GE GDT550HGD4WW Installation guide

Brand: GE

Model: GDT550HGD4WW

Category: Dishwashers

Type: Installation guide

This manual is also suitable for

Installation

Built-In Dishwasher

Instructions

Ifyou have questions, call 800.GE.CARES(800.432.2737)or visit our Website at: GEAppliances.com.

InCanada, please call i.800.S6E.3344 or visit www.geappliances.ca

BEFOREYOU BEGIN

Readthese instructions completely and carefully.

A WARNING:

To reduce the risk of electric shock, fire, or injury to

persons, the installer must ensure that the dishwasher is

completely enclosed at the time of installation.

FORPERSONALSAFETY:Remove house fuse or open

circuit breaker before beginning installation. Do not use an

extension cord or adapter plug with this appliance.

The improper connection of the equipment grounding

conductor can result in a risk of electric shock. Check with

a qualified electrician or service representative if you are

in doubt that the appliance is properly grounded.

If house wiring isnot 2-wire with ground, a ground

must be provided by the installer. When house wiring

isaluminum, be sure to use UL-Listed anti-oxidant

compound and aluminum-to-copper connectors.

A CAUTION: oonotremovewoodbaseunt_,

you are ready to install the dishwasher. The dishwasher will

tip over when the door is opened if base isremoved.

A ADVERTENCIA:

Para reducir el riesgo de descarga el6ctrica, incendio o

lesiones a personas, el instalador debe asegurarse de que

el lavaplatos est6 completamente cerrado en el momento

de la instalaci6n.

PARASEGURIDADPERSONAL:Ouite el fusible o abra el

interruptor de circuitos antes de comenzar la instalaci6n.

No utilice un cable de extensi6n o un enchufe adaptador

con este artefacto.

La conexi6n inadecuada del conductor de conexi6n a

tierra del equipamiento puede provocar un riesgo de

descarga el6ctrica. Consulte a un electricista calificado o

representante de servicio t6cnico si tiene dudas sabre la

correcta conexi6n a tierra del aparato.

Siel cableado dom6stico no cuenta con un cable de 2

hilos con conexi6n a tierra, un instalador debe realizar una

conexi6n a tierra. Cuando el cableado dom6stico es de

aluminio, aseg0rese de usar un compuesto antioxidante y

conectores de aluminio a cobre aprobados par UL.

A °

PRECAUCION: No quite la base de

madera hasta que est@listo para instalar el lavaplatos. Sise

quita la base,el lavaplatos sevolcarc_cuando seabra la puerta.

FOR YOUR SAFETY

Read and observe all WARNINGSand CAUTIONSshown

throughout these instructions. While performing installations

described in this booklet, gloves, safety glasses or goggles

should be worn.

IMPORTANT - Observeallgoverning codesand

ordinances.

Note to Installer - Be sure to leave these instructions for the

consumer's and local inspector's use.

, Note to Consumer - Keepthese instructions with your

Owner's Manual for future reference.

Skill Level - Installation of this dishwasher requires

basic mechanical, electrical and plumbing skills. Proper

installation is the responsibility of the installer. Product

failure due to improper installation is not covered under

the GEAppliance Warranty. See warranty information.

Completion Time - :1to 3 Hours. New installations require

more time than replacement installations.

IMPORTANT - ThedishwasherMUSTbeinstalledto

allow for future removal from the enclosure if service is required.

Careshouldbeexercisedwhenthe applianceisinstalledor removed,

to reduce the likelihood of damage to the power supply cord.

If you received a damaged dishwasher, you should immediately

contact your dealer or builder.

Optional Accessories - Seethe Owner's Manual for available

custom panel kits.

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

i,, / //

Printed in the United States 31-31545 09-14 GE

Installation Preparation

PARTS SUPPLIED

IN INSTALLATION PACKAGE:

. Junction box cover and #10 hex-head screw

. Hose clamp

. Drain hose (approximately 78" long)

. Drain hose hanger

.2 #8-18 hex head screws to secure brackets to washer

tub frame

.2 Plug buttons

.2 side trim pieces (some models)

.2 mounting brackets for wood countertops or side

cabinets

.2 #8-18 x 5/8" Phillips special head screws, to secure

dishwasher to underside of countertop or to side

cabinets

Literature, samples and/or coupons

Junction

Box Cover

#10

Hex-Head

Junction

BoxScrew

112" long

Drain Hose Hanger

Hose Clamp

#8 Hex-Head Mounting

Bracket Screws

(onsome models)

Mounting

Brackets

Drain Hose

Plug Buttons

#8 Phillips

Special

Head Screws

5/8" long

MATERIALS YOU WILL NEED:

.90 ° elbow PA" hose internal thread on one end,

opposite end sized to fit water supply)

. Thread seal tape

. UL-listed wire nuts (3)

. Masking Tape

Materials Needed for

New Installations:

. Air gap for drain hose, if required

. Waste tee for house plumbing, if applicable

. Electrical cable or power cord

. Screw-type hose clamps

. Strain relief for electrical connection

. Hand shut-off valve (recommended)

. Hot water line-3/8" minimum, copper tubing

(including ferrule, compression nut) or

GE Part # W×28×326, flexible braided hose

. WD24×10065 drain hose (12' long), if needed

90° Elbow

Thread

Seal Tape

(if applicable)

Waste Tee

Air Gap

Hand

Shut-Off

Valve

HoseClamps

Wire Nuts (3)

Electrical Cable

forPower Cord, if applicable)

Strain Relief

Masking Tape

(if applicable)

Hot Water Line

Optional

12' Drain Hose

Coupler for

optional drain

hose

TOOLS YOU WILL NEED: _.

. Phillips-head screwdriver

. 1/4" and 5/16" nutdriver

. 6" Adjustable wrench Phill

Screwdriver

Level

. Carpenter's square

. Measuring tape

. Safety glasses

. Flashlight 15/16" Socket

Bucket to catch water when flushing the line

. 15/16" socket (optional for skid removal)

Gloves L-________VJ

. Pliers Flashlight

Nutdriver

Pliers

Adjustable

Wrench

Level

Tubing Cutter

Carpenter's

Square

Safety Glasses

For.ew,n tollo ion Only:

. Tubing cutter

. Drill and appropriate bits

Hole saw set

Bucket Gloves Hole SawSet

Measuring Tape

Installation Preparation

PREPARE DISHWASHER ENCLOSURE

AWARNING:

Toreducethe riskofelectricshock,fire,or injuryto persons,the

installermustensurethat the dishwasheriscompletelyenclosedat

thetime of installation.

