Craftsman 917773711 Owner's manual

Brand: Craftsman

Model: 917773711

Category: Garden tools

Type: Owner's manual

This manual is also suitable for

917.773710

Owner's Manual

(RRFTSMRH'°

EEDTRI E

625 Series Briggs & Stratton Engine

22 Inch Cut

Model No.

917.773711

. Espahot, p. 17

_IbCAUTION:

Read and follow all

Safety Rules and Instructions

before operating this equipment.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Visit our Craftsman website: www, sears,com/craftsman

Warranty .................................................... 2

Safety Rules ........................................... 2-4

Product Specifications .............................. 5

Assembly / Pre-Operation ......................... 5

Operation ............................................... 6-8

Maintenance Schedule ............................. 9

Maintenance ......................................... 9-11

Service and Adjustments ................... 12-13

Storage .................................................... 14

Troubleshooting ...................................... 15

Repair Parts ........................................ 32-41

Sears Service ........................... Back Cover

LIMITED TWO YEAR WARRANTY ON CRAFTSMAN WEEDTRIMMER

For two (2) years from date of purchase, when this Craftsman Weedtrimmer is main-

tained, lubricated, and tuned up according to the operating and maintenance instruc-

tions in the owner's manual, Sears will repair free of charge any defect in material or

workmanship.

If this Craftsman Weedtrimmer is used for commercial or rental purposes, this warranty

applies for only 90 days from the date of purchase.

This Warranty does not cover:

o Expendable items which become worn during normal use, such as rotating lines,

belts, air cleaners and spark plug.

Repairs necessary because of operator abuse or negligence, including bent crank-

shafts and the failure to maintain the equipment according to the instructions con-

tained in the owner's manual.

Warranty service is available by returning the Craftsman Weedtrimmer to the nearest

Sears Parts & Repair Center in the United States. This warranty applies only while this

product is used in the United States.

This Warranty gives you specific legal rights, and you may also have other rights which

vary from state to state.

Sears, Roebuck and Co., Dept. 817 WA, Hoffman Estates, IL 60179

A WARNING: This trimmer is equipped with an internal combustion engine and

should not be used on or near any unimproved forest-covered, brush-covered or grass-

covered land unless the engine's exhaust system is equipped with a spark arrester

meeting applicable local or state laws (if any). If a spark arrester is used, it should be

maintained in effective working order by the operator.

In the state of California the above is required by law (Section 4442 of the California

Public Resources Code). Other states may have similar laws. Federal laws apply on

federal lands. A spark arrester for the muffler is available through your nearest Sears

service center (see the REPAIR PARTS section of this manual).

SAFETYGLASSES

&Look for

important safety precautions. It means

CAUTION!!! BECOME ALERT!!!

YOUR SAFETY IS INVOLVED.

The operation of any trimmer can result in foreign objects thrown into

the eyes, which can result in severe eye damage. Always wear safety

glasses or eye shields while operating your trimmer or performing any

adjustments or repairs. We recommend standard safety glasses or a

wide vision safety mask worn over spectacles.

this symbol to point out AWARNING:lnordertopreventaccidental

starting when setting up, transporting, ad-

justing or making repairs, always disconnect

spark plug wire and place wire where it

2 cannot contact plug.

_kWARNING: Engine exhaust, some

of its constituents, and certain vehicle

components contain or emit chemicals

known to the State of California to cause

cancer and birth defects or other reproduc-

tive harm.

A CAUTION: Muffler and other engine parts

become extremely hot during operation and

remain hot after engine has stopped. To

avoid severe burns on contact, stay away

from these areas.

I. GENERAL OPERATION

• Read, understand, and follow all instruc-

tions on the machine and in the manual

before starting. Be thoroughly familiar

with the controls and the proper use of

the machine before starting.

• Do not put hands or feet near or under

rotating parts.

• Keep all parts of your body away from

muffler and spinning line. A hot muffler

can cause serious burns.

• Only allow responsible individuals, who

are familiar with the instructions, to oper-

ate the machine.

• Stayawayfrom breakable objects, such as

house windows, auto glass, greenhouses,

etc.

• Clearthe area ofobjects such as rocks,toys,

wire, bones, sticks, etc., which could be

picked up and thrown bythe spinning lines.

• Be sure the area is clear of other people

before trimming, particularly small chil-

dren and pets. Stop machine if anyone

enters the area.

• Wearappropriate clothing such as a long-

sleeved shirt or jacket. Also wear long

trousers or slacks. Do not wear shorts.

• Do not wear loose clothing which could

get caught in this equipment.

• Do not operate the machine when bare-

foot or wearing open sandals. Always

wear work gloves and sturdy footwear.

Leather work shoes or short boots work

well for most people. These will protect

the operator's ankles and shins from small

sticks, splinters, and other debris, and

improve traction.

• Do not pull machine backwards unless ab-

solutely necessary. Always look down and

behind beforeandwhile moving backwards.

