Monte Carlo Fan Company 5SLR52 User manual

Brand: Monte Carlo Fan Company

Model: 5SLR52

Category: Household fans

Type: User manual

This manual is also suitable for

5SLR52 Series

QUALITY CEILING FANS

OWNER’S

MANUAL

Ceiling Fan Installation Instructions

Total fan weight

with light

READ AND SAVE THESE INSTRUCTIONS

For 5SLR52 Series Fans

emove keeper from pin and pin

from downrod. Place k

eeper back on

pin and sa

ve for later.

Loosen the 2 set screws till you can

not feel them on inside of yoke.

Thead leadwires and safety cable

through downrod. (as shown)

Before you begin installing the fan, Switch

power off at Service panel and lock service dis-

connecting means to prevent power from being

switched on accidentally. When the service dis-

connecting means cannot be locked, securely

fasten a prominent warning device, such as a

tag, to the service panel.

Before installing this fan make sure the outlet box is

properly installed to the house structure. To reduce

the risk of fire, electric shock, or personal injury

mount to outlet box or supporting system acceptable

for fan support. (Mounting must support at least 35

lbs.)

Use metal outlet box suitable for fan support

(must support 35 lbs). Before attaching fan to

outlet bo

x, ensure the outlet bo

x is securley

fastened by at least two points to a structur

ceiling member ( a loose box will cause the fan

to w

abble).

Use only the screws provided

with the outlet box.

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes ANSI/NFPA 70-1999),

including fire-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding con-

ductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box.

Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from

being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device,

such as a tag, to the service panel.

Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7

feet from the floor to the trailing edge of the blade.

To reduce the risk of fire, electric shock, or personal injury, mount to outlet box or supporting system acceptable for fan support.

Use only the screws provided with the outlet box. (Mounting must support at least 35 lbs.)

Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating

blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING - To reduce the risk of fire or electric shock, this fan should be used with fan speed control part no. UC7067RC-L, manufac-

tured by Rhine Electronic Co., Ltd.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heat-

ing equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA),

and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being

switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such

as a tag, to the service panel.

WARNING - To reduce the risk of electric shock, this fan must be installed with an isolating wall contorl,switch.

WARNING - All set screws must be checked and retightened where necessary before installation.

10.

11.

12.

13.

14.

15.

ARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS

FETY

TOOLS REQUIRED

Phillips Screwdriver Wire Cutters Pliers Step Ladder

Installation

Hang assembled fan from the mounting brack

installed to ceiling in previous step. Make sure

the fan is hanging str

aight. R

otate fan until the

tab on the Mounting br

ack

et engages the slot

on the Downrod Ball. This must be done to

ent the fan body from rotating when the

blades are in motion.

Make sure the studs protruding from the

bottom of the Mounting bracket are

installed with threads all the way through

the bracket.

Place downrod into fan yoke.

Install the keeper to pin.

Tighten the 2 set screws on the yoke

once the downrod is in place.

Align the hole in the downrod with

the hole in the yoke. Insert th pin

through the yoke and downrod until

the point appears on the other side.

Thread leadwires and safety cable

through downrod. (as shown)

Place yoke cover on downrod. (as

shown)

Pull down y

oke co

ver.

Install remote receiv

er into mounting

ack

et.

Set dip switches on the Remote Transmitter and

Remote Receiver to the same settings. This must be

done so the units will communicate properly

. If y

have other fans you can set to control from one trans-

mitter by setting both receivers the same as the

transmitter. If you have more than one fan with

remote. Y

ou can set the dip switches to different posi

tions to have seperate control.

emote T

ansmitter

Dip switches

emote Receiver Dip

switches

Fan and light kit combinations over 35 lbs,

in both flush and downrod mode the safety

cable must be installed into the house struc

ture beams using the 3” lag screws,washers,

and lock washers. provided. Make sure that

when the safety cable is fully extended the

lead wires are longer than the cable and no

stress is placed on the lead wires.

Safety cable installation

Safety Cable

Lag Screw

afety

cable

3” lag

screw

lock

washer

ttach glass b

y locating dimples in

light kit with the gro

ves in glass and

twist clockwise till tight.

Connect plug from fan to switch

house plug. (as shown)

Make wiring connections for remote

receiver to fan as above diagram.

Carefully snap flurescent lamp into

clips.

Attach blades to motor using screws

and washers in hardware bag and

tighten screws securely.

Loosen 2 screws and remove 1 screw

from motor plate. Save removed

screw for use later.