35-1/2" to 5/4-5/4"

Underside of

Countertop

to Floor

Figure A

ThisWallArea

mustbe Free

of Pipesor

wires

£abinets

Square

and

Plumb

* The rough cabinet opening must be at least 2/4"deep, 2/4"

wide and approximately 34-1/2" high from floor to underside

of the countertop.

A ADVERTENCIA:

Parareducirelriesgode descargael@ctrica,incendioo lesionesa

personas,el instaladordebeasegurarsedeque el lavaplatosest@

completamentecerradoen el momentadela instalaci6n.

* The dishwasher must be installed so that drain hose is no

more than 12' in length for proper drainage.

* The dishwasher must be fully enclosed on the top, sides and

back, and must not support any part of the enclosure.

CLEARANCES: /

• Wheninstalledintoa corner, Countertop

allow 2"rain.clearance

betweendishwasherand

adjacentcabinet,wallorother

appliances.Allow28-5/8"rain.

clearancefrom thefront

of thedishwasherfor door

opening.FigureB.

Figure B

Clearancefor Door

Opening 2" Minimum

DRAIN REQUIREMENTS

, Follow local codes and ordinances.

, Do not exceed 12' distance to drain.

NOTE:Air gap must be used, if waste tee or disposer

connection is less than 18" above floor to prevent siphoning.

DETERMINE DRAIN METHOD

The type of drain installation depends on the following

questions.

. Do local codes or ordinances require an air gap?

. Iswaste tee less than 18"above floor?

If the answer to either question isYES,Method 1 MUST

be used.

. If the answers are NO,either method may be used.

CABINET PREPARATION

, Drill a 1-1/2" diameter hole in the cabinet wall within

the shaded areas shown in Figure A for the drain hose

connection. The hole should be smooth with no sharp edges.

IMPORTANT -When

connectingdrainlinetodisposer,

checktobesurethatdrainplughas

beenremoved.DISHWASHER WILL

NOT DRAIN IFPLUG ISLEFTINPLACE.

4 Remove

Drain

Plug

Figure C

Method 1 - Air Gap with Waste Tee or Disposer

Anair gap mustbe usedwhen requiredbylocalcodesand ordi-

nances.Theair gap must beinstalledaccordingto manufacturer's

instructions.

DrainHoseHanger

Figure D

_Hanger

Method 2 - "High Drain Loop" with Waste Tee or Disposer

Tip: Avoid unnecessary service call charges.

Always be sure disposer drain plug has been removed before

attaching dishwasher drain hose to the disposer.

Installation Preparation

PREPARE ELECTRICAL WIRING

WARNING:

FORPERSONALSAFETY:Removehousefuseor opencircuit breaker

beforebeginninginstallation.Donot usean extensioncordor

adapter plugwith this appliance.

Receptacle \

. I \

Location in Adjacent _ ,,

ADVERTENCIA:

PARASEGURIDADPERSONAL:Quiteelfusibleo abra el interruptor

de circuitosantesde comenzarla instalaci6n.Noutiliceuncable

de extensi6no unenchufeadaptador conesteartefacto.

Electrical Requirements

, This appliance must be supplied with !20V, 60 Hz.,and

connected to an individual properly grounded branch circuit,

protected by a 15- or 20-ampere circuit breaker or time-delay

fuse.

, Wiring must be 2 wire with ground and rated for 75°C(176%).

, If the electrical supply does not meet the above requirements,

call a licensed electrician before proceeding.

Grounding Instructions-Permanent Connection

This appliance must be connected to a grounded metal,

permanent wiring system, or an equipment-grounding

conductor must be run with the circuit conductors and be

connected to the equipment-grounding terminal or lead on

the appliance.

Grounding Instructions-Power Cord Models

This appliance must be grounded. In the event of a malfunction

or breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This appliance is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is installed and

grounded inaccordance with all local codes and ordinances.

AWARNING:

Theimproperconnectionof theequipmentgrounding conductor

can resultin a riskofelectricshock.Checkwith a qualified

electricianor servicerepresentativeifyou are indoubt that

the applianceisproperlygrounded.

Cabinet

Figure E White

For models equipped with power cord: Do not modify the plug

provided with the appliance; if it will not fit the outlet, have a

proper outlet installed by a qualified technician.

Cabinet Preparation & Wire Routing

, Thewiring may enter the opening from either side, rear or the

floor within the shaded area illustrated above in Figure Eand

defined in Figure A.

, Cut a 1-1/2" maximum diameter hole to admit the electrical

cable. Edgesof hole should be smooth and rounded.

Permanent wiring connections may pass through the same

hole as the drain hose and hot water line, if convenient. If

cabinet wall is metal, the hole edge must be covered with a

bushing.

NOTE:Power cords with plug must pass through a separate

hole.

Electrical Connection to Dishwasher

Electrical connection is on the right front of dishwasher.

, For permanent connections the cable must be routed as

shown in Figure E.Cable must extend a minimum of 24" from

the rear wall.

, For power cord connections, install a 3-prong grounding

type receptacle in the sink cabinet rear wall, 6" min. or 18"

maximum from the opening, 6" to 18" above the floor.

, Useonly W×09×70910 or W×09×70911 Dishwasher Power

Cord Kit.

A ADVERTENCIA:

Laconexi6ninadecuadadelconductordeconexi6natierradel

equipamientopuedeprovocarunriesgodedescargael_ctrica.

Consultea unelectricistacalificadoorepresentantedeservicio

t_cnicositienedudassabrelacorrectaconexi6natierradelaparato.

Installation Preparation

PREPARE HOT WATER LINE

NOTE:GErecommends copper tubing for the water line, but if

you choose to useflexible hose, use GE'sW×28×326, flexible

braided hose.

. Thewater supply line (3/8" copper tubing or flexible braided

hose) may enter from either side, rear or floor within the

shaded area shown in Figure F.

. Thewater supply line may pass through the same hole as the

electrical cable and drain hose. Or,cut an additional 1-1/2"

diameter hole to accommodate the water line. If power cord

with plug is used, water line must not pass through power

cord hole.

ACAUTION:

Do not remove wood base until you are ready to install the

dishwasher. The dishwasher will tip over when the door is

opened if base isremoved.

