KRAUS KPF-4102CH Installation guide

Brand: KRAUS

Model: KPF-4102CH

Category: Faucets

Type: Installation guide

This manual is also suitable for

INSTALLATION MANUAL

Allyn™ Industrial Pull Down

Single Handle Kitchen Faucet

KPF-4102

Congratulations on the purchase of your new

Kraus plumbing fixture!

Please keep the box and packaging materials until your product is

completely installed. If you have any questions, require technical

assistance or have any problems with your product:

Please contact our Customer Service Team

1-800-775-0703 / [email protected]

Have the model number available and retain a copy of your

receipt with purchase date for reference.

If for any reason this product does not meet your expectations,

please be sure to repack this product in the original box and

packaging material to avoid damage during transit.

DO NOT RETURN TO STORE

STOP

Prior to Installation:

·Make sure you have all necessary parts by checking the diagram and

parts list. If any part is missing or damaged, please contact Kraus

Customer Service at 800-775-0703 for a replacement.

·Read all instructions and safety warnings and ensure you have all tools,

parts, and equipment necessary for a safe installation.

·Turn off the hot and cold water supply at the angle stops and turn on

the old faucet to release any built up pressure. Remove existing faucet.

Pre-drilled hole size requirement: 1 3/8" (min)

Max countertop thickness: 3 1/2”

Care & Maintenance

* To keep the product clean & shining, follow the steps below:

1. Rinse with clean water & dry with a soft cloth

2. Do not clean with soaps, acid, polish, abrasives or harsh cleaners

3. Do not use cloth with a coarse surface

4. Unscrew the aerator and clean when necessary

* This installation manual is subject to change without further notice.

ACID

STOP

For technical assistance or replacement parts, please contact Kraus Customer

Service and one of our representatives will be happy to help:

Toll-Free: 800-775-0703 or [email protected]

Tools Required

Wrench Phillips Screwdriver Silicone Sealant Safety Goggles Pipe Tape

Diagram and Parts List

A. Spray Head

B. Faucet Body

C. Rubber Washer

D. Metal Washer

E. Mounting Nut

F. Screws

G. Weight

H. Weight Clip

I. Quick Connector

J. Hex Wrench

Faucet Dimensions

3/8”-compression

3.2

5''

[128.1mm]

16 3/4''

[425.7mm]

Max: 3 1/2''

[89.6mm]

11 1/8''

[283.7mm]

8 7/8''

[226.4mm]

8 1/2''

[217.4mm]

Ø2 1/4''

[58.0mm]

Installer Tip:

Shut off main water supply before installing new faucet.

(2 N.m

Max)

Step 1: Installing the faucet

Step 2: Securing the faucet assembly

Push the quick connector (I) firmly

upward and attach it to the receiving

block (a). Pull down moderately to

ensure the connection has been made.

Shut off the water supply. Place the

faucet (B) through the hole in the

countertop. Secure the faucet (B) to

the countertop using the rubber

washer (C), metal washer (D) and

mounting nut (E) provided. Hand

tighten the nut (E) onto the faucet

assembly. Lock the nut (E) into position

by tightening the screws (F) with a

phillips screwdriver. Do not

overtighten.

Weight

here

Weight

here

Step 3: Installing the counterweight

Step 4: Connect waterlines to main valve

Attach waterlines to angle stops and

tighten until snug. Turn on angle stops

and check for leaks (DO NOT TURN

FAUCET ON).

Install the weight clip (H) at the point of

the hose marking "weight here". Insert

the weight (G) onto the weight clip (H) by

sliding it down onto the weight clip (H).

Step 5: Flush faucet

Pull the hose assembly out of the spout

and remove the spray head (A) by

unscrewing it from the hose in a

counterclockwise direction. Be sure to

hold the end of the hose down into the

sink and turn the faucet on to the warm

position where it mixes hot and cold

water. Flush the water lines for one

minute. This flushes away any debris that

could cause damage to internal parts.

Check for leaks. Retighten any

connections if necessary, but do not

overtighten. Reinstall the spray head (A)

by hand tightening it back onto the spray

hose. After installation is completed, turn

on the hot and cold water supplies. Check

for leaks.

