NEC A3844 User manual

MultiSync

®

IntelliBase

™

USB Hub

User’s Manual

MultiSync

®

IntelliBase

™

USB Hub

User’s Manual

NEC204 Eng.Fr.manual 10/26/98 10:19 AM Page 1

Index

Contents 1

Quick Start 2-15

Controls 16

Specifications 17

Troubleshooting 18

References 19

Limited Warranty 20

Table des matières

Contenu 23

Démarrage rapide 24-37

Commandes 38

Caractéristiques 39

Dépannage 40

Références 41

Garantie limitée 42

NEC204 Eng.Fr.manual 10/26/98 10:19 AM Page 2

Safety Precautions and Maintenance

FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN

SETTING UP AND USING THE MULTISYNC

®

INTELLIBASE

™

WITH USB HUB:

Read Instructions — All the safety and operating instructions should be read before the appliance is operated.

Retain Instructions — The operating instructions should be retained for future reference.

Heed Warning — All warnings on the appliance and in the operating instructions should be adhered to.

Follow Instructions — All operating and use instructions should be followed.

Water and Moisture — The appliance should not be used near water – for example, near a bathtub, washbowl, kitchen

sink, laundry tub, in a wet basement, or near a swimming pool, etc.

Outdoor Use — Warning: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

Location — The appliance should be installed in a stable location. Do not use the monitor while the base is removed.

Ventilation — The appliance should be situated so that its location or position does not interfere with its proper ventilation.

For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation

openings; or placed in a built-in installation, such as a closed bookcase or cabinet that may impede the flow of air through

the ventilation openings.

Heat — The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other

appliances (including amplifiers) that produce heat.

Power Sources —

Use the supplied AC adapter. The appliance should be connected to a power supply only of the type

described in the operating instructions or as marked on the appliance.

Power-Cord Protection — Power-supply cords should be routed so that they are not likely to be walked on or pinched by

items placed upon or against them. Pay particular attention to cords at plugs, convenience receptacles, and the point where

they exit from the appliance.

Grounding or Polarization — Precautions should be taken so that the grounding or polarization means of an appliance

is not defeated.

Cleaning — The appliance should be cleaned only with a polishing cloth or a soft dry cloth. Never clean with furniture wax,

benzine, insecticides or other volatile liquids since they may corrode the cabinet.

Non-Use Periods — The power cord of the appliance should be unplugged from the outlet when left unused for a long

period of time.

Object and Liquid Entry — Care should be taken so that objects do not fall and liquids are not spilled into the enclosure

through openings.

Damage Requiring Service — The appliance should be serviced by qualified service personnel when:

• The power-supply cord or the plug has been damaged.

• Objects have fallen, or liquid has been spilled into the appliance.

• The appliance has been exposed to rain.

• The appliance does not appear to operate normally or exhibits a marked change in performance.

• The appliance has been dropped or the enclosure damaged.

Servicing — The user should not attempt to service the appliance. Servicing should be referred to qualified service personnel

or returned to the dealer or call the NEC TECH service line for assistance at 1-800-632-4662.

The lightning flash with arrowhead, within an

equilateral triangle, is intended to alert the

user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

CAUTION: TO PREVENT THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE COVER

(OR BACK). NO USER- SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in

the literature accompanying the appliance.

IMPORTANT

NEC204 Eng.Fr.manual 10/26/98 10:19 AM Page 3

The FCC Wants You to Know

1. Use the attached specified cable with the MultiSync IntelliBase so as not to interfere with

radio and television reception.

Please use the supplied power cable or equivalent to ensure FCC compliance.

2. This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

a) Reorient or relocate the receiving antenna.

b) Increase the separation between the equipment and receiver.

c) Connect the equipment to an outlet on a circuit different from that to which the receiver

is connected.

d) Consult the dealer or an experienced radio/TV technician for help.

If necessary, the user should contact the dealer or an experienced radio/television technician

for additional suggestions. The user may find the following booklet, prepared by the Federal

Communications Commission, helpful: “How to Identify and Resolve Radio-TV Interference

Problems.” This booklet is available from the U.S. Government Printing Office, Washington,

D.C., 20402, Stock No. 004-000-00345-4

Connecting the Power Cord

AC Wall Socket

Long slot

is neutral

(ground) side.

Insert the wide

blade into the

ground side slot.

CAUTION: To prevent electric shock do not

use this (polarized) plug with an extension

cord, receptacle or other outlet unless the

blades can be fully inserted to prevent blade

exposure.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS APPLIANCE

TO RAIN OR MOISTURE.

