Denon AVR-591 User manual

AV SURROUND RECEIVER

AVR-591

Owner’s Manual

Manuel de l’Utilisateur

Manual del usuario

Simple

version

Version simpliﬁée

Versión sencilla

v

3

Basic

version

Version basique

Versión básica

v

12

Advanced

version

Version avancée

Versión avanzada

v

26

Information

“Part names and functions”

(vpage57)

v

56

Informations

“Nomenclature et fonctions“

(vpage 57)

Información

“Nombres y funciones de las

piezas“ (vpágina 57)

I

ENGLISHFRANCAISESPAÑOL

n

SAFETY PRECAUTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning ﬂash with arrowhead symbol, within an equilateral

triangle, is intended to alert the user to the presence of

uninsulated “dangerous voltage” within the product’s enclosure

that may be of sufﬁcient magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an equilateral triangle is intended

to alert the user to the presence of important operating

and maintenance (servicing) instructions in the literature

accompanying the appliance.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

To completely disconnect this product from the mains, disconnect the plug

from the wall socket outlet.

The mains plug is used to completely interrupt the power supply to the unit

and must be within easy access by the user.

PRECAUTION:

Pour déconnecter complètement ce produit du courant secteur, débranchez

la prise de la prise murale.

La prise secteur est utilisée pour couper complètement l’alimentation de

l’appareil et l’utilisateur doit pouvoir y accéder facilement.

PRECAUCIÓN:

Para desconectar completamente este producto de la alimentación eléctrica,

desconecte el enchufe del enchufe de la pared.

El enchufe de la alimentación eléctrica se utiliza para interrumpir por completo

el suministro de alimentación eléctrica a la unidad y debe de encontrarse en

un lugar al que el usuario tenga fácil acceso.

IMPORTANT SAFETY

INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings.

Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including ampliﬁers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding

type plug has two blades and a third grounding prong. The wide blade or the

third prong are provided for your safety. If the provided plug does not ﬁt into

your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at

plugs, convenience receptacles, and the point where they exit from the

apparatus.

11. Only use attachments/accessories speciﬁed by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table

speciﬁed by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when

unused for long periods of time.

14. Refer all servicing to qualiﬁed service personnel.

Servicing is required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been spilled or

objects have fallen into the apparatus, the apparatus has been exposed to

rain or moisture, does not operate normally, or has been dropped.

15. Batteries shall not be exposed to excessive heat such as sunshine, ﬁre or

the like.

CAUTION:

HOT SURFACE. DO NOT TOUCH.

The top surface over the internal heat sink may become hot

when operating this product continuously.

Do not touch hot areas, especially around the “Hot surface

mark” and the top panel.

PRECAUTION:

SURFACE CHAUDE. NE PAS TOUCHER.

La surface supérieure du dissipateur de chaleur peut devenir

chaude si vous utilisez ce produit en continu.

Ne touchez pas les zones chaudes, tout particulièrement vers

l’inscription “Hot surface mark” et le panneau supérieur.

PRECAUCIÓN:

SUPERFICIE CALIENTE. NO TOCAR.

La superﬁcie superior sobre el disipador de calor interno

podría llegar a calentarse al operar este producto de forma

continua.

No toque las áreas calientes, especialmente las situadas

alrededor de la “Hot surface mark” y del panel superior.

FCC INFORMATION (For US customers)

1. PRODUCT

This product complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) this product may not cause harmful

interference, and (2) this product must accept any interference received,

including interference that may cause undesired operation.

2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT

This product, when installed as indicated in the instructions contained

in this manual, meets FCC requirements. Modiﬁcation not expressly

approved by DENON may void your authority, granted by the FCC, to use

the product.

3. NOTE

This product has been tested and found to comply with the limits for

a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation.

This product generates, uses and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

product does cause harmful interference to radio or television reception,

which can be determined by turning the product OFF and ON, the user

is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the product into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the local retailer authorized to distribute this type of product or

an experienced radio/TV technician for help.

For Canadian customers:

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du

Canada.

Hot

surface

mark

II

ESPAÑOLENGLISH FRANCAIS

n

NOTES ON USE / OBSERVATIONS RELATIVES A L’UTILISATION / NOTAS SOBRE EL USO

WARNINGS AVERTISSEMENTS ADVERTENCIAS

• Avoid high temperatures.

Allow for sufﬁcient heat dispersion when

installed in a rack.

• Handle the power cord carefully.

Hold the plug when unplugging the cord.

• Keep the unit free from moisture, water, and

dust.

• Unplug the power cord when not using the unit

for long periods of time.

• Do not obstruct the ventilation holes.

• Do not let foreign objects into the unit.

• Do not let insecticides, benzene, and thinner

come in contact with the unit.

• Never disassemble or modify the unit in any way.

• Ventilation should not be impeded by covering

the ventilation openings with items, such as

newspapers, tablecloths or curtains.

• Naked ﬂame sources such as lighted candles

should not be placed on the unit.

• Observe and follow local regulations regarding

battery disposal.

• Do not expose the unit to dripping or splashing

ﬂuids.

• Do not place objects ﬁlled with liquids, such as

vases, on the unit.

• Do not handle the mains cord with wet hands.

• When the switch is in the OFF position, the

equipment is not completely switched off from

MAINS.

• The equipment shall be installed near the

power supply so that the power supply is easily

accessible.

• Eviter des températures élevées.

Tenir compte d’une dispersion de chaleur

sufﬁsante lors de l’installation sur une étagère.

