Gigabyte GS-R22T81 User manual

Service Guide

GIGABYTE

GS-R22T61-RH/GS-R22T81-RH

2U Rack Mount Server

Dual Intel

®

Xeon LGA1366 Processor Serverboard

Rev. 1.0

Preface

Before using this information and the product it supports, please read the following general information.

1. This Service Guide provides you with all technical information relating to the BASIC

CONFIGURATION decided for GIGABYTE's “global” product offering. To better fit local market

requirements and enhance product competitiveness, your regional office MAY have decided to

extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability).

These LOCALIZED FEATURES will NOT be covered in this generic service guide. In such

cases, please contact your regional offices or the responsible personnel/channel to

provide you with further technical details.

2. Please note WHEN ORDERING FRU PARTS, you should check the most up-to-date information

available on your regional web or channel. For whatever reason, if a part number change is made,

it will not be noted in the printed Service Guide. For GIGABYTE-AUTHORIZED SERVICE

PROVIDERS, your GIGABYTE office may have a DIFFERENT part number code to those

given in the FRU list of this printed Service Guide. You MUST use the list provided by your

regional GIGABYTE office to order FRU parts for repair and service of customer machines.

3

GS-R22T61-RH/GS-R22T81-RH Rack Mount Server

Table of Contents

Preface....................................................................................................2

Safety, Care and Regulatory Information................................................5

System Specification..............................................................................9

System Hardware Installation................................................................ 11

Chassis Removal and Installation................................................................................. 12

CPU Installation ............................................................................................................... 13

Heat Sink Installation ....................................................................................................... 14

Memory Installation ......................................................................................................... 15

PCI Expansion Card Installation (GC-RLE2N-RH/GC-RFE2N-RH) .......................... 18

PCI Expansion Card Installation (GC-RFX2N-RH/Optional)....................................... 20

GS-R22T81-RH Hard Disk Drive Installation ................................................................ 22

GS-R22T61-RH Hard Disk Drive Installation ................................................................ 23

FAN Duct Removal and Installation .............................................................................. 24

Appearance of GS-R22T61-RH/GS-R22T81-RH ...................................25

Front View of GS-R22T61-RH (For 3.5 HDDs solution).............................................. 25

Front View of GS-R22T81-RH (For 2.5 HDDs solution).............................................. 25

Rear View of GS-R22T61-RH/GS-R22T81-RH ........................................................... 26

Front Panel LED Indicators ............................................................................................. 27

LAN port LED Indicator.................................................................................................... 28

Hard Disk Drive LED Description ................................................................................... 29

GC-BS28E-RH Back plane board Components Description....................................... 30

(for 2.5”HDD) .................................................................................................................... 30

GC-BS26E-RH Back plane board Components Description....................................... 32

(for 3.5”HDD) .................................................................................................................... 32

System Block Diagram................................................................................................... 34

GS-R22T61-RH Cable Routing...................................................................................... 35

.......................................................................................................................................... 35

GS-R22T81-RH Cable Routing...................................................................................... 36

Connector Icon Description............................................................................................. 37

Motherboard Placement and Jumper Setting ......................................38

GA-7TTSH-RH Motherboard Component...................................................................... 38

Motherboard Jumper Setting........................................................................................... 41

Expansion Card Components Description.................................................................... 43

4

Table of Content

BIOS Setup...........................................................................................46

Main...........................................................................................................48

Advanced ...................................................................................................50

Processor Configuration.................................................................................................. 51

Processor Power Management ..................................................................................... 55

Memory Configuration..................................................................................................... 58

Advanced Chipset Configuration ................................................................................... 60

PCI Configuration............................................................................................................. 64

SATA Configuration.......................................................................................................... 66

I/O DeviceConfiguration .................................................................................................. 69

Boot Configuration............................................................................................................ 71

Thermal and Acoustic Configuration.............................................................................. 73

Power.........................................................................................................75

Security ......................................................................................................77

Server.........................................................................................................79

System Management...................................................................................................... 80

Console Redirection........................................................................................................ 82

Event Log Configuration.................................................................................................. 84

Boot............................................................................................................85

Exit .............................................................................................................86

Appexdix A Phoenix BIOS Beep Codes .............................................92

Appexdix B PhoenixBIOS POST Error Messages List ......................96

5

GS-R22T61-RH/GS-R22T81-RH Rack Mount Server

Safety, Care and Regulatory Information

 Important safety information

Read and follow all instructions marked on the product and in the documentation before you operate

your system. Retain all safety and operating instructions for future use.

* The product should be operated only from the type of power source indicated on the rating label.

* If your computer has a voltage selector switch, make sure that the switch is in the proper position for

your area. The voltage selector switch is set at the factory to the correct voltage.