NEC204 Eng.Fr.manual 10/26/98 10:19 AM Page 4

1

MultiSync

®

IntelliBase

™

USB Hub

User's Manual

User’s

Manual

Contents

Your new NEC Technologies MultiSync

®

IntelliBase

™

USB Hub

carton box* should contain the following:

• MultiSync IntelliBase USB Hub (IB-USB)

• AC Adapter • Adapter Plate A

• User’s Manual • Adapter Plate B

• Registration Card

• USB Cable

• Screws

AC Adapter

*Remember to save your original box and packaging

material to transport or ship the MultiSync IntelliBase USB Hub.

Note: You can register your product on the Internet at

http://www.prodreg.com/nec

Registration

Card

— Important —

To help us in our continuing efforts to

better serve and support you, and to bring

you new and innovative products, please

take a few moments to register your new

NEC MultiSync monitor.

By returning this card, we confirm your

date of purchase and records the model

and serial numbers. This facilitates our

ability to process warranty claims,

especially if your original proof of

purchase is lost.

Thank you for your time and for

choosing an NEC MultiSync monitor.

THANK YOU FOR

CHOOSING AN NEC

MultiSync

®

IntelliBase

™

PRODUCT REGISTRATION

NEC MultiSync Monitors

MultiSync

IntelliBase

USB Hub

USB Cable

Screws

Adapter

Plate B

Adapter

Plate A

NEC204 Eng.Fr.manual 10/26/98 10:20 AM Page 5

2

Quick Start

How to attach IntelliBase

™

USB Hub to your

MultiSync

®

brand monitor

THE INTELLIBASE USB HUB WILL ONLY WORK WITH THE MULTISYNC

BRAND MONITORS LISTED BELOW. DO NOT ATTEMPT TO CONNECT

THE INTELLIBASE WITH ANY OTHER MONITOR BRANDS.

MAKE SURE THE MONITOR IS DISCONNECTED FROM THE SYSTEM

AND IS UNPLUGGED FROM THE WALL OUTLET BEFORE ANY

WORK IS DONE ON THE MONITOR.

FOR 21-INCH MONITORS, IT IS ADVISED THAT TWO PEOPLE ARE

INVOLVED DURING THE ENTIRE INSTALLATION PROCESS.

To attach the IntelliBase to your MultiSync brand monitor, the original base

must first be removed. Depending on the model of your MultiSync brand

monitor, the removal procedure of the original base and the attachment of

the IntelliBase will vary. Locate the model name (located in the lower right

corner of your monitor’s bezel) of your MultiSync brand monitor in the table

below. Follow the removal procedure to detach the original base from your

monitor using the diagrams on the following pages and attach the

IntelliBase to your monitor.

MultiSync Monitor Model Names

Original Monitor Base

Removal and IntelliBase

Installation Instructions

MultiSync 50, MultiSync 70, XV15 and

XV15+

MultiSync XE15, XE17, XP15, XP17, XV17,

XV17+, A500, A500+, A700, A700+,

A900, E500, E700, E900, E900+, M500,

M700 and P750

MultiSync XE21, XP21, E1100, E1100+,

P1150 and P1250+

Page 3

Page 5

Page 7

NEC204 Eng.Fr.manual 10/26/98 10:20 AM Page 6

3

Step 2 Using a Phillips screwdriver, remove the screw securing the original

base to the monitor as shown in Figure 2A. Remove and save the

original base for possible future use.

Note: Do not remove the spindle or swivel plate.

Figure 2A

MultiSync

®

Monitor Model Names

MultiSync 50, MultiSync 70, XV15 and XV15+

Step 1 With the monitor

unplugged from your

system and the wall

outlet, carefully

turn the monitor

upside down on

a firm table so that

the base is facing

up as shown

in Figure 1.

Figure 1

MONITOR IN POSITION TO

REMOVE THE BASE AND ATTACH

INTELLIBASE USB HUB

BASE

SWIVEL

PLATE

SPINDLE

DO NOT REMOVE SPINDLE OR

SWIVEL PLATE

BASE

NEC204 Eng.Fr.manual 10/26/98 10:20 AM Page 7

Step 4 Locate the two

screws that are

supplied with

the IntelliBase

and attach the

IntelliBase to

the adapter plate

and monitor

as shown

in Figure 2C.

Proceed to Page 10 to connect your MultiSync

®

monitor with the IntelliBase

USB Hub to your system.

