Garmin eTrex Summit User manual

owner’s

manual

and

reference

guide

eTrex Summit

personal navigator

GARMIN International, Inc.

1200 East 151

st

Street, Olathe, Kansas 66062, U.S.A.

GARMIN (Europe) Ltd.

Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9AQ, U.K.

GARMIN Corporation

No. 68, Jangshu 2

nd

Road., Shijr, Taipei County, Taiwan

www.garmin.com

Part Number 190-00193-00 Rev. D

Covers.indd 02/01/01, 12:26 PM1

GARMIN International, Inc.

1200 East 151st Street, Olathe, Kansas 66062 U.S.A.

Tel. 913/397.8200

Fax 913/397.8282

GARMIN (Europe) Ltd.

Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9AQ, U.K.

Tel. 44/1794.519944

Fax 44/1794.519222

GARMIN Corporation

No. 68, Jangshu 2nd Road., Shijr, Taipei County, Taiwan

Tel. 886/2.2642.8999

Fax 886/2.2642.9099

may be reproduced, copied, transmitted, disseminated, downloaded or stored in

any storage medium, for any purpose without prior written consent of GARMIN

Corporation. GARMIN Corporation hereby grants permission to download a single

copy of this manual onto a hard drive or other electronic storage medium to be

viewed for personal use, provided that such electronic or printed copy of this

manual contains the complete text of this copyright notice and provided further that

any unauthorized commercial distribution of this manual is strictly prohibited.

Information in this manual is subject to change without notice. GARMIN

Corporation reserves the right to change or improve its products and to make

changes in the content without obligation to notify any person or organization of

such changes. Visit the GARMIN website for current updates and supplemental

information concerning the use and operation of this and other GARMIN products.

Website address: www.garmin.com

GARMIN is a registered trademark and eTrex is a trademark of GARMIN Corpora-

tion and may not be used without the express permission of GARMIN Corporation.

February 2001 Part Number 190-00193-00 Rev. D Printed in Taiwan

Covers.indd 02/01/01, 12:26 PM2

1

Introduction

eTrex Summit Registration

Help us better support you by completing your

on-line registration today!

Why should you register your eTrex Summit?

• Notiﬁ cation of Product Updates

• Notiﬁ cation of New Products

• Lost or Stolen unit tracking

Connect to our website (www.garmin.com) and look

for the Product Registration link on the home page.

Thanks for choosing the GARMIN eTrex Summit. If

you have any questions or comments regarding the use

of the eTrex Summit you can visit our website or contact

our Customer Service Department M-F, 8:00-5:00 CST

(except holidays) at 1-800-800-1020.

If you have previously registered your GARMIN

product purchase using a mail-in registration

card, we invite you to reregister using our

NEW on-line system. Many services provided

by our new product registration system are

now being automated and reregistering your

purchase ensures you the best possible support

from GARMIN.

F

Registration

POWER

190-00193-00_0D.indd 02/12/01, 10:07 AM1

2

Introduction

Registration.......................................................................... 1

Warnings and Cautions........................................................ 3

FCC Statement..................................................................... 4

Features ............................................................................... 5

Buttons ................................................................................ 6

Description .......................................................................... 7

Installing the Batteries.......................................................... 8

Getting Started

Calibrating the Electronic Compass .................................... 10

SkyView Page Basics ........................................................... 11

Map Page Basics.................................................................. 12

Pointer Page Basics ............................................................. 13

Elevation Page Basics .......................................................... 14

Menu Page Basics................................................................ 15

Creating a Waypoint ...................................................... 16-17

Heading in the Right Direction .......................................... 18

Cancelling a GOTO ............................................................ 19

Reference Section

SkyView Page Options................................................... 20-21

Map Page Options .............................................................. 22

Pointer Page Options ..................................................... 23-25

Elevation Page .............................................................. 26-29

Mark Waypoint Page...................................................... 30-31

Waypoint Page.................................................................... 32

Review Waypoint Page................................................... 33-34

Routes ........................................................................... 35-37

Tracks............................................................................ 38-40

Calibration..................................................................... 41-43

Setup Page ..................................................................... 43-44

Display Page ....................................................................... 45

Units Page ..................................................................... 45-48

Heading Page................................................................. 50-52

System Page................................................................... 53-55