PRECAUCION:

Noquite la base de madera hasta que est_ listo para instalar el

lavaplatos. Sisequita la base, el lavaplatos sevolcar6 cuando

se abra la puerta.

il Shut-off_

Hot

From

Cabinet

FigureF

2" From Floor

Water Line Connection

. If using a flexible braided supply hose, labelthe hose with the

installation date to use as reference. Flexible braided hoses,

elbows and gaskets should be replaced in 5years.

. Turn off the water supply.

. Install a hand shut-off valve in an accessible location, such

as under the sink. (Optional, but strongly recommended and

may be required by local codes.)

. Water connection is on the left side of the dishwasher. Install

the hot water inlet line, using no less than 3/8" copper tubing

or a flexible braided hose. Route the line as shown in Figure F

and extend forward at least 19"from rear wall.

. Adjust water heater for 120°F to 140°Ftemperature.

. Flush water line to clean out debris.

. The hot water supply line pressure must be 20-120 PSI.

Turn page to begin dishwasher installation,

Dishwasher Installation

STEP 1:PREPARATION

Locate the items in the installation package:

, Screws

, Junction box cover

, Drain hose and clamp

, Mounting brackets

, Trim pieces (onsome models)

, Drain hose hanger

, Owner's Manual

, Product samples and/or coupons

STEP 2: CHECK DOOR BALANCE

, With dishwasher on the

wood base, check the

door balance by opening

and closing the door.

, Door isproperly balanced

if, when opened, it self

closes within 20°from

vertical, stays in position

from 20°to 70° and falls

fully open beyond 70°.

Door _

closes /

within /

20 ° /

/ Door stays in

Position from _- _

20°to 70_ . -- -- "_

_Door falls fully __

open beyond 70°_

, Ifnecessary increase or decrease tension as shown. Latch

door and adjust both springs to the same tension setting to

correct balance.

Side View

Make sure

pulley cable

iswithin

pulley

shoulders

Increase

Tension

]

Front View

Decreas_

Tension

Figure G

STEP 3: REMOVE WOOD BASE,

INSTALL LEVELING LEGS

IMPORTANT - Do not kickoffwood base!

Damage will occur.

, Move the dishwasher close to the installation location and lay

it on its back. NOTE:Do not place the dishwasher on its side.

, Remove the 4 leveling legs on the underside of the wood base

with a !5/16" socket wrench.

, Discard base.

Figure H

, Screw leveling legs back into the dishwasher frame,

approximately !/2" from frame as shown.

STEP 4: REMOVE TOEKICK

, Removethe 2 toekick screws and toekick. Set aside for use in

Step 2!.

Toekick Screws

Tip: Make sure door opens and closes smoothly.

Check door opening and closing. If door does not open easily or

falls too quickly, check spring cable routing. The cable is held in

place by "shoulders" on the pulley. Check to be sure cable has

not slipped over the pulley shoulders and isrouted as shown.

Dishwasher Installation

STEP 5: INSTALL 90 ° ELBOW

, Thread 3/4" GHT90°

elbow onto water valve.

Ensure rubber gasket is

located between valve

and elbow, Water Valve

Bracket

, Do not overtighten \

elbow. Water valve

bracket could bend or

water valve fitting could

break.

, Position the end of the

elbow to face the rear of

the dishwasher.

Figure K

Front of dishwasher

90 ° 3/4"

GHT Elbow

Fill Hose

STEP 7: POSITION WATER LINE

AND HOUSE WIRING

, Position water supply line and house wiring on the floor of

the opening to avoid interference with base of dishwasher

and components under dishwasher.

Line Wiring

STEP 6: INSTALL DRAIN HOSE TO DRAIN

LOOP

Connect drain loop end to drain hose using the screw clamp

as shown in the figure.

Figure L

Figure M

STEP 8: INSTALL DRAIN HOSE,

THROUGH CABINET

, Position dishwasher in front of cabinet opening. Insert drain

hose into the hole in cabinet side. If a power cord is used,

guide the end through a separate cabinet opening.

i J

Insulation

Blanket

Line

Ensure drain hose is not

twisted or pinched

Maximum drain hose

length is 15'

Do not disconnect or remove high

drain loop from left side of dishwasher

Figure N

Tip: Prevent unnecessary service call charges for fill, drain

or noise concerns.

Position utility lines so they do not interfere with anything

under or behind the dishwasher.

Dishwasher Instollotion

STEP 9: SLIDE DISHWASHER THREE-FOURTHS

OF THE WAY INTO CABINET

IMPORTANT- oonotpushagainstfrontpanelwith

knees. Damage will occur.

. Grasp the sides of the front panel and slide dishwasher into

the opening a few inches at a time.

STEP li: INSTALL MOUNTING BRACKETS

You will need the mounting brackets and 2 #8 hex-head screws

set aside in Step 1.

You must install the mounting brackets onto the dishwasher

tub frame top or sides prior to sliding the dishwasher into place

under the countertop.

Install mounting brackets on top if the underside of

countertop iswood or wood-like material that accepts screws:

IMPORTANT - Afterinstalling bracketsandbefore

closing the dishwasher door, adjust the brackets by bending

them up as needed, so that they do not contact the top of the

dishwasher door and cause damage.

Figure O

Do not push against

front door panel with

knee. Damage to the

door panel will occur.

. Asyou proceed, pull the drain hose through the opening

under the sink. Stop pushing when the dishwasher extends

about 6 inches forward of adjacent cabinets.

. Make sure drain hose isnot kinked under or behind the

dishwasher.

. Make certain the house wiring, drain lineand water line do

not interfere with components under dishwasher.

STEP 10: INSTALL TRIM PIECES

(on some models)

Skip this step if trim is not supplied with the dishwasher.

Inthis step you will need the trim pieces set aside in Step 1.

. Position the trim pieces so the lips face toward the

dishwasher door.

, Select a trim piece and press it onto the left side tub flange.

Start with the top edge and press the trim piece completely

onto the tub flange as you move towards the bottom. Repeat

for the right side tub flange trim piece.

_J -

)

Figure P

Fully seat to tub flange

If you would like to order the Trim Kitfrom GEService, please

call 800.GE.Cores and request part number WD08×10094 for

BB models or WD08×10096 for WW or CCmodels.

Top Mounting

#8 Bracket

Screw

Dis

tub frame

Bracket

Bend and break here

after installing if

counter has ashort

overhang.

. If you are installing the dishwasher under a counter with a

short overhang, the countertop brackets may extend beyond

the edge of the counter. If this is the case, remove the excess

length by repeatedly bending the brackets at the front notch

only until they break.

