Scag Power Equipment SWZ Hydro Drive User manual

Brand: Scag Power Equipment

Model: SWZ Hydro Drive

Category: Lawnmowers

Type: User manual

MODEL SWZ

OPERATOR’S MANUAL

THIS MANUAL CONTAINS THE OPERATING

INSTRUCTIONS AND SAFETY INFORMA-

TION FOR YOUR SCAG MOWER. READING

THIS MANUAL CAN PROVIDE YOU WITH

ASSISTANCE IN MAINTENANCE AND AD-

JUSTMENT PROCEDURES TO KEEP YOUR

MOWER PERFORMING TO MAXIMUM EFFI-

CIENCY. THE SPECIFIC MODELS THAT THIS

BOOK COVERS ARE CONTAINED ON THE

INSIDE COVER. BEFORE OPERATING YOUR

MACHINE, PLEASE READ ALL THE INFOR-

MATION ENCLOSED.

PART NUMBER 03086

This manual covers the operating instructions

and illustrated parts list for:

SWZ36A-14KA with a serial number of 6230001 to 6239999

SWZ36A-15KA with a serial number of 7190001 to 7199999

SWZ48A-17KA with a serial number of 6260001 to 6269999

SWZ52A-17KA with a serial number of 6280001 to 6289999

SWZ-17KA with a serial number of 6290001 to 6299999

SWZ-21KAE with a serial number of 6300001 to 6309999

SWM-52A with a serial number of 6320001 to 6329999

SWM-72/E with a serial number of 5240001 to 5249999

Always use the entire serial number listed on the serial number

tag when referring to this product.

* Keep all shields in place, especially the grass discharge chute.

* Before performing any maintenance or service, stop the machine and

remove the spark plug wire and ignition key.

* If a mechanism becomes clogged, stop the engine before cleaning.

* Keep hands, feet and clothing away from power-driven parts.

* Read this manual completely as well as other manuals that came

with your mower.

* Keep others off the tractor (only one person at a time)

FAILURE TO FOLLOW SAFE OPERATING PRACTICES

MAY RESULT IN SERIOUS INJURY.

REMEMBER - YOUR MOWER IS ONLY AS SAFE AS THE OPERATOR!

Hazard control and accident prevention are dependent upon the awareness,

concern, prudence, and proper training of the personnel involved in the

operation, transport, maintenance, and storage of the equipment.

WARNING:

TABLE OF CONTENTS

SUBJECT PAGE

Introduction.................................................................................................. 1

General Safety Instructions.......................................................................... 1

Signal Words ............................................................................................... 1

Symbols....................................................................................................... 2-3

Before Operating ......................................................................................... 4

While Operating........................................................................................... 4

Maintenance and Storage ........................................................................... 5

Initial Run-In Procedures ............................................................................. 6

Mower Operation ......................................................................................... 6

Cutter Deck Belt Adjustments...................................................................... 7

Cutter Deck Adjustments ............................................................................. 8

Blade Height Adjustments ........................................................................... 8

Cutter Blades............................................................................................... 9

Neutral Adjustment ...................................................................................... 9

Steering Control Rod Adjustment ................................................................ 10

Tracking Adjustment .................................................................................... 10

Parking Brake .............................................................................................. 10

Lubrication and Maintenance Chart ............................................................ 11

Troubleshooting Cutting Conditions ............................................................ 12-14

Technical Specifications.............................................................................. 15-16

Notes .........................................................................................................................17

WE SUPPORT OPE

TECHNICIAN

CERTIFICATION

Equipment & Engine

Training Council

MEMBER

TABLE OF CONTENTS

(CONTINUED)

SUBJECT PAGE

Illustrated Parts List

SWM-36A"Cutter Deck ..................................................................... 18-19

SWM-48A", 52A", 61A", 72" Cutter Decks.............................................. 20-21

Engine Deck................................................................................................ 22-23

Drive And Brake Components.................................................................. 24-25

Handle Assembly........................................................................................ 26-27

Hydraulic Assembly.......................................................................... 28-29

Hydraulic Pump Assembly................................................................ 30-31

Engine Deck Wire Harness-Kohler (Single Cyl.) & 17KA................... 32

Engine Deck Wire Harness- Kohler Command V-Twin...................... 32

Handle Wire Harness-Electric Start......................................................... 33

Wire Harness W/Relay............................................................................... 33

Engine Deck Wire Harness-14 Kawasaki............................................... 34

Handle Wire Harness-Manual Start......................................................... 34

Handle Wire Harness-Kawasaki Electric Start.................................. 35

Engine Deck Wire Harness-Kawasaki Electric Start......................... 35

Replacement Decals..................................................................................36-38

Warranty Statement...............................................................Inside Back Cover

SIGNAL WORDS

This symbol means Attention! Become Alert!