• Do not operatethe machine without proper

guards, plates or other safety protective

devices in place.

• See manufacturer's instructionsforproper

operation and installation of accessories.

Only use accessories approved by the

manufacturer.

• Never use blades, wire, orflailing devices.

This unit is designed for line trimmer use

only. Use of other accessories or attach-

ments will increase the risk of injury.

• Stop the rotating trimmer head when

crossing gravel drives, walks, or roads.

Wait for the cutting lines to stop rotat-

ing.

• Stop the engine (motor) whenever you

leave the equipment and allow it to cool,

before cleaning, repairing or inspecting

the unit. Be sure the trimmer head and

all moving parts have stopped.

• Operate only in daylight or good artificial

light.

• Do not operate the machine while under

the influence of alcohol or drugs.

• Never operate machine in wet grass.

Always be sure of your footing: keep a

firm hold on the handle and walk; never

run.

• If the equipment should start to vibrate

abnormally, stop the engine (motor) and

check immediately for the cause. Vibra-

tion is generally a warning of trouble.

• Always wear safety goggles or safety

glasses with side shields when operating

machine.

II. SLOPE OPERATION

Slopes are a major factor related to slip and

fall accidents which can result in severe in-

jury. All slopes require extra caution. If you

feel uneasy on a slope, do not trim it.

DO:

• Trim across the face of slopes: never up

and down. Exercise extreme caution when

changing direction on slopes.

• Remove obstacles such as rocks, tree

limbs, etc.

• Watch for holes, ruts, or bumps. Tall grass

can hide obstacles.

DO NOT:

• Do not trim near drop-offs, ditches or

embankments. The operator could lose

footing or balance.

• Do not trim excessively steep slopes.

• Do not trim on wet grass. Reduced footing

could cause slipping.

ill. CHILDREN

Tragic accidents can occur if the operator

is not alert to the presence of children.

Childrenareoftenattractedto the machine

and the trimming activity. Never assume

that children will remain where you last

saw them.

• Keep children out of the trimming area

and under the watchful care of another

responsible adult.

• Be alert and turn machine off if children

enter the area.

• Before and while moving backwards, look

behind & down for small children.

• Never allow children to operate the ma-

chine.

• Use extra care when approaching blind

corners, shrubs, trees, or other objects

that may obscure vision.

iV, SERVICE

• Use extra care in handling gasoline and

other fuels. They are flammable and

vapors are explosive.

Use only an approved container.

Never remove gas cap or add fuel with

with the engine running. Allow engine

to cool before refueling. Don't smoke.

Never refuel the machine indoors.

Never store the machine or fuel

container inside where there is an

open flame, such as a water heater.

Move away from fueling site before

starting engine.

• Never run trimmer inside a closed area.

• Never make adjustments or repairs with

the engine (motor) running. Disconnect

the spark plug wire, and keep the wire

away from the spark plug to prevent ac-

cidental starting.

• Keep nuts and bolts, especially trimmer

head and engine bolts, tight and keep

equipment in good condition.

• Never tamper with safety devices.

Check their proper operation regularly.

• Keep machine free of grass, leaves, or

other debris buildup. Clean oil or fuel

spillage. Allow machine to cool before

cleaning or storing.

• Stop and inspect the equipment if you

strike an object. Repair, if necessary,

before restarting.

• Do not changethe engine governorsetting

or overspeed the engine.

• Clean and replace safety and instruction

decals as necessary.

Repair Protection Agreements

Congratulations on making a smart pur-

chase. Your new Craftsman® product is

designed and manufactured for years of

dependable operation. But like all prod-

ucts, it may require repair from time to

time. That's when having a Repair Protec-

tion Agreement can save you money and

aggravation.

Purchase a Repair Protection Agreement

now and protect yourself from unexpected

hassle and expense.

Here's what's included in the Agreement:

• Expert service by our 12,000 profe-

sional repair specialists.

• Unlimited service and no charge for

parts and labor on all covered repairs.

• Product replacement if your covered

product can't be fixed.

• Discount of 10% from regular price of

service and service-related parts not

covered by the agreement; also, 10%

off regular price of preventive mainte-

nance check.

Fast help by phone - phone support

from a Sears technician on products

requiring in-home repair, plus conve-

nient repair scheduling.

Once you purchase the Agreement, a

simple phone call is all that it takes for you

to schedule service. You can call anytime

day or night, or schedule a service ap-

pointment online.

Sears has over 12,000 professional repair

specialists, who have access to over 4.5

million quality parts and accessories.

That's the kind of professionalism you can

count on to help prolong the life of your

new purchase for years to come. Pur-

chase your Repair Protection Agreement

today!

Some limitations and exclusions apply.

For prices and additional information

call 1=800=827=6655.

Sears installation Service

For Sears professional installation of home

appliances, garage door openers, water

heaters, and other major home items, in

the U.S.A. call 1=800-4-MY=HOME®.