Install mounting brackets on sides if the countertop is

granite or similar material that will not accept wood screws:

, Break off front portion of the tab with pliers at the location

shown, prior to attaching to dishwasher.

. Position the left-hand side bracket as shown. Repeat with the

right bracket.

Side Mounting

Dishwasher---___

tub frame -_

#8 Bracket

screw as %

supplied M,

Do not pinch

the latch

wires in

#8 bracket

screw

'/,,,"%

i ub trim

Do not screw into

cabinet face frame

Bend and break

here if necessary

Bracket

Dishwasher Installation

STEP 12: PUSH DISHWASHER INTO

FINAL POSITION

. Checkthe tub insulation blanket, if equipped, to be sure it is

smoothly wrapped around the tub. It should not be "bunched

up" and it must not interfere with the door springs. If the

insulation is "bunched up" or interfering with the springs,

straighten und recenter the blanket prior to sliding the

dishwasher into its finul position.

. Slidethe dishwusher into the final position by pushing on

the sides of the door panel. Do not push or pull the door

in a purtiully open or closed position when moving the

dishwasher. Do not use a knee or push on the center of the

panel. If you do, damage to the panel will likely result.

. The dishwusher is in the final position when the edges of

the front panel ore flush with the adjacent cabinets and the

dishwusher is centered in the cabinet opening. Check that

the dishwasher issqu(]rely positioned in the cabinet opening

(it both the top and the bottom of the (]ppli(]nce prior to

mounting to the cabinet.

IM PO RTANT - Beforeopening thedishwasherdoor,

becertaintheedgesofthedishwasherdoorpanelorebehind

thefaceoftheadjacentcabinetand notup againstthecabinet

face.RefertoFigureQ.Ifthedishwasherdoorisopened

when theedge ofthedoorisagainstthefaceofthecabinet,

dishwasherdoordamage and cabinetdamage willoccur.

. Open and close the dishwasher door to be sure it oper(]tes

smoothly, and does not rub on the adjacent cabinet.

Door

fits and

swings

bac!_

behind

cabinet

frame \

Correct ........

Alignm_

Incorrect Alignment Door catches

Figure Q will result in door damage on cabinet frame

Tip: Prevent unnecessery service charges for panel damage

or wash performance.

Check dishwasher alignment prior to opening dishw(]sher door

to prevent panel damage.

ivl(]kesure utility lines ore not trapped or crushed behind

dishw(]sher. Crushed lines will restrict w(]ter flow.

Check that tub trim does not

contact the door at all points

m Tub frame

X Tub trim

Door

_ ....... Handle

Tub trimmay be trimmedif

necessarytoensureproperdoor

operation

Do not allow tub trim to get

trapped by or come into contact

with the door

Tub trim

trapped

Dishwasher Installation

STEP 13: LEVEL DISHWASHER

IM PORTANT = Dishwasher must be level for proper

dish rack operation, wash performance and door operation.

The dishwasher must be leveled left to right and front to back.

This ensures the dish racks will not roll in or out on their own,

circulation water will flow to the pump inlet, and the door will

close without hitting the side of the tub.

, Remove the lower dish rack and place a level on the door and

lower rack track as shown in Figure R.

. Adjust the level of the dishwasher by individually turning the 4

legs on the bottom of the dishwasher as illustrated in Figure S.

Ensureall 4 legs arefirmly in contact with the floor.

. The dishwasher is properly leveled when the level indicator is

centered left to right and front to back. Also, the dishwasher

door should close without hitting the side of the tub.

. Replace the lower rack.

Tip: Prevent unnecessary service charges. Verify dishwasher

is leveled.

Pullthe dish racks half way out. They should stay put. Open

and close the door. The door should fit in the tub opening

without hitting the side of the tub. If the racks roll on their own,

or the door hits the side of tub, relevel the dishwasher.

Figure R

Check

Front

to Back

Check

Level

Side

to Side

Figure S

Turn Legs

to Adjust //

Dishwasher Installation

STEP 14: POSITION DISHWASHER, SECURE

TO COUNTERTOP OR CABINET

Inthis step you will need the 2 Phillipsspecial head screws

from the screws set aside in Step 1.

The dishwasher must be secured to the countertop or the

cabinet sides. When the underside of the countertop iswood,

use Method 1. UseMethod 2 when the underside of the

countertop is made of a material, such as granite, that will not

accept wood screws.

IMPORTANT - Preventdoor panel and control

panel damage. Dishwasher must be positioned so the front

panel and control panel do not contact the adjacent cabinets

or countertop. Mounting screws must be driven straight and

flush. Protruding screw heads could scratch the door panel or

control panel and interfere with door operation.

Method 1

Secure dishwasher to underside of wood countertop.

. Recheck alignment of the dishwasher in the cabinet, Referto

Steps 12 and 13. Door panel and/or control panel must not

hit cabinets or countertop.

. Fasten the dishwasher to the underside of the countertop

with the 2 Phillips special head screws. Refer to FigureT.

Make certain screws are driven straight and flush to prevent

panel damage,

• Install plug buttons to the side of the tub well in the holes

provided.

Brackets Wood Countertop

/ _ .-

"ill

Method 2

Secure dishwasher to cabinet sides.

. Recheck alignment of the dishwasher in the cabinet. Refer to

Steps 12 and 13. Door panel and/or control panel must not

hit cabinets or countertop.

. Fasten the dishwasher to the adjacent cabinets with the 2

Phillips special head screws provided. Referto Figure U. Make

certain screws are driven straight and flush to prevent panel

damage. Donot screw into the cabinet face frame.

. Install plug buttons to the side of the tub well in the holes

provided.

Solid Surface Countertop

Figure U

. Re-check that the dishwasher is squarely positioned in the

cabinet at both the top and bottom of the appliance after

mounting to the cabinets/countertop. Adjust if necessary.

. Confirm all leveling legs are in contact with the floor to

prevent the dishwasher from rocking and ensure proper door

and latch operation

STEP 15: CONNECT WATER SUPPLY

Connect water supply line to 90°elbow.

If using a flexible braided hose connection:

. Attach nut to 90° elbow using an adjustable wrench.

If using a copper tubing connection:

. Slide compression nut, then ferrule over end of water line.

. Insert water line into 90° elbow.

. Slide ferrule against elbow and secure with compression nut.

IMPORTANT - Check to be surethatdoor spring

and/or door springcabledo not rub or contactthe fillhose or

water supply line,

Test by opening and

closing the door.

