Poulan Pro 952711962 User manual

Brand: Poulan Pro

Model: 952711962

Category: Grass trimmers

Type: User manual

ENGLISH ESPAÑOL FRANÇAIS

DANGER:

Read and follow all Safety Rules and Operating Instructions before

using this product. Failure to do so can result in serious injury.

PELIGRO:

Lea el manual de instrucciones y siga todas las advertencias e

instrucciones de seguridad. El no hacerlo puede resultar en le-

siones graves.

DANGER:

Lire le manuel d’instructions et bien respecter tous les avertisse-

ments et toutes les instructions de sécurité. Tout défaut de le

faire pourrait entraîner des blessures graves.

For Occasional Use Only

545177328 Rev. 2 3/5/09 BRW

Poulan PRO

1030 Stevens Creek Road

Augusta, GA 30907

Poulan PRO

850 Matheson Blvd. West

Mississauga, Ontario L5V 0B4

Instruction Manual

Manual de Instrucciones

Manuel d’Instructions

PP125

Please do not return unit to retailer.

Por favor, no devuelva el aparato al lugar de compra.

Veuillez ne pas retourner l’outil au détaillant.

1-800-554-6723

www.poulan--pro.com

IDENTIFICATION OF SAFETY SYMBOLS

WARNING: This unit can be dangerous! Careless or improper

use can cause serious injury.

Read the operator’s manual before use. Failure to follow instructions

could result in serious injury. Save operator’s manual.

DANGER: Use only specified trimmer

head, spool, and 0.095 inch (2.4 mm) recom-

mended trimmer line. Never use blades, flailing

devices, wire, rope, string, etc. This attachment is

designed for line trimmer use only. Failure to follow

these instructions may result in serious injury.

Trimmer line can throw objects violently.

You can be blinded or injured. Always

wear hearing protection and safety

glasses marked Z87. Always wear head

protection, heavy, long pants, long

sleeves, boots and gloves.

Hazard zone for thrown objects.

STrimmer line throws objects violently.

SYou and others can be blinded/injured.

SKeep children, bystanders, and animals 50 feet

(15 meters) away.

Secure hair above shoulder length. Do

not wear jewelry, loose clothing, or

clothing with loosing hanging straps,

ties, tassels, etc. They can be caught in

moving parts.

Assist handle to be positioned only below

the arrow.

IDENTIFICATION OF SAFETY SYMBOLS

When servicing unit, use only identical replacement

parts.

Never allow children to operate this unit.

Store unit indoors in a high, dry place out of the reach of

children.

Always stop unit and disconnect spark plug before clean-

ing or servicing.

WARNING: Fire hazard. Never mix, pour, or store gasoline or

use the unit near a flame or sparks (including smoking, open flames, or

work that can cause sparks).

Use unleaded gasoline and two--stroke oil mixed at a ratio of

40:1 (2.5%).

OPTIONAL ATTACHMENTS

These attachments used in combination with the specified powerhead have been evaluated to

ANSI B175.3--2003, “Grass Trimmers and Brushcutters -- Safety Requirements”.

Powerhead including trimmer attachment PP125................................

Brushcutter attachment PP4000C...............................................

These attachments used in combination with the specified powerhead have been evaluated to appli-

cable ISO and EN safety requirement standards by the Swedish Machinery Testing Institute:

Edger attachment PP1000E....................................................

Cultivator attachment PP2000T.................................................

Blower attachment PP3000B...................................................

Pruner attachment PP5000P...................................................

SAFETY RULES

WARNING: When using gardening

appliances, basic safety precautions must al-

ways be followed to reduce the risk of fire and

serious injury. Read and follow all instruc-

tions.

This power unit can be dangerous! Operator

is responsible for following instructions and

warnings on unit and in manual. Read entire

instruction manual before using unit! Be thor-

oughly familiar with the controls and the prop-

er use of the unit. Restrict the use of this unit

to persons who have read, understand, and

will follow the instructions and warnings on

the unit and in the manual. Never allow chil-

dren to operate this unit.

SAFETY INFORMATION

ON THE UNIT

INSTRUCTION

MANUAL

DANGER: Never use blades with line

trimmer attachment. Never use flailing devices

with any attachment. This unit (when used with

supplied line trimmer attachment) is designed

for line trimmer use only. Use of any other ac-

cessories or attachments with line trimmer at-

tachment will increase the risk of injury.

If situations occur which are not covered in

this manual, use care and good judgment. If

you need assistance, contact your authorized

service dealer or call 1-800-554--6723.

OPERATOR SAFETY

SDress properly. Always wear safety glasses

or similar eye protection when operating, or

performing maintenance, on your unit (safety

glasses are available). Eye protection should

be marked Z87.

SAlways wear face or dust mask if operation is

dusty.

SAlways wear heavy, long pants, long sleeves,

boots, and gloves. Wearing safety leg guards

is recommended.

SAlways wear foot protection. Do not go

barefoot or wear sandals. Stay clear of

spinning line.

SSecure hair above shoulder length. Secure or

remove loose clothing or clothing with loosely

hanging ties, straps, tassels, etc. They can be

caught in moving parts.

SBeing fully covered also helps protect you

from debris and pieces of toxic plants thrown

by spinning line.

SStay Alert. Do not operate this unit when you

are tired, ill, upset or under the influence of

alcohol, drugs, or medication. Watch what

you are doing; use common sense.

SWear hearing protection.