Your Safety is Involved!" The symbol is used

with the following signal words to attract your

attention to safety messages found on the decals and

throughout this manual. The message that follows

the symbol contains important information about

safety. To avoid injury and possible death, carefully

read the message! Be sure to fully understand the

causes of possible injury or death.

Signal Word:

It is a distinctive word on safety decals and through-

out this manual that alerts the viewer to the existence

and relative degree of the hazard.

The signal word DANGER denotes that an ex-

tremely hazardous situation exists on or near the

machine that could result in high probability of

death or irreparable injury if proper precautions are

not taken.

The signal word WARNING denotes that a hazard

exists on or near the machine that can result in injury

or death if proper precautions are not taken.

The signal word CAUTION is a reminder of

safety practices on or near the machine that could

result in personal injury if proper precautions are

not taken.

INTRODUCTION

Your mower was built to the highest standards in the

industry. However, the prolonged life and maxi-

mum efficiency of your mower depends on you

following the operating, maintenance and adjust-

ment instructions in this manual.

We encourage you to contact your dealer for repairs.

All Scag dealers are informed of the latest methods

to service this equipment and provide prompt and

efficient service in the field or at their service shop.

They carry a full line of Scag service parts.

A replacement Operator's Manual is available from

your Scag Servicing Dealer or by contacting Scag

Power Equipment, Service Department, at P.O. Box

152, Mayville, WI 53050. Please indicate the

complete model and serial number of your Scag

product.

USE OF OTHER THAN ORIGINAL SCAG

REPLACEMENT PARTS WILL VOID THE

WARRANTY.

The Right and Left, Front and Rear of the

machine are referenced from the operators perspec-

tive when in the normal operating position and

facing the forward travel direction.

GENERAL SAFETY INSTRUCTIONS

READ THIS OPERATOR'S MANUAL and

instructions furnished with attachments.

Perform only those maintenance procedures de-

scribed in this manual. If major repairs are ever

needed or assistance is desired, contact an Author-

ized Scag Dealer. To ensure optimum performance

and safety, always purchase genuine SCAG replace-

ment parts and accessories.

Your safety and the safety of others depends signifi-

cantly upon your knowledge and understanding of

all correct operating practices and procedures of this

machine.

WARNING:

CAUTION:

CE Mark

Transmission

Choke

On/Start Spring Tension on Idler

Oil

Off/Stop

SYMBOL DESCRIPTION

ISO Symbols

Spinning Blade

48071S

Parking Brake

WARNING

FALLING HAZARD

USE ONLY SCAG APPROVED

RIDING ATTACHMENTS

SEE OPERATOR'S MANUAL

481109

Falling Hazard

SlowFast

Cutting element - Engage

Cutting element - Basic symbol

Cutting element - Disengage

Continuously variable - Linear

Read operator's manual

Keep bystanders away

Pinch Point

481039S

SYMBOL DESCRIPTION SYMBOL DESCRIPTION

Hourmeter/elapsed operating hours

BEFORE OPERATING

1. Know the controls and how to stop quickly.

2. Do not allow children to operate the machine.

Do not allow adults to operate the machine

without proper instruction.

3. Remove all debris or other objects that might be

picked up and thrown by the cutter blades. Keep

all bystanders away from the mowing area.

4. Keep all shields, safety devices, and decals in

place. If a shield, safety device or decal is

defective or damaged, repair or replace it before

operating. Also, check all nuts, bolts and screws

for proper tightness, to assure the machine is in

safe operating condition.

5. Do not operate the machine while wearing

sandals, tennis shoes, sneakers or shorts. Also,

do not wear loose fitting clothing which could

get caught in moving parts. Always wear long

pants and substantial shoes. Wearing safety

glasses and safety shoes is advisable and required

by some local ordinances and insurance regula-

tions.

6. Fill the fuel tank with clean, fresh gasoline, with

a minimum octane rating of 87. Avoid spilling

gasoline. Gasoline is highly flammable, handle it

carefully.

A. Use an approved gasoline container.

B. Do not fill the tank while the engine is hot or

running.