Appendicies

Appendix A — Speciﬁ cations ............................................. 56

Appendix B — What is GPS?......................................... 57-58

Appendix C — Reciption Tips ............................................ 59

Appendix D — Time Offset Chart....................................... 60

Appendix E — Accessories ................................................. 61

Appendix F — Wiring Diagram.......................................... 62

Appendix G — Troubleshooting ......................................... 63

Appendix H — FAQ’s .................................................... 64-65

Appendix I — Index...................................................... 66-69

Warranty ............................................................................ 70

Table of

Contents

190-00193-00_0D.indd 02/12/01, 10:07 AM2

3

Remove the batteries from your

eTrex Summit if you don’t expect to

use it for several months. Be sure

to observe the proper polarity when

inserting the batteries. Follow the

battery manufacturer’s instructions

on the proper care and handling of

the batteries.

WARNING: If you choose to use the eTrex Summit

in a vehicle, it is the sole responsibility of the owner/

operator of the eTrex Summit to secure the GPS unit so

that it will not cause damage or personal injury in the

event of an accident. Do not mount the eTrex Summit

over airbag panels or in a place where the driver or pas-

sengers are likely to have an impact with it in an accident

or collision.

WARNING: If you choose to use the eTrex Summit in

a vehicle, it is the sole responsibility of the operator of the

vehicle to operate the vehicle in a safe manner, maintain

full surveillance of all driving conditions at all times,

and never become distracted by the eTrex Summit to the

exclusion of safe operating practices. It is unsafe to oper-

ate the eTrex Summit while you are driving. Failure by

the operator of a vehicle equipped with an eTrex Summit

to pay full attention to operating the vehicle and road

conditions while the vehicle is in motion could result

in an accident or collision with property damage and

personal injury.

CAUTION: IT IS THE USER’S RESPONSIBILITY TO

USE THIS PRODUCT PRUDENTLY. THIS PRODUCT IS

INTENDED TO BE USED ONLY AS A TRAVEL AID AND

MUST NOT BE USED FOR ANY PURPOSE REQUIRING

PRECISE MEASUREMENT OF DIRECTION, DISTANCE,

LOCATION, OR TOPOGRAPHY.

CAUTION: The Global Positioning System (GPS) is

operated by the government of the United States, which is

solely responsible for its accuracy and maintenance. The

system is subject to changes which could affect the accu-

racy and performance of all GPS equipment. Although the

eTrex Summit is a precision electronic NAVigation AID

(NAVAID), any NAVAID can be misused or misinterpreted

and, therefore, become unsafe.

Warnings and

Cautions

Introduction

190-00193-00_0D.indd 02/12/01, 10:07 AM3

4

Introduction

The eTrex Summit complies with Part 15 of the FCC

limits for Class B digital devices. This equipment gener-

ates, uses, and can radiate radio frequency energy and, if

not installed or used in accordance with the instructions

may cause harmful interference to radio communications.

There is no guarantee that interference will not

occur in a particular instance. If this equipment does

cause harmful interference to other equipment, try to

correct the problem by relocating the equipment.

Consult an authorized GARMIN dealer or other

qualiﬁ ed service technician if the problem cannot be cor-

rected. Operation is subject to the following conditions:

(1) This device cannot cause harmful interference, and (2)

this device must accept any interference received, includ-

ing interference that may cause undesired operation.

The eTrex Summit does not contain any user-

serviceable parts. Repairs should be made only by an

authorized GARMIN service center. Unauthorized repairs

can void the warranty.

FCC Compliance

Statement

190-00193-00_0D.indd 02/12/01, 10:07 AM4

5

Introduction

The eTrex Summit is a six ounce, 12 channel, hand

held GPS receiver. It has a built-in GPS antenna and only

ﬁ ve user-Buttons. All Buttons are located on either side of

the unit, allowing for simple, one-handed operation that

won’t obstruct your view of the display. It runs for up to

22 hours on two AA batteries in battery save mode.

The eTrex Summit contains a full function GPS, elec-

tronic compass and barometric altimeter. The eTrex

Summit will track barometric pressure and altitude

changes, providing data never before available in such

a small package. Using the built in compass, the eTrex

Summit will provide you with a reliable heading even

while standing still. When moving, the eTrex Summit

will provide you with more data, including speed, direc-

tion of movement, time, distance to destination, and

more.