• Manipuler le cordon d’alimentation avec

précaution.

Tenir la prise lors du débranchement du cordon.

• Protéger l’appareil contre l’humidité, l’eau et la

poussière.

• Débrancher le cordon d’alimentation lorsque

l’appareil n’est pas utilisé pendant de longues

périodes.

• Ne pas obstruer les trous d’aération.

• Ne pas laisser des objets étrangers dans

l’appareil.

• Ne pas mettre en contact des insecticides, du

benzène et un diluant avec l’appareil.

• Ne jamais démonter ou modiﬁer l’appareil d’une

manière ou d’une autre.

• Ne pas recouvrir les oriﬁces de ventilation avec

des objets tels que des journaux, nappes ou

rideaux. Cela entraverait la ventilation.

• Ne jamais placer de ﬂamme nue sur l’appareil,

notamment des bougies allumées.

• Veillez à respecter les lois en vigueur lorsque

vous jetez les piles usagées.

• L’appareil ne doit pas être exposé à l’eau ou à

l’humidité.

• Ne pas poser d’objet contenant du liquide, par

exemple un vase, sur l’appareil.

• Ne pas manipuler le cordon d’alimentation avec

les mains mouillées.

• Lorsque l’interrupteur est sur la position OFF,

l’appareil n’est pas complètement déconnecté du

SECTEUR (MAINS).

• L’appareil sera installé près de la source

d’alimentation, de sorte que cette dernière soit

facilement accessible.

• Evite altas temperaturas.

Permite la suﬁciente dispersión del calor cuando

está instalado en la consola.

• Maneje el cordón de energía con cuidado.

Sostenga el enchufe cuando desconecte el

cordón de energía.

• Mantenga el equipo libre de humedad, agua y

polvo.

• Desconecte el cordón de energía cuando no

utilice el equipo por mucho tiempo.

• No obstruya los oriﬁcios de ventilación.

• No deje objetos extraños dentro del equipo.

• No permita el contacto de insecticidas, gasolina

y diluyentes con el equipo.

• Nunca desarme o modiﬁque el equipo de

ninguna manera.

• La ventilación no debe quedar obstruida por

haberse cubierto las aperturas con objetos como

periódicos, manteles o cortinas.

• No deberán colocarse sobre el aparato fuentes

inﬂamables sin protección, como velas

encendidas.

• A la hora de deshacerse de las pilas, respete la

normativa para el cuidado del medio ambiente.

• No exponer el aparato al goteo o salpicaduras

cuando se utilice.

• No colocar sobre el aparato objetos llenos de

líquido, como jarros.

• No maneje el cable de alimentación con las

manos mojadas.

• Cuando el interruptor está en la posición OFF, el

equipo no está completamente desconectado de

la alimentación MAINS.

• El equipo se instalará cerca de la fuente de

alimentación de manera que resulte fácil acceder

a ella.

n CAUTIONS ON INSTALLATION

PRÉCAUTIONS D’INSTALLATION

EMPLAZAMIENTO DE LA INSTALACIÓN

z z

z

Wall

Paroi

Pared

z

zFor proper heat dispersal, do not install this unit in a conﬁned

space, such as a bookcase or similar enclosure.

• More than 0.3 m (12 in.) is recommended.

• Do not place any other equipment on this unit.

zPour permettre la dissipation de chaleur requise, n’installez

pas cette unité dans un espace conﬁné tel qu’une bibliothèque

ou un endroit similaire.

• Une distance de plus de 0.3 m (12 po) est recommandée.

• Ne placez aucun matériel sur cet appareil.

zPara la dispersión del calor adecuadamente, no instale este

equipo en un lugar conﬁnado tal como una librería o unidad

similar.

• Se recomienda dejar más de 0.3 m (12 pulg.) alrededor.

• No coloque ningún otro equipo sobre la unidad.

1

ENGLISH

Basic version Advanced versionSimple version Information

Thank you for purchasing this DENON product. To ensure proper operation, please read these owner’s manual carefully before using the product.

After reading them, be sure to keep them for future reference.

Getting started

Accessories

Check that the following parts are supplied with the product.

q Owner’s manual ...................................................................... 1

w Warranty (for North America model only) ................................1

e Service network list ................................................................. 1

r Remote control unit (RC-1147) ................................................ 1

t R6/AA batteries ....................................................................... 2

y Setup microphone

(DM-A409, Cord length: Approx. 25 ft / 7.6 m) .......................1

u AM loop antenna ..................................................................... 1

i FM indoor antenna .................................................................. 1

r u iy

About this manual

n Operation buttons

The operations described in this manual are based mainly on use of

the remote control unit buttons.

n Symbols

v

This symbol indicates a reference page on which

related information is described.

This symbol indicates a supplementary information

and tips for operations.

NOTE

This symbol indicates points to remember operations

or function limitations.

n Illustrations

Note that the illustrations in these instructions may differ from the

actual unit for explanation purposes.