SerialNumber:

Dateof Purchase:

GasolineCapacity/ Type: 1.6 Quarts (Unleaded Regular)

Oil Type (API SG-SL): SAE 30 (above 32°F); SAE 5W-30 (below 32°F)

Oil Capacity: 20 Ounces

Spark Plug (Gap: .030") Champion RJ19LM or J19LM

Trimmer Line Length: 18.75 Inches (0.155 Inch Diameter)

• The model and serial numbers will be found on a decal on the rear of the trimmer.

Record both serial number and date of purchase in the space provided above.

Read these instructions and this manual

in its entirety before you attempt to as-

semble or operate your new trimmer.

IMPORTANT: This trimmer is shipped WITH-

OUT OIL OR GASOLINE in the engine.

Your new trimmer has been assembled

at the factory with the exception of those

parts left unassembled for shipping

purposes. All parts such as nuts, wash-

ers, bolts, etc., necessary to complete the

assembly have been placed in the parts

bag. To ensure safe and proper operation

of your trimmer, all parts and hardware

you assemble must be tightened securely.

Use the correct tools as necessary to

ensure proper tightness.

When right hand (RH) or left hand (LH) is

mentioned in this manual, it means when

you are in the operating position (stand-

ing behind the handle).

Loose Parts Packed Separately

HOW TO SET UP YOUR TRIMMER

TO UNFOLD HANDLE

IMPORTANT: Unfold handle carefully so

as not to pinch or damage control cables.

1. Loosen handle knob enough to allow

upper handle to be unfolded from the

shipping position.

2. Raise upper handle section into place on

lower handle and tighten handle knob.

3. Remove handle padding holding trim-

mer head control bar to upper handle.

Your trimmer handle can be adjusted for

your trimming comfort. Refer to "ADJUST

HANDLE" in the Service and Adjustments

section of this manual.

Upper handle

LIFT UP

Bottle of oil Trimmer Lines (2) Sets

(0,155 diameter

x 18.75 inches long)

REMOVE TRIMMER FROM

CARTON

1. Remove Ioosepartsincludedwithtrimmer.

2. Cut down two end corners of carton

and lay end panel down flat.

3. Remove all packing materials.

4. Rolltrimmeroutofcartonand checkcar-

ton thoroughlyforadditional loose parts. 5

Handle

knob

Lower

handle

KNOW YOUR TRIMMER

READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR

TRIMMER. Compare the illustrations with your trimmer to familiarize yourself with the

location of various controls and adjustments. Save this manual for future reference.

These symbols may appear on your trimmer or in literature supplied with the product. Learn

and understand their meaning.

FAST SLOW CAUTION ENGINE OFF FUEL

INJURYORDEATH

Trimmer head control bar

Throttle control

Starter handle

Engine oil cap

with dipstick

Handle

Gasoline cap

Air filter

Primer

Muffler

Chassis cover

Trimmer head

IMPORTANT: This trimmer is shipped

WITHOUT OIL OR GASOLINE in the engine.

Trimmer head control bar = must be held

down to the handle to engage trimmer

head. Release to stop the trimmer head.

Primer = pumps additional fuel from the

carburetor to the cylinder for use when

starting a cold engine.

line

Throttle control = used for starting and

stopping the engine and allows you to se-

lect either FAST or SLOW engine speed.

Starter handle = used for starting the

engine.

Theoperation of anytrimmer can result

inforeign objects beingthrown intothe

eyes,which can result in severeeye dam-

age. Alwayswearsafetyglassesor eye

shields while operating your trimmeror

performingany adjustmentsor repairs.

We recommendstandardsafetyglasses

ora widevisionsafetymaskworn over

spectacles.

HOW TO USE YOUR TRIMMER

ENGINESPEED

Theengine speed is controlled by a

throttle located on the side of the up-

per handle. FAST position is for starting

and normal trimming. SLOW is for light

trimming and fuel economy. STOP is for

stopping the engine.

TO ADJUST TRIMMING HEIGHT

II:ICAUTION: Stop the engine and wait

for all moving parts to stop. Disconnect

spark plug wire from spark plug and place

wire where it cannot come in contact with

plug.

The height of cut can be set to six (6) dif-

ferent positions ranging from 1-1/2 inches

to 3 inches. Recommended cutting height

for the average yard is 2 inches.

1. To adjust trimming height, push in the

locking plate tab and move trimmer

head up or down to desired position.

2. Release tab and be sure head is

locked into one of the six (6) height

positions.

Adj

Trimmer

Head

Locking

Plate Tab

FAST

S LOW

TRIMMER HEAD DRIVE CONTROL

Your trimmer is equipped with a trimmer

head drive control bar which will require

the operator to be positioned behind the

trimmer handle to operate the trimmer.

• Trimmer head rotation is controlled by

holding the trimmer head control bar

down to the handle.

• Trimmer head rotation will stop when

the control bar is released.

BEFORE STARTING ENGINE

ADD OIL

Your trimmer is shipped without oil in the

engine. For type and grade of oil to use,

see "ENGINE" in the Maintenance section

of this manual.

