Cashino CSN-80V User manual

CSN-80V User manual

1

CSN-80V Thermal Receipt printer

Protocol: Lin Xiaopeng 2017.04.06

Audit : Hu Riyu 2017.04.08

Standardize：Liu Zhonghua 2017.04.09

Authorize: Wang Huanyong 2017.04.11

CSN-80V User manual

2

Company: Xiamen Cashino Technology Co., Ltd.

Tel: 0592-5517253 Fax: 0592-5231815

Address: 4/F,No.318,Tongji South Road, Jimei

District,Xiamen,China.361021

The manual is subject to change without further notice. Please contact Xiamen Cashino

Technology Co., Ltd. directly for the latest version.

revision record

Item

Date

Description

Edited

page

Desing

Review

1

20170406

The first draft

Lin

Xiaopeng

Hu Riyu

www.cashinotech.

CSN-80V User manual

3

Contents

1.Introduction.....................................................................................................................................7

1. 1 Unpacking.......................................................................................................................... 7

1.2 Name of each part of the printer..................................................................................... 7

2. Specifications................................................................................................................................8

3. Basic operation and usage.........................................................................................................8

3.1 open the paper bin cover..................................................................................................8

3.2 install the paper roll........................................................................................................... 9

3.3 set the printing mode (DIP switch)................................................................................10

3.4 Control panel.................................................................................................................... 10

3.5 self-test.............................................................................................................................. 11

3.6 printer connection POS80V interfaces: serial+USB+ Ethernet............................... 11

3.6.1 Serial interface:.....................................................................................................11

3.6.2 USB interface:.......................................................................................................12

3.6.3 Ethernet interface:................................................................................................12

4. Printer fault analysis.................................................................................................................. 12

4.1 Paper jam inclusion.........................................................................................................12

4.2 printer cleaning................................................................................................................ 13

5．Command Introduction............................................................................................................14

5.1 Command List.................................................................................................................. 14

5.2 Commands details...........................................................................................................16

①Printing and paper feed commands........................................................................16

Printing and paper feed.................................................................................................16

Enter................................................................................................................................. 17

Print and paper feed dots............................................................................................. 17

Print and paper feed n line........................................................................................... 17

②Printing set commands..............................................................................................18

Set print position.............................................................................................................18

Character right space setting....................................................................................... 18

Set line space as n dots................................................................................................18

Set horizontal and vertical movement units...............................................................19

Set line space to default................................................................................................19

Set character print font..................................................................................................20

Set character printing method......................................................................................20

Set character size.......................................................................................................... 21

Set、remove white printing.......................................................................................... 21

Set、remove underline................................................................................................. 22

Set、remove bold print................................................................................................. 23

Set、remove overlapping............................................................................................. 23

Set、cancel characters upside down......................................................................... 23

Set、remove 90°revolving printing............................................................................. 24

Allow、orbid key switch................................................................................................ 24

Set the left margin..........................................................................................................25

CSN-80V User manual

4

Set relative printing position......................................................................................... 25

Set printing alignment....................................................................................................26

Select、cancel user customized characters............................................................. 26

Define user customized characters.............................................................................26

Cancel user customized characters............................................................................29

Set / remove quadruple angle of Chinese print........................................................ 29

Set the Angle of Chinese character word space.......................................................30

Set up the Chinese characters to print mode combination.....................................30

Set Chinese mode......................................................................................................... 31

Exit Chinese character mode.......................................................................................31

Set and cancel under line of Chinese character mode............................................31

Selecting international character set...........................................................................32

Select character code....................................................................................................33

③Graphic printing command....................................................................................... 34

Fill Graphics vertical module data............................................................................... 34

Print Graphics horizontal module data....................................................................... 36

Define downloaded bitmap...........................................................................................37

Print downloaded bitmap.............................................................................................. 38

Define NV bitmap........................................................................................................... 39

Print NV bitmap.............................................................................................................. 42

Print bitmap..................................................................................................................... 43

Print MSB bitmap........................................................................................................... 44

④Tab Commands.......................................................................................................... 45

Horizontal tab..................................................................................................................45

Horizontal tab position setting......................................................................................46

⑤One-dimension bar code command........................................................................47

1D bar code readable character(HRI) print position setting................................... 47

1D bar code readable character(HRI)font type selection........................................47

1D bar code height setting............................................................................................47

1D bar code width setting............................................................................................. 48

1D bar code printing...................................................................................................... 48

⑥Two-dimensional bar code commands..................................................................53

Mode type of QR code.................................................................................................. 53

Setting error correction level of QR code...................................................................54