Reroute the water

supply lines if a

rubbing noise or

interference

occurs.

Hot Water

Supply Line

no rlk_, _ Compression

....... \. °tX

Ferrule

Figure V

Bottom Left Side

Dishwasher Installation

STEP 16: CONNECT DRAIN LINE

The molded end of the drain hose will fit 5/8" through 1"

diameter inlet ports on the air gap, waste tee or disposer.

. Determine size of inlet port.

. Cut drain hose connector on the marked line, if required,

to fit the inlet port.

Figure W

Cutting Line

,s/83

IMPORTANT: Do not cut corrugated

portion of hose

. If a longer drain hose isrequired and you did not purchase

drain hose WD24×10065, add up to 66" length for a total of

14/4"(12 feet) to the factory-installed hose. Use 5/8" or 7/8"

inside diameter hose and a coupler to connect

the 2 hose ends.

Secure the

connection _

with hose

clamps.

Figure × Hose Clamp

Hose Clamp

Coupler

NOTES:

. DRAIN CONNECTION HEIGHT ISNOTTO EXCEED 72" ABOVE

BOTTOM OF DISHWASHER.

. TOTAL DRAIN HOSE LENGTH MUST NOT EXCEED 12 FEET FOR

PROPER DRAIN OPERATION.

. Connect drain line to air gap, waste tee or disposer

using the previously determined method. Secure hose

with a screw-type clamp.

Method 1- Air gap with waste tee or disposer

Waste TeeInstallation

Figure Y

Disposer Installation

Method 2 - "High drain loop" with waste tee or disposer

With this method you will need the drain hose hanger set aside

in Step 1.

Fasten drain hose to underside of countertop with the provided

hanger.

__ Drain Hose Hunger

WasteTeeInstallation

Figure Z

Disposer Installation

IMPORTANT - When connecting drain line to

disposer, check to be sure that drain plug has been removed.

DISHWASHERWILL NOTDRAINIF PLUGISLEFTIN PLACE.

4 Remove

Drain

Plug

Tip: Avoid unnecessary service call charges for a no drain

complaint.

Make sure excess drain hose has been pulled through

the cabinet opening. This will prevent excess hose in the

dishwasher cavity from becoming kinked or crushed by the

dishwasher.

Dishwasher Installation

STEP 17: CONNECT POWER SUPPLY

If a power cord with plug is already installed proceed to

Step 18.

WARNING:

If housewiringisnot 2-wirewithground,agroundmustbe

providedbythe installer.Whenhousewiring isaluminum,be sure

to useUL-Listedanti-oxidantcompoundand aluminum-to-copper

connectors.

A ADVERTENCIA:

Sielcableadodom_sticonocuentaconuncablede 2hiloscon

conexi6natierra,un instaladordeberealizarunaconexi6na tierra.

Cuandoelcableadodom_sticoesdealuminio,aseg0resedeusar

uncompuestoantioxidanteyconectoresdealuminioa cobre

aprobadosporUL.

In this step you will need the junction box cover and the

#10 Hex head screw from the screws set aside in Step 1.

. Secure house wiring to the back of the junction box with a

strain relief.

. Locate the 3 dishwasher wires, (white, black and green) with

the stripped ends coming out of the ACjumper. Use ULlisted

wire nuts of appropriate sizeto connect incoming ground to

green, white to white and black to black.

. Install the junction box cover using #10 hex head screw.

Check to be sure that wires are not pinched under the cover.

. Make sure that the junction box cover is resting on the

mounting bracket.

NOTE:Do not remove the

Junction Box Bracket.

Ground

White

Jumper

Ground

Screw

Black

Figure AA

NOTE:All ground screws, brackets and wires must remain

intact.

STEP 18:PRETEST CHECKLIST

Review this list after installing your dishwasher to avoid

charges for a service call that is not covered by your

we rra nty.

. Check to be sure power is OFF.

.Open door and remove all foam and paper packaging.

. Locate the Owner's Manual set aside in Step 1.

.Readthe Owner's Manual for operating instructions.

. Check door opening and closing. If door does not open and

close freely, check for proper routing of spring cable over

pulley. If door drops or closes when released, adjust spring

tension. SeeStep 2.

. Check to be sure that wiring issecure under the dishwasher,

not pinched or in contact with door springs or other

components. SeeStep 17.

. Check door alignment with tub. If door hits tub, level

dishwasher. See Step 13.

. Pull lower rack out, about halfway. Check to be sure it does

not roll back or forward on the door. If the rack moves, adjust

leveling legs. See Step 13.

. Check door alignment with cabinet. If door hits cabinet,

reposition dishwasher. See Step 12.

. Check that door spring does not contact water line, fill hose,

wiring or other components. SeeStep 12.

.Verify water supply and drain lines are not kinked or in

contact with other components. Contact with motor or

dishwasher frame could cause noise.

.Turn on the sink hot water faucet and verify water

temperature. Incoming water temperature must be between

120°Fand 140°F.A minimum of 120°F temperature is

required for best wash performance. See"Prepare Hot Water

Line," page 5.

.Add 2 quarts of water to the bottom of the dishwasher to

lubricate the pump seal.

.Turn on water supply. Check for leaks.Tighten connections if

needed.

. Remove protective film if present from the control panel and

door.

. Check that tub trim does not contact the door.

Dishwasher Installation

STEP 19: DISHWASHER WET TEST

.Turn on power supply or plug power cord into outlet,

if equipped.

. Select u cycle to run and push the Start/Reset pad.

. Ensurethe door is latched. Dishwasher should start.

. Checkto be sure that water enters the dishwasher. If water

does not enter the dishwasher, check to be sure that water

and power are turned on.

. Checkfor leaks under the dishwasher. If a leak isfound, turn

off power at the breaker, and then tighten water connections.

Restore power after leak is corrected.

. Checkfor leaks around the door.A leak around the door could

be caused by door rubbing or hitting against

adjacent cabinets. Reposition the dishwasher if necessary.

SeeStep 12.

. Pressend hold the Start/Reset pad for 3 seconds to cancel

the cycle. The unit will begin to drain. Check drain lines. If

leeks ere found, turn off power at the breaker end correct

plumbing us necessary. Restorepower after corrections ere

made. See Steps 6,7,8, 9 end 16.

. Open dishwasher door and make sure oil of the water has

drained. If not, check that disposer plug has been removed

end/or air gap is not plugged. Also check drain hose to be

sure it is not kinked underneath or behind dishwasher. See

Step 16.

