Blaupunkt CRP8 Owner's manual

OWNER'S MANUAL

INSTRUKCJA OBSŁUGI

NÁVOD K POUŽITÍ

NÁVOD NA POUŽITIE

HASZNÁLATI UTASÍTÁS

Projection Clock radio with USB charging

Radiobudzik z projektorem i ładowaniem USB

Radiobudík s projektorem a USB nabíjením

Rádiobudík s projektorom a USB nabíjaním

Projektoros ébresztőórás rádió USB töltéssel

Page is loading ...

CRP8BK / CRP8WH

2

IMPORTANT NOTES

g This safety and operating instruction should be retained for future reference.

g The apparatus should not be exposed to dripping or splashing or placed in a

humid atmosphere such as a bathroom.

g Do not install the product in the following areas:

̋ Places exposed to direct sunlight or close to radiators.

̋ On top of other stereo equipment that radiate too much heat. ocking

ventilation or in a dusty area.

̋ Areas where there is constant vibration.

̋ Humid or moist places.

̋ Do not place near candles or other naked flames.

g Operate the product only as instructed in this manual.

g Before turning on the power for the first time, make sure the power adaptor is

properly connected.

g Plug-in the USB stick directly or use an USB-extension cable which is not longer

than 25 cm.

For safety reasons, do not remove any covers or attempt to gain access to the inside of

the product. Refer any servicing to qualified personnel.

Do not attempt to remove any screws, or open the casing of the unit; there are no user

serviceable parts inside. Refer all servicing to qualified service personnel.

SAFETY INSTRUCTIONS

1. Read Instructions - All the safety and operating instructions must be read before the

product is operated.

2. Retain Instructions - The safety and operating instructions should be kept with the

product for future reference.

3. Heed warnings - All warnings on the product and in the operating instructions should

be adhered to.

4. Follow instructions - All operating and users’ instructions should be followed.

5. Water and moisture - To reduce the risk of fire or electric shock, do not expose the

product to train, dripping, splashing or excessive moisture such as in a sauna or bathroom.

Do not use this product near water, for example, near a bathtub, washbowl, kitchen sink,

laundry tub, in a wet basement or near a swimming pool (or similar).

6. Object and Liquid Entry - Never push objects of any kind into this product through

openings, as they may touch dangerous voltage points or short-circuit parts that could

result in a fire or electric shock. Never spill liquid of any kind on the product. Do not place

any object containing liquid on top of the product.

7. Servicing - Do not attempt to service this product yourself, as opening or removing

covers may expose you to dangerous voltage or other hazards. Refer all servicing to

qualified service personnel.

8. Replacement parts - When replacement parts are required, ensure that the service

technician has used replacement parts specified by the manufacturer or have the same

characteristics as the original part. Unauthorized substitutions may result in fire, electric

shock or other hazards.

ENGLISH

CRP8BK / CRP8WH

3

9. Place your clock radio on a stable surface, away from sources of direct sunlight or

excessive heat or moisture.

10. Protect your furniture when placing your units on a natural wood and lacquered finish

by using a cloth or protective material between it and the furniture.

11. Clean your unit with a soft cloth moistened only with mild soap and water. Stronger

agents such as Benzine, thinner or similar materials can damage the surface of the unit.

Make sure the unit is unplugged before cleaning.

12. Battery

1). The batteries must not be exposed to excessive heat such as sunshine, fire or the like.

2). The batteries should be drawn to the environmental aspects of battery disposal.

3). Battery usage CAUTION-to prevent battery leakage which may result in body injuries,

property damage, or damage to the apparatus:

-Install all batteries correctly, + and – as marked on the apparatus.

-Remove batteries when the unit is not used for a long time.

WARNING

This appliance is not intended for use by persons (including children) with reduced

physical sensory or mental capabilities, or lack of experience and knowledge, unless they

have been given supervision or instruction concerning use of the appliance by a person

responsible for their safety. Children should be supervised to ensure that they do not play

with the appliance.

1. The apparatus must not be exposed to dripping or splashing and that objects filled

with liquids, such as vases, must not be placed on the apparatus.

