SunBrite SB-P2-32-1K-BL Owner's manual

Brand: SunBrite

Model: SB-P2-32-1K-BL

Category: LCD TVs

Type: Owner's manual

This manual is also suitable for

Operator’s Manual

Revision 20200604_0800

PN: MSP-002-00

Pro 2 Series 1K/4K

Model SB-P2-32-1K

SB-P2-43-1K

SB-P2-49-4K

SB-P2-55-4K

SB-P2-65-4K

Page 2

For California, Connecticut, Hawaii, Illinois, Indiana, Maine, Maryland, Michigan, Minnesota,

Missouri, North Carolina, New Jersey, New York, Oklahoma, Oregon, Pennsylvania, Rhode Island,

South Carolina, Texas, Utah, Virginia, Vermont, Washington, Washington D.C., Wisconsin, and

West Virginia Consumers Only:

For the recycling of SunBrite brand TV’s and other brand TV’s, please contact customer service at 866-357-8688 for details.

SunBrite does not charge a separate fee at the time of recycling and provides free shipping and free containers as part of

our recycling mailback program.

If you are mistakenly billed by the shipping company for any services or fees on your recycling request, please contact

customer service at 866-357-8688.

Recycling Programs

SnapAV remote management

• Remote Firmware Updates

OvrC noties and provides integrators with the newest software updates when available, so they can solve problems

and upgrade devices remotely.

CA Prop65 Warning

Page 2

Dear SunBriteTV Customer:

Congratulations on the ownership of your SunBriteTV all-weather outdoor LCD TV, and welcome to the family of satised SunBrite customers. You are in great company,

with thousands of homeowners and esteemed commercial facilities such as Yankee Stadium, Fenway Park, Disney World, and Sea World who have trusted us to deliver

superior performance, lasting durability and the enjoyment of superb television viewing in the great outdoors.

Our products are designed to withstand the rigors of the outdoor environment and provide our customers with many years of optimum viewing, while delivering

excellent picture and sound as well as the ease of use and convenience of conventional indoor TVs.

To ensure safety and long product life, please read the Important Safety Instructions and complete manual carefully before using the TV. If you have any questions about

the installation procedures, please contact our qualied SunBriteTV Customer Support Team at 866-357-8688.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: TV must be plugged into a GFCI receptacle. the rated residual operating current shall not exceed

30mA. TV and GFCI RECEPTACLE MUST BE INSTALLED NO LESS THAN 5 FEET FROM ANY BODY OF WATER

(SUCH AS POOL OR SPA). Check local building codes for proper installation guidelines.

This product utilizes tin-lead solder.. Disposal of these materials may be regulated due to environmental considerations. For

disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www.eia.org.

WARNING: This unit is equipped with a 3-pin grounded plug. The plug will only t into a grounded power outlet. This is a safety feature. If you

are unable to insert the plug into the outlet, contact your electrician. Do not alter this plug, as this will defeat the safety feature.

CAUTION: THE POWER SUPPLY CORD IS USED AS THE MAIN DISCONNECT DEVICE, ENSURE THAT THE SOCKET-OUTLET IS LOCATED/INSTALLED

NEAR THE EQUIPMENT AND IS EASILY ACCESSIBLE

WARNING: This product shall be connected to a mains socket outlet with a protective earthing connection.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

WARNING: FCC Regulations state that any unauthorized changes or modications to this equipment not expressly approved by the manufac-

turer could void the user’s authority to operate this equipment.

NOTE TO CATV SYSTEM INSTALLER: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National

Electrical Code that provides guidelines for proper grounding and, in particular, species that the cable ground shall be connected to the

grounding system of the building, as close to the point of cable entry as practical.

WARNING: To reduce the risk of re or electric shock, do not expose the inside of this apparatus to rain or moisture.

Important Safety Instructions

1) Read these instructions, and keep them for future use.

2) Heed all warnings and follow all instructions.

3) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

4) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers) that

produce heat.

5) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for

your safety. If the provided plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet.

6) Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where

the cord exits from the apparatus.

7) Only use attachments/accessories specied by the manufacturer.

8) Use only the cart, stand, tripod, bracket or table specied by the manufacturer, or

sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

9) Unplug this apparatus during lightning storms.

10) Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, does not operate

normally, or has been dropped.

Disclaimer: While SunBriteTV LLC intends to make this manual accurate and complete, we do not make claims that the information

contained within covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the

installation or use of this product. The information contained in this manual may change without notice.