. PressStart/Reset pad once again end run dishwasher

through another cycle. Check for leeks end correct if

required.

. Repeat this step us necessary.

STEP 20: POSITION SOUND BARRIER

AND INSULATION

Ion some models}

Skip this step if the sound barrier is not assembled to the

dishwasher.

. Locate the sound insulation package inside the dishwasher.

. Locate the control box.

Control

Box

. Peeloff the paper from the insulation.

. Apply the insulation to the underside of the control box and

flush with its front face as shown.

Insulation shown adhered to bottom edge of the control

box, flush with the front face, and correctly placed along

dishwasher bottom.

Dishwasher Installation

STEP 21: REPLACE TOEKICK

. Placetoekick against the legs of the dishwasher.

Figure CC

Screws

. Align the toekick with the bottom edge and make sure it is

against the floor.

. Insert and tighten the 2 toekick attachment screws. The

toekick should stay in contact with the floor.

. When reinstalling the toe kick on models with a sound barrier,

ensure that the bottom edge isflush with the floor. Any

excess material should be tucked up behind the outer door.

Tip: Reduce sound from under the dishwasher.

Hake sure toekick is against floor.

STEP 22: CHECK THE FOLLOWING

. Tub trim does not interfere with the door

. Dishwasher is square and level at both the top and bottom of

the cabinet opening, with no twisting or distortion of the tub

or door

. All 4 legs of the dishwasher are firmly in contact with the floor

. Drain hose isnot pinched between the dishwasher and

adjacent cabinets or walls

. Tub trim isfully seated on the tub flange

STEP 23: LITERATURE

. Besure to leave complete literature package, these

Installation Instructions and product samples and/or coupons

with the consumer.

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

GEAppliances

General Electric Company

Louisville, Kentucky/40225

GEAppliances.com

Appareils m@nagers

Directivesd'instailation

Lave-vaisselle encastr@

Pourtoute question, composez le 1.800.561.3344 ou visitez notre site Web:

www.electromenagersge.ca

AVANT DE COMMENCER

Veuillez lire attentivement toutes lesdirectives

qui suivent.

A AVERTISSEMENT :

. Pour r_duire lesrisques de choc 61ectrique,d'incendie

ou de blessures, I'installateur doit s'assurer que le lave-

vaisselle est compl_tement encastr6 au moment de

I'installation.

. POURVOTRESECURITEPERSONNELLE:Enlevez le fusible

ou d_clenchez le disjoncteur au panneau de distribution

principal avant de commencer I'installation. N'utilisez pas

une rallonge 61ectrique ou un adaptateur de fiche avec

cet appareil.

Un branchement inad_quat du conducteur de mise 6 la

terre peut pr6senter des risques de choc 61ectrique.Si

vous n'@tespas certain que I'appareil est correctement

mis 6 la terre, consultez un r6parateur ou un 61ectricien

qualifi&

Sile cSblage61ectriquede la r6sidence n'est pasconstitu6

de deux ills plus un fil de mise6 la terre, I'installateur dolt

installer un fil de mise 6 la terre. SilecSblage 61ectriquede

la r6sidenceest en aluminium, utilisezunagent antioxydant

et desconnecteurs pour raccords <<aluminium-cuivre>>

homologu6s UL

A, ATTENTION :

N'enlevez pas la base de bois avant d'@trepr@t6 installer

le lave-vaisselle. Sivous enlevez la base de bois, le lave-

vaisselle pourrait basculer Iorsque vous ouvrez la porte.

POUR VOTRE SI_CURITI_

Veuillez life et observer toutes les raises en gerde

(AVERTISSEMENTet ATTENTION}donn_es dens les pr@sentes

directives. Pour effectuer I'instelletion d_crite dens les pr_sentes

directives, il feut porter des gents et des lunettes de s@curit&

IMPORTANT =Observeztouslescodeset

ordonnances envigueur.

. Note 6 I'installeteur - Veuillez laisser les pr6sentes directives

au consommateur pour I'inspecteur local.

. Note au consommeteur - Veuillez conserver les pr6sentes

directives avec votre Manuel d'utilisation pour consultation

ult@ieure.

. Comp@tences requises - L'installation de ce lave-vaisselle

exige des comp@ences de base en m_canique, en 61ectricit6

et en plomberie. L'instelleteur est responseble de In quelit@

de I'instellation. Toute d@feillance du produit ettribuable

a une installation inadequate n'est pes couverte par la

garantie de GE.Reportez-vous a la gerantie du produit.

. Dur@ede I'installation - Entre i et 3 heures. L'installation

d'un nouveau lave-vaisselle exige plus de temps que

le remplacement d'un ancien module.

IM PORTANT - Lelave-vaisselleDOIT@treinstall6de

mani@e 6 cequ'ilpuisse@tresortide sonemplacement sides

r@parationssontn6cessaires,

IIimported'userde prudencelorsquel'appareilestinstall6

ou d6plac6afinde pr6venirl'endommagementdu cordon

d'alimentation.

Si le lave-vaisselle que vous avez request endommag6,

communiquez imm6diatement avec votre d@aillant ou

I'entrepreneur en construction.

Accessoiresfacultatifs - Reportez-vousau Manueld'utilisationpour

connattrelesensemblespour panneau d6coratifpersonnalis6offerts.

VEUILLEZ LIRE ATTENTIVEMENT

ET CONSERVER CES DIRECTIVES.

,, .... ,, \

'..,._

ImprimdauxEtats-Unis 31-3154£ 09-14 GE

Pr6paration pour I'installation

PIt CESFOURNIES DANS UEMBALLAGE:

. Couverclede la bottedejonction etvis 6 t6te

hexagonalen° 10

. Collier

. Boyaudevid(]nge (198cm/78 po de long)

. Supportde tw(]u devid(]nge)

. 2vis(3t6te hex(]gon(]leno 8-28 pourfixer lessupports

(]uc(]dredeI(]cuvedu I(]ve-v(]isselle

. 2 Boutonsde bouchon

. 2 MouluresI(]t6r(]les(cert(]insmod61es)

. 2supportsde mont(]gepourcomptoirs ou aarmoires

I(]t6r(]lesen bois

. 2vis(3t6te sp6ciaalePhillipsn°8-28 x 25,8mm

(5/8po)pourfixer leI(]ve-v(]isselle(]udessous

du comptoirou (]rmoiresI(]t6r(]les

. Documentaation,6ch(]ntillonset(ou)bans

Couvercle de la

boTte de jonction

et vis 6 t_te

hexogonole n°10

Support de tuyou

de vidange

Vis 6 t_te

hexagonale n° 10

de 12,7 mm {1/2 po)

de long pour boTte

dejonction

(sur certoins modules)

