BLADEZ MOBY XS PB-SE823 Product Handbook

Brand: BLADEZ

Model: MOBY XS PB-SE823

Category: Scooters

Type: Product Handbook

This manual is also suitable for

Bladez Corp. • 20155 Ellipse • Foothill Ranch, CA 92610 • (866) 325-2339 • www.ebladez.com

Page 0

Product Handbook

FOR THE BLADEZ MOBY XS

GAS POWER BOARD

Models: PB-SE823

PB-SE825

PB-SE825PF

PB-SE826

PB-SE830PF

PLEASE BE SAFE WHEN RIDING

ALWAYS WEAR A HELMET AND OBEY ALL LAWS!

Powered Personal Transportation

GAS POWER BOARD

Bladez Corp. • 20155 Ellipse • Foothill Ranch, CA 92610 • (866) 325-2339 • www.ebladez.com

Page 1

IMPORTANT

THIS IS A 2-CYCLE ENGINE

IT REQUIRES A MIXTURE OF GAS AND 2-STROKE

ENGINE OIL

1. You must

always use a gas oil mixture. FAILURE TO DO SO

WILL VOID YOUR WARRANTY!

2. Use 50:1 Gas / Oil Mixture. 2.6 oz of oil for every gallon of High-

Octane Gasoline.

3. Tanaka Perfect Mix or similar high quality 2-Cycle Engine Oil

recommended. Oil can be purchased from your local Bladez

Dealer, Outdoor Power Equipment Dealer, Power Sports Dealer or

on the web at www.ebladez.com

4. High-Octane Fuel Recommended. (90 octane or higher)

Failure to follow these INSTRUCTIONS will

VOID YOUR WARRANTY!

This PRODUCT IS NOT

INTENDED FOR EXTREME or

OFF-ROAD Use! Please take care of your POWER BOARD!

DO NOT JUMP or ABUSE THIS PRODUCT!

DO NOT RIDE IN WET/ICY CONDITIONS!

Failure to follow these instructions will

VOID YOUR WARRANTY!

If you have any questions, please contact Bladez customer service

(866) 325-2339 or visit us on the web at www.ebladez.com

Bladez Corp. • 20155 Ellipse • Foothill Ranch, CA 92610 • (866) 325-2339 • www.ebladez.com

Page 2

IMPORTANT

PLEASE READ THIS BEFORE USING THIS PRODUCT

READ THIS FIRST!

WARNING

This product does not conform to Federal Motor Vehicle Standards and is not

intended for operation on public streets, roads or highways. Serious injury can

result from the unsafe operations of this product. Operator can minimize these

risks by using certain safety equipment such as: safety helmet, goggles,

gloves, elbow and kneepads and appropriate footwear.

DO NOT operate this product in traffic, on wet, frozen, oily or unpaved

surfaces or under the influence of drugs and/or alcohol. Avoid uneven

surfaces, potholes, surface cracks and obstacles.

DO NOT use a water hose to clean this product. See Product Handbook for

more information.

This product is recommended for riders 16 YEARS OF AGE and older.

SAFETY

 This product should not be used by persons without excellent vision,

balance, coordination, reflex, muscle and bone strength and good

decision-making capabilities.

 This product should not be used by minors without adult supervision.

 This product should not be used by persons unwilling or unable to take

responsibility for their own actions.

 The user of this product assumes ALL risks associated with its use. To

minimize these RISKS, the user must wear safety helmet, goggles, gloves,

elbow and knee pads and appropriate footwear.

 Never start the engine inside a closed room or building. Breathing exhaust

fumes can be fatal.

Bladez Corp. • 20155 Ellipse • Foothill Ranch, CA 92610 • (866) 325-2339 • www.ebladez.com

Page 3

IF YOU HAVE ANY QUESTIONS OR NEED

ASSISTANCE,

PLEASE CALL BLADEZ, TOLL FREE AT:

(866) EBLADEZ

(866) 325-2339

MONDAY thru FRIDAY, 8am to 5pm PST

or visit us on the web at:

www.ebladez.com

GROWING NETWORK OF SERVICING DEALERS

FOR ALL YOUR POWER BOARD NEEDS

DO NOT TAKE YOUR

BLADEZ POWER BOARD BACK

TO THE STORE!

Bladez Corp. • 20155 Ellipse • Foothill Ranch, CA 92610 • (866) 325-2339 • www.ebladez.com

Page 4

Fuel Safety

 Mix and pour fuel outdoors away from sparks or flames.

 Only use a container approved for fuel.

 Smoking is prohibited near the Power Board while working on the engine, or

while the engine is running.

 Wipe up and clean all fuel spills before starting the engine.

 Move at least 10 feet away from your fuel station before starting engine.

 Stop engine before removing the fuel cap.