From these basic features, your eTrex Summit can

provide one more critical beneﬁ t; peace of mind, because,

with the combination of these technologies you’ll know

where you are, where you’ve been and where you’re

going. And since you’ll always know the way back home,

you can concentrate on what you set out to do and enjoy

the great outdoors.

Other features include:

Waypoints:

500 with name and graphic symbol.

Tracks:

Automatic track log; 10 saved tracks.

Routes:

20 Routes that let you navigate through a set

of 50 waypoints.

Trip Computer:

Current speed, average speed, maxi-

mum speed, bearing, elevation, location, time of sunrise/

sunset, trip timer and trip odometer.

Elevation Computer:

Total ascent, total descent,

average ascent, average descent, maximum ascent,

maximum descent, vertical speed, pressure, 12 hour

pressure trend, maximum elevation, and minimum ele-

vation.

NOTE: You should always

be prepared and capable of

navigating without the eTrex

Summit. It is designed to aug-

ment other forms of basic nav-

igation, not entirely replace

them.

Features

190-00193-00_0D.indd 02/12/01, 10:07 AM5

6

Introduction

The UP/DOWN Button:

• Select options on pages and menus

• Adjusts Contrast on SkyView Page

• Zoom in and out on Map Page

• Cycles through trip computer data

• Cycles through elevation computer data

The ENTER Button:

• Conﬁ rms data entry or menu selections

• Displays Options on main pages

• Pressing and holding the ENTER Button

activates the ‘Mark Waypoint’ page

The PAGE Button:

• Switches display pages.

• Allows you to quit a function.

• Pressing and holding the PAGE Button

will turn on the Electronic Compass and

display the Pointer Page.

The POWER Button:

• Turns the unit on and off

• Turns the display backlight on and off

eTrex Summit

Buttons

190-00193-00_0D.indd 02/12/01, 10:07 AM6

7

Introduction

External Power

and

Data Connector

DOWN

Button

UP

Button

ENTER

Button

Internal

GPS Antenna

LCD Display

(with backlight)

POWER

Button

PAGE

Button

Battery

Compartment

Waterproof Case

Barometric

Pressure

Sensor

Compass

Sighting

Marks

eTrex Summit

Description

190-00193-00_0D.indd 02/12/01, 10:07 AM7

8

Introduction

Installing the Batteries

The eTrex Summit operates on two AA batteries (not

included), which are installed at the back of the unit.

To install the batteries, remove the battery cover by turn-

ing the D-ring at the back of the unit 1/4 turn counter-

clockwise. Insert the batteries observing proper polarity.

Attach the battery cover by turning the D-ring 1/4 turn

clockwise. The two AA batteries can last up to 16 hours

during typical use.

D-ring

Battery Cover

Battery

Installation

Lanyard Installation

190-00193-00_0D.indd 02/12/01, 10:08 AM8

9

Getting Started

The Getting Started Section introduces you to the

basic operation of the eTrex Summit. The Reference Sec-

tion shows you how to use all of eTrex Summit’s remain-

ing features.

The First Step

The eTrex Summit’s GPS operates using information

gathered from satellites. To Initialize the eTrex Summit’s

GPS receiver the ﬁ rst time, take your eTrex Summit out-

side and ﬁ nd a large, open area that has a clear view of

the sky. Press and hold the POWER Button to turn the

unit on. You’ll see the Welcome Page for a few seconds

while the eTrex Summit performs a self-test, followed by

the SkyView Page.

NOTE: When you use the eTrex Summit for the

ﬁ rst time, it will take up to ﬁ ve minutes to ﬁ nd

your location. After the ﬁ rst use, eTrex Summit

only needs about 15 to 45 seconds to ﬁ nd your

location.

The eTrex Summit needs to receive at least three

strong satellite signals to ﬁ nd your location. The SkyView

Page shows you graphically eTrex Summit tracking satel-

lites, and the strength of the satellite signals. The status is

also displayed at the top of the page.

When you see the “READY TO NAVIGATE” message

in the status box, eTrex Summit has found your location

and the GPS receiver is initialize and ready for use.

Backlighting and Contrast

If the lighting conditions make it hard for you to see

the screen, adjust the contrast or turn on the backlight.