SunBriteTV Pro 2 Series Operator’s Manual

Page 3

Cleaning Instructions: See “Care of SunBriteTV” on page 39.

Attachments: Do not use attachments not specically recommended by the manufacturer. Use of improper attachments can

result in accidents.

Power Source: SunBriteTV must operate on a power source indicated on the specication label. If you are not sure of the type of

power supply used in your home, consult your dealer or local power company. When using the TV outdoors, you must use a GFI-

protected AC outlet with “in-use” waterproof cover, the rated residual operating current shall not exceed 30mA.

Installation: Do not place the product on an unstable cart, stand, tripod, table, or anywhere the unit is not permanently installed.

Placing the product on an unstable place can cause the product to fall, resulting in potential serious personal injuries, as well as

damage to the product.

Precautions when Transporting the TV: Carrying the television requires at least two people.

FCC Statement

This equipment complies with the limits for

a Class B digital device, pursuant to part 15

of the FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used

in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference

to radio or television reception, which can be

determined by turning the equipment o and

on, the user is encouraged to try to correct the

interference by one or more of the following

measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment

and receiver.

3. Connect the equipment into an outlet on a

circuit dierent from that to which the receiver is

connected.

4. Consult the dealer or an experienced radio/TV

technician for help.

Modications not expressly approved by the

manufacturer could void the user’s authority

to operate the equipment under FCC rules.

This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference

received, including interference that may cause

undesired operation.

Important Safety Instructions

Page 4

Ventilation: Adequate ventilation must be maintained to ensure reliable and continued operation and to protect the

television from overheating. There must be at least 1.5” of space on all sides.

Power cord protection: The power cord must be routed properly to prevent people from stepping on it, or objects

from resting on it. Check the cords at the plugs and product.

Power source: This product must operate on a power source specied on the specication label. If you are unsure of

the type of power supply used in your home, consult your dealer or local power company.

Do not let metal pieces or objects of any kind fall into the television from ventilation holes. High voltage ows in the

product, and inserting an object can cause electric shock and/or short internal parts.

Do not mount SunBriteTV near a motor or transformer where strong magnetism is generated. Images on the

television will become distorted and the color irregular.

Do not mount SunBriteTV near heat sources such as radiators, heaters, stoves and other heat-generating products

(including ampliers).

Do not submerge SunBriteTV in water: The SunBriteTV will resist water exposure from normal rain, sprinklers,

garden hoses, etc.; however, it is not designed to be submerged in water.

Do not pressure-wash SunBriteTV: SunBriteTV will resist water exposure from normal rain, sprinklers, garden hoses,

etc.; However, it is not designed to withstand pressure washers, high-pressure water jets, or hurricane-type weather.

Do not service SunBriteTV yourself: Removal of the television screen cover may expose you to high voltage or other

dangerous risks. Refer all servicing to a qualied service professional. Warranty will not be honored if you service the

unit yourself.

Repair: If any of the following conditions occurs, unplug the power cord, and call a qualied service professional to

perform repairs:

When power cord or plug is damaged.

When objects have fallen into the product.

If unit was submerged in water or pressure-washed.

When product does not operate properly as described in the operating instructions. Do not touch the controls other

than as described in the operating instructions. Improper adjustments of controls not described in the

instructions can cause damage, which can require extensive repair work by a qualied technician.

When the product has been dropped or damaged.

When the product displays an abnormal condition. Any noticeable abnormality in the product indicates that the

product needs servicing.

Replacement parts: In case the product needs replacement parts, make sure that the service person uses

replacement parts provided by SunBriteTV. Use of unauthorized parts can result in re, electric shock and/or other

danger.

Safety checks: Upon completion of service or repair work, ask the service technician to perform safety checks to

ensure that the product is in proper operating condition.

Important Safety Instructions

SunBriteTV Pro 2 Series Operator’s Manual

Page 5Page 5

Table of Contents

Important Safety Instructions

Table of Contents

Supplied Accessories

TV Installation

Choose a Location for the TV

Rear Panel Internal Connect Source

Rear Panel Connection Diagrams

Side Panel and Front Panel Controls

Remote Control Guide

On-Screen Display Controls

Adjusting On-Screen Displays

Channel Menu

Picture Menu

Sound Menu

Time Menu

Lock Menu

Option Menu

Media Menu

Information Menu

Troubleshooting

Care of SunBriteTV - Filter cleaning

Specications

Features Information and Instructions

Extreme Climate Warning

Programming Other Manufacturers’ Universal Remote Control Devices

SunBriteTV Pixel Quality Policy

Appendix A - RS232 Cable Pinout

Ir Emitter Installation

Appendix B - RS232 Control Codes

Page 6

Supplied Accessories

Unpacking

After unpacking the SunBriteTV television, please make sure that the following items are included in the carton and

that they are in good condition. If items are damaged or missing, contact your dealer immediately.