* The plug-socket combination must be accessible at all times because it serves as the main disconnect-

ing device.

* All product shipped with a three-wire electrical grounding-type plug only fits into a grounding-type power

outlet. This is a safety feature. The equipment grounding should be in accordance with local and national

electrical codes. The equipment operates safely when it is used in accordance with its marked electrical

ratings and product usage instructions

* Do not use this product near water or a heat source.

* Set up the product on a stable work surface or so as to ensure stability of the system.

* Openings in the case are provided for ventilation. Do not block or cover these openings. Make sure you

provide adequate space around the system for ventilation when you set up your work area. Never insert

objects of any kind into the ventilation openings.

* To avoid electrical shock, always unplug all power cables and modem cables from the wall outlets

before removing covers.

* Allow the product to cool before removing covers or touching internal components.

 Precaution for Product with Laser Devices

Observe the following precautions for laser devices:

* Do not open the CD-ROM drive, make adjustments, or perform procedures on a laser device other

than those specified in the product's documentation.

* Only authorized service technicians should repair laser devices.

 Precaution for Product with Modems, Telecommunications, ot Local Area

Network Options

Observe the following guidelines when working with options:

* Do not connect or use a modem or telephone during a lightning storm. There may be a risk of electrical

shock from lightning.

6

Safety Information

* To reduce the risk of fire, use only No. 26 AWG or larger telecommunications line cord.

* Do not plug a modem or telephone cable into the network interface controller (NIC) receptacle.

* Disconnect the modem cable before opening a product enclosure, touching or installing internal

components, or touching an uninsulated modem cable or jack.

* Do not use a telephone line to report a gas leak while you are in the vicinity of the leak.

 Federal Communications Commission (FCC) Statement

Warning

This is a class A product. In a domestic environment this product may cause radio

interference

In which case the user may be required to take adequate measures.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Properly shielded and grounded cables and connectors must be used in order to meet FCC emission

limits. Neither the provider nor the manufacturer are responsible for any radio or television interference

caused by using other than recommended cables and connectors or by unauthorized changes or

modifications to this equipment. Unauthorized changes or modifications could void the user's authority to

operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired

operation.

 FCC part 68 (applicable to products fitted with USA modems)

The modem complies with Part 68 of the FCC Rules. On this equipment is a label that contains, among

other information, the FCC registration number and Ringer Equivalence Number (REN) for this equipment.

You must, upon request, provide this information to your telephone company.

If your telephone equipment causes harm to the telephone network, the Telephone Company may

discontinue your service temporarily. If possible, they will notify in advance. But, if advance notice is not

practical, you will be notified as soon as possible. You will be informed of your right to file a complaint with

7

GS-R22T61-RH/GS-R22T81-RH Rack Mount Server

the FCC.

Your telephone company may make changes in its facilities, equipment, operations, or procedures that

could affect proper operation of your equipment. If they do, you will be notified in advance to give you an

opportunity to maintain uninterrupted telephone service.

The FCC prohibits this equipment to be connected to party lines or coin-telephone service.

The FCC also requires the transmitter of a FAX transmission be properly identified (per FCC Rules Part

68, Sec. 68.381 (c) (3)).

/ for Canadian users only /

 Canadian Department of Communications Compliance Statement

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital

apparatus as set out in the radio interference regulations of Industry Canada.

Le present appareil numerique n'emet pas de bruits radioelectriques depassant les limites applicables aux

appareils numeriques de Classe A prescrites dans le reglement sur le brouillage radioelectrique edicte par

Industrie Canada.

 DOC notice (for products fitted with an Industry Canada-compliant modem)

The Canadian Department of Communications label identifies certified equipment. This certification

means that the equipment meets certain telecommunications network protective, operational and safety

requirements. The Department does not guarantee the equipment will operate to the user satisfaction.

Before installing this equipment, users ensure that it is permissible to be connected to the facilities of the

local Telecommunications Company. The equipment must also be installed using an acceptable method

of connection. The customer should be aware that compliance with the above conditions might not prevent

degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated

by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions,

may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility,

telephone lines and internal metallic water pipe system, if resent are connected together. This precaution

may be particularly important in rural areas.

Caution: Users should not attempt to make such connections themselves, but should contact the

appropriate electric inspection authority, or electrician, as appropriate.

8

Safety Information

NOTICE: The Load Number (LN) assigned to each terminal device denotes the percentage of the total

load to be connected to a telephone loop which is used by the device, to prevent overloading. The

termination on a loop may consist of any combination of devices subject only to the requirement that the

sum of the Load Numbers of all the devices does not exceed 100.