Simple version (Simple setup guide) ··························3

Basic version ··········································································12

Connections ·················································································13

Important information ·································································13

Connecting an HDMI-compatible device ····································14

Connecting a TV··········································································16

Connecting a Blu-ray Disc player / DVD player ···························16

Connecting a set-top box (Satellite tuner/cable TV) ····················17

Connecting a digital camcorder ··················································17

Connecting a control dock for iPod ·············································18

Connecting an antenna ·······························································18

Playback (Basic operation) ·························································19

Important information ·································································19

Playing a Blu-ray Disc player/DVD player ····································20

Playing an iPod

®

·········································································20

Tuning in radio stations ·······························································22

Selecting a listening mode (Surround mode) ··························23

Standard playback ·······································································23

DENON original surround playback ·············································25

Stereo playback ··········································································25

Direct playback ···········································································25

Advanced version ·······························································26

Speaker installation/connection (Other than 5.1-channel) ·····27

Install ··························································································27

Connect ······················································································28

Set up speakers ·········································································29

Playback (Advanced operation) ·················································30

Convenient functions ··································································30

How to make detailed settings ··················································33

Menu map ··················································································33

Examples of on-screen display and front display ························34

Inputting characters ···································································35

Input Setup ·················································································36

Audio Adjust ···············································································41

Manual Setup··············································································46

Information ·················································································51

Operating the connected devices by remote control unit ······52

Operating AV equipment ····························································52

Registering preset codes ····························································52

Operating components ·······························································54

Resetting the remote control unit ···············································55

Information ·············································································56

Part names and functions···························································57

Front panel ··················································································57

Display ························································································57

Rear panel ···················································································58

Remote control unit ····································································59

Other information ·······································································61

Trademark information ································································61

Surround ·····················································································62

Explanation of terms ···································································66

Troubleshooting ··········································································68

Resetting the microprocessor ····················································70

Speciﬁcations ··············································································70

Contents

Getting started ··············································································1

Accessories ··················································································1

About this manual ·········································································1

Features ························································································2

Cautions on handling ····································································2

2

ENGLISH

Cautions on handling

• Before turning the power switch on

Check once again that all connections are correct and that there are

no problems with the connection cables.

• Power is supplied to some of the circuitry even when the unit is

set to the standby mode. When traveling or leaving home for long

periods of time, be sure to unplug the power cord from the power

outlet.

• About Condensation

If there is a major difference in temperature between the inside of

the unit and the surroundings, condensation (dew) may form on

the operating parts inside the unit, causing the unit not to operate

properly.

If this happens, let the unit sit for an hour or two with the power

turned off and wait until there is little difference in temperature

before using the unit.

• Cautions on using mobile phones

Using a mobile phone near this unit may result in noise. If so, move

the mobile phone away from this unit when it is in use.

• Moving the unit

Turn off the power and unplug the power cord from the power

outlet. Next, disconnect the connection cables to other system units

before moving the unit.

• About Care

• Wipe the cabinet and control panel clean with a soft cloth.

• Follow the instructions when using a chemical cleaner.

• Benzene, paint thinner or other organic solvents as well as

insecticide may cause material changes and discoloration if brought

into contact with the unit, and should, therefore, not be used.

Features

Fully Discrete, identical quality and power for all

5 channels (120 W x 5ch)

The unit is equipped with a power ampliﬁer that plays back high-

ﬁdelity sound in surround mode with equal quality and power for all

channels, true to the original sound.

The power ampliﬁer circuit adopts a discrete-circuit conﬁguration

that achieves high-quality surround sound play back.

Supports HDMI 1.4 with 3D, ARC, Deep Color,

“x.v.Color” , Auto Lipsync and HDMI control

function

This unit can output 3D video signals input from a Blu-ray Disc

player to a TV that supports a 3D system. This unit also supports

the ARC (Audio Return Channel) function, which plays back TV

sound with this unit via an HDMI cable used for connecting the

unit and a TV

z

.

zThe TV should support the ARC function.

4-HDMI inputs and 1-output

The unit is equipped with 4 HDMI input connectors for connecting

devices with HDMI connectors, such as a Blu-ray Disc player,

game machine, HD video camera, etc.

High Deﬁnition Audio Support

The unit is equipped with a decoder which supports high-quality

digital audio format for Blu-ray Disc players such as Dolby TrueHD,

DTS-HD Master Audio, etc.

Dolby Pro Logicgz

The unit is provided with a Dolby Pro Logicgz decoder. When you

play back the sound in Dolby Pro Logicgz playback with front height

speakers connected to the unit, you can enjoy playback sound with

rich spacial expression.

Easy to use, On Screen Display

Simple settings are enabled with the setting menus displayed on

the TV screen. When you control the sound volume, the volume

level is displayed on the screen, and when you switch the input

source, the name of the input source is displayed.

Auto setup function

The unit is provided with an “Auto setup function” which

automatically makes speaker settings best suited for the listening

environment. The sound from the speakers is picked up with the

supplied microphone. Reﬂecting sound and audio characteristics of

speakers are measured, and settings for an optimum sound ﬁeld

are automatically made.

Upconverting of all types of source video signals

to HDMI signals

This unit is provided with functions for automatic conversion of

various video signals (component video, S-Video, video) that are

input to this unit into HDMI signals for output to a monitor, allowing

connection between this unit and a TV to be made with a single

HDMI cable.

Dock connecrivity for iPod and network streaming

If an optional DENON control dock for iPod (ASD-3N, ASD-3W,

ASD-51N or ASD-51W) is connected to this unit, you can listen to

Internet radio or enjoy music and photos stored in your PC.

zAn Internet connection environment is required.

Simple

version

3

ENGLISH

Basic version Advanced version InformationSimple version

Simple version (Simple setup guide)

Here, we explain the entire setup procedure, from unboxing the unit to using it in a home theater.

The “Simple version” describes the installation, connection and setup methods for 5.1-channel speakers.

See page 27 for the installation, connection and setup methods for speakers other than 5.1-channel speakers.

n Before connecting the unit, turn off the power to all devices.

n For operation of the connected devices, refer to the user manuals for each device.