CAUTION: DO NOT overfill engine with

oil, or it will smoke heavily from the muffler

on startup.

1. Be sure trimmer is level.

2. Remove oil dipstick from oil fill spout.

3. You receive a container of oil with the

unit. Slowly pour the entire container

down the oil fill spout into the engine.

4. Insert and tighten dipstick.

IMPORTANT:

• Check oil level before each use. Add

oil if needed. Fill to full line on dipstick.

• Change the oil after every 25 hours of

operation or each season. You may

need to change the oil more often un-

der dusty, dirty conditions.

ADD GASOLINE

• Fillfueltankto bottomof gastank

filler neck. Do not overfill. Usefresh,

clean, regular unleadedgasolinewith a

minimumof 87 octane. Do not mixoil

with gasoline. Purchasefuel in quanti-

tiesthat can be usedwithin30 days to

assurefuel freshness.

A CAUTION: Wipe off any spilled oil or

fuel. Do notstore, spill or usegasoline

nearan openflame.

_CAUTION: Alcohol blendedfuels

(calledgasohol or using ethanol or

methanol) can attract moisture which

leads to separation and formation of acids

during storage. Acidic gas can damage

the fuel system of an engine while in

storage. To avoid engine problems, the

fuel system should be emptied before

storage of 30 days or longer. Empty

the gas tank, start the engine and let it

run until the fuel lines and carburetor

are empty. Use fresh fuel next season.

See Storage Instructions for additional

information. Never use engine or

carburetor cleaner products in the fuel

tank or permanent damage may occur.

Gasoline filler ine

ca oil cap

Primer

TO STOP ENGINE

• To stop engine, move throttle control

lever to STOP position.

TO START ENGINE

1. To start a cold engine, push primerthree

(3) times before trying to start. Use a firm

push. This step is not usually neces-

sary when starting an engine which has

already run for a few minutes.

2. Move throttle control lever to FAST

position.

3. Hold upper handle firmly and pull

starter handle quickly. Do not allow

starter rope to snap back.

NOTE: In cooler weather it may be

necessary to repeat priming steps. In

warmer weather overpriming may cause

flooding and engine will not start. If

you do flood engine, wait a few minutes

before attempting to start and do not

repeat priming steps.

Starter

handle

TRIMMING TIPS

• Set the throttle control in the FAST posi-

tion. If the weeds or grass are tall and

thick, operate the trimmer at a slower

walking speed.

• Frequently clean the underside of the

trimmer to remove any grass build up.

Keep top of engine around starter clear

and clean of grass clippings and chaff.

This will help engine air flow and extend

engine life.

• For best results and longer lasting

line, use the ends of the line to do the

cutting. This is easily done by moving

slowly through very thick and heavy

weeds.

• Use the left side of trimmer when trim-

ming along fences, walls, flowerbeds

and other such objects.

• If trimmer lines become too short, it

will take longer to complete the job. If

trimmer lines are worn to less than half

their original length, they should be

replaced. See "TO REPLACE TRIMMER

LINE" in the Maintenance section of this

manual.

• Trimmer head contact with concrete, as-

phalt or other hard surfaces may cause

premature wear of the ball on bottom of

trimmer head.

.A..T..A.C,SC..OU',

F,,,,NOATES ......

AS YOU COMPLETE /__._O_Y SERVICE

REGULAR SERVICE /__:x'_..,." 4'r_'_'- "Z DATES

Check for Loose Fasteners if I_

Clean Trimmer If If

Clean Under Engine Cover 1_2 if

Check Drive Belt / Pulleys

R Check / Replace Trimmer Lines Ill3

Check Engine Oil Level I_

Change Engine Oil _1,2

Clean Air Filter I_ 2

Inspect Muffler I_

Clean or Replace Spark Plug

Replace Air Filter Paper Cartridge 1_2

1 - Change more often when operating under a heavy load or in high ambient temperatures.

2 - Service more often when operating in dirty or dusty conditions.

3 - Replace trimmer lines when they have worn to half their original length.

GENERAL RECOMMENDATIONS

The warranty on this trimmer does not

cover items that have been subjected to

operator abuse or negligence. To receive

full value from the warranty, operator must

maintain trimmer as instructed in this

manual.

Some adjustments will need to be made

periodically to properly maintain your unit.

At least once a season, check to see if

you should make any of the adjustments

described in the Service and Adjustments

section of this manual.

• At least once a year, replace the spark

plug and replace air filter element. A

new spark plug and clean/new air filter

element assure proper air-fuel mixture

and help your engine run better and

last longer.

• Followthe maintenance schedule in

this manual.

BEFORE EACH USE

1. Check engine oil level.

2. Check for loose fasteners.

3. Clean under engine cover.

LUBRICATION

To prolong the useful life of your trimmer,

change engine oil as recommended in

this section of Owner's Manual.