SNever start or run inside a closed room or

building. Breathing exhaust fumes can

kill.Keep handles free of oil and fuel.

SKeep handles free of oil and fuel.

SAlways keep engine on the right hand side

of your body.

SHold the unit firmly with both hands.Keep

trimmer head (or other optional attachment)

below waist level and away from all parts of

your body. Do not raise engine above your

waist.

SKeep all parts of your body away from muffler

and spinning line (or other optional

attachment). Keep engine below waist level.

A hot muffler can cause serious burns.

SKeep firm footing and balance. Do not

overreach or use from unstable surfaces

such as ladders, trees, steep slopes,

rooftops, etc.

SUse only in daylight or good artificial light.

SUse only for jobs explained in this manual

(or manuals for optional attachments).

UNIT / MAINTENANCE SAFETY

SDisconnect the spark plug before performing

maintenance except carburetor adjustments.

SLook for and replace damaged or loose parts

before each use. Look for and repair fuel

leaks before use. Keep in good working

condition.

SReplace trimmer head parts that are chipped,

cracked, broken, or damaged in any other

way before using the unit.

SMaintain unit according to recommended

procedures. Keep cutting line at proper

length.

SUse only 0.095″(2.4 mm) diameter Poulan

PRO brand line. Never use wire, rope, string,

etc.

SInstall required shield properly before using

the unit. Use only specified trimmer head;

make sure it is properly installed and securely

fastened.

SMake sure unit is assembled correctly as

shown in this manual.

SMake carburetor adjustments with lower end

supported to prevent line from contacting any

object.

SKeep others away when making carburetor

adjustments.

SUse only recommended Poulan PRO

accessories and replacement parts.

SHave all maintenance and service not

explained in this manual performed by an

authorized service dealer.

FUEL SAFETY

SMix and pour fuel outdoors.

SKeep away from sparks or flames.

SUse a container approved for fuel.

SDo not smoke or allow smoking near fuel or

the unit.

SAvoid spilling fuel or oil. Wipe up all fuel spills.

SMove at least 10 feet (3 meters) away from

fueling site before starting engine.

SStop engine and allow to cool before

removing fuel cap.

SAlways store gasoline in a container

approved for flammable liquids.

TRANSPORTING AND STORAGE

SAllow engine to cool; secure unit before

storing or transporting in vehicle.

SEmpty the fuel tank before storing or

transporting the unit. Use up fuel left in the

carburetor by starting the engine and letting it

run until it stops.

SStore unit and fuel in area where fuel vapors

cannot reach sparks or open flames from

water heaters, electric motors or switches,

furnaces, etc.

SStore unit so line limiter blade cannot

accidentally cause injury. The unit can be

hung by the shaft.

SStore unit out of reach of children.

WARNING: The engine exhaust

from this product contains chemicals known

to the State of California to cause cancer, birth

defects or other reproductive harm.

SAFETY NOTICE: Exposure to vibrations

through prolonged use of gasoline powered

hand tools could cause blood vessel or nerve

damage in the fingers, hands, and joints of

people prone to circulation disorders or abnor-

mal swellings. Prolonged use in cold weather

has been linked to blood vessel damage in

otherwise healthy people. If symptoms occur

such as numbness, pain, loss of strength,

change in skin color or texture, or loss of feeling

in the fingers, hands, or joints, discontinue the

use of this tool and seek medical attention. An

anti--vibration system does not guarantee the

avoidance of these problems. Users who oper-

ate power tools on a continual and regular basis

must monitor closely their physical condition

and the condition of this tool.

SPECIAL NOTICE: This unit is equipped

with a temperature limiting muffler and spark

arresting screen which meets the require-

ments of California Codes 4442 and 4443. All

U.S. forest land and the states of California,

Idaho, Maine, Minnesota, New Jersey, Ore-

gon, and Washington require by law that

many internal combustion engines be

equipped with a spark arresting screen. If you

operate in a locale where such regulations ex-

ist, you are legally responsible for maintaining

the operating condition of these parts. Failure

to do so is a violation of the law. For normal

homeowner use, the muffler and spark arrest-

ing screen will not require any service. After

50 hours of use, we recommend that your

muffler be serviced or replaced by your autho-

rized service dealer.

LINE TRIMMER SAFETY

WARNING: Inspect the area before

each use. Remove objects (rocks, broken

glass, nails, wire, etc.) which can be thrown

by or become entangled in line. Hard objects

can damage the trimmer head and be thrown

causing serious injury.

SUse only for trimming, scalping, mowing

and sweeping. Do not use for edging,

pruning or hedge trimming.

SCut from your left to your right. Cutting on

right side of the shield will throw debris

away from the operator.

ADDITIONAL SAFETY RULES

FOR OPTIONAL ATTACHMENTS

WARNING: For each optional at-

tachment used, read entire instruction manu-

al before use and follow all warnings and in-

structions in manual and on attachment.

WARNING: Ensure handlebar is

installed when using brushcutter attachment.

Attach handlebar above arrow on safety label

on the upper shaft (engine end of unit). If your

brushcutter attachment does not include a

handlebar, a handlebar accessory kit

(#530071451) is available from your autho-

rized service dealer.

Handlebar

EDGER SAFETY

WARNING: Inspect the area to be

edged before each use. Remove objects

(rocks, broken glass, nails, wire, etc.) which

can be thrown by the blade or can wrap

around the shaft.