C. Do not smoke while handling gasoline.

D. Fill the fuel tank outdoors and up to approxi-

mately 1" (25 mm) below the bottom of the

filler neck.

E. Wipe up any spilled gasoline.

7. Before attempting to start the engine, move the

speed adjustment lever into the neutral position,

move the blade engagement switch to the OFF

position, apply the parking brake, and move the

neutral latches to neutral.

WHILE OPERATING

1. Start the engine when the neutral latches are in

the neutral lock position, the cutter blades are

disengaged, the parking brake is on and the

speed adjustment lever is in the neutral position.

2. Do not run the engine in a confined area without

adequate ventilation. Exhaust fumes are hazard-

ous and could possibly be deadly.

3. Using the machine demands attention. To

prevent loss of control:

A. Mow only in daylight or when there is good

artificial light.

B. Watch for holes or other hidden hazards.

C. Do not drive close to a drop-off, ditch, creek

bank, or other hazard.

D. Reduce speed when making sharp turns and

when turning on hillsides.

E. Always be sure of your footing. Keep a firm

hold on the handles and walk---never run.

F. Do not operate where conditions are slippery.

4. The discharge chute must always be installed and

in the down position on the side discharge cutter

deck except when the Scag optional grass

catcher or mulching plate are properly installed.

If the discharge area should plug, shut the engine

off and wait for all movement to stop before

removing the obstruction.

5. Disengage the blades and wait for them to stop

before crossing gravel drives, walks or roads.

6. Shut the engine off and wait until the blades

come to a complete stop before removing the

grass catcher container.

7. Never raise the cutter deck while the blades are

rotating.

8. Always park the mower and/or start the engine

on a level surface. Apply the parking brake to

prevent the mower from moving when you are

not in the operators position.

13. Do not pass or stand on the grass discharge side

of any mower with the engine running. Stop

operation when another person approaches.

9. If the cutting blades should strike a solid object or

the equipment should start to vibrate abnormally,

stop the engine, disconnect the spark plug wire, and

check immediately for the cause. Vibration is

generally a warning of trouble. Check the machine

for damaged or defective parts. Repair any damage

before starting the engine or operating the cutter

deck. Be sure the blades are in good condition and

the blade bolts are tight.

10. Reduce speed and exercise extreme caution on

slopes and in sharp turns to prevent tipping or

loss of control. Be especially cautious when

changing directions on slopes.

DO NOT operate on steep slopes. To check a

slope, attempt to back up it (with the cutter deck

down). If the machine can back up the slope

without the wheels slipping, reduce speed and

use extreme caution. ALWAYS FOLLOW OSHA

APPROVED OPERATION.

11. Do not touch the engine or muffler while the

engine is running or soon after it is stopped.

These areas could be hot enough to cause a burn.

12. Before leaving the operators position or leaving

the mower unattended, move the speed adjust-

ment lever into the neutral position, place the

neutral latches in the neutral lock position, apply

the parking brake, and move the blade engage-

ment switch to OFF. Shut the engine OFF and

remove the key.

14. Use only Scag approved riding attachments.

Scag Approved Riding Attachments:

RS-ZT

Using unapproved attachments, (especially

"stand-up" riding attachments) may be hazardous.

MAINTENANCE AND STORAGE

1. Disconnect the spark plug wire from the spark

plug to prevent accidental starting of the engine

when servicing, adjusting or storing the machine.

2. If the mower must be tipped to perform mainte-

nance or adjustment, remove the battery, drain

the gasoline from the fuel tank and the oil from

the crankcase.

3. To reduce potential fire hazard, keep the engine

free of excessive grease, grass, leaves and accu-

mulations of dirt.

4. Be sure the machine is in safe operating condi-

tion by keeping nuts, bolts, and screws tight.

Check the blade mounting bolts and nuts fre-

quently to be sure they are tightened.

5. If the engine must be running to perform a

maintenance adjustment, keep hands, feet,

clothing and other parts of the body away from

the cutter deck blades and other moving parts.

6. Do not overspeed the engine by changing gover-

nor settings. To be sure of safety and accuracy,

have an authorized dealer check maximum

engine speed with a tachometer.

7. The engine must be shut off before checking the

oil or adding oil to the crankcase.

8. Allow the engine to cool before storing the

mower in any enclosure such as a garage or

storage shed. Make sure the fuel tank is empty if

the machine is to be stored in excess of 30 days.