2. To prevent fire or shock hazard, do not expose this equipment to hot places, rain,

moisture or dust.

3. Do not locate this unit near any water sources e.g. taps, bathtubs, washing machines or

swimming pools. Ensure that you place the unit on a dry, stable surface.

4. Do not place this unit close to a strong magnetic field.

5. Do not place the unit on a amplifier or receiver.

6. Do not place this unit in a damp area as the moisture will affect the life of electric

components.

7. If the clock is brought directly from a cold to a warm location, or is placed in a very

damp room, moisture may condense on the lens inside the player. If this occurs, the

system will not operate properly. Please leave the system turned on for about an hour

until the moisture evaporates.

8. Do not attempt to clean the unit with chemical solvents as this might damage the finish.

Wipe with a clean, dry or slightly damp cloth.

CRP8BK / CRP8WH

4

NOTICE

This product complies with the radio interference requirements of the European

community.

Your products is designed an manufactured with high quality materials and components,

which can be recycled and reused.

When this crossed-out wheeled bin symbol is attached to a product it means that the

product is covered by the European Directive 2002/96/EC. Please inform yourself about

the local separate collection system for electrical and electronic products. Please cat

according to your local rules and do not dispose of your old products with your normal

household waste. Correct disposal of your old product helps to prevent potential

negative consequences for the environment and human health.

Your product contains batteries covered by the European Directive 2006/66/EC, which

cannot be dispose with normal household waste. Please inform yourself about the local

rules on separate collection of batteries because correct disposal helps to prevent

negative consequences for the environmental and human health.

Environmental information

All unnecessary packaging has been omitted. We have tried to make the packaging easy

to separate into three materials: cardboard(box), polystyrene foam(buffer) and poly

ethylene (bags, protective foam sheet). Your system consists of material which can be

recycled and reused if disassembled by a specialized company. Please observe the local

regulations regarding the disposal of packaging materials, exhausted batteries and old

equipment. Recording and playback of material might require consent. See Copyright Act

1956 and The Performer's Protection Acts 1958 to 1972.

ENGLISH

CRP8BK / CRP8WH

5

CONTROLS AND FUNCTION

TOP VIEW

FRONT VIEW

NAP/UP

PROJECTOR

DOWN/PROJECTION

VOLUME RADIO/SLEEP SNOOZE/DIMMER

ALARM 1-2

SET/MEMORY

TIME

ALARM 1

ALARM 2

PIM INDICATOR

SLEEP

NAP TIMER

BATTERY DOOR

DC SOCKET

AUX LINE-IN

USB SOCKET (FOR CHARGI

ROTARY KNO

INSERT AC/DC

ADAPTOR JACK

AC/DC ADAPTO

THE BATTERY COMPARTMENT: INSERT 1 X CR2032 BA

INSIDE THE BATTERY COMPARTMENT

BACK VIEW

CRP8BK / CRP8WH

6

INSTALLATION

Plug the AC/DC adaptor to an AC household outlet, and then plug the DC jack to the back

of the unit. Your clock radio is ready to work for you.

BACKUP BATTERY INSTALLATION

Your clock radio requires one CR2032 lithium battery (not included) to provide backup

power to the clock in the event of a temporary power interruption.

1. Place your unit face down on a flat surface.

2. Slide and remove the battery cover at the bottom of your unit.

3. Insert one new CR2032 lithium battery into the battery compartment with the “+” side

facing up as indicated.

4. Replace the battery cover.

If AC power is interrupted, the LED display will go off and both the radio and the alarm

will not function. The backup battery will keep the time and all settings of your unit.

Make sure a fresh CR2032 lithium battery is used. A fresh CR2032 battery could backup

your clock continuously.

SETTING TIME, 12/24HR TIME AND THE SNOOZE DURATION

1. Press SET once, the hour digits flash. Press Ʒ or ͩ to set the current hour (hold to

advance rapidly).

2. Press SET again, the minute digits flash. Press Ʒ or ͩ to set minutes.

3. Press SET again, the display shows “24H” and flashes, press Ʒ or ͩ to select “12H” or

“24H” time format.