Store QR code data to QR code data buffer............................................................. 54

Printing QR code............................................................................................................55

Setting QR code graph information.............................................................................55

Printing two dimensional code..................................................................................... 56

Printing two dimensional code..................................................................................... 57

Printing double QR code...............................................................................................58

⑦Status querying Commands.....................................................................................59

Transmission status....................................................................................................... 59

Transit the printer status to host.................................................................................. 60

CSN-80V User manual

5

Transit printer ID.............................................................................................................60

Select peripherals.......................................................................................................... 61

Real-time transmission status......................................................................................62

Real-time pulse...............................................................................................................66

⑧Commands in page print mode............................................................................... 67

Forms feed...................................................................................................................... 67

Data print in page print mode.......................................................................................67

Page print mode select................................................................................................. 67

Line print mode select................................................................................................... 68

Character development angle select in page print mode....................................... 68

Page print mode print area setting..............................................................................69

Vertical absolute position setting in page print mode.............................................. 70

Vertical relative position setting in page print mode.................................................71

Printer reset.....................................................................................................................71

Print self-test page......................................................................................................... 72

paper cut..........................................................................................................................72

Full cut..............................................................................................................................73

Partial cut.........................................................................................................................73

Specified pulse generation........................................................................................... 73

Setting up paper type.................................................................................................... 74

Feed to the beginning of the next label...................................................................... 74

CSN-80V User manual

6

PREFACE

It is very honor to cooperate with you. Before using the printer, please read this

user manual carefully, in order to properly use and better show the characteristics of this

Printer.

CAUTIONS

1. The printer should be installed in stable place to avoid vibration and impact.

2. Do not use and store printers in high humidity and dirty places.

3. Connect the power adapter of the printer to an appropriate grounding socket to avoid

using the same socket with a large motor or other device that can cause a power supply

voltage fluctuation.

4. Avoid water or conductive material (such as metal) inside the printer and turn off the

power as soon as it occurs.

5.If the printer is not used for a long time, please disconnect the power of the printer power

adapter.

6.The user shall not remove the printer for repair or modification without authorization.

7.The power adapter uses only a random power adapter that specially designed for.

8. In order to guarantee the quality and the life of the printer, it is recommended to use

high-quality printing paper in priority.

APPLICATIONS

1.Print POS system receipts.

2.Print EFT POS system receipts.

3.Print Gym, Post, Hospital, Civil Aviation system receipts.

4.Print inquiry, service system receipts.

5.Print instrument test receipts.

6.Print tax,tab receipts.

CSN-80V User manual

7

1.Introduction

1. 1 Unpacking

While open, make sure that the following parts are present and not damaged in

transportation.If have any question, please contact the supplier immediately!

1.2 Name of each part of the printer

CSN-80V User manual

8

⑴Power ⑵Key for opening the top cover ⑶control panel

⑷paper out mouth ⑸Top cover/paper cover ⑹printer case ⑺Functional dial

code switch cover ⑻Adjustment cover of cutter ⑼USB port ⑽Serial port（DB9）

⑾Lan port（RJ45） ⑿Cashdrawer port（RJ11）⒀DC outlet（DIN-3P）

2. Specifications

Printing

Printing method

Thermal printing

Printing speed

Max:250mm/s

Resolution

8dots/mm

Printing width

72mm

Character

Character set

ANK：12*24

GBK：24*24

Character font

ANK：(9*17,12*24)

Paper roll

Paper typr

Thermal paper

Paper width

80±0.5mm

Paper roll diameter

max：83mm

Paper thickness

50-80μm

Reliablity

MCBF

15 million lines

TPH

>100km

Cutter life

>1 million cuts

Interfaces

Serial

port/USB/LAN/Cashdr

awe

Serial

port/USB/Cashdr

awer

Command

ESC/POS compatible command sets

Cutter type

Full cutter/Partial cutter

Cashdrawer control

24V/1A （support 12V and 24V

cashdrawer）

Power supply

DC24V /2A

Dimensions (width * depth * height)

88*87*57mm

Environment

Operating temp

0°C ~ 50°C

Operating Humidity

20% ~ 85%RH

Storage temp

-20°C ~ 60°C

Storage Humindity

5% ~ 90%RH

3. Basic operation and usage

3.1 open the paper bin cover

When the printer needs to change the paper, the paper cover must be opened. When it is

CSN-80V User manual

9

opened, please press the open button on the left of the printer with your finger and press

down slightly to make the paper cover bounce up. Then, hold the paper cover with your

hand and flip it backwards.(see as image 1)

1

3.2 install the paper roll

Please use the correct type of paper roll.