Install light plate with ballast to fan

y twisting plate with k

ey hole slots

into place. Replace screw removed

and tighten the 3 screws securely.

Plug ballast into the flourescent

lamp

Ready for wiring

Lift canopy and install knurled nuts as

shown. Tighten the knurled nuts securely.

The canopy should adjust for any irregu-

larity in the ceiling or Outlet box.

Make wire connections to power source using

wire nuts prov

ided. Make sure that no filiments

are outside of the wirenut. After making the

wire connections, the wires should be spread

apart with the grounded conductor and the

equipment-grounding conductor on one side of

the outlet box and ungrounded conductor on

the other side of the outlet box.

onnect black from remote receiver to black or

(

hot) wire from house. Connect white wire from

emote receiver to white (neutral) wire from

ouse. Connect green ground leads from

mounting bracket and downrod to ground lead

from house. Refer to Safety Tips section of

manual.

Attach front cover to wall control

with screws provided.

Install wall control unit to outlet box

using machine screws provided.

Remove cover by snapping off from top or

bottom. Install 12V battery into wall

remote. Duracell MN21 / Eveready A23 /

P 23A.

Attach cover of remote by placing

over buttons and snapping into

place.

To control fan speed select from High,

Medium or Low speed buttons. To turn the

fan off press the fan on / off button. To

dim lights press and hold button. To turn

off light press and quickly release button.

Press button marked REV to reverse the

rotation direction of the fan blades with fan

on low or med.

Fan speed control

buttons

Fan on / off

Light dimmer for

lights

Fan reverse button

Customer Service Center:

740 S.W. Loop 820, Suite 110

Fort Worth, Texas 76115

1-800-519-4092

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

CAUTION: Make sure main power is turned off.

3.Make sure forward/reverse switch is firmly in up or down position. Fan will not operate when

switch is in the middle.

1.Check to make sure all screws in motor housing are snug (not over tightened).

.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each other or

against the interior wall of the switch housing.

CAUTION: Make sure main power is turned off before entering switch housing.

4.If using an optional Ceiling Fan Light Kit, check to be sure the screws securing the glassware are

finger tight. Check to be sure light bulb is tight in socket and not touching glass shade(s). If vibra-

tion persists from glass, remove glass and install a 1/4" wide rubber band on glass neck to act as

an insulator. Replace glass and tighten screws against rubber band.

5.Some fan motors are sensitive to signals from Solid State variable speed controls.

DO NOT USE

a Solid State variable speed control.

6.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear after

this period.

1.Make sure that the ridge of the canopy engages the notch in the downrod ball. (See illustration in

Step #6 of Downrod Mount installation).

2.Check that all blades are screwed firmly into blade holders.

3.Check that all blade holders are tightened securely to motor.

4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box and

junction box is mounted firmly to ceiling joist.

5.Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting

a point on the ceiling abo

ve the tip of one of the blades. Measure this distance from blade tip to

ceilng. Keeping measure within 1/8", rotate the fan until the next blade is positioned for measure-

ment. Repeat for each blade. If all blade levels are not equal, you can adjust blade levels by the fol-

lowing procedure. To adjust a blade tip down, insert a washer (not supplied) between the blade and

blade holder at the screw closest to the motor. To adjust a blade tip up, insert washer (not supplied)

between the blade and blade holder at the two screws farthest from the motor. Reverse the posi-

tion of the washer if blades mount from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side b

y side) blades can redistrib

ute the weight and possibly result in smoother operation.

1.Check blue wire from fan to mak

e sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for fault

y light bulbs.

CAUTION: Make sure main power is turned off before entering switch housing.

2. If fan sounds noisy:

. If fan does not start:

3. If fan wobbles:

4. If light does not work:

TROUBLE SHOOTING

f you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In

some cases, these installation errors may be mistaken for defects. If you experience any faults, please check this Trouble

hooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installation, please call our

Customer Service Center at the

number printed on your parts list insert sheet.

Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

eans to prevent power from being switched on accidentally. When the service disconnecting means cannot

be locked, securely fasten a

rominent warning device, such as a tag, to the service panel.

Monte Carlo Fan Company 5SLR52 User manual

Brand: Monte Carlo Fan Company

Model: 5SLR52

Category: Household fans

Type: User manual

This manual is also suitable for

5SLR52 Series

Download PDF

report

Monte Carlo Fan Company 5SLR52 User manual

This manual is also suitable for

Monte Carlo Fan Company 5SLR52 User manual

Related papers

Other documents