4. Press SET again, the display shows “05” and flashes, press Ʒ or ͩ to select your snooze

time from 5 to 60 minutes.

5. Press SET again or if no key pressed for approx. 10 seconds to exit the setting mode.

Note: when 12-hour time format is selected, the P (PM) icon will appear on the lower

middle time display to indicate the afternoon time; there is no AM indicator.

SETTING THE ALARMS

1. Press AL 1.2 once, the 1 icon and the hour digits flash. Press Ʒ or ͩ to set the alarm 1

hours.

2. Press AL 1.2 again to adjust minutes. Press Ʒ or ͩ to set the alarm 1 minutes.

3. Press AL 1.2 again, LED displays “OFF” (alarm off). To select wake to sound sources, press

Ʒ or ͩ to select :-

rd = wake-by-radio

bu = wake-by-buzzer

OFF = alarm off

4. Press AL 1.2 again, the 2 icon and the hour digits flash. Press Ʒ or ͩ to set the alarm 2

hours.

5. Repeat step 2) and 3) to set alarm 2.

6. Press AL1.2 again or no button around 10 seconds to exit alarm setting mode. When

wake-to-radio or wake-to-buzzer is selected, the related alarm is turned on, indicated by

appearance of the 1 and / or the 2 icon on the left side of the display.

ENGLISH

CRP8BK / CRP8WH

7

STOPPING AND RESETTING THE ALARM TO COME ON THE NEXT DAY

When alarm 1 or 2 is sounding, the related 1 or 2 icon flashes. Press the AL 1.2 once to

stop the alarm and reset it to come on the following day. After that 1 or 2 icon keep

lighting up on the display.

Note: When alarm is sounding, press the Ʒ / NAP or RADIO / SLEEP will activate the nap

timer or the radio and stop the alarm for the day. Do not plug in the AUX cable to the unit

overnight as this will prohibit the alarms from functioning.

SNOOZE OPERATION (default snooze duration is 5 minutes)

When alarm is sounding, presses

once, the alarm will be silenced and come on

again after the set snooze duration.

Note: if your second alarm activates while the first alarm is sounding or it is in the snooze

mode, the second alarm overrides the first alarm (the first alarm is reset to come on the

next day).

USING THE HI-LO DIMMER

Press

to adjust the brightness of the LED display. This can only be done when the

radio is off or the unit is not sounding.

USING THE NAP TIMER

The NAP Timer allows you to rest and automatically wake up in 5, 15, 30, 45, 60, 75 or 90

minutes.

1. Press Ʒ / NAP once, the display shows the nap icon and the default naptime “05” (5

minutes).

2. Press Ʒ / NAP again to select your desired naptime. It will exit to time display if no

button pressed for 5 seconds.

3. The nap icon lights up when the nap timer is counting. When the nap timer reaches 0,

the alarm will sound and the nap icon will flash. Press Ʒ / NAP once to stop the nap alarm,

the nap icon will go off.

Note: If the nap time is set up then your alarm is sounding, your nap time will be

cancelled automatically.

SETTING UP THE FM ANTENNA

Extend the FM wire antenna fully and vary the direction for best FM reception. Do not

strip, alter or attach to other antennas.

LISTENING TO THE FM RADIO

1. To turn on the radio, press SLEEP/RADIO once, the display shows “ON” and then the

radio frequency readings in Mhz.

2. Press Ʒ or ͩ to tune the radio to a desired station. Press and hold Ʒ or ͩ to scan for

the next clear station.

3. To adjust the volume, press VOL once, the display shows“L07”, press Ʒ or ͩ to adjust

volume from L01 (minimum) to L15 (maximum)

4. Press

to turn off the radio.

CRP8BK / CRP8WH

8

Remark: keep your radio away from fluorescent lamps or other electronic devices, which

may cause interference to the radio.

USING THE PRESET MEMORY

This clock radio features a total of 10 preset memories of FM stations. These allow you to

preset your favorite stations and access them quickly.