1. Power off the printer;

2. Open the top cover(paper cover),

3. Take out the used up paper roll,(skip this step if the printer unused before),

4. install the new paper roll as shown in image 2,

5. Pull the paper out of the paper mouth;

6. Gently close the paper cover and buckle it in place.

2

CSN-80V User manual

10

3.3 set the printing mode (DIP switch)

From setting the DIP switch can change the cutter, language, speed, buzzer, printing

density and other settings mode of the printer.

ON-OF

F

Function

ON

OFF

1

cutter

No cutter

Have cutter

2

Beep reminder

close

open

3

Printing density

High

density

Normal density

4

/

5

characters per

line printed

64

48

6

/

7-8

Transmission speed (only useful to serial port )

- baud rate

SW7

SW8

Transmission speed（bps）

-bits/sec

ON

9600

ON

OFF

19200

OFF

ON

38400

OFF

115200

Note: language and baud rate can be setted via printer setting tool.

3.4 Control panel

CSN-80V User manual

11

⑴ Feed

Press this key to feed the paper. Press this key continuously to keeping feeding the

paper .

⑵ Paper

If both the light and Error light are on at the same time, the printer is run out of paper; if

both the light and Error light are off, the printer has paper.

⑶ Power

This light on means the printer power on, this light off means the printer power off.

⑷ Error

When the printer is out of paper, cutter error, printed head overheated and other errors

occurs, lights flashing.

3.5 self-test

After the printer is connected, power off the printer firstly, and then press the Feed button

and power on of the printer simultaneously. After about 2 seconds, release the button and

the printer will print out the current status and printer Settings.

3.6 printer connection

POS80V interfaces: serial+USB+ Ethernet

3.6.1 Serial interface:

1) Data transmission mode: serial

2) Synchronous mode: asynchronous

3) Handshake signal: DTR / DSR or XON / XOFF control mode

4) Bit rate: .115200,57600,38400, 19200, 9600, 4800 the BPS is optional.

5) Word size: 8

6) Parity: no parity, odd parity, even parity optional.

7) Stop Bits: 1

8) Enter the polarity of the information:

Symbol (MARK) = logic 1 (-3 to-15VDC)

Space (SPACE) = logical 0 (+3 to +15 VDC)

CSN-80V User manual

12

Interface cable that along with the printer could be connected with the computer's

serial port.

3.6.2 USB interface:

1) USB outlet: type B.

2) With WINDOWS95/98, need to install the driver (the CD-ROM); with

WINDOWS2000,

XP, NT, do not need to install the driver.

3.6.3 Ethernet interface:

1) Need use setting software that are along with the printer to set IP address of the

printer (192.168.1.87)

same as the IP of your computer when use Ethernet interface.

2) The setup software, refer to the CD’s documentation.

4. Printer fault analysis

4.1 Paper jam inclusion

CSN-80V User manual

13

In the process of using the printer, if you come across the phenomenon of paper jam,

please stop printing in time and power off the printer. The paper jam is usually caused by

the failure of the automatic cutting cutter head to fully back into the body of the paper

cutter after the paper cutting.

When the phenomenon of paper jam occurs, it usually causes paper cover to be unable to

open normally. At this time, please do not forcibly open the cover to avoid damaging to the

printer.

The paper jam exclusion method is as follows:

1. Power off the printer and remove all connecting wires connected to the printer;

2. Pull out the paper cutter cover horizontally and forward as shown in image 4;

3. Rotate the cutter wheel with your finger to rewind the cutter head into the cutter body;

4. Press the "paper cover switch" button vertically downward to open the paper cover and

remove paper jam;

5. If the printing and paper out are normal, then reinstall the paper cutter cover.

4.2 printer cleaning

When one of the following situations occurs to the printer, the print head should be

cleaned:

4.2.1 printing is not clear;

4.2.2 The printed page for a column is not clear;

4.2.3 The paper is making a lot of noise.

The cleaning steps of the print head are as follows:

(1) Power off the printer, open the top cover, if there is paper, remove it;

(2 If you have just finished printing, wait for the print head to cool completely;

(3) with a soft cotton cloth dipped in anhydrous ethanol (should be wring dry) wipe off the

print head of the thermal sensor surface dust, stains;

(4) wait for anhydrous ethanol completely volatilization, close the cover, retry printing.