SunBriteTV LCD Television Operator’s Manual

Remote Control with Batteries

Pro 2 Series Outdoor TV

Quick Start Guide Remote Control

SunBriteTV Pro 2 Series Operator’s Manual

Page 7

TV Installation - Choose a Location for the TV

Choose a Location for the TV

Important: The TV must be installed at least 5

feet from pool, spa, or other body of water.

The TV should be installed so the screen is not facing

direct sunlight, or can be easily turned away from

direct sunlight.

Ideal placement is in an area where the TV is shaded

by trees, landscape and/or structures, or under a patio

cover or gazebo.

Remember that the position of the sun changes during

the day, as seen in the drawing at right., This means

that the quality of the picture will change during the

day. If you intend to install the TV in areas where direct

sunlight will reach it, it’s best to postion the TV for

optimum performance during the time of day when

you do most of your TV watching.

If the sun shines directly on the screen for long periods

of time, dark areas may develop on the screen. This is a

normal reaction for the LCD panel, and will not cause

damage to the screen. Either turn the screen away from

the sun, or apply shade to the TV, and the dark areas

will quickly disappear.

Page 8

TV Installation – Rear Panel Internal Connect Source - Cable routing

WARNING: Do not connect the power source before making connections.

Internal Connect Source through the cable access door.

The Internal Connect Source allows you to easily connect to the Audio, Video, VGA, HDMI, Audio Out, and RF connectors. The

internal connect Source are inside the cable cover located on the back of the unit (Figure1).

1. Unscrew the two Thumb Screws (Figure1), and pull the cover towards you.

2. Route the cables to the proper inputs, and place the cable cords over the Rubber Sealing Gasket on the bottom of the cable

access opening(Figure 2).

3. Be sure the cables are routed past the indentation on the bottom of the door. Cable cannot be routed through the top and side

of the rubber sealing gasket. (Figure 3).

3. Close the cover. Route the cables as shown to provide a drip loop below the door. This will prevent water from dripping down

the cord and possibly entering the door area.

4. Press rmly on the cover, and screw the Thumb Screws tightly (Figure4).

Figure 1

Figure 2

Figure 4

Rubber Sealing Gasket

Thumb Screws

TV Installation - Connecting the Power Cord

Do not connect power cord until all cable connections have been made. Connect the power cord to a GFCI, the rated residual

operating current shall not exceed 30mA, protected AC outlet with an “in-use” waterproof cover.

WARNING: TV AND GFCI RECEPTACLE, the rated residual operating current shall not exceed 30mA, MUST BE INSTALLED AT

LEAST 5 FEET AWAY FROM STANDING WATER , SUCH AS (BUT NOT LIMITED TO) A POOL OR SPA. BE SURE TO CHECK LOCAL

ELECTRICAL CODES AND COMPLY WITH THEIR LOCAL STANDARDS.

Route cables trough the

bottom of the door only

Figure 3

Drip Loop

Warning: Do not route cable from the top or sides of the cable access door. This

will prevent a proper seal of the cable compartment and will void your warranty.

SunBriteTV Pro 2 Series Operator’s Manual

Page 9

TV Installation – Rear Panel Connections

Connections

1. 5 pin din jack - SunBriteTV optional speaker bar connection output.

2. Direct IR input 3.5mm Jack

3. IR WINDOW - Rear IR receiver, allows IR emitter to be installed inside the cable compartment.

4. RS232 - 3.5mm Stereo Jack - For remote control using RS232 commands.

5. Ethernet- Network Connection - IP Control.

6. USB power port - 5vdc @ 3.5a Auxillary power supply (Power only - no data)

7. 1.3mm Power Jack - 5vdc @ 3.5a Auxillary power supply

8. HDMI 1 & 2 - Connects to devices that use HDMI cables such as Blu-ray or HD DVD player or HD cable / satellite set-top box. This connection

port receives pure digital audio and high denition signal through one single cable. This port also can accept a HDCP video device for video

or PC for monitor display usage. Use the SOURCE button to select HDMI1 on your MAIN SOURCE to view this connection. Please note: when

using HDMI, your sound signal must be PCM for the TV to decode digital audio. When using this source for PC display, you may have to

connect the audio cable to VGA Stereo Input for audio.