IMPORTANT." Do not oil or grease plastic

wheel bearings. Viscous lubricants will

attract dust and dirt that will shorten the

life of the self- lubricating bearings. If you

feel they must be lubricated, use only a

dry, powdered graphite type lubricant

sparingly.

TRIMMER

Always observe safety rules when per-

forming any maintenance.

TIRES

• Keep tires free of gasoline, oil, or insect

control chemicals which can harm rub-

ber.

• Avoid stumps, stones, deep ruts, sharp

objects and other hazards that may

cause tire damage.

TRIMMER LiNE

For best results, replace trimmer lines

when they have worn to half their original

length. Use .155 inch diameter trimmer

line. Cut new trimmer line length to 18-3/4

inches. After new line is installed on

trimmer head, check all lines so they do

not vary more then one (1) inch in length.

This is important to make sure the trim-

mer head is balanced and will not vibrate

abnormally.

_WARNING: Use only the specified

trimmer line. Do not use other materials

such as wire, string, rope, etc. Wire can

break off during trimming and become a

dangerous missile that can cause serious

injury.

TO CUT LiNE TO PROPER LENGTH

NOTE: Trimmer line pre-cut to proper

length is available for this unit; see the

Repair Parts section of this manual.

If trimmer line is purchased in bulk, it must

be cut to 18-3/4 inches before using.

Use the built-in length guage as follows:

1. From front of trimmer, place the end

of spooled trimmer line at the mark on

the side of the debris shield as shown.

2. Wrap trimmer line around front of

chassis cover to other side and cut

at the "22" mark (your unit's width of

cut).

Chassis cover

TO REPLACE TRIMMER LINE

1. Disconnect spark plug wire from spark

plug and place wire where it cannot

come in contact with spark plug.

2. Remove worn trimmer line from line

carrier plate.

3. Fold new, cut to length, trimmer line

in half and insert folded end through

carrier plate opening to back side of

retainer clip.

4. With folded end of line at back side of

retainer clip, pull line outward until line

is fully seated under the retainer clip.

5. Repeat on other side of carrier plate.

6. Check all lines to be sure they are the

same length.

7. Reconnect spark plug wire to spark

plug.

Trimmer

line

Carrier plate

opening

WRAP

LiNE

&ROUND

Debris New

shield End of trimmer

mark spooled line line

Retainer

clip

ENGINE

LUBRiCATiON

Use only high quality detergent oil rated

with API service classification SG-SL.

Select the oil's SAE viscosity grade

according to your expected operating

temperature.

SAE VISCOSITY GRADES

-20 0 30 32 40 60 80 100

-30 -20 -10 0 10 20 30 40

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

NOTE: Although multi-viscosity oils

(5W30, 10W30 etc.) improve starting in

cold weather, these multi-viscosity oils will

result in increased oil consumption when

used above 32°F. Check your engine oil

level more frequently to avoid possible en-

gine damage from running low on oil.

Change the oil after every 25 hours of

operation or at least once a year if the unit

is not used for 25 hours in one year.

Check the crankcase oil level before

starting the engine and after each five (5)

hours of continuous use. Tighten oil plug

securely each time you check the oil level.

TO CHANGE ENGINE OIL

NOTE: Before tipping trimmer to drain oil,

drain fuel tank by running engine until fuel

tank is empty.

1. Disconnect spark plug wire from spark

plug and place wire where it cannot

come in contact with spark plug.

2. Remove engine oil cap; lay aside on a

clean surface.

3. Tip trimmer on its side as shown and

drain oil into a suitable container.

Rock trimmer back and forth to re-

move any oil trapped inside of engine.

Container

4. Wipe off any spilled oil from trimmer or

side of engine.

5. Fill engine with oil (See "ADD Oil" in

the Operation section of this manual).

6. Replace engine oil cap.

7. Reconnect spark plug wire to spark

plug.

AIR FILTER

Your engine will not run properly and

may be damaged by using a dirty air

filter. Replace the air filter cartridge every

1O0 hours of operation or every season,

whichever occurs first. Service air cleaner

more often under dusty conditions.

TO CLEAN AIR FILTER

1. Loosen screw and tilt cover to remove.

2. Carefully remove cartridge.

3. Clean by gently tapping on a flat sur-

face. If very dirty, replace cartridge.

_,CAUTION: Petroleum solvents, such

as kerosene, are not to be used to clean

cartridge. They may cause deterioration

of the cartridge. Do not oil cartridge. Do

not use pressurized air to clean or dry

cartridge.

4. Install cartridge, then replace cover

making sure the tabs are aligned with

the slots in the back plate. Fasten

screw securely.

Lip Back plate

Cartridge

Slot

Cover

Cover tab

MUFFLER

Inspect and replace corroded muffler as it

could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of

each mowing season or after every 100

hours of operation, whichever occurs

first. Spark plug type and gap setting

are shown in the "PRODUCT SPECIFIC-

ATIONS" section of this manual.