Note:

1 daily maintenance of printers must ensure that the power supply is turned off;

2 do not touch the surface of the print head with your hands and metal objects, do not use

tweezers and other tools to scratch the print head, printing cots and sensor surface;

3 can not use gasoline, acetone and other organic solvents;

4 wait for anhydrous ethanol completely evaporated, then turn on the power supply to

continue to print.

CSN-80V User manual

14

5．Command Introduction

5.1 Command List

ESC Command

ESC !

Set character printing method

ESC - n

Set and delete underline

ESC E n

Set and delete bold printing

ESC G n

Set and deleteoverlapping printing

ESC｛n

Set and delete inversion printing

ESC V n

Set and delete 90°rotate printing

ESC 1

Set line space n dots(same as ESC3）

ESC 2

Set default line space

ESC 3

Set line space n dots

ESC *

Bitmap vertical modulus data fillings

ESC d

Print and paper feed n lines

ESC % n

Choose and delete customized characters

ESC &

Define customized characters

ESC ? n

Delete customized character

ESC R n

International character sets

ESC t n

Select the character code page

ESC D

Set horizontal tabulation position

ESC J

Print and paper feed n dots

ESC p

Produce cashdrawer pulse

ESC c 5 n

Allow or prohibit to switch printer by button

ESC C

Undefined

ESC T n

Set printing direction in page print mode

ESC u

Peripheral device statustransmission

ESC v

Printer status transmission

ESC i

Full cuts

ESC @

Printer reset

ESC =

Select peripheralsdevice

ESC a

Setting position alignment mode

ESC $ nL nH

Set absolute print position

ESC \ nL nH

Set relative print position

ESC W

Page print mode print area setting

ESC L

Page print mode select

ESC S

Line print mode select

ESC FF

Data print in page print mode

ESC SP n

Character rightspace setting

ESC Z

Two-dimension Bar Code print

ESC M n

Set character print font

CSN-80V User manual

15

ESC m

Partly cuts

ESC q

Undefined

ESC Q

Undefined

GS Command

GS ! n

Set character size

GS *

Define download bitmap

GS / m

Print download bitmap

GS ：

Start or end macro definition

GS ^ r t m

Run macros

GS V m

Choose cut mode and cut

GS P x y

Set horizontal and vertical movement units

GS I n

Printer ID transmission

GS B n

Set and delete white printing

GS b

Undefined

GS H

Set 1-D barcode readable character(HRI)

print position

GS f n

Set HRI character

GS h

Set 1-D barcoe hight

GS w

Set 1-D barcode width

GS k

1-D barcode

GS L nL nH

Set left margin amount

GS a n

Allow or prohibit to upload the status automatically

GS r n

Transmission status

GS v

Transfer printer status to host

GS v 0

Bitmap horizontal modulus data print

GS (

2-D barcode print

GS $nL nH

Vertical absolute position setting in page print mode

GS \ nL nH

Vertical relative position setting in page print mode

FS Command

FS ！n

Kanji printing mode stored setting

FS &

Set Chinese character mode

FS .

Delete Chinese character mode

FS q

Define NV bitmap

FS p n m

Print NV bitmap

FS W n

Kanji quadruple size printing specification/

cancellation

FS – n

Set and delete kanji characterunderline

FS S n1 n2

Kanji character space Setting

FS 2

Undefined

FS A

Undefined

CSN-80V User manual

16

US Command

US Q

Print double QR CODE

US A

Set paper type

DLE Command

DLE EOT n

Real-time transmission status

DLE ENQ n

Real-time request

DLE DC4 fn m t

Real- time pulse

DC2 command

DC2T

Printing self-test page

DC2 *

Print bitmap

DC2 V

Print MSB bitmap

DC2 v

Print LSB bitmap

LF

Line feed

CR

Enter

FF

Forms feed

HT

Horizontal tab

SO

Paper feed to initial position at the next label

5.2 Commands details

①Printing and paper feed commands

Printing and paper feed

Name

print and paper feed

Code

ASCII ：LF

DEC ：10

HEX ：0A

Function

Print the buffer contest,and set the paper feed as per line space,then

adjust

print position to initial position at the next line.

Range

None

Default

None

Notes

None

Example

None

CSN-80V User manual

17

Enter

Name

Enter

Code

ASCII ：CR

DEC ：13

HEX ：0D

Function

Adjust print position to initial position of the same line.

Range

None

Default

None

Notes

After executing, R command, the new printing data will cover old data in

theprinting buffer.

Example

None

Print and paper feed dots

Name

Print and paper feed n dots

Code

ASCII ：ESC J n

DEC ：27 74 n

HEX ：1B 4A n

Function

Print the buffer content and paper feed

Range

0 ≤ n ≤ 255

Default

None

Notes

Paper feed n dots when printing buffer is empty.