Play back

disc

(vpage11)

Enjoy Blu-ray Disc and DVD

in surround sound.

5

Set up

speakers

(vpage6)

Use the setup microphone

(DM-A409) included with

the product, for automatic

setup.

4

Turn on

power

(vpage6)

3

Connect

(vpage4)

Connect 5.1-channel

speakers, a TV and Blu-

ray Disc player equipped

with an HDMI connector.

2

Install

(vpage4)

Enjoy better audio, using

the correct install method.

1

Set Up Speakers (Audyssey

®

Auto Setup)

Finish

Step 5

Store

Step 4

Check

Step 3

Calculating

Step 2

Measurement

Step 1

Speaker

Detection

Preparation

4

ENGLISH

Speakers

Carefully check the left (L) and right (R)

channels and + (red) and – (black) polarities

on the speakers being connected to the

this unit, and be sure to interconnect the

channels and polarities correctly.

Connecting the speaker cables

Peel off about 0.03 ft/10 mm of sheathing from

the tip of the speaker cable, then either twist the

core wire tightly or terminate it.

When using a banana plug

Tighten the speaker terminal ﬁrmly before

inserting the banana plug.

NOTE

• Connect so that the speaker cable core wires

do not protrude from the speaker terminal.

The protection circuit may be activated if the

core wires touch the rear panel or if the + and –

sides touch each other (vpage67 “Protection

Circuit”).

• Never touch the speaker terminals while the

power supply is connected. Doing so could

result in electric shock.

• Use speakers with the speaker impedances

shown below.

Speaker terminals

Speaker

impedance

FRONT

6 – 16 ΩCENTER

SURROUND

Install

1 2 4 53

This unit can perform 2.0/2.1 to 7.1-channel surround playback.

Here, we explain setup using the example of 5.1-channel speaker

playback.

FL FR

SW

C

SL

SR

120˚

22 – 30˚

Listening position

FL Front speaker (L) • Install the surround speakers in a position

2 to 3 ft (60 to 90 cm) higher than ear

level.

Surround

speaker

2 – 3 ft /

60 – 90 cm

GViewed from the sideH

Front

speaker

FR Front speaker (R)

C Center speaker

SW Subwoofer

SL Surround speaker (L)

SR Surround speaker (R)

1

Connect

1 2 4 53

2

The “Simple version” describes the installation, connection and setup methods for 5.1-channel speakers.

See page 27 for the installation, connection and setup methods for speakers other than 5.1-channel speakers.

5

ENGLISH

Basic version Advanced version InformationSimple version

Blu-ray Disc player and TV

Use only HDMI (High Deﬁnition Multimedia Interface) cable that bears the HDMI logo

(genuine HDMI product). Using cable without the HDMI logo (non-genuine HDMI

product) may result in abnormal playback.

When outputting Deep Color or 1080p, etc., we recommend you use “High Speed

HDMI cable” or “High Speed HDMI cable with Ethernet” for enhanced high-quality

playback.

IN

HDMI

OUT

HDMI

To household power outlet

(AC 120 V, 60 Hz)

Power cord

TV

Blu-ray Disc player

HDMI cable

(sold separately)

HDMI cable

(sold separately)

NOTE

• Do not plug in the power cord until all connections have been completed.

• Do not bundle power cords together with connection cables. Doing so can result in humming or noise.

Connect

FL FR

C

SL

SR

SW

Speaker cables

(sold separately)

Audio cable

(sold separately)

Subwoofer

with built-in

ampliﬁer

6

ENGLISH

Set up speakers

(Audyssey

®

Auto Setup)

1 2 4 53

4

The “Simple version” describes the installation, connection and setup methods for 5.1-channel speakers.

See page 27 for the installation, connection and setup methods for speakers other than 5.1-channel speakers.

The acoustic characteristics of the connected speakers and listening room are

measured and the optimum settings are made automatically. This is called

“Audyssey Auto Setup”.

To perform measurement, place the setup microphone in multiple locations all

around the listening area. For best results, we recommend you measure in six

positions, as shown in the illustration (up to six positions).

• When performing Audyssey Auto Setup, MultEQ

®

/Dynamic EQ

®

/Dynamic

Volume™ functions become active (vpage43, 44).

• To set up the speakers manually, use “Speaker Setup” (vpage46) on the menu.

NOTE

• Make the room as quiet as possible. Background noise can disrupt the room measurements. Close

windows, silence cell phones, televisions, radios, air conditioners, ﬂuorescent lights, home appliances,

light dimmers, or other devices as measurements may be affected by these sounds.

• Cell phones should be placed away from all audio electronics during the measurement process as Radio

Frequency Interference (RFI) may cause measurement disruptions (even if the cell phone is not in use).

• Do not unplug the setup microphone from the main unit until Audyssey Auto Setup is completed.

• Do not stand between the speakers and setup microphone or allow obstacles in the path while the

measurements are being made. This will cause inaccurate readings.

• Loud test sounds may be played during Audyssey Auto setup. This is part of

normal operation. If there is background noise in room, these test signals will

increase in volume.

• Operating

VOL df during the measurements will cancel the measurements.

• Measurement cannot be performed when headphones are connected.

Turn on power

1 2 4 53

3

1

Turn on the TV and subwoofer

power.

Power on

2

Change the TV input to the input of

this unit.

3

Press POWER ON to turn on power

to the unit.

The power indicator ﬂashes green and the

power turns on.