4

Figure 2C

Step 3 Locate Adapter

Plate “A” that

is supplied with

the IntelliBase

™

and secure it to

the spindle using

the screw that

was removed

in Step 2

as shown in

Figure 2B.

Figure 2B

GUIDE SPINDLE

THROUGH CENTER

HOLE ON ADAPTER

PLATE (A)

ADAPTER

PLATE (A)

SPINDLE

INTELLIBASE

(BOTTOM VIEW)

ROTATE ADAPTER

PLATE UNTIL IT

ALIGNS WITH

THROUGH HOLES

ON THE BASE

NEC204 Eng.Fr.manual 10/26/98 10:20 AM Page 8

5

MultiSync

®

Monitor Model Names

MultiSync XE15, XE17, XP15, XP17, XV17, XV17+, A500, A500+ A700,

A700+, A900, E500, E700, E900, E900+, M500, M700 and P750

Step 1 With the monitor

unplugged from your

system and wall

outlet, carefully

turn the monitor

upside down on

a firm table so that

the base is facing

up as shown

in Figure 1.

Step 2 Using your thumbs, push on the locking tabs while pulling forward

and up as shown by the directional arrow in Figure 3A. This

action releases the base from the monitor. Remove and save the

original base for possible future use.

Figure 3A

Figure 1

MONITOR IN POSITION TO

REMOVE THE BASE AND ATTACH

INTELLIBASE USB HUB

BASE

LOCKING

TABS

NEC204 Eng.Fr.manual 10/26/98 10:20 AM Page 9

6

Step 3 Using a Phillips

screwdriver, remove

the screw securing

the two base halves

together as shown

in Figure 3B.

Retain the screw

and black nylon

washer for use

in the next step.

Figure 3B

ORIGINAL MOUNTING

RETAIN

THESE

PARTS TO

USE IN

NEW

MOUNTING

Step 4 Locate Adapter Plate “B”

that is supplied with

the IntelliBase

™

and

secure it to the spindle

using the screw and

black nylon washer that

was removed in Step 2

as shown in Figure 3C.

BASE

ADAPTER

PLATE (B)

NEW MOUNTING

Figure 3C

Step 5 After the adapter plate has

been attached to the base,

snap the base assembly to

the monitor. To accomplish

this, position all the locking

tabs on the base so they

mate with the holes in the

monitor. Slide the base

assembly in place as

shown in Figure 3D.

Figure 3D

NEC204 Eng.Fr.manual 10/26/98 10:20 AM Page 10

Step 6 Locate the two

screws that

are supplied

with the

IntelliBase

™

and attach

the IntelliBase

to the adapter

plate and

monitor as

shown in

Figure 3E.

Proceed to Page 10 to connect your MultiSync

®

monitor with IntelliBase

USB Hub to your system.

7

MultiSync Monitor Model Names

MultiSync XE21, XP21, E1100, E1100+, P1150 and P1250+

Step 1 With the monitor

unplugged from your

system and wall outlet,

carefully turn the

monitor upside down

onto a firm table so

that the base is

facing up as shown

in Figure 1.

Figure 1

MONITOR IN POSITION TO

REMOVE THE BASE AND ATTACH

INTELLIBASE USB HUB

BASE

Figure 3E

INTELLIBASE

(BOTTOM VIEW)

ROTATE ADAPTER

PLATE UNTIL IT

ALIGNS WITH

THROUGH HOLES

ON THE BASE

NEC204 Eng.Fr.manual 10/26/98 10:20 AM Page 11

8

Step 2 Using a Phillips screwdriver, remove the three screws securing

the original base to the monitor. Remove the base by sliding and

lifting as shown in Figure 4A. Save these screws for use in

Steps 6 and 7. Save the original base for possible future use.

Figure 4A

Step 3 Using a Phillips

screwdriver, remove

the screw securing

the two base

halves together

as shown in

Figure 4B.

Retain the screw

and black nylon

washer for

use in the next step.

Figure 4B

ORIGINAL MOUNTING

RETAIN

THESE

PARTS TO

USE IN

NEW

MOUNTING

Step 4 Locate Adapter Plate “B”

that is supplied with

the IntelliBase

™

and secure

it to the spindle using the

screw and black nylon

washer that was removed

in Step 3 as shown in

Figure 4C.

BASE

ADAPTER

PLATE (B)

NEW MOUNTING

Figure 4C

NEC204 Eng.Fr.manual 10/26/98 10:20 AM Page 12

9

Step 5 After the adapter plate

has been attached to

the base, snap the base

assembly to the monitor.