Press and release the POWER Button from any screen to

turn on the backlight. The backlight is timed to stay on

for 30 seconds. To adjust the screen contrast, press the

PAGE Button until you see The SkyView Page. Press the

UP Button to make the screen darker, press the DOWN

Button to make the screen lighter.

The SkyView Page

The “READY TO NAVIGATE”

message must appear before

you can begin using your eTrex

Summit to navigate.

F

Here We Go

190-00193-00_0D.indd 02/12/01, 10:08 AM9

10

Getting Started

Calibrating the Electronic Compass

The eTrex Summit’s Electronic Compass needs to be

calibrated outdoors after the batteries have been changed

before using the unit for navigation. Failure to calibrate

the Electronic Compass can result in gross inaccuracy of

the compass feature.

Compass Calibration:

1. Press the PAGE Button until the MENU Page is

displayed.

2. Using the UP or DOWN Button, highlight ‘Calibrate’

and press the ENTER Button.

3. Using the UP or DOWN Button, highlight ‘Compass’

and press the ENTER Button.

4. With ‘Start’ highlighted, press the ENTER Button to

begin the calibration.

5. Making sure that the unit is level, rotate the eTrex

Summit slowly two turns in the same direction. On

the display there will be a speed scale that indicates

whether you are rotating the unit ‘Too Fast’, ‘Too

Slow’ or ‘Just Right’. A message will be displayed

when the compass has been successfully calibrated.

NOTE: The eTrex Summit needs to be level

during compass calibration and use. If the unit

is tilted on either axis the compass feature will

become less accurate.

F

The Speed Scale indicates whether

you are ‘TOO SLOW’, ‘JUST

RIGHT’ or ‘TOO FAST’.

Helpful Compass Tips

1. The Electronic Compass will

need to be recalibrated out-

doors every time the batter-

ies are changed.

2. The Electronic Compass will

not be accurate when used in

a car or around items that

radiate a magnetic ﬁ eld.

3. When using the compass, hold

the unit as level as possible.

The more that the unit is tilted,

the less accurate the compass

will become.

Calibrating the

Compass

190-00193-00_0D.indd 02/12/01, 10:08 AM10

11

Getting Started

Selecting a Page

All of the information needed to operate the eTrex

Summit is found on ﬁ ve main “pages” (or display screens).

These pages are The SkyView, Map, Pointer, Elevation and

Menu. Simply press the PAGE Button to switch between

pages.

SkyView Page Basics

The SkyView Page displays the eTrex Summit’s

receiver status. It also shows the strength of the satellite

signals that are being received. If the signals are weak you

may need to try a different location for better reception.

The shorter the signal strength bar, the weaker the signals.

At the top of the page the unit displays the status of the

receiver. The eTrex Summit displays the message ‘Ready

to Navigate’ when the receiver has gathered enough satel-

lite information to begin navigation.

“You”; Your

Location

Status Message

Satellites

The SkyView Page

Satellite Signal

Strength Bar

Satellite

Signals

Location Accuracy

(estimated)

Map Pointer

Menu

SkyView

Elevation

PAG E

Page Basics

190-00193-00_0D.indd 02/12/01, 10:08 AM11

12

Getting Started

Map Page Basics

The Map Page

The Map Page shows where you are (the animated

ﬁ gure) and provides a picture of where you are going.

As you travel, the animated ﬁ gure “walks” and leaves

a “breadcrumb trail” known as a Track Log. Waypoint

names and symbols are also shown on the map.

To help you better visualize the “real world”, eTrex

Summit automatically rotates the map as you move, so

that waypoints that are ahead of you are always displayed

in front of the animated ﬁ gure. In the upper left corner of

the screen, the Map Orientation is displayed.

To make sure you can see your entire trip, the map

scale can be changed from 200 feet to 800 miles. To

increase the map scale, press the UP Button. This will let

you view a larger area in less detail. To decrease the map

scale, press the DOWN Button. This will show a smaller

“You”; your

location

Map

Orientaion

Path to

Destination

Waypoint

Map

Scale

“Trail”

(track log)

On the Map Page, the UP and

DOWN Buttons are used to adjust

the map scale from 200 feet to

800 miles.