 It is recommended that you empty the fuel tank prior to shipping or storage to

prevent fuel leaks.

 Do not store your Power Board near open flames, furnaces, electric motors or

switches.

Maintenance

 Maintain your Power Board as recommended in this Product Handbook.

 Disconnect the spark plug cap before performing any engine maintenance,

except for carburetor adjustments.

 Keep others away while making carburetor adjustments.

 Use only quality replacement parts as recommended by the manufacturer.

Transportation and Storage

 Carry your Power Board by the handlebar tube with the engine off and the

muffler away from your body.

 Allow the engine to cool, empty the fuel tank and fold the Power Board before

carrying or storage.

 It is necessary for you to empty the fuel tank prior to shipping or storage to

prevent fuel leaks.

 Clean the Power Board carefully and store in a cool, dry place.

Product Safety

 Keep hands and feet away from moving parts.

 Inspect the entire product prior to each use. Replace damaged parts. Check

for fuel leaks and make sure all fasteners are in place and securely fastened.

 Replace all parts that are cracked, chipped or damaged before use.

 Use only parts and accessories that are recommended by the manufacturer.

If a situation arises that is not covered in the manual,

proceed with caution and use good judgment.

Contact your dealer or Bladez (

www.ebladez.com)

if you need further assistance

QUICK REFERENCE

SAFETY GUIDE

Bladez Corp. • 20155 Ellipse • Foothill Ranch, CA 92610 • (866) 325-2339 • www.ebladez.com

Page 5

TABLE OF CONTENTS

GETTING TO KNOW YOUR BLADEZ POWER BOARD...........................................6

PACKAGE CONTENTS...............................................................................................7

GETTING STARTED ...................................................................................................7

Unfolding................................................................................................................................ 7

Attaching The Handlebars .................................................................................................... 7

Fueling.................................................................................................................................... 8

Starting................................................................................................................................... 8

Riding ..................................................................................................................................... 9

Braking................................................................................................................................... 9

FOLDING AND STORAGE .........................................................................................9

OPERATING PROCEDURES ...................................................................................10

Fuel....................................................................................................................................... 10

Fueling.................................................................................................................................. 10

Starting................................................................................................................................. 10

Stopping............................................................................................................................... 10

MAINTENANCE.........................................................................................................11

Recommended Tools .......................................................................................................... 11

Carburator Adjustment ....................................................................................................... 11

Idle Speed Adjustment........................................................................................................ 11

Tires And Wheels ................................................................................................................12

Chain Adjustment................................................................................................................12

MAINTENANCE SCHEDULE....................................................................................13

OTHER QUESTIONS.................................................................................................13

Bladez Corp. • 20155 Ellipse • Foothill Ranch, CA 92610 • (866) 325-2339 • www.ebladez.com

Page 6

GETTING TO KNOW YOUR BLADEZ POWER BOARD

Before operating your BLADEZ Power Board, please get acquainted with all of the

features.

Power Board Features

1. Throttle Lever 8. Engine

2. Handlebar Tube 9. Billet Handlebar Stem

3. Front Forks 10. Brake Lever

4. Front Brakes 11. Kill Switch

5. Kick Stand 12. Handlebar Hook

6. Folding Handle 13. Rear Sprocket

7. Wood Deck 14. Rear Axle Tension Screw

15. Foot Brake

Bladez Corp. • 20155 Ellipse • Foothill Ranch, CA 92610 • (866) 325-2339 • www.ebladez.com

Page 7

PACKAGE CONTENTS

Your Bladez MOBY XS comes with the following items in the box. Please locate all

of the following:

1. The Bladez MOBY XS Power Board

2. Allen Wrench

3. Spark Plug wrench

4. Product Handbook

GETTING STARTED

Please read and understand these instructions and the OPERATING

PROCEDURES section, prior to starting or riding your Power Board.

Unfolding

1. Carefully remove the MOBY XS from the

box.

2. To unfold the MOBY XS, begin by

pulling up on the FOLDING HANDLE

with one hand (Fig. 1), while gently

pulling up on the handlebars with the

other.

3. Fully extend the handlebars to their

upright position until you feel the

mechanism lock into place. (Fig.2)

Attaching The Handlebars

1. When you take the MOBY XS out of the box,

you will need to attach the handlebar to the

scooter. Remove the billet stem cap using

the Allen wrench provided. Place the

handlebar into the groove by lining up the

hole with the screw in the billet stem. (Fig. 3)

2. Replace the billet stem cap and tighten down

the bolts to secure the handlebar. (Fig. 4)

Bladez Corp. • 20155 Ellipse • Foothill Ranch, CA 92610 • (866) 325-2339 • www.ebladez.com

Page 8

Fueling

This is a two-stroke engine. Only run the engine using a mixture of gasoline

and 2-cycle engine oil.

