or to process the mixed sound (echo reverb,

etc.). Use two 1/4" (TRS) jacks of LINE 11/12 as effect return path, turn

the EFX GAIN of CH 11/12 fully down to avoid undesirable feedback.

HEADPHONES Jack

Accepts the headphones with 1/4" plug.

CTRL ROOM OUT Jacks

To connect the mixer to a second receiver

or amplifier powering speakers in the

control room or in a remote location.

4 – Pyle Pro Mixer PYD6070/1270 Owner’s Manual

INSTALLATION, PYD6070 Mixers

Pyle Pro Mixer PYD6070/1270 Owner’s Manual – 5

INSTALLATION, PYD1270 Mixers

Mono Input Channel Controls

6 – Pyle Pro Mixer PYD6070/1270 Owner’s Manual

MIC

Each mono input channel comes with an XLR

balanced microphone input connector and also

offers a +48V PHANTOM switch to supply power

for condenser microphones. Please mute the

playback/PA loudspeakers system before switching

on +48V PHANTOM power to prevent the switch-

on thumps being directed to the loudspeakers.

Please connect the microphones before switching

on the +48V PHANTOM power supply, do not

connect microphones to the mixer as long as the

phantom power supply is switched on. Wait for

approximately one minute to get the system

stabilized.

LINE

Each mono input channel comes with a balanced

1/4" (TRS) line level input jack. The unbalanced

devices can also be connected to this input.

NOTE

Please use only either the MIC or LINE input of

a channel at any one time, do not use both

simultaneously.

GAIN

This rotary GAIN control adjusts the channel input

gain level. Proper gain setting gives the mixer to

work in the best operating level. Please turn it

to 0 completely whenever you connect or

disconnect a signal source to one of the inputs.

EQ (HI/MID/LO)

ALL the mono input channels has a 3-band

equalizer, all bands provide up to 15dB of cut and

boost, with a centre detent for OFF. The cut-off

frequencies of HI and LO band are 10 kHz and 100

Hz respectively. The MID band is configured as a

peak filter with a center frequency at 1 kHz .

EFX

It enable you to feed channel signal to the external

effect.

PAN

It determines the amount of the channel signal

feeding the left and right mix bus, to locate the

source smoothly across the stereo image. Its

constant-power design ensure the signal is always

maintained at a constant level.

PEAK

It illuminates to warm you the input channel signal

is driven too high, which could cause distortion.

Use the GAIN control to adjust until the LED does

not light.

LEVEL

It determines the level of channel signal in the

MAIN mix bus and provides a clear visual indication

of channel level.

LO CUT (PYD1270)

It is a steep LO CUT filter designed to eliminate

unwanted low frequency hum. It is useful on live

vocals to reduce stage rumble or "popping" noise

from microphone.

CH1/CH2 For PYD6070 CH1/CH2/CH3/CH4 For PYD1270

Pyle Pro Mixer PYD6070/1270 Owner’s Manual – 7

Stereo Input Channel Controls

CH3/4 & CH5/6 For PYD6070

CH5/6, CH7/8, CH9/10

& CH11/12 For PYD1270

LINE, LEFT & RIGHT

Each stereo input channel comes with two balanced

1/4" (TRS) line level input jacks. The unbalanced

devices can also be connected to this input. If

only the jack marked "LEFT" is used, the channel

operate in mono. The stereo channels are designed

to handle typical line level signals.

EQ (PYD6070)

It is similar to those of the mono channels, except

that the EQ is stereo. It is preferable of using two

mono equalizer when EQ-ing a stereo signal to

avoid the discrepancies occurred oftenly between

left and right setting.

EFX

It is similar to those of the mono channels, except

that the EFX SEND buses are both mono, a mono

sum is first taken from the stereo input before

it is sent to the EFX bus.

BAL

It determines the level of left and right input

signals relative to each other before both signals

are then routed to the MAIN stereo mix bus,

allows you to balance the source in the stereo

image. If a stereo channel is run in mono (only

the left input connected), the balance control acts

as a pan in the normal way.