Power on

7

ENGLISH

Basic version Advanced version InformationSimple version

About setup microphone placement

• Measurements are performed by placing the setup microphone successively at multiple positions

throughout the entire listening area, as shown in GExample qH. For best results, we recommend you

measure in six positions, as shown in the illustration (up to six positions).

• Even if the listening environment is small as shown in GExample wH, measuring at multiple points

throughout the listening environment results in more effective correction.

FL SW C FR

SRSL

*

M

FL SW C FR

SRSL

*

M

(

: Measuring positions)

GExample qH GExample wH

(

: Measuring positions)

FL Front speaker (L) SW Subwoofer

FR Front speaker (R) SL Surround speaker (L)

C Center speaker SR Surround speaker (R)

About the main listening position (*M)

The main listening position is the position where listeners would normally sit or where one would

normally sit alone within the listening environment. Before starting Audyssey Auto Setup, place the setup

microphone in the main listening position. Audyssey MultEQ

®

uses the measurements from this position

to calculate speaker distance, level, polarity, and the optimum crossover value for the subwoofer.

The “Simple version” describes the installation, connection and setup methods for 5.1-channel speakers.

See page 27 for the installation, connection and setup methods for speakers other than 5.1-channel speakers.

Set up speakers (Audyssey

®

Auto Setup)

2

Set up

the subwoofer

If using a subwoofer capable of the

following adjustments, set up the

subwoofer as shown below.

n When using a subwoofer with a direct

mode

Set the direct mode to “On” and disable the

volume adjustment and crossover frequency

setting.

n When using a subwoofer without a

direct mode

Make the following settings:

• Volume : “12 o’clock position”

• Crossover frequency :

“Maximum/Highest Frequency”

• Low pass ﬁlter : “Off”

• Standby mode : “Off”

1

Set up

the microphone

Mount the setup microphone on a

tripod or stand and place it in the

main listening position.

When placing the setup microphone, adjust

the height of the sound receptor part to the

level of the listener’s ear.

Sound receptor

Setup

microphone

NOTE

• Do not hold the setup microphone in your hand

during measurements.

• Avoid placing the setup microphone close to a

seat back or wall as sound reﬂections may give

inaccurate results.

8

ENGLISH

6

The detected speakers are displayed.

[ENT]:Next

Front Sp. :Yes

Center Sp. :Yes

Subwoofer :Yes

Surround Sp. :Yes

Step1:Speaker Detection

MultEQ

NOTE

If a connected speaker is not displayed, the

speaker may not be connected correctly. Check

the speaker connection.

7

Use ui to select “Next” and then

press ENTER.

8

Move the setup microphone to

position 2, use ui to select “Next”,

and then press ENTER.

The measurement of the second position

starts. Measurements can be made in up to

six positions.

Step2:Measurement

MultEQ

Please place microphone

Cancel

[ENT]:Next

2nd listening position.

at ear height at

If you want to omit measurements from the next

position onward, select “Calculate”.

(Go to

Step 3 Calculating

)

9

Repeat step 8, measuring positions 3

to 6.

When measurement of position 6 is

completed, a “All the measurements were

ﬁnished.” message is displayed.

Step2:Measurement

MultEQ

Retry

Cancel

[ENT]:Calculate

Calculate

All the measurements

were finished.

Set up speakers (Audyssey

®

Auto Setup)

Preparation

3

Set up

the remote control unit

n Set up the operation mode

Press AMP to set the remote control

unit to amplier operation mode.

Press AMP

4

Connect the setup microphone to the

SETUP MIC jack of this unit.

3-1.Audyssey Auto Setup

MultEQ

at ear height at

Normal

Pre Assign:

Start

Cancel

[ENT]:Select [RTN]:Back

Please place microphone

main listening position.

When the setup microphone is

connected, the following screen is

displayed.

Here, we explain setup using the example of

5.1-channel speaker playback.

For setting other than 5.1-channel surround,

select “Pre Assign” and perform steps 3 to 4 of

“Set up speakers” (vpage29).

5

Use ui to select “Start” and then

press ENTER.

When measuring begins, a test tone is

output from each speaker.

• Measuring requires several minutes.

If “Cancel” is selected

“Cancel Auto Setup?” is displayed on the TV

screen. If “Yes” is selected, “Audyssey Auto

Setup” closes.

NOTE

If “Caution” is displayed:

Go to “Error messages” (vpage 10), check

any related items, and perform the necessary

procedures.

If the problem is resolved, return and restart

“Audyssey Auto Setup”.

When performing Audyssey Auto

Setup over again

Press ui to select “Retry”, and then press

ENTER.

When measuring has stopped

q Press ui to select “Cancel”, then press

ENTER.

w Press o p to select “Yes”, then press ENTER.

Setting up the speakers again

Repeat the operation from step 4 of

Preparation

.

Remote control operation

buttons

Move the cursor

(Up/Down/Left/Right)

Conﬁrm the setting Return to previous menu

Step 1

Speaker Detection

Step 2

Measurement

9

ENGLISH

Basic version Advanced version InformationSimple version

Set up speakers (Audyssey

®

Auto Setup)

Step 3

Calculating

Step 4

Check

10

On the

Step 2

screen, use ui

to select “Calculate”, and then press

ENTER.

Measuring results are analyzed, and the

frequency response of each speaker in the

listening room is determined.

Step3:Calculating

MultEQ

Calculating

[----------]

Please wait...

• Analysis takes several minutes to complete. The

time required for this analysis depends on the

number of speakers connected.