Do not store the mower near any open flame or

where gasoline fumes may be ignited by a spark.

WARNING:

WARNING

FALLING HAZARD

USE ONLY SCAG APPROVED

RIDING ATTACHMENTS

SEE OPERATOR'S MANUAL 481109

9. Always store gasoline in a safety-approved, red

container.

10. Be careful when servicing the battery as it

contains acid, which is corrosive and could cause

burns to skin and clothing.

11. Batteries release explosive gases when being

charged or discharged. Keep batteries away

from any source of sparks and/or flame.

12. Make sure all hydraulic connections are tight and

all hydraulic hoses and lines are in good condi-

tion before starting the machine.

13. Hydraulic fluid is under high pressure. If you

need service on your hydraulic system, please

see your authorized Scag dealer.

INITIAL RUN-IN PROCEDURES

(FIRST DAY OF USE OR APPROXI-

MATELY 10 HOURS)

1. Check the belts for proper tension at 2, 4 and 8

hours. Adjust as needed.

2. Check the steering control rods and the speed

control for neutral adjustment. (See Adjust

ments, page 6-8)

3. Check the tires for proper pressure.

Caster Wheels 25 psi.

Drive Wheels 15 psi.

4. Check for loose hardware. Tighten as needed.

5. Check the safety switches for proper adjustment:

* The engine should crank and start if the

machine is in neutral, the PTO engage-

ment switch is OFF and the parking brake

is ON.

6. Apply lubricant to all the grease fittings. Lubri-

cant was applied at the factory. This is just a

precautionary check to make sure that all the

fittings have been lubricated.

MOWER OPERATION

-NOTE-

Use gasoline with an octane rating no less than

87.

* The speed adjustment lever must be in

NEUTRAL.

* The blade clutch switch must be in the OFF

position.

* The neutral latches must be in the neutral

lock position.

* The key switch must be on.

* The parking brake must be on.

3. Start the engine:

* Choke as required. If the engine is cold, pull

the choke knob out. When the engine starts,

slowly push the choke in. If the engine

stalls, repeat the above operation. When the

engine is warm, choking may not be necessary.

* Cold starting. In the spring and fall when the

morning temperatures are cool it may be difficult

to start the machine due to the parastatic load

from the hydraulic drive. To relieve this load,

pull out and up on the de-clutch chain located

on the right side of the machine behind the tire.

This will allow you to start the engine easilly.

When the engine is warmed up, slowly release

the de-clutch chain to engage the hydraulic

system.

4. Engage the cutter blades by pulling the blade clutch

switch into the ON position. Push the switch to the

OFF position to disengage the cutter blades.

1. Read and understand the safety instructions

before attempting to operate this machine.

2. Before starting the engine:

* Check the oil level in the engine and the

hydraulic reservoir.

* Fill the fuel tank with clean, fresh, lead-

free gasoline.

* Open the fuel valve on the bottom of the

fuel tank.

-NOTE-

When PTO is engaged or (possibly) disengaged,

a squealing sound from the underside of the

machine is normal. It is caused by the electric

clutch plates meshing as the mower comes up to

speed. For best equipment life, engage the

clutch with the engine at 1/2 throttle, not under

full load.

If you are not familiar with the operation of the

hydrostatic drive and zero turn feature, practice

turning and maneuvering with the hand controls

before engaging the blades.

5. Release the parking brake. Move the speed

adjustment lever to the desired mowing speed.

-NOTE-

Top speed is suggested only for transport!

6. While squeezing the steering brake levers with both

hands, release both neutral latches.

7. When the steering brake levers are released, the

machine will travel straight. To make a right turn,

squeeze the RH lever. To turn left, squeeze the LH

lever.

8. TO STOP, squeeze both levers, lock the neutral

latches, and move the speed adjustment lever to

neutral.

9. To move the machine in reverse, squeeze up on

both steering control levers.

ire pressure can be adjusted for

WARNING:

Dump Valve Levers

(normal position)

SGB112

Figure 1. Dump Valves

CUTTER DECK BELT ADJUSTMENTS

-NOTE-

The hydro drive belt is spring loaded and does

not require adjustment.

1. Remove the belt cover.

2. Adjust the cutter deck drive belt using a belt

tension gauge. Adjust the belt so that the belt

moves 1/2" with 10 pounds of pressure. Adjust

the tension by tightening or loosening the J-bolt

nut. (See figure 2)

SC400G

BELT

WASHER

"J" BOLT

NUT

CUTTER DECK DRIVE BELT TENSION

ALIGNMENT IDLER - L.H.