Page Basics

190-00193-00_0D.indd 02/12/01, 10:08 AM12

13

Getting Started

On the Pointer Page, the UP and

DOWN Buttons are used to cycle

through different trip data.

Pointer Page Basics

The Pointer Page helps guide you to a destination.

When you’re moving towards a speciﬁ c destination,

the Pointer Page shows you the name of the location,

the distance, time to go and displays a direction arrow

in the Compass Ring. To navigate, simply follow the

arrow. If the arrow is pointing right, turn right until

the arrow is pointing directly ahead and you will arrive

at your destination.

The Compass Ring reﬂ ects your heading (direction

of movement). The eTrex Summit will automatically

select the correct sensor for you based on your speed.

By pressing the UP or DOWN Buttons, you can

cycle through other trip computer information such

as average speed, maximum speed, bearing, lat/lon,

elevation, time of sunrise/sunset, trip timer and trip

odometer.

Compass Ring

Time to

Destination

Straight Line

Distance to the

Destination

Waypoint (Location) Name

Destination

Symbol

The Pointer Page

Selectable Trip

Data

Current Sensor

NOTE: The direction arrow and destination

symbol only appear on the Pointer Page when

you have started a GOTO.

Direction Arrow

(follow this)

F

Heading

Page Basics

190-00193-00_0D.indd 02/12/01, 10:08 AM13

14

Getting Started

Elevation Page Basics

On the Elevation Page, the UP and

DOWN Buttons are used to cycle

through a variety of user-selectable

data.

Elevation

Proﬁ le

Rate of

Ascent/Descent

Current

Elevation

Scale

The Elevation Page

Selectable

Data

The Elevation Page will provide the user with the

current elevation, rate of ascent/descent, and a proﬁ le

of elevation changes over distance or time. The UP or

DOWN Buttons can be used to scroll through a variety

of user selectable data including Pressure, Vertical Speed,

Max Descent, Max Ascent, Avg Descent, Avg Ascent, Total

Descent, Total Ascent, Min Elevation, Max Elevation, and

12 Hour Pressure Trend.

The Altimeter should be calibrated for the

greatest accuracy. See page 42 for more infor-

mation on calibrating the Altimeter.

F

Press ENTER to access the

Elevation Page ‘OPTIONS’.

Page Basics

190-00193-00_0D.indd 02/12/01, 10:08 AM14

15

Getting Started

Menu Page Basics

The Menu Page gives you access to eTrex Summit’s

more advanced features. With the Menu Page you can

create and view waypoints, create a route, save and view

track logs, calibrate the electronic compass and altimeter

or access the system setup features. Information on each

of these advanced features is included in the Reference

Section of this manual.

Changing the Time Zone

Let’s practice using the Menu Page and set the eTrex

Summit to display your local time.

To change the time zone:

1. Using the PAGE Button, switch to the MENU Page.

Using the UP or DOWN Button, highlight ‘SETUP’

and press ENTER. The SETUP Page appears.

2. Using the UP or DOWN Button, highlight ‘TIME’ and

press ENTER.

3. Using the UP or DOWN Button, select the ‘TIME

ZONE’ ﬁ eld and press ENTER.

4. Using the UP or DOWN Button, scroll through the

selections, and press ENTER when you have found

your correct time zone. Press PAGE to get back to

the page of your choice.

You can select your particular

time zone on the TIME page.

The Menu Page

Backlight On

Indicator

Menu Options

Time and Date

Battery

Strength

Page Basics

190-00193-00_0D.indd 02/12/01, 10:08 AM15

16

Getting Started

Discovering the Fun of GPS Navigation

Discovering the fun of using your eTrex Summit is as

easy as taking a quick walk around an open outdoor area.

In this brief exercise, you’ll mark your current location

(your home for example), travel a short distance away,

and then have the eTrex Summit guide you back to where

you started (to get the most out of this exercise, make sure

to walk for at least the time noted for each step).

Creating a Waypoint

The ﬁ rst step in the exercise is to mark your location

as a waypoint so you can return to it later.

NOTE: The eTrex Summit must be “READY TO

NAVIGATE” before you mark a waypoint.

To mark a waypoint:

1. Press and hold the ENTER Button to activate the

MARK WAYPOINT Page.

