2. Computers & electronics
  3. Computer components
  4. Chassis components
  5. Computer cases
  6. Apevia
  7. ATXB2KL Series

Apevia ATXB2KL Series Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Apevia ATXB2KL Series Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • How do I install the motherboard standoffs?
    How do I install the motherboard?
    How do I install a case fan in the front panel?
    How do I install a case fan at the rear?
    How do I install a 5.25" drive?
    How do I install a 3.5" floppy disk drive?
    How do I install a 3.5" hidden drive?
    How do I connect the audio cables?
    How do I connect the power supply cables?
    How do I connect the front panel cables?
ATXB2KL Series Installation Guide
1:Unscrew the Thrum Screws 2.Pull the Side Panel back then 3:Find the motherboard Stand-Offs
from Side Panel. pull out. From the enclosed Screw Box.
4:Put the motherboard Stand-Offs 5.Sit the motherboard on the 6.Find screws in the Screw Box.
on the Motherboard Tray. Motherboard Tray.
7.Screw in all the screws into the 8.Same as Step 7.
Motherboard Stand-Offs
9.Take out front panel: (For installation of 5.25” drives and front fans)
Step (1): Unscrew the side Step (2): Take out the side Step (3): There are 4 screws that
Panel (motherboard side) panel (motherboard side) hold the front panel to the case. (2
on each side) Unscrew the 2 screws
from inside of the case.
Step (4): Unscrew the other Step (5): Pull out the front panel
2 screws from the other side. from the bottom.
10.Optional: Install Case Fan in 11.Optional: Install Case Fan at 12.Take out the metal plate and
the front panel (You can put up rear. (1*80mm-120mm fan) install 5.25” drives(DVD, CD-RW,
to 2*80mm fans in the front.) CD-ROM)
13.Secure the 5.25” drives 14.Slide in 3.5” FDD Drive and 15.Install 3.5” hidden drives such as
with screws secure with screws Hard Disk Drive, Zip Drive.
16.Screw all 3.5” hidden drives 17.Snap in the Front Panel and 18.Audio Cable: Take out the I/O slot
with screws. screw 4 screws back(2*each side) with a hole from the back of the case
to hold the front panel to the case.
.
19.Find the Audio Cables and 20.Put the I/O slot back. 21.Screw the I/O slot back.
Bring them through the I/O slot
to outside of the back panel.
22.Find the 4-pin connectors 23.Find the 20-pin connector 24.Plug into your motherboard.
(Female and Male) from case from Power Supply. Different M/B has different layout.
Fan. Connect the Male to the Please refer to your motherboard
Female 4-pin from Power Supply. user’s manual.
25.Find the 4-pin P4 connector 26.Plug into your motherboard. 27.Find 2*USB Cables.(USB1 & USB2)
from Power Supply.(for P4 only) (For Intel P4 motherboard only)
28.Plug USB Cables to your M/B. 29.Find “HDD LED” and 30.Plug them onto your M/B.
Please refer to M/B User’s Manual. “Reset SW” Cables. Please refer to M/B User’s Manual.
31.Find “Power SW” and “+P LED” 32.Plug Audio Cables to 33.Find “Case Speaker” from
“-P LED” Cables and plug onto M/B. Sound Card or M/B. Screw Box.
Please refer to M/B User’s Manual.
34.Install Case Speaker to M/B 35.Find “Case Feet” in Screw Box
following M/B User’s Manual. Lay your case down and put “Case Feet” on.
/