END OF L-SHAPED

BRACKET

Figure 2. Deck Drive Belt Adjustment

390S0138

PULL UP TO ENGAGE

PUSH DOWN TO DISENGAGE

10. To "freewheel" or move the machine around

without the engine running, turn the dump valve

levers located at the back of the pumps to the

"freewheel" positions (see Figure 1). To operate

the machine, the dump valve levers must be

returned to the closed positions.

-NOTE-

Due to initial belt stretch and to prevent the belt

from slipping, check this adjustment after the

first 2 hours, 4 hours and 8 hours of operation.

3.Adjust the RH blade drive belt using a belt

tension gauge. Adjust the belt so that the belt

moves 1/2" with 10 pounds of pressure. Adjust

the tension by tightening or loosening the J-bolt nut.

(See figure 3)

4. Replace the belt cover.

"J" Bolt

Nut

Belt

Deck

Washer

Figure 3. Cutter Deck Belt Adjustment R.H.

SC405G

LOW CUT (1 3/4"- 3")

HIGH CUT (3 1/4"- 4 1/2")

MID RANGE

(2 1/2"- 3 3/4")

CUTTER DECK HEIGHT ADJUSTMENT

Figure 4. Cutting Height Adjustment

Caster spacers also can be repositioned to change

cutting heights and to change the pitch of the deck.

(See figure 5)

Figure 5. Caster Wheel Spacers

BLADE HEIGHT ADJUSTMENT

Adjusting the blade height can be done by moving

any number of the five smaller 1/4" spacers on the

blade mounting bolts to the top of the spindle shaft

or below the spindle shaft.

-NOTE-

All blades should be positioned equally.

For best cut and discharge, a minimum of three

spacers should be installed between the blade and the

spindle (See figure 6).

SC406G99

PIN SPACERS

REPOSITIONING SPACERS

CUTTER DECK ADJUSTMENTS

Due to the many cutting conditions that exist, it is

difficult to suggest a cutter deck setting that will

work for every lawn. There are two adjustments that

can be made on these decks, pitch and height.

PITCH is the angle of the blades (comparing front to

rear). A 1/4" downward pitch (front of deck down)

is recommended for best cutting performance.

HEIGHT is the nominal distance the blade is off of

the ground. This measurement is made with the

blades pointed side to side and distance is measured

between cutting tip and ground. (Also see Blade

Height Adjustment)

Changes to the cutting height can be achieved by

repositioning the cutter deck. (This adjustment will

also effect the pitch of the deck). There are three

available positions (see figure 4).

CUTTER BLADES

Do not sharpen beyond 1/3 of the width of the blade.

(See figure 7)

-NOTE-

Dress the blade with a file. Using a wheel

grinder may burn the blade. Check the balance

of the blade. If blades are out of balance, vibra-

tion and premature wear of spindle assembly can

occur. See your authorized Scag dealer for

blade balancing or special tools, if you choose to

balance your own blades.

SC407G

Figure 6. Blade Spacers

SC4O8G

ANGLE BLADE BACK

DO NOT CUT IN

X MUST NOT EXCEED

1/3 BLADE WIDTH

Figure 7. Blade Sharpening

NEUTRAL ADJUSTMENT

-NOTE-

Neutral has been set by your Scag dealer at the

time of setup and normally does not need to be

adjusted. If, however, you find that the neutral

has come out of adjustment follow the proce-

dure below.

1. Raise the drive wheels off the ground and block the

caster wheels.

2. Make sure the speed control lever is in neutral, the

steering control levers are in the neutral latch

position, and the parking brake is on. Start the

engine.

3. Release the parking brake and note if the tires are

rotating.

4. Starting on the left side of the machine, rotate the

tracking adjustment knob counter clockwise just

until the LH wheel starts to creep forward. Make a

note of the position of the adjusting knob. (See

figure 8)

5. Turn the adjusting knob clockwise just until the

wheel turns rearward. Make a note of the position

of the adjusting knob. To adjust neutral, split the

difference between the two noted positions of the

adjusting knob.

6. Turn the engine off.

Figure 8. Neutral Adjustment

481878

SLOW

FAST

TRACKING

ADJUSTMENT

SEE OPERATOR'S

MANUAL

2. Squeeze the steering control levers and release the

neutral latch. Slowly release the steering control

levers, allowing the machine to move forward.