PLEASE READ OPERATING PROCEDURES BEFORE FUELING!

1. Mix fuel (minimum 90 octane) and 2-cycle engine oil in a separate container. Use

high quality 50:1 2-cycle oil. 2.6 oz of oil for every gallon of High-Octane Gasoline.

Make sure the fuel is well mixed by shaking the container.

2. Make sure that the engine is off!

3. Slowly open the GAS CAP, so that possible over-pressure disappears.

4. Clean the tank cap area to make sure that it is free from excess dirt and debris.

* Make sure that no dirt falls into the gas tank.

5. Pour pre-mixed Gas/Oil mixture into the GAS TANK. * Do not overfill.

6. After fueling, replace the GAS CAP and tighten.

Starting

Move at least 10 feet away from where

you fill up with gas.

1. Depress clear, plastic primer bulb (on

carburetor), several times briskly until it

fills with fuel.

2. Set the CHOKE LEVER to the CHOKED

(UP) position. (Fig. 5)

3. Pull the RECOIL STARTER briskly,

making sure to hold the handle in your

grasp. (Fig. 6) * Note: Do not allow it to

snap back, let it back slowly. You may

want to give it a little throttle by gently

squeezing the GAS LEVER.

4. It may be necessary to repeat step 3

several times until the motor starts.

When starting the MOBY XS for the first

time, it may be necessary to pull the

starter handle multiple times until it

starts.

*This is because the gas needs to be drawn

into the carburetor.

5. Once the engine has started, quickly

move the CHOKE LEVER into the RUN

(DOWN) position. (Fig. 5)

6. After the engine is started, let it warm up

for 2-3 minutes before riding.

Bladez Corp. • 20155 Ellipse • Foothill Ranch, CA 92610 • (866) 325-2339 • www.ebladez.com

Page 9

IF THE MOTOR KEEPS STALLING AT

IDLE SPEED, IT MAY BE NECESSARY

TO ADJUST THE IDLE SPEED ON THE

CARBURETOR. (Fig. 7)

Please refer to Carburetor Adjustment

in the

Maintenance section on page 11 for

instructions on how to adjust idle speed.

Riding

1. Make sure that all of the exposed bolts

and screws are tightened.

2. Raise the kickstand to its upright

position.

3. Make sure the engine is running.

4. Put one foot on the deck of the MOBY

XS. While pushing off with the other foot,

gently depress the THROTTLE LEVER,

on the right side of the handlebars. The

MOBY XS will begin to move on its own

power.

5. Control your speed by pressing and

releasing the accelerator lever. The

harder you squeeze, the faster you will

go.

Braking

1. To brake, release the THROTTLE

LEVER and depress the BRAKE LEVER

(on the left side of the handlebars). You

can also use the rear foot brake. (Fig. 8)

2. Gradually decrease the engine speed to

idle and press the kill switch button on

the handlebar tube. (Fig. 9) This will turn

the engine OFF.

FOLDING AND STORAGE

When you are done riding the MOBY XS you can fold it down for compact storage,

carrying and transportation. To fold down the MOBY XS, use one hand to pull up on

the folding handle while gently pulling down on the handlebars. BE CAREFUL NOT

TO HIT YOUR HEAD WITH THE HANDLEBAR. Use the hook to secure the

handlebars when in the folded position. You can now carry the MOBY XS by the

handlebar tube.

Bladez Corp. • 20155 Ellipse • Foothill Ranch, CA 92610 • (866) 325-2339 • www.ebladez.com

Page 10

OPERATING PROCEDURES

Fuel

WARNING!

This is a two-stroke engine. Only run the engine on fuel, which is properly

mixed with 2-cycle engine oil.

Provide good ventilation when fueling or handling fuel.

 Always use gas with a minimum octane number of 90.

 Use 2-stroke engine oil only. Mix 50:1 gas / oil mixture.

 Never use multi-grade (10W/30) or waste oil.

 Always mix fuel and oil in a separate clean, gas safe container. Always

start by adding half the amount of fuel which is to be used. Then add the

whole amount of 2-cycle oil. Mix (shake) the fuel container. Add the

remaining amount of fuel. Mix (shake) the fuel-oil thoroughly before filling

the fuel tank.

Fueling

WARNING!

 Always shut the engine off before you refuel.

 Slowly open the fuel tank, so that possible over-pressure disappears.

 Before fueling, clean the tank cap area carefully, to insure that no dirt falls

into the tank. Make sure that the fuel is well mixed by shaking the

container.

 Tighten the fuel cap carefully, after fueling.

 Always move the unit at least 10 feet from the fueling area before starting.

Starting

 Set the CHOKE LEVER to the CLOSED (UP) position.

 Pull the recoil starter handle briskly, making sure to keep the handle in

your grasp, and not allowing it to snap back.