CLEANING

iMPORTANT: For best performance,

keep trimmer free of built-up grass and

trash. Clean the underside of your trimmer

after each use.

_CAUTION: Disconnectspark plug wire

from spark plugand place wirewhereit

cannot come in contactwith plug.

o Turntrimmer on itsside. Makesure air

filterand carburetorare up. Cleanthe

undersideof your trimmer byscraping

to removebuild-up of grass andtrash.

Cleanengine oftento keeptrashfrom

accumulating. A clogged engine runs

hotterand shortensengine life.

Keepfinished surfacesand wheelsfree

of all gasoline,oil, etc.

Wedo not recommend usinga gar-

den hoseto cleantrimmer unlessthe

electricalsystem, muffler,air filterand

carburetorare coveredto keepwater

out. Waterin enginecan resultin short-

enedengine life.

• L,WARNING: To avoid serious injury,

before performing any service and

adjustments:

1. Stop engine.

2. Make sure the rotating lines and

all moving parts have completely

stopped.

3. Disconnect spark plug wire from spark

plug and place wire where it cannot

come in contact with plug.

TO REMOVE/REPLACE TRIMMER

HEAD DRIVE BELT

1. Remove screw at front of chassis

cover.

2. Lift cover up and away from trimmer.

3. Remove the two (2) screws on sides of

Screw

TRIMMER

TO ADJUST TRIMMING HEIGHT

See "TO ADJUST TRIMMING HEIGHT" in

the Operation section of this manual.

TO ADJUST HANDLE

The upper handle may be adjusted to dif-

ferent height positions.

• Loosen handle knob only enough to

allow the upper handle to pivot to the

desired position.

• Tighten handle knob securely.

NOTE: The handle knob and bolt may be

reversed for left handed operation.

Upper handle

Chassis

cover

trimmer securing the debris shield.

4. Turn trimmer on its side with carbu-

retor and fuel cap up.

5. Remove the two (2) screws on under-

side of trimmer securing the debris

shield.

6. Slide the debris shield rearward and

remove.

7. Remove belt from engine pulley on

crankshaft.

8. Remove belt from trimmer head pulley.

Eric

pulley

Handle knob

Debris shield screws

9. Note the position of the control cable

and idler return spring, then remove

idler assembly from chassis and re-

move belt and idler from trimmer.

10. Remove belt from idler assembly by

removing bottom belt keeper and idler

pulleys.

11 .Assemble new belt, idler pulleys and

bottom belt keeper to idler bracket.

Tighten pulley bolts securely.

NOTE: Be sure belt is inside top belt

keeper on idler assembly.

12. Position belt and idler assembly in

trimmer, reconnect idler spring and as-

semble idler to chassis.

13. Install belt around trimmer head pulley

and engine pulley.

14. Replace debris shield and tighten the

four (4) screws securely.

15. Replace chassis cover and tighten

screw securely.

Always use Craftsman replacement parts

to assure proper fit and long life.

Engine pulley

Nut

-. s oer/

-.. \

Control cable j '" " "

Belt /_ "-

Idler assembly -.'_< ,,

Top belt keeper _ "

Bolt

Idler bracket

Spacer

Idler

spring

Flatidler

Bottom

., belt

keeper

/ / Flat idler

Trimmer head pulley

ENGINE

ENGINE SPEED

Your engine speed has been factory set.

Do not attempt to increase engine speed

or it may result in personal injury. If you

believe that the engine is running too fast

or too slow, take your unit to a Sears or

other qualified service center for repair

and/or adjustment.

CARBURETOR

Your carburetor has a nonadjustable

fixed main jet for mixture control. If your

engine does not operate properly due to

suspected carburetor problems, take your

unit to a Sears or other qualified service

center for repair and/or adjustment.

IMPORTANT: Never tamper with the

engine governor, which is factory set for

proper engine speed. Overspeeding

the engine above the factory high speed

setting can be dangerous. If you think

the engine-governed high speed needs

adjusting, take your unit to a Sears or

other qualified service center, which has

proper equipment and experience to make

any necessary adjustments.

Immediately prepare your trimmer for stor-

age at the end of the season or if the unit

will not be used for 30 days or more.

TRIMMER

When trimmer is to be stored for a period

of time, clean it thoroughly, remove all dirt,

grease, leaves, etc. Store in a clean, dry area.

1. Clean entiretrimmer (See"CLEANING" in

the Maintenance section ofthis manual).

2. Lubricate as shown in the Mainte-

nance section of this manual.

3. Be sure that all nuts, bolts, screws, and

pins are securely fastened. Inspect

moving parts for damage, breakage and

wear. Replace if necessary.

4. Touch up all rusted or chipped paint

surfaces; sand lightly before painting.

HANDLE

You can fold your trimmer handle for storage.

• Loosen handle knob enough to allow

upper handle to be folded forward.

iMPORTANT." When folding the handle

for storage or transportation, be sure to

fold the handle as shown or you may

damage the control cables.