WARNING: Blade rotates momen-

tarily after the trigger is released or engine is

turned off. The blade can seriously cut you or

others. Allow blade to stop before removing it

from the cut.

SThrow away blades that are bent, warped,

cracked, broken or damaged in any other

way. Replace parts that are cracked,

chipped, or damaged before using the unit.

SDo not attempt to remove cut material nor

hold material to be cut when the engine is

running or when cutting blade is moving.

SAlways keep the wheel and depth adjusting

skid in contact with the ground.

SAlways push the unit slowly over the

ground. Stay alert for uneven sidewalks,

holes in the terrain, large roots, etc.

BLOWER/VACUUM SAFETY

WARNING: Inspect area before

starting unit. Remove all debris and hard ob-

jects such as rocks, glass, wire, etc. that can

ricochet, be thrown, or otherwise cause injury

or damage during operation.

SDo not set unit on any surface except a clean,

hard area while engine is running. Debris

such as gravel, sand, dust, grass, etc., could

be picked up by the air intake and thrown out

through discharge opening, damaging unit,

property, or causing serious injury to

bystanders or operator.

SNever place objects inside the blower tubes,

vacuum tubes or blower outlet. Always direct

the blowing debris away from people,

animals, glass, and solid objects such as

trees, automobiles, walls, etc. The force of air

can cause rocks, dirt, or sticks to be thrown or

to ricochet which can hurt people or animals,

break glass, or cause other damage.

SNever run unit without the proper

equipment attached. When using your unit

as a blower, always install blower tubes.

SCheck air intake opening, blower tubes or

vacuum tubes frequently, always with

engine stopped and spark plug

disconnected. Keep vents and discharge

tubes free of debris which can accumulate

and restrict proper air flow.

SNever place any object in air intake opening

as this could restrict proper air flow and cause

damage to the unit.

SNever use for spreading chemicals, fertilizers,

or other substances which may contain toxic

materials.

STo avoid spreading fire, do not use near leaf or

brush fires, fireplaces, barbecue pits,

ashtrays, etc.

BRUSHCUTTER SAFETY

DANGER: Blade can thrust violently

away from material it does not cut. Blade

thrust can cause amputation of arms or legs.

WARNING: Do not use trimmer head

as a fastening device for the blade.

WARNING: The blade continues to

spin after the trigger is released or engine is

turned off. The coasting blade can throw ob-

jects or seriously cut you if accidentally

touched. Stop the blade by contacting the left

hand side of the coasting blade with material

already cut.

WARNING: Inspect the area to be

cut before each use. Remove objects (rocks,

broken glass, nails, wire, etc.) which can be

thrown or become entangled in the blade or

trimmer line.

SThrow away and replace blades that are

bent, warped, cracked, broken or damaged

in any other way.

SInstall required shield properly before using

the unit. Use the metal shield for all metal

blade use. Only use brushcutter attachments

that provide a metal shield with proboscis

nose.

Proboscis

nose

SUse only specified blade and make sure it is

properly installed and securely fastened.

SCut from your right to your left.

SAlways use the handlebar and a properly

adjusted shoulder strap with blade (see

ASSEMBLY instructions in brushcutter

attachment instruction manual).

CULTIVATOR SAFETY

WARNING: Rotating tines can cause

serious injury. Keep away from rotating tines.

Stop the engine and disconnect the spark plug

before unclogging tines or making repairs.

WARNING: Inspect the area to be

cultivated before starting the unit. Remove all

debris and hard and sharp objects such as

rocks, vines, branches, rope, string, etc.

SAvoid heavy contact with solid objects that

might stop the tines. If heavy contact occurs,

stop the engine and inspect the unit for

damage.

SNever operate the cultivator without the tine

cover in place and properly secured.

SKeep the tines and guard clear of debris.

SAfter striking a foreign object, stop the

engine, disconnect the spark plug and

inspect the cultivator for damage. Repair

before restarting.

SDisconnect attachment from the drive engine

before cleaning the tines with a hose and

water to remove any build--up. Oil the tines to

prevent rust.

SAlways wear gloves when servicing or

cleaning the tines. The tines become very

sharp from use.

SDo not run unit at high speed unless

cultivating.

HEDGE TRIMMER SAFETY

DANGER: RISK OF CUT; KEEP

HANDS AWAY FROM BLADE -- Blade moves

momentarily after the trigger is released or en-

gine is turned off. Do not attempt to clear away

cut material when the blade is in motion. Make

sure engine is turned off, the spark plug wire is

disconnected, and the blade has stopped mov-

ing before removing jammed material from the

cutting blade. Do not grab or hold the unit by the

cutting blade.

WARNING: Inspect the area before

starting the unit. Remove all debris and hard

objects such as rocks, glass, wire, etc. that

can ricochet, be thrown, or otherwise cause

injury or damage during operation.

SDo not use a cutting blade that is bent,

warped, cracked, broken or damaged in any

other way. Have worn or damaged parts

replaced by an authorized service dealer.

SAlways keep unit in front of your body.

Keep all parts of your body away from the

cutting blade.

SKeep the cutting blade and air vents clear of

debris.

POLE PRUNER SAFETY

WARNING: The reciprocating blade/

rotating chain can cause severe injury. In-

spect the unit before use. Do not operate unit

with a bent, cracked or dull blade or dull chain.

Keep away from the blade/chain.