 Once the engine is running, move the CHOKE LEVER to the RUN

(DOWN) position.

Note!

At this stage, if the engine does not start, repeat the starting procedure.

 After starting the engine, allow the engine 2-3 minutes to warm up prior to

riding.

Stopping

 Gradually decrease the engine speed to an idle speed and press the kill-

switch on the handlebar tube.

Bladez Corp. • 20155 Ellipse • Foothill Ranch, CA 92610 • (866) 325-2339 • www.ebladez.com

Page 11

MAINTENANCE

Recommended Tools

To adjust and service the Bladez MOBY XS Power Board you will need the following

tools:

 Allen Wrenches: 3 / 4 / 5 / 6 mm.

 Wrenches: 10 / 13 / 16 mm open and ring combination.

 Short reach Spark Plug Socket

 Large Adjustable Crescent Wrench

 Spark Plug Sockets

 Philips Head Screwdrivers

 Oil, Grease or Lubricant (such as WD-40)

Carburetor Adjustment

WARNING!

Never start the engine without the complete clutch cover assembled!

Otherwise the clutch can come loose and cause personal injuries.

In the carburetor, fuel is mixed with air. When the engine is test run at

the factory, the carburetor is basically adjusted. A further adjustment

may be required from time to time, depending on climate and altitude.

The carburetor has only one possible adjustment:

T= idle speed adjustment screw

Idle Speed Adjustment

When the idle speed is adjusted properly, the engine will run smoothly,

without pressing the THROTTLE LEVER. (Fig. 10)

If Adjustment Is Required:

1. Start the engine.

2. Using a long, Philips head screwdriver

gently close (clockwise) the T-screw

until the MOBY XS starts to move

forward.

3. Then open (counter-clockwise) the

screw until the MOBY XS stops.

4. You have reached the correct idle speed

when the engine runs smoothly below

the RPM when the MOBY XS starts to

move.

Note: Standard idle RPM is about 2500-

3000 RPM.

Bladez Corp. • 20155 Ellipse • Foothill Ranch, CA 92610 • (866) 325-2339 • www.ebladez.com

Page 12

WARNING!

When the engine is idling, under no circumstances should your MOBY

XS be moving.

If the MOBY XS continues to move after idle speed adjustment, contact

Bladez or your local Bladez service center.

Tires And Wheels

The Bladez MOBY XS uses an identical rim and tire assembly on the front and rear

wheel, which means that the tires can be rotated. The wheels are actually two wheel

halves (split rim) bolted together to make it easier to remove and replace the tire and

tube.

Tire wear will differ based on rider weight, riding conditions and care. Replacement

tires can be obtained at your local Bladez dealer, through motorcycle shops, or from

the Bladez website at www.ebladez.com

Tire Pressure

The tire must be inflated to a maximum of 60 P.S.I. It is also recommended to

use a tube additive like Slime

available from any motorcycle shop, to avoid

inconvenient punctures.

WARNING!

Empty all air from the tire

, prior to loosening the bolt to split the rim.

Chain Adjustment

The chain will come adjusted from the factory. However, it may be necessary to

adjust the chain from time to time.

How Tight Should The Chain Be?

 If the chain is skipping or jumping on the sprocket teeth, it is too loose and

should be adjusted.

 The chain should be tight enough not to skip, but have a little bit of play.

Adjusting The Chain

1. Loosen the rear axle bolt but do not

remove the axle.

2. Tighten or loosen the rear axle tension

screws until you find the proper chain

tension. (Fig. 11) (About 1/8 of an inch

of play will be the proper tension for your

chain)

Bladez Corp. • 20155 Ellipse • Foothill Ranch, CA 92610 • (866) 325-2339 • www.ebladez.com

Page 13

MAINTENANCE SCHEDULE

Proper care of your Power Board will insure optimal performance and longer life

span. The following are a few maintenance suggestions that will keep your Power

Board running in top condition:

Daily Maintenance

Perform each time you ride your MOBY XS.

 Clean the exterior of the unit with a soft, damp rag.

 Check that all nuts and bolts are securely tightened.

Weekly/Monthly Maintenance

 Check the starter, especially the cord and return spring.

 Remove the spark plug and check the electrode gap. Adjust it to .024”, or

change the spark plug.

 Clean the cooling fins on the cylinder head and check that the air intake at

the starter is not clogged.

 Clean the air filter.

BLADEZ MOBY XS PB-SE823 Product Handbook

Brand: BLADEZ

Model: MOBY XS PB-SE823

Category: Scooters

Type: Product Handbook

This manual is also suitable for

Download PDF

report

BLADEZ MOBY XS PB-SE823 Product Handbook

This manual is also suitable for

BLADEZ MOBY XS PB-SE823 Product Handbook

Related papers

Other documents