3. If the machine pulls to one side, turn the tracking

adjustment knob on the slower side counter clock-

wise until the machine tracks straight

(see Figure 6).

4. Bring the steering control levers back to the neutral

lock position and check to see that the machine

does not creep forward on the adjusted wheel.

5. If the machine creeps in neutral you have moved out

of the neutral band and will have to turn the tracking

adjustment knob clockwise until the machine does

not creep.

6. Repeat steps 1 and 2. If the machine pulls to one

side, turn the tracking adjustment knob on the faster

side clockwise until the machine tracks straight.

8. If tracking cannot be achieved, contact your Scag

servicing dealer.

PARKING BRAKE

1. Adjust the parking brake so that when the brake

hand lever is against the stop on the handle bar, the

brake levers on the brake shaft weldment are

against the stops on the engine deck.

Adjust the brake only enough to hold the

machine. Excessive force may cause damage

to the machine or brake components.

2. Adjust the brake actuator rod on either side of the

machine to obtain proper brake adjustment.

STEERING CONTROL ROD

ADJUSTMENT -NOTE-

This adjustment is made to allow the steering

control levers to be moved out of the neutral

latch without engaging reverse.

Before making this adjustment be sure that the

speed control bearing is just touching the speed

control cam and that the bellcrank bearing is

resting in the center groove of the neutral cam.

1. Remove the speed control spring. Remove the

steering control rod swivel hair pin. Check the

location of the swivel in the slotted hole in the bell

crank .

2. Turn the swivel joint on the steering control rods

until the swivel joint is centered in the slot in the

bellcrank.

3. Reinstall the speed control spring onto the swivel.

Install the hair pin onto the swivel.

TRACKING ADJUSTMENT

-NOTE-

Before proceeding with this adjustment, be sure

that the tire pressures are correct. (see page 4)

and that the neutral adjustment and the steering

control rod adjustment have been completed.

1. With the machine on a flat level surface, start the

engine and place the speed adjustment lever into the

speed that will most often be used.

CAUTION:

Figure 5. Control Rod Adjustment

481878

SLOW

FAST

TRACKING

ADJUSTMENT

SEE OPERATOR'S

MANUAL

Figure 6. Tracking Adjustment

481878

SLOW

FAST

TRACKING

ADJUSTMENT

SEE OPERATOR'S

MANUAL

390s0198

Center of

Slot

COMMENTS

PROCEDURE

LUBRICATION & MAINTENANCE

+ Grease spindle until grease comes out the relief valve

Compatible Greases: Lidok EP #2 (found at industrial shops)

Ronex MP (Exxon service stations)

Shell Alvania (Shell service stations)

Mobilux #2 (Mobil service stations)

Super Lub M EP #2 (Conoco service stations)

XCheck all hardware for proper tightness

Change engine oil and filter at 5 hours

X Check engine oil Do not over fill

X Remove debris from under belt cover More often if needed

X Sharpen cutter blades More often if needed

X Grease spindle bearings + US Lithium MP White Grease 2125

X Clean air filter More often if needed

X Check belt tension Adjust as needed

X Check tire pressure Add or adjust as required

X Check battery level Adjust as needed

X Replace air filter More often if needed

X Grease caster wheel bearings Chassis grease

X Grease caster wheel pivot shafts Chassis grease

X Grease idler pulley bracket on cutter deck Chassis grease

X Change hydrostatic oil filter Clean area before removing the filter

X Change engine oil and filter See engine manufacturer information

X Grease idler arm pivots Chassis grease

X Grease brake hand lever Chassis grease

X Grease brake actuator levers Chassis grease

X Check all hardware for proper tightness

X Adjust air gap on electric clutch Contact your Scag dealer for information about

X Drain hydraulic system and replace oil making this adjustment.