9. VGA - This connection port connects to a PC for video using VGA cable. Be sure to connect your audio cable to the VGA Stereo input if you

require sound out of the VGA video source. Use the SOURCE button to select PC on your MAIN SOURCE to view this connection

10. VGA STEREO INPUT - This connection 3.5mm jack provides audio to the TV when using a PC or a DVI video device. Use a 3.5mm mini-jack

audio cable (headphone jack) to provide audio for a HDCP enabled DVI video device or PCs with VGA or DVI connection.

11. AV (CVBS) - Connects to devices that use legacy composite cables such as older VCR or camcorder or video game consoles. Connect the

video portion with either the yellow connector. Use the SOURCE button to select AV on your MAIN SOURCE to view this connection.

12. COMPONENT - Requires use to 3.5mm to RCA cable. (not included) The RCA jacks are for DVD players or satellite/cable set-top boxes that

use component cables. From left to right, connect green, blue and red for video, and then connect white for left channel audio, red for right

channel audio. Use the Source Button to select Component to view this connection.

13. ANALOG AUDIO OUT (Variable) - Used to connect headphones, stereo receivers and amplied speakers via a 3.5mm headphone jack.

14. DIGITAL AUDIO OUT - This connection port is used for sending out audio signals to other audio devices such as stereo/surround sound

receivers. The optical TosLink connector sends out either bit-stream or PCM digital sound signal to a home theater receiver with digital input

15. ATSC/NTSC/QAM Coax input – This connection is for digital or analog cable without the cable box or over-the-airwave antennas. The tuner

is a hybrid tuner that tunes to both analog and digital channels. This connection uses coaxial RF cable. For over- the airwave digital stations

please check http://www.antennaweb.org.

16. USB SERVICE PORT - Can be used for photo and MP3 media playback or rmware updates using a USB ash drive.

See next

page

Warning: Connect a network connection with an active connection to a ethernet switch.

Page 10

17. HDbaseT - HD/UHD extender receiver.

Bottom Blue LED - indicates board power

Top Green LED - when lit indicates positive link to a HDBaseT transmitter

Left RJ45 Yellow LED - ashing = non-HDCP video transmitting/steady = HDCP video transmitting

Right RJ45 Green LED - Link from transmitter active

Warning: Do not connect HDbaseT to ethernet network based devices, damage to the HDbaseT receiver and/or the Ethernet

network device may result.

18. Emitter port - Connect an emitter to control the SunbriteTV through the HDBaseT compatible transmiter which supports IR repeating.

19. Option Switches- reserved for future use. Swith settings do not eect the HDBaseT operation at this time.

HDBase-T information

The Pro 2 Series 4K Ultra HD incorporates an HDBaseT receiver based on the SnapAV Binary B-520-RX-320.

A front IR receiver is incorporated into the design to extend the IR via the HDBaseT Transmitter and Receiver installation.

The IR repeater is dedicated to the integrated B-520-RX-320 and cannot be used with any other IR extender.

Refer to transmitter documentation for the support resolutions and color depth.

TV Installation – Rear Panel Connections

Connections continued

SunBriteTV Pro 2 Series Operator’s Manual

Page 11

TV Installation – Rear Panel Connections

Red

Green

Blue

Yellow

Green

Red

White

Connection Descriptions:

Cable Descriptions:

Legacy component input, 3.5mm to RCA

cable required for, not included

SunBrite Part Number CBL-35MM-COMP

Page 12

TV Installation – Rear Panel Connections

Switching Sources for Ports:

Your SunBrite TV oers several options when connecting

your devices to the TV. The chart below will help you

understand which source you switch to for each of the

ports.

CONNECTING TO AN ANTENNA

1. Make sure the power to the TV is turned o.

2. Connect the Coaxial RF cable from your

antenna or digital cable to the ATSC/NTSC port o

the back of the TV.

3. Turn on the TV.

4. Select TV (Air) for antenna or TV (Cable) for

digital cable from either your remote control’s

source button or source button on the right side

of the TV.