/ for European users only /

Class A equipment

This device has been tested and found to comply with the limits for a class A digital device pursuant

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment. This equipment

generate, uses, and can radiate radio frequency energy, and if not installed and used in accordance

with the instructions, may cause harmful interference to radio communication. Operation of this

equipment in a residential area is likely to cause harmful interference, in which case the user will be

required to correct the interference at personal expence.

However, there is no guarantee that interference will not occur in a particular installation. If this

device does cause harmful interference to radio or television reception, which can be determined by

tuning the device off and on, the user is encouraged to try to correct the interference by on or more of

the following measures:

 Reorient or relocate the receiving antenna

 Increase the separation between the device and receiver

 Connect the device into an outlet on a circuit different from that to which the receiver is

connected

 Consult the dealer or an experienced radio/television technician for help

CAUTION

 Danger of explosion if battery is incorrectly

replaced.

 Replace only with the same or equivalent

type recommended by the manufacturer.

 Dispose of used batteries according to the

manufacturer’s instructions.

9

GS-R22T61-RH/GS-R22T81-RH Rack Mount Server

Motherboard  GA-7TTSH1-RH

Processor Supported  Supports dual Intel

®

Xeon

®

processors

 Intel Xeon

®

Dual-Core/Quad-Core processor in LGA 1366 socket

 Supports Intel Quickpath Interconnect up to 6.4 GT/s

Chipset  Northbridge: Intel

®

5520 Chipset

 Southbridge: Intel

®

ICH10R

System Memory:

Memory Capacity  12 x DDR 3 sockets up to 48GB/96GB (1 to 4 GB unbuffered

DIMMs for up to 48GB or 1 to 8 GB registered DIMM for up to

96GB of total system memory)

Memory Type  DDR 3 133 MHz ECC registered/unbuffered DIMMs

DIMM Size  512MB, 1GB, 2GB, 4GB, and 8GB capability modules support

Error Correction:  Single-bit Errors Correction, Multiple Bit Errors Detection

Riser Slot

Full height riser card:  (Top) One PCI-E x8 slot (PCI-E x 8 throughput) , Gen2.

(Black color connector)

 (Middle)One PCI-E x8 slot (PCI-E x 8 throughput) , Gen2.

(Black color connector)

 (Bottom). (Black color connector) PCI-E x8 (PCI-E x8 throughput),

Gen2.

Full height riser card: (Optional) (Top) One PCI-X 64/133MHz (White color connector)

 (Middle)One PCI-E x8 slot (PCI-E x 8 throughput) , Gen2.

(Black color connector)

 (Bottom)One PCI-E x8 slot (PCI-E x 8 throughput) , Gen2.

(Black color connector)

Low-profile riser card:  (Top)One PCI-E x8 slot (PCI-E x 8 throughput), Gen2.

(Black color connector)

 (Middle)One PCI-E x8 slot (PCI-E x4 throughput), Gen1.

(White color connector)

SATA RAID controller  Intel

®

ICH10R

 Supports LSI Software RAID 0/1/10

Cooling Fans:  6 X System Fan

System Specification

10

Feature Summary

Integrated LANs:

Controller  Intel

®

82576EB controller support dual GbE ports

Integrated Graphics:

Controller  Integrated in Server Engines Pilot II

Graphics Memory  32MB DDR2

Mass Storage System  6 x 3.5” Hot-Swap SATA /SAS HDDs

 Or, 16 x 2.5” Hot-Swap SATA /SAS HDDs

 1 x DVD Combo

Super I/O

Controller  ITE IT8720 Super I/O

Front I/O  1 x VGA port

 2 x USB 2.0 dual-port connector

Rear I/O  P/S 2 Keyboard and Mouse Connectors

 1 x Serial port

 4 x USB 2.0 ports

 1 x VGA connector

 2 x GLAN ports

 1 x 10/100 LAN port

System BIOS:

BIOS Type  Phoenix BIOS on 8Mb flash ROM

Server Management Functions: (Optional device)

BMC Chip  Server Engines POLIT 2 IPMI 2.0 controller

Failure Detection  IPMI 2.0 specification of Server management

Event Logging  32KB Nonvolatile Memory to Log System Failure Events

Remote Management  Follow the IPMI 2.0 specification of Server management

Environment

Ambient Temperature  Operating Temperature: 5

o

C to 35

o

C

 Non-operating Temperature: 0

o

C to 50

o

C

Relative Humidity  10-80% operating Humidity at 30

o

C

System Dimention:  432mm x 210mm x 650mm

Electrical Power Supply  Redundant Power Supply 750W

11

GS-R22T61-RH/GS-R22T81-RH Rack Mount Server

Pre-installation Instructions

Perform the steps below before you open the server or before you remove or replace

any component.