To accomplish this, position

all the locking tabs on

the base so they mate

with the holes in the

monitor. Slide the base

assembly in place as

shown in Figure 4D.

Figure 4D

Step 6 Using two of the

screws that were

removed in Step 2,

attach the adapter

plate assembly to

the monitor. To

accomplish this, it

will be necessary

to turn the adapter

plate fully counter-

clockwise while sliding it

forward as shown in Figure 4E. This will allow you to install the

two rear screws.

Figure 4E

Step 7 Using the remaining screw

that was removed in Step 2,

complete attachment of the

adapter plate assembly. To

accomplish this, it will

be necessary to slide

the adapter plate backwards

as shown in Figure 4F.

Figure 4F

NEC204 Eng.Fr.manual 10/26/98 10:20 AM Page 13

10

Step 8 Locate the two

screws that are

supplied with

the IntelliBase

™

and attach the

IntelliBase to

the adapter plate

and monitor

as shown in

Figure 4G.

Proceed below to connect your MultiSync

®

monitor with the IntelliBase USB

Hub to your system.

Figure 5

Step 1 Having successfully

installed your new

IntelliBase, carefully

turn the monitor

right side up

as shown in

Figure 5.

How to connect your MultiSync monitor with

IntelliBase USB Hub to your system

Figure 4G

INTELLIBASE

(BOTTOM VIEW)

ROTATE ADAPTER

PLATE UNTIL IT

ALIGNS WITH

THROUGH HOLES

ON THE BASE

NEC204 Eng.Fr.manual 10/26/98 10:20 AM Page 14

11

Step 2 Connect one end of the supplied USB cable to the USB input jack

on the rear of the IntelliBase

™

(Detail B) and the other end to the

USB output jack of your computer system (Detail A) as shown in

Figure 6.

Figure 6 – REAR VIEW

Step 3 Connect one

end of the

supplied

AC adapter

to the DC

input jack

on the rear

of the

IntelliBase

and the other

end into any

110-120V

AC wall outlet as

shown in Figure 7.

NOTE: The IntelliBase front green LED power indicator should be on

after this step.

Figure 7

Step 4 Reconnect your MultiSync

®

monitor to your computer system as

shown in the monitor user’s manual.

USB

OUTPUT

SEE

DETAIL A

DETAIL B

SEE

DETAIL B

AC ADAPTER

NEC204 Eng.Fr.manual 10/26/98 10:20 AM Page 15

12

Note: Steps 5-11 describe USB driver installation for the

Windows

®

98 operating system. Other operating systems which

support USB may follow a different procedure.

Step 5 Turn your computer on. The computer will automatically recognize

your IntelliBase

™

. The Add Hardware Wizard will search

for, locate and install the USB Controller and Hub Device drivers

needed by the IntelliBase.

Step 6 Click on Next > button to begin driver installation.

NEC204 Eng.Fr.manual 10/26/98 10:20 AM Page 16

13

Step 7 Select Search for the best driver for your device and then click

the Next > button.

Step 8 Click Next > button to select default driver location.

NEC204 Eng.Fr.manual 10/26/98 10:20 AM Page 17

Step 9 Click on Next > button to install drivers. The Hardware

Wizard will copy the necessary files and install the drivers.

14

Step 10 Insert the Windows

®

98 CD-ROM and then click OK. The

required files are copied from the Windows 98 CD-ROM.

NEC204 Eng.Fr.manual 10/26/98 10:20 AM Page 18

15

Step 11 The software has been successfully loaded and you are

now ready to use your IntelliBase

™

.

NEC204 Eng.Fr.manual 10/26/98 10:20 AM Page 19

16

Controls

POWER: Indicator light illuminates when power is applied to the

IntelliBase

™

USB Hub.

USB: Indicator light illuminates when the IntelliBase is connected to a computer

with an active USB port.

USB INPUT JACK: This connection provides bi-directional communication

with the host computer using the USB cable provided with the IntelliBase.

USB OUTPUT JACK: Can be connected to virtually any USB device using

a standard USB cable terminated with a Series A plug. Includes both high

and low speed and high and low power USB devices.

NOTE: All four USB output jacks are identical and may be used interchangeably.

POWER

USB

OUTPUT JACKS

USB

INPUT JACK

DC

INPUT JACK

NEC204 Eng.Fr.manual 10/26/98 10:20 AM Page 20

Page is loading ...

NEC A3844 User manual

This manual is also suitable for

NEC A3844 User manual

in other languages

Related papers

Other documents