BREAK-IN

8 HOURS (DAILY)

40 HOURS (WEEKLY)

100 HOURS (BIWEEKLY)

500 HRS OR ANNUALLY

Stringers - Occasional Low engine RPM Run engine at full 3600 RPM

Blades of Uncut

Grass Ground speed too fast Slow speed to adjust for conditions

Wet grass Cut grass after it has dried out

Dull blades, incorrect sharpening Sharpen blades

Deck plugged, grass accumulation Clean underside of deck

Belt slipping Adjust belt tension

Streaking - Strips of Dull, worn blades Sharpen blades

Uncut Grass in Cutting

Path Incorrect blade sharpening Sharpen blades

Low engine RPM Run engine at full 3600 RPM

Belt slipping Adjust belt tension

Deck plugged, grass accumulation Clean underside of deck

Ground speed too fast Slow speed to adjust for conditions

Wet grass Cut grass after it has dried out

Bent blades Replace blades

Width of Deck

SGB018

CONDITION CAUSE CURE

Width of Deck

SGB020

Width

Deck

Width

Deck

SGB019

Streaking - Strips of Not enough overlapping Increase the overlap of each

Uncut Grass Between between rows pass

Cutting Paths

TROUBLESHOOTING CUTTING CONDITIONS

CONDITION

TROUBLESHOOTING

CAUSE CURE

Sloping Ridge Across Tire pressures not equal Check and adjust tire pressure

Width of Cutting Path Wheels uneven Check and adjust tire pressure

Deck mounted incorrectly See your authorized SCAG dealer

Uneven Cut on Flat Lift worn off of blade Replace blade

Ground - Wavy

High-Low Blade upside down Mount with cutting edge toward

Appearance, ground

Scalloped Cut, or

Rough Contour Deck plugged,grass accumulation Clean underside of deck

Too much blade angle (deck pitch) Adjust pitch and level

Deck mounted improperly See your authorized SCAG dealer

Bent spindle area See your authorized SCAG dealer

Dull blade Sharpen blade

Uneven Cut on Uneven ground May need to reduce ground speed,

Uneven Ground - raise cutting height, and/or change

Wavy Appearance, direction of cut

High-Low Scalloped

Cut, or Rough Contour

Width of Deck

SGB020

Width of Deck

SGB021

Width of Deck

SGB023

Scalping - Blades Low tire pressures Check and adjust pressures

Hitting Dirt or

Cutting Very Close to Ground speed too fast Slow speed to adjust for conditions

the Ground Cutting too low May need to reduce ground speed,

raise cutting height, change direction

of cut, and/or change pitch and level

Rough terrain May need to reduce ground speed,

raise cutting height, and/or change

direction of cut

Ground speed too fast Slow speed to adjust for conditions

Wet grass Cut grass after it has dried out

Step Cut Blades not mounted evenly Adjust pitch and level

Ridge in Center of

Cutting Path Bent blade Replace blade

Internal spindle failure See your authorized SCAG dealer

Mounting of spindle incorrect See your authorized SCAG dealer

Slope Cut - Sloping Bent spindle mounting area See your authorized SCAG dealer

Ridges Across Width

of Cutting Path Internal spindle failure See your authorized SCAG dealer

Bent deck housing See your authorized SCAG dealer

TROUBLESHOOTING

CONDITION CAUSE CURE

Width of Deck

SGB024

Width of Deck

SGB025

Width of Deck

SGB022

TECHNICAL SPECIFICATIONS

ENGINES

General Type: Heavy duty industrial/commercial

Brand: Kohler, Kawasaki,

Models: Kohler CV15T, Kaw. FC420V (14HP),FH451V (15HP),

FH500V (17HP)

Horsepower: Kohler 15HP; Kaw. 14HP; Kaw. 15HP; Kaw. 17HP

Type: 4 cycle gas, vertical shaft engines

Displacement: Kohler: 15HP = 426cc

Kawasaki: 14HP = 423cc, 17HP = 494cc

Cylinders: Varied - see manufacturer's specifications

Governor: Mechanical type governor with variable speed control set

at 3600 rpm (+75 rpm), idle set at 1200 rpm (+75 rpm)

Exhaust Group: Single exhaust canister muffler

Fuel Pump Group: Varied - See manufacturer's specifications

Oil Pump Group: Varied - See manufacturer's specifications

Valve Group: Varied - See manufacturer's specifications

Starter/Electrical: Electronic Ignition with recoil starter or 12 volt battery with

alternator, solid state ignition with key start

Charging System: 15 amp

ENGINE DECK

Thickness: 7 gauge steel

Fuel Tank: 5 gallon (19.0 litres) seamless polyethylene

Drive Wheels/Tires: 16x6.50-8 four-ply pneumatic tubeless, radius edge

Brakes: Dynamic braking through hydro drive system

Axles: 1" tapered

Handle Bars: 1-1/4" diameter

DRIVE SYSTEM

Type: Hydro drive with two variable displacement pumps and two

cast-iron high torque motors

Hydro Pumps: Two Hydro-Gear Model BDP 10L pumps with dump valves for

movement without running the engine

Drive Wheel Motors: Two 12 cu. inch cast-iron high torque motors

Hydro Fluid Cooling Group: 4qt. capacity cooling radiator, uses, SAE 20W50 fluid and