Collier

Vis 6 t@te hexagonole

n° 8 pour support de

montage

Supports de

montage

MATERIEL NI CESSAIRE:

. Coudede 90°(19,1mm [3/4po]filetpour tuy(]ud'(]rros(]ge

dej(]rdin (_uneextr6mit6 et I'(]utreextr6mit6conquepour le

r(]ccordement(_I(]conduite d'(]liment(]tioneneaau)

. Rub(inpourjoints filet6s

. Connecteursvissaableshomologu6sUL(3)

. Rub(]n-caache

Pour une nouvelle installation:

Coude de 90°

Rubon-cache

(s'il y o lieu)

. Coupure(]nti-refoulementpourleboy(]ude vid(]nge,sin_cess(]ire

. RaaccordenTpour I(]plomberiede laar6sidence,slly aalieu

. C_ble61ectriqueoucordon d'aaliment(]tion

. Colliers(_viss(]nsfin

. B(]gue(]nti-tr(]ction pour ler(]ccordement61ectrique _-]

. Robinetd'(]rr6t(recomm(]nd6)

. Conduite d'e(]u chaaude- 9,5 mm (5/8 po) minimum, tuyaau

en cuivre (inclu(]nt I(] b(]gue et 1'6crou(3compression) ou laa

piece W×28×326 de GE,boy(]u m6t(]llique flexible.

. Boy(]ude vidaangede 5,7m(12 pi)de long WD24×10065,si

n6cessaaire Coupure

unti-refoulement

Roccord en T

Boyaudevidange

Boutons de

bouchon

Vis 6 t_te

sp_ciole

Phillips n°8

de 15,8 mm

(5/8 po) de long

Connecteurs

Robinet Ruban pour vissables (3)

d'arr_t joints filet6s

(s'il y a lieu)

C6ble 61ectrique (ou cordon

d'alimentation, s'il y a lieu)

Colliers (] vis sans fin

Conduited'eou

chaude

Bayou de vidange Raccord

focultatif de pour boyau

3,66 m 112pi) de videnge

Bugue anti-traction facultutif

OUTILS NI CESSAIRES:

. TournevisPhillips

. Tourne-6crousde6,3mm (2/4po)et

de 7,9mm (5/16po)

. CI66 molette de 15,2cm (6po)

. Niveaau

. Equerrede ch(]rpentier

. Rubaan(_mesurer

. Lunettesdes_curit6

. L(]mpedepoche

. Se(]upour recueillirI'e(]uIorsdu rinqaage

de I(]conduited'e(]u

. CI_(_douillede 23,8mm (15/16po)

(f(]cult(]tif- pour enleverlaabaasede bois)

, G(]nts

. Pince

, Pour une nouvelle installation:

. Coupe-tubes

. Perceuseetforetsappropri6s

. Jeude scies-cloche

Phillips

CI6 6 douille de

23,8 mm 115/16 pal

Lampe de poche

Gants

Tou

de 6,3 mm (1/4 po)

et de 7,9 mm (5/16 po)

Pince

CI66 molette

de 15,2 cm

16pal

Seau

Niveou

Coupe-tubes

I_querre de

charpentier

Ruban 6 mesurer

Preparation pour l'installation

PRI_PARATION DE L'OUVERTURE DANS

LESARMOIRES

33-1/2 po to 34-3/4 po

du dessous du

comptoir au

plancher

Lemur du fond

doit _tre exempt

de tuyaux ou

de ills

AVERTISSEMENT:

Pourr_duirelesrisquesde choc_lectrique,d'incendieoude

blessures,I'installateurdoits'assurerque lelave-vaisselleest

compl_tementencastr_au momentdeI'installation.

. Lelave-vaisselle doit _tre install6 de faqon 6 ce que le boyau

de vidange mesure au maximum 3.66 m_tres (12 pieds) pour

assurer une vidange ad6quate.

. Ledessus, lesc6t6s et I'arri_re du lave-vaisselle doivent

_tre compl_tement dissimul6s 6 I'int@ieur de I'ouverture.

Lelave-vaisselle ne doit soutenir aucune pattie de la

61,0 cm

(24 po) min.

Figure A

. L'ouverture dans les armoires doit mesurer au mains

61,0 cm (24 po) de largeur et de profondeur, et environ

87,6 cm (34-!/2 po) de hauteur 6 partir du plancher

jusqu'au-dessous du comptoir.

structure des armoires.

DEGAGEMENTS:

. Dans le cas d'une

installation dans un

coin, veuillez pr@oir un

d6gagement d'au mains

5,1 cm (2 po) entre le lave-

vaisselle et lesarmoires, le

mur ou un aectrom6nager

adjacent. Veuillez pr@oir

un d6gagement d'au mains

72 cm (28-:3/8 po)6 I'avant

Armoires c3

1'6querre et

_d'aplomb

du lave-vaisselle pour

I'ouverture de la porte.

Reportez-vous a la

Figure B.

Comptoir

1,2pal

7/ S,1 cm(2 po) minimum pourI'ouverture de la porte

Figure B

E×IGENCES RELATIVES AU SYSTI_ME

DE VIDANGE

. Veuillezobserver lesordonnanceset lescodes Iocauxen vigueur.

. Leboyau de vidange doitavoir uneIongueur maximale de

3.66m_tres (12pieds).

REHARQUE:IIfaut installerune coupure anti-refoulement sile

raccord au broyeura d6chetsou au raccord enTsetrouve a mains

de 46 cm (18po)au-dessusdu plancher afin d'@iter un siphonage.

CHOI× DE LA MI_THODE DE VIDANGE

Letype d'installationde vidange d@end desconditions suivantes.

. Lesordonnances ou codes Iocauxen vigueurexigent-ils

une coupureanti-refoulement?

. Leraccord en Tsetrouve-t-il a mains de 46 cm (18po)

du plancher?

Sivous r_pondez OUI6 I'uneou I'autre de ces questions,

vous DEVEZutiliser la m_thode n° 1.

° Sivousr_pondez NON,vous pouvezemployer I'uneou I'autre

desm@hodes.

PRI'-_-PARATIONDES ARMOIRES

° Percezuntrou de 3,8cm (1-1/2po)de diam_tre dansla paroi de

I'armoirequi setrouve dans la partie ombr6edela FigureApour

leboyau de vidange.Assurez-vousque I'orificene pr6sente pas

d'ar@esvives.