The more connected speakers there are, the

longer it takes to perform analysis.

Remote control operation

buttons

Move the cursor

(Up/Down/Left/Right)

Conﬁrm the setting Return to previous menu

NOTE

• If the result differs from the actual connection

status, or if “Caution!” is displayed, see “Error

messages” (vpage10). Then carry out Audyssey

Auto Setup again.

• If the result still differs from the actual connection

status after remeasurement or the error message

still appears, it is possible that the speakers

are not connected properly. Turn this unit off,

check the speaker connections and repeat the

measurement process from the beginning.

• If you change a speaker position or orientation,

perform Audyssey Auto Setup again to obtain

optimal equalizer correction.

11

Use ui to select the item you want

to check, and then press ENTER.

Step4:Check

MultEQ

Please check the results

of the measured item.

Distance Check

Channel Level Check

Crossover Freq.Check

Speaker Config.Check

• Subwoofers may measure a greater reported

distance than the actual distance due to added

electrical delay common in subwoofers.

• If you want to check another item, press

RETURN.

12

Use ui to select “Next” and then

press ENTER.

Step 5

Store

13

Use ui to select “Store” and then

press ENTER.

Save the measuring results.

Step5:Store

MultEQ

Storing

Please wait...

[----------]

Step5:Store

MultEQ

Store

Cancel

[ENT]:Store

Please select “Store”

to store measurement

values.

• Saving the results requires about 10 seconds.

• If you do not want to save the measurement

results, use ui to select “Cancel”, then select

“Yes” using o p. All the measured Audyssey

Auto Setup data will be erased.

NOTE

During saving of measuring results, be sure not to

turn off the power.

Finish

NOTE

After performing Audyssey Auto Setup, do not

change the speaker connections or subwoofer

volume. In event of a change, perform Audyssey

Auto Setup again.

14

Unplug the setup microphone from

the unit’s SETUP MIC jack.

15

Set Dynamic Volume™.

Finish

MultEQ

Storing complete.

Auto Setup is now

Turn on Dynamic Volume?

Yes : No

finished.

[ ]:Select [ENT]:Exit

• For details of Dynamic Volume settings, see

page 44.

n When turning Dynamic Volume on

• Use o to select “Yes”, and then press ENTER.

The unit automatically enters “Evening” mode.

n When turning Dynamic Volume off

• Use p to select “No”, and then press ENTER.

10

ENGLISH

Parameter Check

Enables you to check the measurement results and equalizer

characteristics after Audyssey Auto Setup.

1

Use ui to select “Parameter Check” and then

press ENTER.

2

Use ui to select the item you want to check, then

press ENTER.

3-2.Parameter Check

Speaker Config.Check

Distance Chenck

Channel Level Check

Crossover Freq.Check

Restore

EQ Check

[ENT]:Select [RTN]:Back

Speaker Conﬁg. Check

Distance Check

Channel Level Check

Crossover Freq. Check

EQ Check

Check the speaker conﬁguration.

Check the distance.

Check the channel level.

Check the crossover frequency.

Check the equalizer.

• If “EQ Check” is selected in step 2, press

ui to select equalizing

curve (“Audyssey” or “Audyssey Flat”) to be checked.

Use o p to switch the display between the different speakers.

3

Press RETURN.

The conﬁrmation screen reappears. Repeat steps 2 and 3.

Retrieving Audyssey Auto Setup settings

If you set “Restore” to “Yes”, you can return to Audyssey Auto Setup

measurement result (value calculated at the start by MultEQ

®

) even

when you have changed each setting manually.

Error messages

An error message is displayed if Audyssey

®

Auto Setup could not be completed due to speaker placement, the measurement environment, etc.

If this happens, check the relevant items, be sure to take the necessary measures, then perform Audyssey Auto Setup over again.

NOTE

Be sure to turn off the power before checking speaker connections.

Examples Error details Measures

or

Retry

Cancel

[ENT]:Retry

F

Microphone:None

Speaker :None

Caution

MultEQ

• The connected setup microphone is broken, or a

device other than the supplied setup microphone

is connected.

• Not all speakers could be detected.

• The front L speaker was not properly detected.

• Connect the included setup microphone to the

SETUP MIC jack of this unit.

• Check the speaker connections.

too high or

Retry

Cancel

[ENT]:Retry

F

Ambient noise is

Level is too low.

Caution

MultEQ

• There is too much noise in the room for accurate

measurements to be made.

• Speaker or subwoofer sound is too low for

accurate measurements to be made.

• Either turn off any device generating noise or

move it away.

• Perform again when the surroundings are quieter.

• Check the speaker installation and the direction

in which the speakers are facing.

• Adjust the subwoofer’s volume.

Retry

R :None

Cancel

Skip

Front

Caution

[ ]:Up/Down [ ]:CH

MultEQ

• The displayed speaker could not be detected. • Check the connections of the displayed speaker.

Retry

L :Phase

Cancel

Skip

Front

Caution

[ ]:Up/Down [ ]:CH

MultEQ

• The displayed is connected with the polarities

reversed.

• Check the polarities of the displayed speaker.

• For some speakers, this error message may

be displayed even if the speaker is properly

connected. If you are sure the connection is

correct, press ui to select “Skip”, then press

ENTER.

Remote control operation

buttons

Move the cursor

(Up/Down/Left/Right)

Conﬁrm the setting Return to previous menu

11

ENGLISH

Basic version Advanced version InformationSimple version

Play back disc

1 2 4 53

5

Remote control operation

buttons

Move the cursor

(Up/Down/Left/Right)

Conﬁrm the setting Return to previous menu

1

Press BD to switch an input source

for a player used for playback.