WARNING: The reciprocating blade/

rotating chain is sharp. Do not touch. To pre-

vent serious injury, always stop engine and

ensure blade/chain has stopped moving, dis-

connect spark plug, and wear gloves when

changing or handling the blade or chain.

WARNING: A coasting blade/rotat-

ing chain can cause injury while it continues to

move after the engine is stopped. Maintain

proper control of the unit until the blade/chain

has completely stopped moving. Keep

hands, face and feet at a distance from all

moving parts. Do not attempt to touch or stop

the blade or chain when it is moving.

WARNING: Falling objects can

cause severe head injury. Wear head protec-

tion when operating this unit with a pole prun-

er attachment.

WARNING: To prevent serious injury,

do not use more than one boom extension with

a pole pruner attachment.

WARNING: Keep the pruner away

from power lines or electrical wires.

SOnly use for pruning limbs or branches

overhead up to 6 inches (15 cm) in diameter.

SDo not operate the unit faster than the

speed needed to prune. Do not run the unit

at high speed when not pruning.

SAlways stop the unit when work is delayed

or when walking from one cutting location to

another.

SIf you strike or become entangled with a

foreign object, stop the engine immediately

and check for damage. Have any damage

repaired by an authorized service dealer

before attempting further operations.

Discard blades that are bent, warped,

cracked or broken.

SStop the unit immediately if you feel excessive

vibration. Vibration is a sign of trouble. Inspect

thoroughly for loose nuts, bolts or damage

before continuing. Contact an authorized

service dealer for repair or replacement of

affected parts as necessary.

SNOW THROWER SAFETY

WARNING: Keep hands and feet

away from the rotor when starting or running

the engine. Never attempt to clear the rotor

with the engine/motor running. Stop engine

and disconnect spark plug before unclogging

snow or debris from discharge chute or when

adjusting vanes.

WARNING: Never lean over dis-

charge chute. Rocks or debris could be

thrown into the eyes and face and cause seri-

ous injury or blindness.

WARNING: Inspect the area where

the unit is to be used. Remove objects that

could be thrown or damage the unit. Some

objects may be hidden by fallen snow -- be

alert for the possibility.

SDirect material discharge away from glass

enclosures, automobiles, etc.

SDo not run engine at high speed while not

removing snow.

SBe attentive when using the snowthrower,

and stay alert for holes in the terrain and other

hidden hazards.

SMake sure the rotor will spin freely before

attaching the snowthrower to the powerhead.

SIf the rotor will not rotate freely due to frozen

ice, thaw the unit before thoroughly before

attempting to operate under power.

SKeep the rotor clear of debris.

SDo not throw snow near other people. The

snow thrower could propel small objects at

high speed causing injury.

SAfter striking a foreign object, stop the

engine, disconnect spark plug and inspect

the snowthrower for damage and repair if

necessary before restarting unit.

SNever operate the snowthrower near glass

enclosures, automobiles and trucks.

SNever attempt to use the snowthrower on a

roof.

SNever operate the snowthrower near

window wells, dropoffs, etc.

SNever discharge snow onto public roads or

near moving traffic.

SClear snow from slopes by going up and

down; never across. Use caution when

changing directions. Never clear snow from

steep slopes.

SLet snowthrower run for a few minutes after

clearing snow so moving parts do not

freeze.

SLook behind and use care when backing up.

Exercise caution to avoid slipping or falling,

especially when operating in reverse.

SKnow how to stop quickly.

ASSEMBLY

WARNING: If received assembled,

repeat all steps to ensure your unit is properly

assembled and all fasteners are secure.

Examine parts for damage. Do not use dam-

aged parts.

NOTE: If you need assistance or find parts

missing or damaged, call 1-800-554-6723.

It is normal for the fuel filter to rattle in the

empty fuel tank.

Finding fuel or oil residue on muffler is normal

due to carburetor adjustments and testing

done by the manufacturer.

INSTALLING TRIMMER ATTACH-

MENT

CAUTION: When installing trimmer attach-

ment, place the unit on a flat surface for stabil-

ity.

1. Loosen the coupler by turning the knob

counterclockwise.

Coupler

Knob

LOOSEN

TIGHTEN

Shipping

protector

2. Remove shipping protector from coupler.

3. Remove the shaft cap from the trimmer at-

tachment (if present).

4. Position locking/release button of attach-

ment into guide recess of coupler.

5. Push the attachment into the coupler until

the locking/release button snaps into the

primary hole.

6. Before using the unit, tighten the knob se-

curely by turning clockwise.

Coupler Primary Hole

Upper

Shaft

Locking/

Release

Button

Lower

Attachment

Guide Recess

WARNING: Make sure the locking/

release button is locked in the primary hole

and the knob is securely tightened before op-

erating the unit. All attachments are designed

to be used in the primary hole unless otherwise

stated in the applicable attachment instruction

manual. Using the wrong hole could lead to seri-

ous injury or damage to the unit.

Locking/Release

Button in Primary Hole

For assembly of optional attachments (see

list on page 11), refer to the ASSEMBLY sec-

tion of the applicable attachment instruction

manual.

ATTACHING THE SHIELD

WARNING: The shield must be prop-

erly installed. The shield provides partial protec-

tion from the risk of thrown objects to the opera-

tor and others and is equipped with a line limiter

blade which cuts excess line to the proper

length. The line limiter blade (on underside of

shield) is sharp and can cut you.

For proper orientation of shield, see KNOW

YOUR TRIMMER illustration in OPERATION

section.