5. Use the On-Screen Display to scan for channels.

Connecting to Digital Cable without Cable Box or Antenna

Connecting to Cable or Antenna

1. Make sure the power of the TV is turned o.

2. Connect the Coaxial RF cable from your

antenna or cable to the

ATSC/NTSC port o the back of the TV.

3. Turn on the TV.

4. Select TV (Air) for antenna or TV (Cable) for

cable from either your remote control’s source

button or source button on the right side of the

TV.

5. Use the On Screen Display to scan for channels.

Please Note :

1. Not all broadcasts are in High Denition (HD). Please refer to your local broadcasting stations for more information.

2. The TV’s tuner is designed for HDTV therefore requires a stronger signal than normal TVs. If you cannot achieve that

signal level with your antenna or cable, the TV might lose picture or sound.

SunBriteTV Pro 2 Series Operator’s Manual

Page 13

TV Installation – Rear Panel Connection Diagrams

CONNECTING TO AN ANTENNA--(Continued)

Connecting to Cable or Antenna through VCR

1. Make sure the power of the TV is turned o.

2. Make sure there is an antenna or cable

connection to the VCR already.

3. Use a Coaxial RF cable and connect from your

VCR’s Antenna Out or Output to TV to the ATSC/

NTSC port of your TV.

4. Turn on the TV.

5. Select TV (Air) for antenna or TV (Cable) for

digital cable from either your remote control’s

source button or source button on the TV.

6. Use the On-Screen Display to scan for channels.

Please Note :

1. Some VCRs must be turned On before its output will have

a signal to the TV. Please consult your VCR manual for further

reference.

2. Not all broadcasts are in High Denition (HD). Please refer to

your local broadcasting stations for more information.

3. This model’s tuner is designed for HDTV therefore it requires a

stronger signal than normal TVs. If you cannot achieve that signal

level with your antenna or cable, the TV might lose picture or

sound.

4. This TV will turn o automatically if there’s no signal present

for more than 15 minutes.

1. Make sure the power of the TV and your DVD player is

turned o.

2. Connect a HDMI cable to the HDMI port of your DVD

player and the other end to the HDMI port o the back of

your TV.

3. Turn on the TV and your DVD player.

4. Use the remote control’s source button or the source

button on the TV to switch to HDMI.

1. Make sure the power of TV and your DVD player is turned o.

2. With a Component Cable, connect the green connector to the

DVD player and Component 1’s green connector port on the TV.

3. Connect the blue color connector to your DVD player and

Component 1’s blue connector port on the TV.

4. Connect the red color connector to both your DVD player and

Component 1’s red connector port on the TV.

5. With an RCA Audio Cable, connect the white color connector to

both your DVD player and Component 1’s white connector port

on the TV.

6. Connect the red color connector to both your DVD player and

7. Component adapter connector port on the TV.

8. Turn on the TV and your DVD player. Use the remote control’s

source button or the source button on the TV to switch to

component.

Connecting with HDMI (Best)

Connecting with

Component

(Better)

Please Note :

1. Refer to the DVD player’s manual to make sure the DVD

player is congured to output correctly to the TV.

2. This TV does not decode Bit stream digital audio, so make

sure the DVD is setup for PCM digital audio through

HDMI.

3. If HDMI 1 is occupied, use HDMI 2 as your connection

port.

CONNECTING TO A DVD PLAYER

Page 14

TV Installation – Rear Panel Connection Diagrams

CONNECTING TO A DVD PLAYER (Continued)

1. Make sure the power of the TV and your DVD player is

turned o.

2. Obtain a Yellow Video Cable. Connect the Yellow Video

connector to both your DVD player and Composite’s Yellow

Video connector port o the back of your TV.

3. Obtain a RCA Audio Cable. Connect the white color

connector to both your DVD player and Composite’s white

connector port o the back of your TV.

4. Connect the red color connector to both your DVD player

and Composite’s red connector port o the back of your TV.

5. Turn on the TV and your DVD player.

6. Use the remote control’s source button or the source

button on the right side of the TV to switch to AV1 (CVBS).

Connecting with

Composite (Fair)

Please note:

1. Reference the DVD player’s manual to make sure the DVD player is congured to output correctly to the TV.

2. This TV will turn o automatically if there’s no signal present for more than 15 minutes.

SunBriteTV Pro 2 Series Operator’s Manual

Page 15

TV Installation – Rear Panel Connection Diagrams

CONNECTING TO A SATELLITE OR CABLE SET-TOP BOX

1. Make sure the power of the TV and your set-top box is

turned o.