10 micron filter

Steering / Travel Control:: Independent handle controls for each wheel, squeeze to move

from forward to neutral to reverse, neutral lock lever, speed

range controlled with single lever (patented design), in-field

tracking adjustment with no tools necessary

Parking Brakes: 7.5" drum, band brake, one on each wheel

Dump Valves: Allows for movement without engine running

Axles: 1" tapered motor shafts

Wire Harness: 14 gauge wire

Safety Group: Handle actuated operator presence system (patented design),

blade / clutch and transmission interlock to engine kill

Forward Speed Range: 0 to 7.4 mph

Reverse Speed Range: 0 to 3.0 mph

Date of Issue: February , 2001

Specifications Subject to Change Without Notice

TECHNICAL SPECIFICATIONS (CON'T)

CUTTER DECKS SWM 36 Advantage, SWM 48 Advantage, SWM 52 Advantage,

SWM 72

Type: Out-front design with anti-scalp rollers

Construction: SWM36A, 48A: 7-gauge steel with 7-gauge (3/16") steel skirt

SWM52A, 61A:10-gauge steel with 7-gauge (3/16") steel skirt

Cutting Width: 35.5" (90.2 cm), 48.0 (122.0 cm), 52.0 " (132.0 cm),

61.0 " (155.0 cm), 71.5" (181.6 cm)

Cutting Height Adjustment: Adjustable from 1-3/4" to 4-1/4" in 1/4" increments

Cutter Blades: Marbain®, .197 thickness

SWM 36: Two (2) 18"; SWM 48: Three (3) 16.5"

SWM 52: Three (3) 18"; SWM 61: Three (3) 21"

SM72: Three (3) 24" blades

Blade Engagement: Electric blade brake clutch with instrument panel switch

Discharge Opening: Extra wide 11.5", 13.75 " discharge opening with hinged

chute

Caster Wheels: 9.4 x 3.5 smooth tread flotation, inner tubes, split rims, roller

bearings, with quick pin removal

Spindles: Cast housing, taper roller bearing, low maintenance with

top access grease fitting and grease overfill relief poppet

Spindle Pulleys: Cast-iron with easily removed taper hubs

Idler Pulley: 5" diameter pulley, welded and riveted construction,

1-3/8" O.D. Bearing

Idler Arm: Heavy duty idler arm of 1/4" channel steel

Cutter Deck Belts: B-section with Kevlar cord

ADDITIONAL SPECIFICATIONS

OPTIONAL ITEMS/ATTACHMENTS

Fabric Grass Catcher: GC-F4 Grass Catcher with 4 cubic ft. capacity

Metal Grass Catcher: GC-4D Grass Catcher with 4 cubic ft. capacity and rope pull

dump or pick-up and dump

Steerable Sulky: RS-ZT Steerable Sulky with padded seat and full articulation

for zero-radius turning

Mulch Master: Steel plate fits over discharge opening and steel baffles between each

balde with Eliminator Blades. Installs and removes in the field.

APPROXIMATE DIMENSIONS SWM36A SWM48A SWM52A SWM61A

Length: 74.0" 76" 78" 76.0"

Length with Grass Catcher: 74.0" 76" 78" 76.0"

Tracking Width: 37.0" 42.0" 42.0" 42.0"

Width: 54.5" 59.0" 62" 70.0"

Width (with discharge chute up): 37.5" 49.0" 52" 63.0"

With with grass catcher: 55.0" 65.0" 78" 80.0"

Height: 43" 43" 43" 43"

Height with grass catcher: 43" 43" 43" 43"

Weight 515 lbs. 560 lbs. 610 lbs. 625 lbs.

Weight with grass catcher: 555 lbs. 600 lbs. 650 lbs. 665lbs.

Turning Radius: Zero Zero Zero Zero

Date of Issue: February ,2001

Specifications Subject To Change Without Notice

Page is loading ...

Scag Power Equipment SWZ Hydro Drive User manual

Brand: Scag Power Equipment

Model: SWZ Hydro Drive

Category: Lawnmowers

Type: User manual

Download PDF

report

Scag Power Equipment SWZ Hydro Drive User manual

Scag Power Equipment SWZ Hydro Drive User manual

Related papers

Other documents