1. Remove wing nut from shield.

2. Insert bracket into slot as shown.

3. Pivot shield until bolt passes through hole in

bracket.

4. Securely tighten wing nut onto bolt.

Wing Nut

Bracket

Slot

Shield Gearbox

ADJUSTING THE HANDLE

WARNING: When adjusting the han-

dle, be sure it remains above the safety label

and below the mark or arrow on the shaft.

1. Loosen wing nut on handle.

2. Rotate the handle on the shaft to an up-

right position; retighten wing nut.

OPERATION

KNOW YOUR UNIT

READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT.

Compare the illustrations with your unit to familiarize yourself with the location of the various controls

and adjustments. Save this manual for future reference.

Line Limiter

Blade

Primer Bulb

Assist Handle

Throttle Trigger

Start

Lever

Spark

Plug

Shield

Trimmer

Head Shaft

Muffler

ON/STOP

Switch

Coupler

Starter handle

ON/STOP SWITCH

The ON/STOP switch is located on the trigger

handle and is used to stop the engine. To stop

the engine, push and release the engine

ON/STOP switch.

PRIMER BULB

The PRIMER BULB removes air from the car-

buretor and fuel lines and fills them with fuel.

This allows you to start the engine with fewer

pulls on the starter rope. Activate the primer

bulb by pressing it and allowing it to return to

its original form.

START LEVER

The START LEVER helps to supply fuel to the

engine to aid in starting. Activate the starting

system by moving the start lever to the START

position. DO NOT squeeze the throttle trigger

until the engine has started and runs. After the

engine starts, allow the engine to warm--up

10--15 seconds, then fully squeeze the throttle

trigger to deactivate the starting system.

COUPLER

The COUPLER enables optional attach-

ments to be installed on the unit.

BEFORE STARTING ENGINE

WARNING: Be sure to read the fuel

information in the safety rules before you be-

gin. If you do not understand the safety rules,

do not attempt to fuel your unit. Call

1-800-554-6723.

FUELING ENGINE

WARNING: Remove fuel cap slowly

when refueling.

HELPFUL TIP

To obtain the correct oil mix

ratio, pour 3.2 ounces of

2--cycle synthetic oil into

one gallon of fresh gas.

This engine is certified to operate on un-

leaded gasoline. Before operation, gasoline

must be mixed with a good quality synthetic

2-cycle air-cooled engine oil designed to be

mixed at a ratio of 40:1. Poulan/WEED EATER

brand synthetic oil is recommended. Mix gaso-

line and oil at a ratio of 40:1. A 40:1 ratio is ob-

tained by mixing 3.2 ounces (95 ml) of oil with 1

gallon (4 liters) of unleaded gasoline. DO NOT

USE automotive oil or marine oil. These oils

will cause engine damage. When mixing fuel,

follow instructions printed on container. Once

oil is added to gasoline, shake container mo-

mentarily to assure that the fuel is thoroughly

mixed. Always read and follow the safety

rules relating to fuel before fueling your unit.

CAUTION: Never use straight gasoline in

your unit. This will cause permanent engine

damage and void the limited warranty.

FUEL REQUIREMENTS

This engine requires the use of minimum 87

octane [R+M]/2 clean gasoline.

IMPORTANT

Use of alcohol blended fuels (called gasohol or

using ethanol or methanol) can cause major en-

gine performance and durability problems.

WARNING: Alternative fuels (not gas-

oline) such as E--15 (15% alcohol), E--20 (20%

alcohol), E--85 (85% alcohol) are NOT classified

as gasoline and are NOT approved for use in

2--stroke gasoline engines. Use of alternative

fuels will cause problems such as: improper

clutch engagements, overheating, vapor lock,

power loss, lubrication deficiency, deterioration

of fuel lines, gaskets and internal carburetor

components, etc. Alternative fuels cause high

moisture absorption into the fuel/oil mixture

leading to oil and fuel separation.

HOW TO STOP YOUR UNIT

SRelease the throttle trigger.

SPush and release the engine ON/STOP

switch. The switch will automatically return to

the ON position. Wait 5 seconds before at-

tempting to restart unit to allow switch to reset.

ON/STOP

Switch

HOW TO START YOUR UNIT

WARNING: Avoid any contact with

the muffler. A hot muffler can cause serious

burns.

Starting position

HELPFUL TIP

If your engine still does not

start after following these

instructions, please call

1--800--554--6723.

STARTINGACOLDENGINE

NOTE: DO NOT squeeze the throttle trigger

until the engine has started and runs.

1. Set unit on a flat surface.

2. Slowly press the primer bulb 6 times.

3. Move the start lever to the START position.

Primer Bulb

Start Lever

Starter Handle

4. Pull starter rope handle sharply until en-

gine starts and runs.

5. Allow unit to run for 10--15 seconds, then

fully squeeze the throttle trigger to disen-

gage the starting system.

STARTING A WARM ENGINE

1. Squeeze and hold the throttle trigger.

Keep throttle trigger fully squeezed until

engine runs smoothly.

2. Pull starter rope sharply while squeezing

throttle trigger until engine runs.

NOTE: Normally, the warm starting proce-

dure can be used within 5--10 minutes after

the unit is turned off. If the unit sits for more

than 10 minutes without being ran, it will be

necessary to start the unit by following the

steps under STARTING A COLD ENGINE or

following the starting instruction steps shown

on the unit.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing

the start lever to the RUN position. Fully

squeeze throttle trigger. Pull the starter han-

dle repeatedly while squeezing throttle trigger

until engine starts and runs. This could re-

quire pulling the starter handle many times,

depending on how badly the unit is flooded.