NOTE: Please make sure filter washers

are installed before connecting to the

main valve.

NOTE: Please make sure the washer

(1) is installed before attaching the

spray head to the hose.

Replacement Parts

1. Spray Head

2. Sprayer Washer

3. Sprayer Hose

5. O-Ring

6. Inverter

7. Cartridge

9. Bonnet Nut

10. Cap & O-ring

11. Handle

KP27210

KP27211

KP27257

KP27299

KP27300

KP27301

KP27298

KP27208

KP27209

8. Screw

4. Quick Connector Assembly KP27090

12. Set Screw

KP27307

KP27001

SFACB, CH, MB

SFSB, SFS**

13. Cover Button

14. Hex Wrench

KP27194

15. Rubber & Metal Washer

KP27020

KP27028

16. Mounting Nut & Screw

17. Inverter

KP27079

18. 1.8GPM Flow Restrictor

KP27123

KP27074

19. Weight & Clip Assembly

20. Block

21. O-Ring

KP27212

KP27092

22. Filter Washer

BL, GR**

GRCH, GRSFS,

BLMB, BLSFSB,

BLSFACB*

SFACB, CH, MB

SFSB, SFS**

SFACB, SFSMB,

SFSB, SFS, CH

SFSCH, MB**

KP27073

KP27167

Replacement Parts List Part #Finish / Color

*Denotes spray hose assembly color options:

Spray hose assembly color options:

Black hose with Matte Black connector (BLMB);

Gray hose with Spot-Free Stainless connector

(GRSFS); Grey hose with Chrome connector

(GRCH); Black hose with Spot-Free Black

Stainless connector (BLSFSB); Black hose with

Spot-Free Antique Champagne Bronze

connector (BLSFACB)

**Denotes faucet component color options:

SFSB - Spot Free Black Stainless

SFS - Spot Free Stainless

CH - Chrome

MB - Matte Black

SFSMB - Spot Free Stainless/Matte Black

SFSCH - Spot Free Stainless/Chrome

SFACB - Spot Free Antique Champagne Bronze

GR - Grey

BL - Black

Troubleshooting

If you have followed the instructions carefully and your faucet still does not work properly,

take the following corrective steps:

Leakage under the handle.

PROBLEM CAUSE ACTION

Bonnet nut (9) has

come loose.

Remove the cover button (13). Loosen

set screw (12) with hex wrench (14).

Remove the handle (11). Unscrew cap

(10) (by hand only). Tighten bonnet nut

(9) with an adjustable wrench.

The aerator has an irregular

or reduced water flow.

The aerator is dirty or

misfitted.

Remove the aerator and check for

debris. Ensure that the rubber washer is

properly installed.

Water will not shut off

completely.

Cartridge may need to be

adjusted or replaced.

Remove the cover button (13). Loosen set

screw (12) with hex wrench (14). Remove

the handle (11). Unscrew cap (10) (by

hand only). Loosen the bonnet nut (9) with

an adjustable wrench. Remove the

cartridge (8). Check for cracks.

There is a low flow of water. The filter washers in the

hose connectors are dirty.

Turn off the water supply at the water

valves and unscrew the hose connectors

from the water supply lines. Clean the

washers in the water lines with hot water,

removing any debris or calcium build up.

Faucet - Lifetime Limited Warranty

Kraus USA Plumbing, LLC (“Kraus”) extends this warranty to the original purchaser for personal household use of the

Faucet when purchased from an authorized Kraus dealer and in the location of original installation. This warranty is

non-transferable.

Kraus warrants the structure and finish of the Faucet to be free from defects in material and workmanship under normal

usage for as long as the original purchaser resides in the residence in which the Faucet was first installed.

Kraus warrants the Faucet's sprayhead assembly (including the engine, aerators, structure, restrictors, back flow

preventers, sprayer hoses, braided supply line hoses which encompasses nylon, silicon and stainless steel) of the product

to be free from defects in material and workmanship under normal usage for a period of one (1) year from the date of

purchase.

Kraus warrants the Faucet's cartridge to be free from defects in material and workmanship under normal usage for a

period of five (5) years from the date of purchase.