2. Connect a HDMI cable to the HDMI output of your set-top

box and the other end to the HDMI port o the back of

your TV.

3. Turn on the TV and your set-top box.

4. Use the remote control’s source button or the source

button on the right side of the TV to switch to HDMI 1.

Please Note :

1. Refer to the set-top box’s manual, to make sure the set-

top box is congured to output correctly to the TV.

2. If HDMI 1 is already occupied, use HDMI 1 as your

connection port and switch source to HDMI 2.

3. This model supports SONY’s universal remote code. If

SunBriteTV is not listed, please look up SONY’s codes in

your universal remote’s hand book.

4. This TV will turn o automatically if there’s no signal

present for more than 15 minutes.

1. Make sure the power of TV and your set-top box is turned o.

2. Obtain a Component Cable. Connect the green color

connector to both your set-top box and Component 1’s green

connector port o the back of your TV.

3. Connect the blue color connector to both your set-top box and

Component 1’s blue connector port o the back of your TV.

4. Connect the red color connector to both your set-top box and

Component 1’s red connector port o the back of your TV.

5. Obtain a RCA Audio Cable. Connect the white color connector

to both your set-top box and Component 1’s white connector

port o the back of your TV to the right side of your green,

blue, red component connection.

6. Connect the red color connector to both your set-top box and

Component 1’s red connector port o the back of your TV to

the right side of your green, blue, red component connection.

7. Turn on the TV and your set-top box.

8. Use the remote control’s source button or the source button

on the TV to switch to YPbPr1.

Please Note :

1. If Component 1 is already occupied, please use Component 2

is your connection port and switch to source YPbPr2.

2. Please refer to the set-top box’s manual to make sure the set-

top box is congured to output correctly to the TV.

3. This model supports SONY’s universal remote code. If

SunBriteTV is not listed, please look up SONY’s codes in your

universal remote’s hand book.

4. This TV will turn o automatically if there’s no signal present

for more than 15 minutes.

Connecting with HDMI (Best)

Connecting with

Component (Better)

Page 16

TV Installation – Rear Panel Connection Diagrams

CONNECTING TO A SATELLITE OR CABLE SET-TOP BOX (Continued)

1. Make sure the power of the TV and your DVD player is

turned o.

2. Obtain a Yellow Video Cable. Connect the Yellow Video

connector to both your DVD player and Composite’s Yellow

Video connector port o the back of your TV.

3. Connect the white color connector to both your DVD player

and Composite’s white connector port o the back of your

TV.

4. Connect the red color connector to both your DVD player

and Composite’s red connector port o the back of your TV.

5. Turn on the TV and your DVD player.

6. Use the remote control’s source button or the source button

on the right side of the TV to switch to AV1 (CVBS).

Please Note :

7. Refer to the set-top box’s manual to make sure the set-top

box is congured to output correctly to the TV.

8. This model supports SONY’s universal remote code. If

SunBriteTV is not listed, please look up SONY’s codes in your

universal remote’s hand book.

9. This TV will turn o automatically if there’s no signal present

for more than 15 minutes.

Connecting with

Composite (Fair)

SunBriteTV Pro 2 Series Operator’s Manual

Page 17

TV Installation – Rear Panel Connection Diagrams

1. Make sure the power of the TV and your receiver is turned o.

2. Obtain a optical cable, connect it to your receiver’s optical

digital input and the optical audio out jack on the TV.

3. Turn on the TV and your receiver.

Please Note :

1. If you want pure digital stream for your receiver to decode,

you must also congure the TV’s Sound->SPDIF mode

function. Make sure the option is on auto.

2. If your receiver is making static noises when receiving Bit

Stream, you must use the PCM option instead.

3. Refer to the receiver’s manual to make sure the receiver is

congured to receive signals correctly from the TV

1. Make sure the power of the TV and your receiver is turned o.

2. Obtain a HDMI to DVI conversion cable; connect the DVI side

of the conversion cable to the DVI output of your PC, and the

HDMI side of the conversion cable to the HDMI port o the

back of TV.

3. Obtain a 3.5 mm Mini-jack, connect to the audio out of your PC

and the other end to the VGA Stereo Input Port.

4. Turn on the power to the TV and the PC.

5. From the remote control’s source button, or the Source button

from the TVs panel, switch to HDMI.