If the unit still doesn’t start, refer to

TROUBLESHOOTING TABLE or call

1-800-554-6723.

OPERATING THE COUPLER

This model is equipped with a coupler which

enables optional attachments to be installed.

The optional attachments are: MODEL:

Edger PP1000E.....................

Cultivator PP2000T..................

Blower PP3000B....................

Brushcutter PP4000C................

Pruner PP5000P....................

WARNING: Always stop unit and dis-

connect spark plug before removing or instal-

ling attachments.

REMOVING TRIMMER ATTACH-

MENT (OR OTHER OPTIONAL

ATTACHMENTS)

CAUTION: When removing or installing at-

tachments, place the unit on a flat surface for

stability.

1. Loosen the coupler by turning the knob

counterclockwise.

Coupler

Knob

LOOSEN

TIGHTEN

Upper

Shaft

Lower

Attachment

2. Press and hold the locking/release button.

ocking

Release

Button

Coupler Upper Shaft

Lower Attachment

3. While securely holding the engine and

upper shaft, pull the attachment straight

out of the coupler.

INSTALLING OPTIONAL ATTACH-

MENTS

1. Remove the shaft cap from the attach-

ment (if present).

2. Position locking/release button of attach-

ment into guide recess of coupler.

3. Push the attachment into the coupler until

the locking/release button snaps into the

primary hole.

4. Before using the unit, tighten the knob se-

curely by turning clockwise.

Coupler Primary Hole

Upper

Shaft

Locking/

Release

Button

Attachment

Guide Recess

WARNING: Make sure the locking/

release button is locked in the primary hole

and the knob is securely tightened before op-

erating the unit. All attachments are designed

to be used in the primary hole unless otherwise

stated in the applicable attachment instruction

manual. Using the wrong hole could lead to seri-

ous injury or damage to the unit.

Locking/Release

Button in Primary Hole

OPERATING INSTRUCTIONS

It is recommended that the engine not be

operated for longer than 1 minute at full

throttle.

OPERATING POSITION

Cut onl

rom

our le

tto

our ri

ht.

ALWAYS WEAR:

Long Pants

Heavy shoes

Eye Protection

Hearing

Protection

WARNING: Always wear eye protec-

tion. Never lean over the trimmer head.

Rocks or debris can ricochet or be thrown into

eyes and face and cause blindness or other

serious injury.

When operating unit, stand as shown and

check for the following:

SWear eye protection and heavy clothing.

SHold trigger handle with your right hand and

assit handle with left hand.

SKeep unit below waist level.

SCut only from your left to your right to

ensure debris is thrown away from you.

Without bending over, keep line near and

parallel to the ground and not crowded into

material being cut.

Do not run the engine at a higher speed than

necessary. The cutting line will cut efficiently

when the engine is run at less than full throttle.

At lower speeds, there is less engine noise and

vibration. The cutting line will last longer and will

be less likely to “weld” onto the spool.

Always release the throttle trigger and allow

the engine to return to idle speed when not

cutting.

To stop engine:

SRelease the throttle trigger.

SPush and release the engine ON/STOP

switch.

TRIMMER LINE ADVANCE

The trimmer line will advance approximately 2

inches (5 cm) each time the bottom of the

trimmer head is tapped on the ground with the

engine running at full throttle.

The most efficient line length is the maximum

length allowed by the line limiter. Always keep

the shield in place when the tool is being oper-

ated.

To advance line:

SOperate the engine at full throttle.

SHold the trimmer head parallel to and above

the grassy area.

STap the bottom of the trimmer head lightly on

the ground one time. Approximately 2 inches

(5cm)oflinewillbeadvancedwitheachtap.

Always tap the trimmer head on a grassy area.

Tapping on surfaces such as concrete or as-

phalt can cause excessive wear to the trimmer

head.If the line is worn down to 2 inches (5 cm)

or less, more than one tap will be required to ob-

tain the most efficient line length.

WARNING: Use only 0.095″(2.4

mm) diameter line. Other sizes of line will not

advance properly and can cause serious

injury. Do not use other materials such as

wire, string, rope, etc. Wire can break off dur-

ing cutting and become a dangerous missile

that can cause serious injury.

CUTTING METHODS

WARNING: Use minimum speed

and do not crowd the line when cutting around

hard objects (rock, gravel, fence posts, etc.),

which can damage the trimmer head, become

entangled in the line, or be thrown causing a

serious hazard.

SThe tip of the line does the cutting. You will

achieve the best performance and mini-

mum line wear by not crowding the line into

the cutting area. The right and wrong ways

are shown below.

Tip of the line

does the cutting.

Right Wrong

Line crowded into

work area.

SThe line will easily remove grass and

weeds from around walls, fences, trees and

flower beds, but it also can cut the tender

bark of trees or shrubs and scar fences.

SFor trimming or scalping, use less than full

throttle to increase line life and decrease

head wear, especially:

SDuring light duty cutting.

SNear objects around which the line can wrap

such as small posts, trees or fence wire.

SFor mowing or sweeping, use full throttle for

a good clean job.