Handle knob

ENGINE

FUEL SYSTEM

iMPORTANT: It ts important to prevent

gum deposits from forming in essential

fuel system parts such as carburetor, fuel

filter, fuel hose or tank during storage.

Also, alcohol blended fuels (called

gasohol or using ethanol or methanol)

can attract moisture which leads to

separation and formation of acids during

storage. Acidic gas can damage the fuel

system of an engine while in storage.

• Empty the fuel tank by starting the en-

gine and letting it run until the fuel lines

and carburetor are empty.

Never use engine or carburetor cleaner

products in the fuel tank or permanent

damage may occur.

Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable

alternative in minimizing the formation

of fuel gum deposits during storage.

Add stabilizer to gasoline in fuel tank or

storage container. Always follow the mix

ratio found on stabilizer container. Run

engine at least 10 minutes after adding

stabilizer to allow the stabilizer to reach

the carburetor. Do not drain the gas tank

and carburetor if using fuel stabilizer.

ENGINE OiL

Drain oil (with engine warm) and replace

with clean engine oil. (See "ENGINE" in

the Maintenance section of this manual).

CYLINDER

1. Remove spark plug.

2. Pour one ounce (29 ml) of oil through

spark plug hole into cylinder.

3. Pull starter handle slowly a few times

to distribute oil.

4. Replace with new spark plug.

OTHER

• Do not store gasoline from one season

to another.

• Replace your gasoline can if your can

starts to rust. Rust and/or dirt in your

gasoline will cause problems.

• If possible, store your unit indoors and

cover it to protect it from dust and dirt.

• Cover your unit with a suitable protec-

tive cover that does not retain moisture.

Do not use plastic. Plastic cannot

breathe, which allows condensation to

form and will cause your unit to rust.

iMPORTANT: Never cover trimmer while

engine and exhaust areas are still warm.

_I_CAUTION: Never store the trimmer

with gasoline in the tank inside a building

where fumes may reach an open flame

or spark. Allow the engine to cool before

14storing in any enclosure.

TROUBLESHOOTING =See appropriate section in manual unless directed

PROBLEM

Does not start

to a Sears Parts & Repair Center.

CAUSE

1. Dirty air filter.

2. Out of fuel.

3. Stale fuel.

Loss of power

4. Water in fuel.

5. Spark plug wire is

disconnected.

6. Bad spark plug.

7. Throttle control lever not

in correct position

(if equipped).

1. Dirty air filter.

2. Buildup of grass, leaves,

and trash under trimmer.

3. Too much oil in engine.

4. Walking speed too fast.

CORRECTION

1. Clean/replace air filter.

2. Fill fuel tank.

3. Empty fuel tank and refill

with fresh, clean gasoline.

4. Empty fuel tank and refill

with fresh, clean gasoline.

5. Connect wire to spark plug.

6. Replace spark plug.

7. Move throttle lever to FAST

position.

1. Clean/replace air filter.

2. Clean underside of trimmer

and trimmer head.

3. Check oil level.

4. Trim at slower walking

speed.

Excessive 1. Lines uneven or broken. 1. Check trimmer lines.

Vibration 2. Loose nuts or bolts. 2. Check all hardware,

including engine bolts.

3. Damaged trimmer head. 3. Check/repair trimmer head.

Starter rope 1. Bent engine crankshaft. 1. Contact a Sears or other

hard to pull qualified service center.

Loss of head 1. Belt not driving. 1. Put belt on pulleys or

drive replace belt if broken.

Hard to push 1. Handle height position not 1. Adjust handle height

right for you. to suit.

1. Trimmer line length is

too short.

2. Throttle control lever not

in correct position

(if equipped).

Poor trimming

performance

Trimmer head

does not

retain line

1. Trimmer line not

properly installed.

2. Broken line retainer clip.

3. Incorrect size of

trimmer line.

If line is worn or broken to

half of original length,

replace line.

Move throttle lever to FAST

position.

1. Follow instructions in

Maintenance section.

2. Replace string carrier plate

assembly.

3. Use .155 diameter

trimmer line.

10 DE ,ES

Operate a trimmer aoross the fece

of slopes, never up or down slopes.

15 DEGREES

(.O

-r-

Use this guide and do not trim on a slope greater than 15 degrees.

A 10 degree slope is a hill that increases in height at approximately 1.7 feet in 10 feet.

A 15 degree slope is a hill that increases in height at approximately 2.5 feet in 10 feet.

Use extreme care at all times and avoid sudden turns or maneuvers. Follow other instructions in this

manual for safety in trimming on elopes. Operate a trimmer across the face of slopes, never up or down

slopes= Use extra care when operating on or near slopes and obstructions.

Page is loading ...