Any product reported to the authorized dealer or to Kraus as being defective within the warranty period will be repaired

or replaced with a product of equal value at the option of Kraus.

Commercial Warranty

Kraus USA Plumbing, LLC (“Kraus”) warrants its Products for a period of one (1) year to commercial purchasers of

Products used in industrial, commercial and business applications.

Care and Cleaning Instructions

Certain cleaning products may cause damage to a Product's finish and use of the following on the Product will void this

warranty:

Abrasive cleaners such as powders, bleach, ammonia, alcohol or chorine

Abrasive pads, steel wool or wire brushes

What is Not Covered

This warranty does not cover Products that were discontinued when purchased or display Products, whether such

Products were purchased at discount outlets, unauthorized dealers, and/or sold on clearance. This warranty does not

cover any free gifts included with purchase.

This warranty does not cover damage resulting from neglect, misuse (including use for an unintended application),

abuse, carelessness, accident, hard water or mineral deposits, exposure to corrosive materials, improper maintenance,

alteration of the Product, or failure to follow care, cleaning or installation instructions enclosed with your Product. Kraus

recommends that all Kraus Products be installed by a fully licensed and insured trade professional with experience in the

installation of bathroom and/or kitchen manufactured goods.

Codes/Standards Applicable:

•

UPC

NSF/ANSI 372

ASME A112.18.1

1.8GPM 6.8L/min maximum

IAP

LEAD FREE

NSF/ANSI 61

MOR&T

UPC

NSF/ANSI/CAN 61: Q ≤ 1

Download the Kraus Care & Maintenance Guide at:

http://www.kraususa.com/maintenance

How to Make a Warranty Claim

If you are a consumer purchaser, please contact a Kraus Customer Service Representative at:

Kraus USA Plumbing, LLC

12 Harbor Park Drive

Port Washington, NY 11050

Toll-free 800-775-0703

[email protected]

If you are a plumbing contractor or trade professional, please contact a Kraus Pro Representative at:

Kraus USA Plumbing, LLC

12 Harbor Park Drive

Port Washington, NY 11050

516-801-8955

[email protected]

If you are an authorized partner, please contact a Partner Support Representative at:

Kraus USA Plumbing, LLC

12 Harbor Park Drive

Port Washington, NY 11050

516-801-8954

[email protected]

In requesting warranty service, please be ready to provide your proof of purchase and a description of the problem. Shipping charges

will be covered for the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping charges may apply).

International shipping fees are not included.

Limitation on Duration of Implied Warranties

Please note that some states/provinces (including Quebec) do not allow limitations on how long an implied warranty lasts, so the

below limitations may not apply to you. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, ANY IMPLIED WARRANTY,

INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED TO

THE STATUTORY PERIOD OR THE DURATION OF THIS WARRANTY, WHICHEVER IS SHORTER.

Limitation of Special, Incidental or Consequential Damages

Please note that some states/provinces (including Quebec) do not allow the exclusion or limitation of special, incidental or

consequential damages, so the below limitations and exclusions may not apply to you. TO THE MAXIMUM EXTENT PERMITTED BY

APPLICABLE LAW, THIS WARRANTY DOES NOT COVER, AND KRAUS USA PLUMBING, LLC SHALL NOT BE LIABLE FOR, ANY SPECIAL,

INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING LABOR CHARGES TO REPAIR, REPLACE, INSTALL OR REMOVE THIS

PRODUCT), WHETHER ARISING OUT OF BREACH OF ANY EXPRESS OR IMPLIED WARRANTY, BREACH OF CONTRACT, TORT, OR

OTHERWISE.

This warranty gives you specific legal rights, and you may also have other rights which vary from state/province to state/province.

Activate Your Warranty

Access Premium Customer Support

Get Product Information

http://www.kraususa.com/registration

www.kraususa.com

IMPORTANT

KRAUS KPF-4102CH Installation guide

Brand: KRAUS

Model: KPF-4102CH

Category: Faucets

Type: Installation guide

This manual is also suitable for

Download PDF

report

KRAUS KPF-4102CH Installation guide

This manual is also suitable for

KRAUS KPF-4102CH Installation guide

Related papers

Other documents