TRIMMING -- Hold the bottom of the trimmer

head about 3 inches (8 cm) above the ground

and at an angle. Allow only the tip of the line to

make contact. Do not force trimmer line into

work area.

Trimming

3 inches (8 cm)

above ground

SCALPING -- The scalping technique removes

unwanted vegetation down to the ground. Hold

the bottom of the trimmer head about 3 in. (8

cm) above the ground and at an angle. Allow the

tip of the line to strike the ground around trees,

posts, monuments, etc. This technique in-

creases line wear.

Scalping

MOWING -- Your trimmer is ideal for mowing

in places conventional lawn mowers cannot

reach. In the mowing position, keep the line

parallel to the ground. Avoid pressing the

head into the ground as this can scalp the

ground and damage the tool.

Mowing

SWEEPING -- The fanning action of the rotat-

ing line can be used to blow away loose debris

from an area. Keep the line parallel to and

above the area surface and swing the tool

from side to side. Sweeping

MAINTENANCE

WARNING: Disconnect the spark

plug before performing maintenance except

for carburetor adjustments.

HELPFUL TIP

IMPORTANT: Have all

repairs other than the rec-

ommended maintenance

described in the instruction

manual performed by an

authorized service dealer.

If any dealer other than an authorized

service dealer performs work on the

product, Poulan PRO may not pay for

repairs under warranty. It is your re-

sponsibility to maintain and perform

general maintenance.

CHECK FOR LOOSE

FASTENERS AND PARTS

SSpark Plug Boot

SAir Filter

SHousing Screws

SAssist Handle Screw

SDebris Shield

CHECK FOR DAMAGED OR

WORN PARTS

Contact an authorized service dealer for re-

placement of damaged or worn parts.

SON/STOP Switch -- Ensure ON/STOP

switch functions properly by pushing and

releasing the switch. Make sure engine

stops. Wait 5 seconds before attempting to

restart unit to allow switch to reset. Restart

engine and continue.

SFuel Tank -- Discontinue use of unit if fuel

tank shows signs of damage or leaks.

SDebris Shield -- Discontinue use of unit if

debris shield is damaged.

INSPECT AND CLEAN UNIT AND DE-

CALS

SAfter each use, inspect complete unit for

loose or damaged parts. Clean the unit and

decals using a damp cloth with a mild deter-

gent.

SWipe off unit with a clean dry cloth.

CLEAN AIR FILTER

A dirty air filter decreases engine perform-

ance and increases fuel consumption and

harmful emissions. Always clean after every

5 hours of operation.

1. Clean the cover and the area around it to

keep dirt from falling into the carburetor

chamber when the cover is removed.

2. Remove parts by pressing button to re-

lease air filter cover.

NOTE: To avoid creating a fire hazard or

producing harmful evaporative emissions, do

not clean filter in gasoline or other flammable

solvent.

3. Wash the filter in soap and water.

4. Allow filter to dry.

5. Replace parts.

Button

Air Filter Cover

Air Filter

INSPECT MUFFLER AND SPARK

ARRESTING SCREEN

WARNING: The muffler on this prod-

uct contains chemicals known to the State of

California to cause cancer.

As your unit is used, carbon deposits build up

on the muffler and spark arresting screen and

must be removed to avoid creating a fire haz-

ard or affecting engine performance.

For normal homeowner use, the muffler and

spark arresting screen will not require any

service. After 50 hours of use, we recom-

mend that your muffler be serviced or re-

placed by an authorized service dealer.

REPLACE SPARK PLUG

Replace the spark plug each year to ensure

the engine starts easier and runs better. Set

spark plug gap at 0.025 inch (0.6 mm). Igni-

tion timing is fixed and nonadjustable.

1. Twist, then pull off spark plug boot.

2. Remove spark plug from cylinder and

discard.

3. Replace with Champion RCJ-6Y spark

plug and tighten securely with a 3/4 inch

(19 mm) socket wrench.

4. Reinstall the spark plug boot.

SERVICE AND ADJUSTMENTS

REPLACING THE LINE

1. Press the tabs on the side of the trimmer

head and remove cover and spool.

Tab

Cover

Ta p B u t t o n

2. Remove any remaining line.

3. Clean dirt and debris from all parts. Re-

place spool if it is worn or damaged.

4. Replace with a pre-wound spool, or re-

place line using a 15 feet (4.5 meters)

length of 0.095 inch (2.4 mm) diameter

Poulan PRO brand line.

5. When installing new line on an existing

spool, hold the spool as shown in the il-

lustration below.

6. Bend the line at the midpoint and insert

the bend into the slot in the center rim of

the spool. Ensure line snaps into position

in the slot.

Slot

Spool

7. With your finger between the lines, wrap

the lines evenly and firmly around the

spool in a clockwise direction.

8. Position the lines in the guide slots.

Guide

Slot

Guide Slot

9. Insert the ends of the lines through exit

holes in the sides of the cover.

10. Place the spool in the cover.

Spool

Cover

11. Make sure the lines are not caught be-

tween the rim of the spool and the wall of

the cover.

12. Reinstall the spool and cover onto the

trimmer head. Push until cover snaps into

place.

REPLACING THE CUTTING HEAD

1. Align hole in the dust cup with the hole in

the side of the gearbox by rotating the

dust cup.

2. Insert a small screwdriver into aligned

holes. This will keep the shaft from turning

while removing and installing trimmer head.

Screwdriver

3. While holding the screwdriver in position,

remove trimmer head by turning clockwise.