Please Note :

1. For the best picture, set your PC resolution to 1920 x 1080

at 60 Hz. Refer to the PC or graphic card manual for further

instructions on how to set your resolution and refresh rate.

2. Refer to your PC manual for video output requirements of the

video card.

3. The TV will turn o automatically if there’s no signal present for

more than 15 minutes.

4. If HDMI 1 is already occupied, use HDMI 2 as your connection

port, and switch source to HDMI 2.

Continued on next page

Connecting with Optical Digital (Best)

CONNECTING TO A PC

Connecting with DVI Digital (Best)

1. Make sure the power of the TV and your receiver is turned

o.

2. Obtain a 3.5mm stereo/audio cable (if your amplier

audio connection requires RCA audio out jacks you

will need to obtain an 1/8” Stereo Mini Plug to RCA

adapter cable). Connect it to your receiver’s audio input

connection and the 3.5mm stereo/audio connection on

the Analog Audio port on the back of the TV.

3. Turn on the TV and your receiver.

Please Note :

1. If you want pure digital stream for your receiver to

decode, you must also congure the TV’s OSD Sound-

>Digital Audio Out function. Make sure the option is on

Bit Stream.

2. If your receiver is making static noises when receiving Bit

Stream, you must use the PCM option instead.

3. Refer to the receiver’s manual to make sure the receiver

is congured to receive signals correctly from the TV

Connecting with RCA Audio Analog (Good)

CONNECTING TO AN EXTERNAL AMPLIFIER OR AMPLIFIED SPEAKERS

Page 18

Connecting with VGA Analog (Good)

1. Make sure the power of the TV and your PC is turned o.

2. Obtain a 15-pin D-Sub VGA cable, connect to the VGA output of

your PC and the other end to the VGA port o the back of your

TV.

3. Obtain a 3.5 mm Mini-jack, connect to the audio out of your PC

and the other end to the VGA Stereo Input port.

4. Turn on the power of the TV and your PC.

5. Use the remote control’s source button or the source button the

TV to switch to VGA.

Please Note :

1. For the best results, please set your PC resolution to

2. 1920 x 1080at 60 Hz. Refer to the PC or graphic card’s manual

for further instructions on how to set your resolution and refresh

rate.

3. Refer to your PC manual for video output requirements of the

video card.

4. The VGA port of the TV features a power saving mode which will

automatically turn o the TV if there is no signal provided for

more than 15 minutes.

TV Installation – Rear Panel Connection Diagrams

CONNECTING TO A PC (Continued)

SunBriteTV Pro 2 Series Operator’s Manual

Page 19

TV Installation - Connecting the Power Cord

Power Turn on the TV by pressing the button once. Press the button again to

turn o the TV.

Input This button switches between the dierent sources of the TV. When the

On-Screen Display (OSD) is active, this button acts as the enter button

and conrms the menu selection.

Menu This button activates the OSD. If a sub-menu is active, pressing this

button will return selection to the previous menu level.

CH+/CH- These buttons change the TV channel up or down. If the OSD is active,

these buttons function as up or down controls for the menu.

Vol+ /Vol- These buttons increase or decrease the volume. If a sub-menu is active,

pressing these buttons will move the selection left or right. If the OSD is

active, Vol+/Vol- is used to select the highlighted options.

IR Sensor

LED power indicator

Ambient light sensor

Connect the power cord to a GFCI-protected AC outlet,

the rated residual operating current shall not exceed

30mA. with “in-use” waterproof cover.

Warning: TV must be installed at least 5 feet away from

standing water, such as (but not limited to) a pool or

spa.

Connecting the Power Cord

WARNING:

TV AND GFCI RECEPTACLE MUST BE INSTALLED AT LEAST 5 FEET AWAY FROM STANDING WATER, SUCH AS (BUT NOT LIMITED

TO) A POOL OR SPA, the rated residual operating current shall not exceed 30mA..

Connect the power cord after you have made connections to your video equipment.

Side Panel Controls

Front Panel

Page is loading ...

SunBrite SB-P2-32-1K-BL Owner's manual

Brand: SunBrite

Model: SB-P2-32-1K-BL

Category: LCD TVs

Type: Owner's manual

This manual is also suitable for

Download PDF

report

SunBrite SB-P2-32-1K-BL Owner's manual

This manual is also suitable for

SunBrite SB-P2-32-1K-BL Owner's manual

Related papers

Other documents