The waypoint is assigned a numeric name at the time

it is created. You could press ENTER and save the

waypoint now, but there are a couple of other things that

you should take a look at.

The eTrex Summit comes equipped with 29 different

waypoint symbols that can be displayed on the map to

help quickly identify the waypoints.

To change the waypoint symbol:

1. On the MARK WAYPOINT Page, using the UP or

DOWN Button, highlight the small ﬂ ag symbol and

press ENTER. Using the UP or DOWN Button, scroll

through the symbols and highlight the house symbol.

Press ENTER.

The Latitude, Longitude and Ele-

vation are displayed along the

bottom of the MARK WAYPOINT

and REVIEW WAYPOINT Pages.

F

You can select from 29 symbols

to represent a waypoint on the

map.

Let the Fun

Begin

190-00193-00_0D.indd 02/12/01, 10:08 AM16

17

Getting Started

As mentioned earlier the eTrex Summit will assign a

numeric name at the time a waypoint is created. The

assigned name can be easily changed to something more

meaningful to help in identifying the waypoint.

To change the waypoint name:

1 On the MARK WAYPOINT Page, press the UP

or DOWN Button to highlight the Waypoint Name

‘001’. Press ENTER. The EDIT WAYPOINT NAME

Page appears.

2. Press ENTER. Using the UP or DOWN Button,

scroll through the letter selections. Select ‘H’ and

press ENTER. Repeat this process and ﬁ nish the

word ‘HOME’.

3. Using the UP or DOWN Button, highlight the ‘OK’

ﬁ eld and press ENTER. The MARK WAYPOINT Page

appears.

4. Using the UP or DOWN Button, highlight the ‘OK’

ﬁ eld and press ENTER. Your location, named HOME,

is now marked and stored in memory.

Now that you’ve marked your location, it’s time to

go for a walk. Press the PAGE Button and switch to the

Map Page. Walk in a straight line for 2-3 minutes at a

moderate pace and watch the Map Page.

Your location is shown by the ﬁ gure in the middle of

the screen. As you move, watch the animated ﬁ gure walk,

and a line—called a “track”—appear along the path you

have just covered. Now take a sharp right or left turn and

walk for another 2-3 minutes.

Edit Waypoint Name

Map Page

Edit Waypoint

190-00193-00_0D.indd 02/12/01, 10:08 AM17

18

Getting Started

Guidance by GARMIN

It is time to let the eTrex Summit guide you back to

the waypoint we named ‘HOME’ using the GOTO func-

tion. The GOTO function provides you with a straight

line navigation path to your selected destination.

To Start a GOTO:

1. Using the PAGE Button switch to the MENU Page.

2. Using the UP or DOWN Button, highlight ‘WAY-

POINTS’ and press ENTER. The WAYPOINTS Page

appears.

3. Using the UP or DOWN Button, select the tab

containing ‘HOME’ and press ENTER.

4. Using the UP or DOWN Button, select ‘HOME’ and

press ENTER. The REVIEW WAYPOINT Page appears.

5. Using the UP or DOWN Button, highlight ‘GOTO’,

and press ENTER.3

The Compass Page appears and you’re ready to begin

navigating!

Heading in the Right Direction

The eTrex Summit will guide you back to where you

started using the Pointer Page. The pointer shows the

direction of the destination waypoint. Walk in the direc-

tion the arrow is pointing until the arrow points to the top

of the compass ring. If the arrow points to the right, you

need to go to the right. If the arrow points to the left, go

left. When the arrow is pointing straight up, you are on

the correct track!

The destination name, distance to the destination and

time to reach your destination are displayed at the top

of the screen. The sensor that is being used, Compass

or GPS, to determine your heading is displayed above

the pointer. The speed you are traveling is shown at

the bottom of the screen. Once you are getting close to

your destination, eTrex Summit will give you the message

“ARRIVING DESTINATION”.

The pointer tells you what direc-

tion you should move. When the

pointer is pointing right, just

move right until the pointer is

pointing straight up and points

to the moving direction line (see

picture below).

When the pointer points straight

up as shown, you’re on track!

Follow the

Pointer

190-00193-00_0D.indd 02/12/01, 10:08 AM18

Page is loading ...

Garmin eTrex Summit User manual

This manual is also suitable for

Garmin eTrex Summit User manual

Related papers

Other documents