LEVEL

It determines the level of channel signal in the

MAIN mix bus and provides a clear visual indication

of channel level.

GAIN (PYD1270)

It is an input sensitivity switch which used to

select between +12dB (press on) for studio level

and 0dB (press off) for home-recording level.

8 – Pyle Pro Mixer PYD6070/1270 Owner’s Manual

Main Section Connections and Controls

EFX SEND Jack

It is a 1/4" unbalanced jack sends out the signals from mix bus to the external effects unit.

EFX RETURN Jacks/Control (PYD6070)

The EFX RETURN Jacks bring the output of the external effects unit back into the mixer. These jacks

can be used instead as additional line level inputs, but any external effects signal will have to be

brought back into the mixer via a normal stereo channel, it does allow you to use the channel EQ

on the effects return signal. When a normal stereo channel is used as effects return path, the EFX

control of the relevant channel should be turned fully down to

avoid undesirable feedback. If only the LEFT jack is used, the EFX RETURN is operated in MONO

mode. Use the EFX RETURN rotary control to adjust the effects signal levelsent to the MAIN mix

bus.

NOTE:PYD1270 uses two 1/4" (TRS) jacks of LINE 11/12 as EFX RETURN, turn the EFX GAIN of CH

11/12 fully down to avoid undesirable feedback when using this path.

PHONES/CTRL ROOM OUT Jacks

The stereo PHONES jack sends the mix signals to the headphones. The two unbalanced CTRL ROOM

OUT jacks carry the summed effects, main mix signals, and soloed channel signals to the control

room speakers.

POWER ON Indicator

The large size LED indicator illuminated when the mixer power is on.

MAIN OUT Jacks

The MAIN OUT jacks send line level signals from mixer to external devices, for examples, equalizer

or power amplifier.

PYD6070 PYD1270

Pyle Pro Mixer PYD6070/1270 Owner’s Manual – 9

TAPE IN Jacks

The TAPE IN jacks are used to bring the external signal source (Tape Recorder or CD Player) into

the mixer. Like the EFX RETURN jacks, they also can be used as a standard stereo line level input,

in other words, the line or tape output of an power amplifier with source selection switch can also

be connected here for you to listen to additional source.

TAPE OUT Jacks

The TAPE OUT jacks are used send the MAIN mix signal to your recording device. The output level

is adjusted by the MASTER level control.

TAPE TO CONTROL ROOM Switch

Press this switch to monitor signals coming back from tape recorder (TAPE IN) to ensure that they

are recording correctly. Do not use the TAPE TO MIX switch doing this to avoid the feedback loop.

TAPE TO MIX Switch

Press this switch to route the signals from TAPE IN to the MAIN mix.

EFX TO CONTROL ROOM Switch (PYD1270)

Press this switch to monitor the EFX SEND signal in the control room or headphone. The MAIN mix

signal will be muted while routing the EFX SEND signal to the control room.

EFX SEND Control (PYD1270)

Use it to adjust the overall EFX SEND signal level.

PHANTOM Switch/LED Indicator

Press to activate +48V DC power supply on the MIC XLR connectors of all mono channels. The red

LED lights when phantom power is on.

DUAL LED DISPLAY METER

A pair of 5-segment bargraph peak meters displays the MAIN mix level LEFT and RIGHT.

PHONE/CONTROL ROOM Control

Use it to adjust the level of both headphones and main monitor outputs.

MASTER control

Use it to adjust the MAIN mix signal level.