2

Play the component connected to

this unit.

Make the necessary settings on the

player (language setting, subtitles

setting, etc.) beforehand.

3

Adjust the sound volume.

VOL d ··········································· Volume up

VOL f ······································ Volume down

MUTE ·················································· Muting

4

Set the listening mode.

Set the listening mode according to the playback contents

(cinema, music, etc.) or according to your liking (vpage23

“Selecting a listening mode (Surround mode)”).

When power is switched to standby

Press POWER OFF.

GPower indicator status in standby modeH

• Normal standby : Off

• When “HDMI Control” is set to “ON” : Red

You can also switch the power to standby by

pressing ON/STANDBY on the main unit.

NOTE

During power standby, a slight amount of power is consumed. To

totally cut off the power, remove the power cord from the power

outlet.

Basic

version

12

ENGLISH

F Connections

F Playback (Basic operation)

F Selecting a listening mode (Surround mode)

n Refer to the pages indicated below for information on connecting and playing back the various

media and external devices.

Audio and video

PlaybackConnection

TV

vpage14, 16

–

Blu-ray Disc player

vpage14, 16 vpage20

DVD player

vpage14, 16 vpage20

Set-top box (Satellite tuner or cable TV)

vpage14, 17

–

Game console

vpage14

–

Digital camcorder

vpage17

–

Control dock for iPod

vpage18 vpage20

Audio

PlaybackConnection

Radio

vpage18 vpage22

For speaker connections, see page 4.

Basic version

Here, we explain the connections and basic operation methods for this unit.

13

ENGLISH

Advanced versionSimple version InformationBasic version

Converting input video signals for output (Video conversion function)

This unit is equipped with four types of video input connectors (HDMI, Component video, S-Video and

video) and two types of video output connectors (HDMI and video).

Use the connectors corresponding to the components to be connected.

This function automatically converts various formats of video signals input to this unit into the formats used

to output the video signals from this unit to a monitor.

GFlow of video signalsH

HDMI connector

Component video

connectors

S-Video connector

Video connector

Monitor

HDMI connector

Component video

connectors

S-Video connector

Video connector

HDMI

connector

Video connector

HDMI connector

Video connector

Video device

This unit

Output

Input

(IN)

Output

(MONITOR OUT)

Input

Connections

• The video conversion function supports the NTSC, PAL, SECAM, NTSC 4.43, PAL-N, PAL-M and PAL-60

formats.

• Resolutions of HDMI-compatible TVs can be checked at “HDMI Monitor Information” (vpage51).

NOTE

• HDMI signals cannot be converted into analog signals.

• When a non-standard video signal from a game machine or some other source is input, the video

conversion function might not operate.

• Component video input signals cannot be converted into Video format.

Important information

• Connect this unit as follows before using. Make connections according to the equipment you are

connecting.

• Some settings of this unit may be necessary depending on the connection method. Check each

connection item for more information.

• Select the cables (sold separately) according to the components being connected.

NOTE

• Do not plug in the power cord until all connections have been completed.

• When making connections, also refer to the operating instructions of the other components being

connected.

• Be sure to connect the left and right channels properly (left with left, right with right).

• Do not bundle power cords together with connection cables. Doing so can result in noise.

14

ENGLISH

Connecting an HDMI-compatible device

You can connect up to ﬁve HDMI-compatible devices to the unit.

HDMI function

This unit supports the following HDMI functions:

• High resolution video signal

• 3D

• Deep Color (vpage66)

• Auto Lip Sync (vpage48)

• x.v.Color, sYCC601 color, Adobe RGB color, Adobe YCC601color (vpage66, 67)

• High deﬁnition digital audio format

• ARC (Audio Return Channel)

• Content Type

• CEC (HDMI control)

Copyright protection system

In order to play back digital video and audio such as BD-Video or DVD-Video via HDMI connection, both

this unit and TV or the player need to support the copyright protection system known as HDCP (High-

bandwidth Digital Content Protection System). HDCP is copyright protection technology comprised of

data encryption and authentication of the connected AV device. This unit supports HDCP.

• If a device that does not support HDCP is connected, video and audio are not output correctly. Read

the owner’s manual of your television or player for more information.

About HDMI cables

• When a device supporting Deep Color signal transfer is connected, use a cable compatible “High Speed

HDMI cable” or “High Speed HDMI cable with Ethernet”

• When the ARC function is used, connect a device with a ”Standard HDMI cable with Ethernet” or “High

Speed HDMI cable with Ethernet” for HDMI 1.4.

HDMI control function (vpage30)

This function allows you to operate external devices from the receiver and operate the receiver from

external devices.

NOTE

• The HDMI control function may not work depending on the device it is connected to and its settings.

• You cannot operate a TV or Blu-ray Disc player / DVD player that is not compatible with the HDMI control

function.

About 3D function

This unit supports input and output of 3D (3 dimensional) video signals of the HDMI 1.4 standards, For

playing the 3D video content, a player, and a TV that support the 3D function of the HDMI 1.4 standards

are required in addition to this unit.

How the on-screen display is displayed depending on the video

input signal

The way the on-screen display of the menus, status, etc., is displayed differs according to the type of video

signal input to this unit.

n When video signals are input from the HDMI or component video

connectors

• Menu: Switches to a screen with a black background and the menu is superimposed

z

.