1. Turn on the radio and select a radio station you like to memorize.

2. Press and hold the SET appears and “01” flashes. Press SET once to store Memory 1.

3. Press Ʒ or ͩ to select another station you like to memorize. Then press and hold SET

appears and “01” flashes. Press Ʒ or ͩ once, “02” appears. Press SET once to store

Memory 02.

4. Repeat Step 2 to 3 to preset memories 3 through 10.

5. To access a preset station at any time, press the SET one at a time while the radio is on.

6. To edit a preset station, select another station and then repeat Step 2 to 4. This

overrides the original settings.

USING THE SLEEP TIMER

1. Press the RADIO/SLEEP twice to enter the sleep mode. The sleep icon “L” and the sleep

time “05” (5 minutes) and will flash on the display.

2. Press the RADIO/SLEEP again as needed to adjust the sleep timer from 15, 30, 45, 60, 75

or 90 minutes.

3. When the display changes back to show the time, press the RADIO/SLEEP once to show

the sleep time remaining.

4. The radio will play for the programmed sleep time and then shut off.

5. To turn off the radio before the sleep time has elapsed, press

once.

USING THE PROJECTION

Press ͩ once at the left side of your unit to turn on or off the projection.

When the projection is on, press and hold ͩ to flip the projected time upside down.

At the back of your unit, turn the rotary knob to rotate the projected time by 90 degree.

TO USE THE AUX FUNCTION TO PLAY MUSIC IN YOUR IPHONE, IPOD OR MP3

You could play the music in your iPhone, iPod or MP3 device by using the AUX function.

1. Plug in the AUX cable to the AUX Line-in socket at the back of your Radio Alarm Clock

and one end to the earphone socket of your iPhone, iPod or MP3 device.

2. Turn on your MP3, iPhone or iPod to play the music you like.

Note: when you plug in the AUX cable, it will no function of the RADIO/ SLEEP function,

volume of the unit can’t be adjusted when it in AUX function.Do not plug in the AUX cable

to the unit overnight as this will prohibit the alarms from functioning.

ENGLISH

CRP8BK / CRP8WH

9

USB charging your mobile phones:

Plug in the USB cable into the USB Charge Out port, then connect the opposite end to

your phones for changing.

Note: The USB charge spec. is 5.0V/500MA; the original USB cable is required for Charging.

There will cause some damages if illegal cable were using.

TROUBLE SHOOTING

If your clock displays irrelevant time or does not function properly, which maybe caused

by electro-static discharge or other interference, unplug the DC jack to disconnect the AC

power (and remove the backup battery). The clock radio will be reset to default settings

and you need to set it again.

SPECIFICATIONS

Alarm duration: 1 hour (3-minute on, 9-minute off interval)

Snooze duration: 5 to 60 minutes

Nap timer duration: 5 minutes Nap timer selections: 5, 15, 30, 45, 60, 75, 90 minutes to

OFF

Sleep timer selections: 5, 15, 30, 45, 60, 75, 90 minutes to OFF

Volume: L01 (minimum) to L15 (maximum)

Preset Memories of radio: 10

USB charging: 5V, 500Ma

Power adaptor: 5.5V, 550mA

Default settings:-

Time format: 24 hour

Time: 0:00

Alarm 1 and 2: 0:00

Volume: L07 (Level 7)

Snooze duration: 05 (5 minutes)

Page is loading ...

CRP8BK / CRP8WH

23

TLAČÍTKA A FUNKCE

POHLED SHORA

POHLED ZEPŘEDU

PROJEKTOR

ŠIPKA DOLŮ / PROJEKCE

HLASITOST (VOL)

RÁDIO / OPAKOVANÉ BUZENÍ

OPAKOVANÉ BUZENÍ / JAS

BUZENÍ 1-2

SET / PAMĚŤ

OPAKOVANÉ BUZENÍ (NAP)

/ ŠIPKA NAHORU

BUZENÍ 1

ČAS

BUZENÍ 2

UKAZATEL PM

OPAKOVANÉ BUZENÍ

ČASOVAČ OPAKOVANÉHO BUZENÍ

Page is loading ...

Blaupunkt CRP8 Owner's manual

This manual is also suitable for

Blaupunkt CRP8 Owner's manual

in other languages

Related papers

Other documents