CRAFTSMAN WEED TRIMMER - - MODEL NUMBER 917,773711

CRAFTSMAN WEED TRIMMER ==MODEL NUMBER g17,773711

KEY PART

NO. NO. DESCRiPTiON

1 - - - Engine, Briggs & Stratton,

Model No. 122T02=1012=B1

(See Breakdown)

2 150406 Bolt, Engine Mounting 3/8-16

3 179466 Pulley, Engine

(Includes Setscrew, Key #4)

8 169821X479 Handle, Lower

9 150078 Screw, Hex Washer Head

5/16-18 x .75

10 169797X479 Handle, Upper

11 170980 Bolt, Handle

12 189713X428 Knob, Handle

15 179751 Handle Adjuster Assembly

16 194788 Guide, Rope

18 66426 Wire Tire

19 176983 Control Bar

20 417238 Throttle Control

21 158755 Screw, Hex Washer Head

22 178700X004 Axle Shaft Assembly

23 150078 Screw, Hex Washer Head

5/16-18 x .75

24 52160 Washer, Axle

26 752063 Wheel, 14 x 2

27 409148 Nut, Hex, Flangelock 3/8-16

28 181699 Drive Control Cable

29 178365 Decal, Warning

30 406678 Decal, Engine Cover

33 132004 Nut, Hex

34 86899X004 Bracket, Upstop

35 750634 Screw, Threaded, Rolled

#10-24 x 5/8

36 851084 Bolt, Hex Head

37 850263 Washer, Lock

38 851074 Washer, Flat, Hardened

39 111190X Clamp, Cable

40 83816 Screw

- - 417701 Owner's Manual

Available accessories

-- 71 33623

-- 71 33000

-- 71 79991

not included with trimmer:

Gas Can (2.5 Gallon Container)

SAE 30W Oil (20 Ounce Bottle)

Trimmer Line

(Pack of 24 strings, .155 dia.)

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm.

IMPORTANT: Use only Original Equipment Manufacturer (O.EM.) replacement parts.

Failure to do so could be hazardous, damage your weed trimmer and void your warranty.

CRAFTSMAN WEED TRIMMER - - MODEL NUMBER 917,773711

52 51 20 44 47 21

17 __

8 23

12 24

4 4O

O_ 31

CRAFTSMAN WEED TRIMMER ==MODEL NUMBER 917,773711

KEY PART

NO. NO.

1 174031X815

2 182219

3 173715

4 185476

5 172145X004

6 166042

7 173716

8 751592

9 166043

10 160829

11 155552

12 173717

13 174719

14 409149

15 173811

16 180268

17 57808

18 178848

19 199574

20 170553

21 149746

22 STD541137

23 STD551137

24 STD551037

25 180340

26 172551

27 174549

28 172520

29 169766X479

30 174543

31 174581

32 173973

33 172519

34 180338

35 182217

36 172516

37 174580

38 172523

39 180334

40 180333

41 174029

43 174042

44 404936

45 174596X479

48 17060408

47 174036

51 189006

52 178848

DESCRIPTION

Chassis Assembly

Line, Trimmer .155 diameter x 18.75 long

Screw, Self-Tapping 5/16-18 x 1

V-Belt

Bracket, idler

Pulley, idler, V-Groove

Bolt, Hex Head 3/8-16 x 1.25

Locknut, Hex 3/8-16

Pulley, idler, Flat

Bolt, Shoulder

Locknut 5/16-18

Spacer

Bolt, Shoulder

Locknut, Flange

Spring, Return

Deflector, Bottom

Screw 1/4-20 x 1/2

Screw #10-24 x 3/4

Belt Keeper

Cover, Chassis, Top

Screw #10-24 x 1-3/4

Nut, Hex 3/8-24 UNF

Washer, Lock 3/8

Washer, Flat 3/8

Pulley, Driven

Spacer, Pulley

Bearing

Jackshaft

Cover, Chassis, Bottom

Spindle Housing Assembly

(* Includes Upper Bearing, Key Number 27)

Ring, Retaining, External, 17mm

Spring, Locking Plate

Locking Plate

Carrier Plate Assembly

Mow Ball Assembly

(Includes Key Numbers 27, 37 and 38)

Cover, Bearing

Ring, Retaining, internal, 40mm

Mow Ball

Bolt, Mow Ball

Spindle Assembly, Complete

(Includes Key Numbers 22-28 and 30-39)

Spacer

Decal, Instruction

Decal, Chassis Cover

Belt Keeper, Bottom

Screw, Self-Tapping

Decal, instruction

Deflector, Rear

Screw

NOTE: All component dimensions given in U.S.inches. 1 inch = 25.4 mm.

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.)replacement parts.

Failureto do so could be hazardous, damage your weed trimmer and void your warranty.

Page is loading ...

Craftsman 917773711 Owner's manual

Brand: Craftsman

Model: 917773711

Category: Garden tools

Type: Owner's manual

This manual is also suitable for

917.773710

Download PDF

report

in other languages

español: Craftsman 917773711 El manual del propietario

Craftsman 917773711 Owner's manual

This manual is also suitable for

Craftsman 917773711 Owner's manual

in other languages

Related papers

Other documents