• Status display: Not displayed.

z If you want to display the menus superimposed on the picture being played, input the same video

signals to the video connectors. When a menu is displayed, the picture switches to the one being input

from the video connectors and the menu is displayed superimposed over this picture.

n When video signals are being input from the S-Video or video Connectors

• Menu: Menus are displayed superimposed over the picture being played.

• Status display: Displayed.

Examples of on-screen display

• Menu screen • Status display screen

When the input source is

switched

• When the volume is adjusted

MENU

1.Audio Adjust

2.Information

3.Auto Setup

4.Manual Setup

5.Input Setup

[ENT]:Select

MODE:STEREO

IN :DVD

[Auto]

Master Volume -80.0dB

Status display: The operating status is displayed temporarily on the

screen when the input source is switched or the

volume is adjusted.

Important information

15

ENGLISH

Advanced versionSimple version InformationBasic version

About ARC (Audio return channel) function

The Audio Return Channel in HDMI 1.4 enables a TV, via a single HDMI cable, to send audio data “upstream”

to this unit, increasing user ﬂexibility and eliminating the need for any separate S/PDIF audio connection.

NOTE

To enable the ARC function,set “HDMI Control” to “ON” (vpage48).

About Content Type

The HDMI Speciﬁcation Version 1.4 enables simple, automated picture setting selection with no user

intervention.

The Content Type feature enables a display to auto-select the correct viewing mode to match the content

type it is currently receiving from a source device, and to switch modes when a new content source is

selected. Content Type supports content proﬁles for gaming, movie, photograph, and text viewing modes.

NOTE

To enable the Content type, set “Video Mode” to “Auto” (vpage39).

Cables used for connections

Audio and video cable (sold separately)

HDMI cable

• This interface allows transfer of digital video signals and digital audio signals over a single HDMI cable.

OUT

HDMI

OUT

HDMI

OUT

HDMI

OUT

HDMI

IN

HDMI

Blu-ray Disc

player

DVD player TV

Set-top box

Game

console

Connecting an HDMI-compatible device

• When this unit is connected to other devices with HDMI cables, also connect this unit and TV using an

HDMI cable.

• When connecting a device that supports Deep Color transmission, please use a “High Speed HDMI

cable” or “High Speed cable with Ethernet”.

• Video signals are not output if the input video signals do not match the monitor’s resolution. In this case,

switch the Blu-ray Disc/DVD player’s resolution to a resolution with which the monitor is compatible.

• When this unit and monitor are connected with an HDMI cable, if the monitor is not compatible with

HDMI audio signal playback, only the video signals are output to the monitor.

NOTE

The audio signal from the HDMI output connector (sampling frequency, number of channels, etc.) may be

limited by the HDMI audio speciﬁcations of the connected device regarding permissible inputs.

Connecting to a device equipped with a DVI-D connector

When an HDMI/DVI conversion cable (sold separately) is used, the HDMI video signals are converted to

DVI signals, allowing connection to a device equipped with a DVI-D connector.

NOTE

• No sound is output when connected to a device equipped with a DVI-D connector. Make separate audio

connections.

• Signals cannot be output to DVI-D devices that do not support HDCP.

• Depending on the combination of devices, the video signals may not be output.

n Settings related to HDMI connections

Set as necessary. For details, see the respective reference pages.

Input Assign (vpage38)

Set this to change the HDMI input connector to which the input source is assigned.

HDMI Setup (vpage48)

Make settings for HDMI video/audio output.

• Auto Lip Sync

• HDMI Audio Out

• HDMI Control

• Standby Source

• Power Off Control

NOTE

The audio signals output from the HDMI connectors are only the HDMI input signals.

16

ENGLISH

Connecting a TV

• Select the connector to use and connect the device.

• For video connections, see “Converting input video signals for output (Video conversion function)”

(vpage13).

• For instructions on HDMI connections, see “Connecting an HDMI-compatible device” (vpage14).

To listen to TV audio through this device, use the optical digital connection.

NOTE

This connection is not required when a TV compatible with the ARC function (Audio Return Channel (HDMI

1.4 standard function)) is connected to this unit via an HDMI connection.

For details, see “About ARC (Audio return channel) function” (vpage15) or refer to the instruction manual

for your TV.

Cables used for connections

Video cable (sold separately)

Video cable

(Yellow)

Audio cable (sold separately)

Optical cable

IN

VIDEO

AUDIO

OPTICAL

OUT

TV

Set this to change the digital input connector to which the input source is assigned.

“Input Assign” (vpage38)

in Set as Necessary

Connecting a Blu-ray Disc player / DVD player

• You can enjoy video and audio from a Blu-ray Disc or DVD.

• Select the connector to use and connect the device.

• For instructions on HDMI connections, see “Connecting an HDMI-compatible device” (vpage14).

Cables used for connections

Video cable (sold separately)

Video cable

(Yellow)

Audio cable (sold separately)

Audio cable

(White)

(Red)

R

L

R

L

R

L

R

L

VIDEO AUDIO

AUDIO

RL

OUT

VIDEO

Blu-ray Disc player /

DVD player

Set this to change the digital input connector to which the input source is assigned.

“Input Assign” (vpage38)

in Set as Necessary

For HD audio (Dolby TrueHD, DTS-HD, Dolby Digital Plus and DTS Express) playback, connect with HDMI

(vpage14 “Connecting an HDMI-compatible device”).

Page is loading ...

Denon AVR-591 User manual

Denon AVR-591 User manual

Related papers

Other documents