After executing this command,printing position is moved to initial

Example

1b 40 30 31 32 1b 4a 10

Print and paper feed n line

Name

Print and paper feed n lines

Code

ASCII ：ESC d n

DEC ：27 100 n

HEX：1B 64 n

Function

Print the contents in printing buffer and paper feed n lines.

Range

0 ≤ n ≤ 255

Default

None

Notes

Print this command set as initial position of the same line

Example

1b 40 30 31 32 1b 64 01

CSN-80V User manual

18

②Printing set commands

Set print position

Name

Set print position

Code

ASCII ：ESC $ nL nH

DEC ：27 36 nL nH

HEX ：1B 24 nL nH

Function

Set left side blank area as（nL + nH × 256）dots

Range

0 ≤ nL ≤ 255

0 ≤ nH ≤ 255

Default

None

Notes

Set left side blank area as[(nL+nH*256)]*0.125mm]

This command is only effective with the initial position of the line.

This command is unavailable if it sets beyond the printing area.

Example

None

Character right space setting

Name

Character right space setting

Code

ASCII ：ESC SP n

DEC ：27 32 n

HEX ：1B 20 n

Function

Character right space setting as (n*0.125mm)

Range

0 ≤ n ≤ 255

Default

n = 0

Notes

When characters double width,Character right space is twice of

normal.When characters amplified,Character right space is n

times of normal.

This command doesn’t affect the setting of Chinese characters.

This command sets the standard values independently in each

mode.

Example

None

Set line space as n dots

Name

Set line space as n dots

Code

ASCII ：ESC 3 n

DEC ：27 51 n

HEX ：1B 33 n

Function

Set line space as n dots

Range

0 ≤ n ≤ 255

Default

n = 33

Notes

Line space as below:

CSN-80V User manual

19

If the line space settedis less than the highest character in that line,then

this line space is equal to the height of the highest character.

If ESC2,ESC@,reset the printer, the printer blackout,and the line

spaceturns to default.

Example

1b 40

1b 33 30

30 31 32 0d 0a

1b 32

30 31 32 0d 0a

Set horizontal and vertical movement units

Name

Set horizontal and vertical movement units

Code

ASCII ：GSP x y

DEC ：29 80 x y

HEX ：1D 50 x y

Function

Horizontal movement unit =25.4/x mm(1/x inch）

Vertica movement unit =l25.4/y mm(1/y inch）

When set X=0,Y=0, X and Y will display default value.

Range

0 ≤ x ≤ 255,0 ≤ y ≤ 255

Default

x=180,y=360

Notes

None

Example

None

Set line space to default

Name

Set line space to default

Code

ASCII ：ESC 2

DEC：27 50

HEX ：1B 32

Function

Set line space to default 30 dots

Range

None

Default

None

Notes

Line space in details pls check ESC 3 command.

If the line spacesettedis less than the height character in the line,the line

space of this line is equal to the height of the highest character

It can use ESC 3 to define line space.

Example

None

CSN-80V User manual

20

Set character print font

Name

set character print font

Code

ASCII ：ESC M n

DEC ：27 77 n

HEX ：1B 4D n

Function

set character print font

parameter n bit definition as below

n = 0，font 12*24

n = 1，font 9*17

Range

None

Default

n = 0

Notes

The command is effective withcharacter.

The command is disabled when ESC@, printer reset or blackout.

Example

1B 40 1B 4D 00 30 31 32 0D 0A

1B 40 1B 4D 01 30 31 32 0D 0A

Set character printing method

Name

Set character printing method

Code

ASCII ：ESC ! n

DEC ：27 33 n

HEX：1B 21 n

Function

Set character printing methods(font,highlight,inversion,bold,double

hight,double width and underline),parameter n bit definition as below:

Bit Function Value

0 1

0 FontNormal Small character

1 Undefined

2 Undefined

3Bold CancelSetting

4 Double hightCancel Setting

5 Double widthCancel Setting

6 Undefined

7 Underline Cancel Setting

Range

None

Default

n = 0

Notes

The command is effective with Chinese and foreign languages.

The command is disabled when ESC@, printer reset or power off

Example

1B 40 1B 21 01 30 31 32 0D 0A

1B 40 1B 21 02 30 31 32 0D 0A

1B 40 1B 21 04 30 31 32 0D 0A

1B 40 1B 21 08 30 31 32 0D 0A

Page is loading ...

Cashino CSN-80V User manual

Cashino CSN-80V User manual

Other documents