1. Back up all important system and data files before performing any hardware

configuration.

2. Turn off the system and all the peripherals connected to it.

3. Unplug all cables from the power outlets.

4. Disconnect all telecommunication cables from their ports.

5. Place the system unit on a flat and stable surface.

6. Open the system according to the instructions.

Warning! Failure to properly turn off the server before you start installing components

may cause serious

damage. Do not attempt the procedures described in the following sections unless you

are a qualified service

technician.

System Hardware Installation

12

Hardware Installation Process

Chassis Removal and Installation

Step 1 Remove the screw on the chassis.

Step 2 Slide toward the top chassis cover.

Step 3 Lift up to remove the top chassis cover.

Step 4 Reverse Step 1, ,2, 3 to replace the chassis cover

1

3

2

13

GS-R22T61-RH/GS-R22T81-RH Rack Mount Server

1

2

3

CPU Installation

Please make sure the CPU type and speed that are supported by the motherboard.

Step 1 Raise the metal locking lever on the socket. Insert the CPU with the correct orientation.

Step 2 The CPU only fits in one orientation.

Step 3 Push the metal lever back into locked position.

14

Hardware Installation Process

Heat Sink Installation

Step 1 Place the Heat Sink on the CPU. Before putting the heat sink on the CPU, please well

remember to apply the thermal conductivity compound on the CPU.

Step 2 Seat the heat sink in the retention modules with the four screws. Installation completed.

1

2

15

GS-R22T61-RH/GS-R22T81-RH Rack Mount Server

Memory Installation

1

2

CPU1

CPU2

DIMMA2

DIMMA1

DIMMB2

DIMMB1

DIMMC2

DIMMC1

DIMMD2

DIMMD1

DIMME2

DIMME1

DIMMF2

DIMMF1

Step 1. Insert the DIMM memory module vertically into the DIMM slot, and push it down.

Step 2. Close the plastic clip at both edges of the DIMM slots to lock the DIMM module.

NOTE! DIMM must be populated in order starting from DIMMA1/D1 sockets. For dualquad

channel operation, DIMMs must be installed in matched pairs.

Step 3. Reverse the installation steps when you wish to remove the DIMM module.

16

Hardware Installation Process

U-DIMM Population Table

DIMMA1/D1

1GB

Interleave

mode

Single

Channel

Dual

Channel

Three

Channel

DIMMA2/D2 DIMMB1/E1 DIMMB2/E2 DIMMC1/F1 DIMMC2/F2

Channel A Channel B Channel C

Total

Memory

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

2GB

4GB

8GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

6GB

12GB

16GB

6GB

3GB

16GB

24GB

17

GS-R22T61-RH/GS-R22T81-RH Rack Mount Server

R-DIMM Population Table

Interleave

mode

Single

Channel

Dual

Channel

Three

Channel

Channel A Channel B Channel C

Total

Memory

DIMMA1/D1

1GB

DIMMA2/D2 DIMMB1/E1 DIMMB2/E2 DIMMC1/F1 DIMMC2/F2

2GB

4GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB 1GB

2GB

4GB

8GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

6GB

12GB

24GB

48GB

8GB

2GB

4GB

8GB

16GB

4GB

8GB

16GB

32GB

3GB

6GB

12GB

24GB

18

Hardware Installation Process

PCI Expansion Card Installation (GC-RLE2N-RH/GC-RFE2N-RH)

Step 1 Loosen the riser bracket screws which attached on on the system.

Step 2 Loosen the rest riser bracket bracket screws.

Step 3 Lift the riser bracket slightly, then pull it out from the server chassis.

Step 4 Slide the expansion card into the slot until the card firmly seats.

Step 5 Slide another expansion card into the slot until the card firmly seats.

Align the riser bracket to the system module.

3

2

1

2

19

GS-R22T61-RH/GS-R22T81-RH Rack Mount Server

4

5

20

Hardware Installation Process

PCI Expansion Card Installation (GC-RFX2N-RH/Optional)

Step 1 Loosen the riser bracket screws which attached on on the system.

Step 2 Loosen the rest riser bracket bracket screws.

Step 3 Lift the riser bracket slightly, then pull it out from the server chassis.

Step 4 Attach the PCI-E card to the riser bracket.

Step 5 Secure the card with screws.

Step 6 Attach anothr PCI-E card to the riser bracket the other side.

Step 7 Secure the card with screws.

Step 8 Align the riser bracket to the system module until it firmly seats.

3

2

1

2

Page is loading ...

Gigabyte GS-R22T81 User manual

This manual is also suitable for

Gigabyte GS-R22T81 User manual

Related papers

Other documents