IMPORTANT - Lorsquevous

branchezlebayoudevidange(3un

broyeurc]d6cheis,assurez-vousd'enlever

lebouchondevidange.LELAVE-VAISSELLE

41 nJevezle

bouchon

de vidange

NE POURRA PASSEVIDER SIVOUS LAISSEZLEBOUCHON EN PLACE,

FigureC

M_thode n° 1 - Coupure anti-refoutement avec raccord en T ou

broyeur 6 d_chets

IIfaut installer une coupure anti-refoulement Iorsqu'elle est exig_e par

les ordonnances et les codes Iocaux en vigueur. Cette coupure anti-

refoulement doit @treinstall@econform@ment aux directives donn@es

par le fabricant.

Crochet pour boyau devidange j._g Crochet pour boyau devidonge

Iql / (q_"_ I82cm

III ( fq:tI_S2;_o_

m,n III I Ti

118pal min JJL_ (18po)m_]_

Figure D

M@thode n° 2 - Boucle de vidange @lev@eavec raccord en T ou

broyeur a d@chets

Conseil: Pour @viter des frais de r(_paration inutiles.

Assurez-vous d'enlever le bouchon de vidange du broyeur 6

d6chets avant d'y brancher le boyau de vidange du lave-vaisselle.

Preparation pour I'installation

PRE PARATION DU C#,BLAGE E LECTRIOUE

AVERTISSEMENT:

POURVOTRESECURITEPERSONNELLE:Enlevezlefusibleou

d@clenchezledisjoncteurau panneaude distributionprincipal

avant de commencerI'installation.N'utilisezpasune rallonge

@lectriqueou un adaptateur defiche aveccet appareil.

Alimentation @lectrique

.Cet appareil doit _tre aliment6 par un courant de 120 Vet

60 Hz,et branch6 6 un circuit individuel correctement mis

6 la terre et prot6g_ par un disjoncteur de !5 ou 20 amperes

ou un fusible temporis6.

. Le c@ble61ectrique doit poss6der deux ills, plus un fil de mise

6 la terre, et r6sister 6 une temp@ature nominale de 75 °C

(176 °F).

. Sivotre alimentation 61ectrique ne r6pond pas 6 ces

exigences, appelez un 61ectricien agr66 avant de poursuivre

I'installation.

Mise 6 la terre- Branchement permanent

Cet appareil doit _tre branch6 6 un r6seau _lectrique

permanent mis 6 la terre. Sinon, il faut installer un conducteur

de raise 6 la terre avecles conducteurs du circuit et le brancher

6 la borne de raise 6 la terre du r6seau ou au fil de raise 6 la

terre de I'appareil.

Mise 6 la terre - ModUles dot_s d'un cordon d'alimentation

Cet appareil doit _tre mis 6 la terre. Encas de mauvais

fonctionnement ou de d6faillance, la raise6 la terre r6duira

les risques de choc 61ectrique en fournissant au courant

61ectrique un circuit de moindre r6sistance. Cet appareil est

dot6 d'un cordon d'alimentation poss_dant un conducteur

de raise 6 la terre et une fiche de raise 6 la terre. Lafiche

doit _tre branch6e clans une raise appropri6e, install6e et

raise 6 la terre en conformit6 avec tousles codes Iocaux et

ordonnances en vigueur.

A AVERTISSEMENT:

Un branchement inad_quat du conducteur de raise 6 la terre

peutpr@senterdesrisquesdechoc@lectrique.Sivousn'@tespas

certain que I'appareilestcorrectementmis6 laterre,consultez

unr@parateurouun @lectricienqualifi@.

u -- E

z IAutreemplacement ?\

I possiblepourla prise i \

i de courant dans une i \

I armoire ac \

46 cm (18 po)

-- 46 cm i÷ laprise d_--_l

(18po) I cou@,tIS1

/1÷'-

15cm 16po) 15cm-_

7,6cm (3po)

des armoires

Mise 6 la terre

Noir

Figure E Blanc

Dons le cos des modules dot_s d'un cordon d'alimentotion:

Ne modifiez pas la fiche fournie avec I'appareil; si vous ne

pouvez pas la brancher dans la prise de courant, faites installer

une prise de courant appropri6e par un technicien qualifi6.

Preparation des ormoires et cheminement des ills

Lesills peuvent entrer dans I'ouverture du c6t_ droit, du c6t_

gauche, de I'arri@e ou du plancher dans la pattie ombr6e de

la Figure Eet de la FigureA.

Percez un trou de 3,8 cm (1-1/2 po) de diam_tre au maximum

pour le passage du cable 61ectrique.Le bard du trou doit

_tre lisse et arrondi. Lesills 61ectriques pour le branchement

permanent peuvent passer par le m_me trou que le boyau

de vidange et la conduite d'eau chaude, si c'est plus pratique.

Si le trou est pratiqu6 dans une paroi en m@al, les bards de

I'orifice doivent _tre recouverts d'un passe-fils pour prot6ger

les fils.

REMARQUE:Lecordon d'alimentation dot6 d'une fiche doit

passer par un autre trou.

Branchement _lectrique du lave-voisselle

Le branchement _lectrique s'effectue du c6t_ avant droit du

lave-vaisselle.

Dans lecas d'un branchement permanent, le c_ble doit _tre

achemin_ de la faqon indiqu_e 6 la Figure E.Lec_ble doit

avoir une Iongueur minimale de 61 cm (24 po)6 partir du tour

arri@e.

Dans lecas d'un branchement avec un cordon d'alimentation,

installez une prise de courant raise 6 la terre 6 trois broches

sur la paroi de I'armoire adjacente, entre 15 cm (6 po) et

46 cm (18 po) de I'ouverture, et entre 15 cm (6 po) et 46 cm

(18 po) du plancher.

Utilisez uniquement W×09×70910 ou W×09×70911 Trousse

de cordon d'alimentation pour lave-vaisselle.

Page is loading ...

GE GDT550HGD4WW Installation guide

Brand: GE

Model: GDT550HGD4WW

Category: Dishwashers

Type: Installation guide

This manual is also suitable for

Download PDF

report

in other languages

français: GE GDT550HGD4WW Guide d'installation

GE GDT550HGD4WW Installation guide

This manual is also suitable for

GE GDT550HGD4WW Installation guide

in other languages

Related papers

Other documents