10 – Pyle Pro Mixer PYD6070/1270 Owner’s Manual

Specifications

MONO INPUT CHANNELS

Mic Input electronically balanced

Sensitivity/Impedance ..............................................1.5 mV/600 Ohms

Frequency Response .................................................20 Hz to 20 kHz, +/- 3dB

Distortion ................................................................0.2%, 1 kHz/1.5 mV input

S/N Ratio ................................................................60 dB (with A-WTD)

Line Input electronically balanced

Frequency Response. ................................................20 Hz to 20 kHz, +/- 3dB

Distortion ................................................................0.03%, 1 kHz/150 mV input

Equalization

HI shelving ..............................................................10 kHz, +/- 15 dB

Mid Range ...............................................................1 kHz, +/- 15 dB

Lo Shelving .............................................................100 Hz, +/- 15 dB

STEREO INPUTS CHANNELS

Line Input balanced

Frequency Response .................................................20 Hz to 20 kHz, +/- 3dB

Distortion ................................................................0.03%, 1 kHz/150 mV input

Equalization

HI shelving ..............................................................10 kHz, +/- 15 dB

Mid Range ...............................................................1 kHz, +/- 15 dB

Lo Shelving .............................................................100 Hz, +/- 15 dB

MAIN MIX SECTION

Max Output .............................................................2V unbalanced

EFX Send Max Out....................................................2V unbalanced

Control Room Out.....................................................2V unbalanced

Signal to Noise Ratio.................................................80 dB (with A-WTD)

POWER SOURCE.......................................................AC 15V

DIMENSIONS (WxHxDmm): ..................................PYD6070 213x40x226

.............................................................................PYD1270 270x40x226

Pyle Pro Mixer PYD6070/1270 –11

Owner’s Manual

Please complete warranty card, detach and return

PYLE PRO Audio, Inc.

1600 63rd Street

Brooklyn, NY 11204

Place

Stamp

Here

12 – Pyle Pro Mixer PYD6070/1270

Owner’s Manual

PYLE PRO MIXERS

warranty registration card

Thank you for purchasing this PYLE

product. To activate your

warranty, please mail this card

within 10 days.

Name

Address

City, State ZIP

Model No. Serial #

(if available)

Date of Purchase

Purchased at:

Music Products Store

Catalog Merchandiser

Sound Contractor/Installer Mail Order

Other

Please complete warranty card, detach and return

www.pyleaudio.com

R.A.#: _____________

PYLE PRO Service Center

1600 63rd Street

Brooklyn, NY 11204

You must also include the following items with your return:

• A copy of your sales receipt or other proof of purchase

• A brief letter, indicating the problem you are experiencing with the product

• Include in your letter your return address, daytime phone number and R.A. number

• Also include a check or money order for $20.00 for return

shipping, handling and insurance, or provide your Visa/MC number with expiration date.

Our obligation under this warranty is limited to the repair or replacement

of the defective unit when it is returned to us prepaid. This warranty will

be considered void if the unit was tampered with, improperly serviced or

subject to misuse, neglect or accidental damage.

Limited Warranty

All PYLE PRO products are carefully constructed and tested before shipment.

Units purchased in the USA are warranted to be free of defects in material

and workmanship for two (2) years from the date of purchase. This warranty

is limited to the original retail purchaser of the mixer.

Should the unit fail due to factory defects in material or workmanship, your

unit will be repaired or replaced at the sole discretion of PYLE.

To obtain warranty service, you must first call our Consumer Return Hotline

at (718) 236-6948 to obtain a Return Authorization Number. This R.A. # must

appear on the outside of your package and on all paperwork relating to your

return.

When returning the unit to us for warranty service, it must be carefully

packed and shipped, prepaid, to:

PYLE Audio PYD1270 User manual

Brand: PYLE Audio

Model: PYD1270

Category: Musical Instruments

Type: User manual

This manual is also suitable for

PYD6070

Some of the key features of the PYD1270 include:

12 balanced XLR microphone inputs with +48V phantom power
4 balanced 1/4" TRS line inputs
4 balanced 1/4" TRS stereo line inputs
3-band EQ on each channel
Aux send and return jacks for external effects processing
Control room and headphone outputs
Main mix outputs with level control

Download PDF

report

PYLE Audio PYD1270 User manual

This manual is also suitable for

PYLE Audio PYD1270 User manual

Related papers

Other documents