4. Thread replacement trimmer head onto

the shaft by turning counterclockwise.

Tighten until secure.

5. Remove the screwdriver.

CARBURETOR IDLE SPEED

ADJUSTMENT

WARNING: Keep others away when

making idle speed adjustments. The trimmer

head, blade or any optional attachment will be

spinning during most of this procedure. Wear

your protective equipment and observe all safe-

ty precautions. After making adjustments, the

trimmer head, blade or any optional attachment

must not move/spin at idle speed.

The carburetor has been carefully set at the

factory. Adjustments may be necessary if you

notice any of the following conditions:

SEngine will not idle when the throttle is

released.

SThe trimmer head, blade or optional

attachment moves/spins at idle.

Make adjustments with the unit supported so

the cutting attachment is off the ground and

will not make contact with any object. Hold

the unit by hand while running and making ad-

justments. Keep all parts of your body away

from the cutting attachment and muffler.

To adjust idle speed:

Allow engine to idle. Adjust speed until engine

runs without trimmer head, blade or optional

attachment moving or spinning (idle too fast)

or stalling (idle speed too slow).

STurn idle speed screw clockwise to

increase engine speed if engine stalls or

dies.

STurn idle speed screw counterclockwise to

decrease engine speed if trimmer head,

blade or optional attachment moves or

spins at idle.

WARNING: Recheck the idle speed

after each adjustment. The trimmer head,

blade or optional attachment must not move

or spin at idle speed to avoid serious injury to

the operator or others.

Idle Speed Screw

Air Filter Cover

If you require further assistance or are unsure

about performing this procedure, contact an

authorized service dealer or call

1--800--554--6723.

STORAGE

WARNING: Perform the following

steps after each use:

SAllow engine to cool before storing or trans-

porting.

SStore unit and fuel in a well ventilated area

where fuel vapors cannot reach sparks or

open flames from water heaters, electric

motors or switches, furnaces, etc.

SStore unit with all guards in place. Position

unit so that any sharp object cannot acci-

dentally cause injury.

SStore unit and fuel well out of the reach of

children.

SEASONAL STORAGE

Prepare unit for storage at end of season or if

it will not be used for 30 days or more.

If your unit is to be stored for a period of time:

SClean the entire unit before lengthy

storage.

SStore in a clean dry area.

SLightly oil external metal surfaces.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA-

TION section of this manual, see message la-

beled IMPORTANT regarding the use of ga-

sohol in your engine.

Fuel stabilizer is an acceptable alternative in

minimizing the formation of fuel gum deposits

during storage. Add stabilizer to the gasoline

in the fuel tank or fuel storage container.

Follow the mix instructions found on stabilizer

container. Run engine at least 5 minutes after

adding stabilizer.

HELPFUL TIP

During storage of your gas/

oil mixture, the oil will sepa-

rate from the gas.

We recommend that you

shake the gas can weekly

to insure proper blending of

the gas and oil.

ENGINE

SRemove spark plug and pour 1 teaspoon of

40:1, 2-cycle engine oil (air cooled) through

the spark plug opening. Slowly pull the

starter rope 8 to 10 times to distribute oil.

SReplace spark plug with new one of recom-

mended type and heat range.

SClean air filter.

SCheck entire unit for loose screws, nuts,

and bolts. Replace any damaged, broken,

or worn parts.

SAt the beginning of the next season, use

only fresh fuel having the proper gasoline to

oil ratio.

OTHER

SDo not store gasoline from one season to

another.

SReplace your gasoline can if it starts to rust.

TROUBLE CAUSE REMEDY

Engine will not

start.

1. Engine flooded.

2. Fuel tank empty.

3. Spark plug not firing.

4. Fuel not reaching

carburetor.

5. Carburetor requires

adjustment.

1. See “Starting a Flooded Engine” in

Operation Section.

2. Fill tank with correct fuel mixture.

3. Install new spark plug.

4. Check for dirty fuel filter; replace.

Check for kinked or split fuel line;

repair or replace.

5. Contact an authorized service dealer.

Engine will

not idle

properly.

1. Carburetor requires

adjustment.

2. Crankshaft seals worn.

3. Compression low.

1. See “Carburetor Idle Speed Adjustment”

in Service and Adjustments Section.

2. Contact an authorized service dealer.

3. Contact an authorized service dealer.

1. Air filter dirty.

2. Spark plug fouled.

3. Carburetor requires

adjustment.

4. Carbon build-up on

muffler outlet screen.

5. Compression low.

Engine will not

accelerate,

lacks power,

or dies under

a load.

1. Clean or replace air filter.

2. Clean or replace plug

and regap.

3. Contact an authorized service dealer.

4. Contact an authorized service dealer.

5. Contact an authorized service dealer.

Engine

smokes

excessively.

1. Fuel mixture incorrect.

2. Air filter dirty.

3. Carburetor requires

adjustment.

1. Empty fuel tank and refill with

correct fuel mixture.

2. Clean or replace air filter.

3. Contact an authorized service dealer.

Engine runs

hot.

1. Fuel mixture incorrect.

2. Spark plug incorrect.

3. Carburetor requires

adjustment.

4. Carbon build-up on

muffler outlet screen.

1. See “Fueling Engine” in Operation

section.

2. Replace with correct spark plug.

3. Contact an authorized service dealer.

4. Contact an authorized service dealer.

WARNING: Always stop unit and disconnect spark plug before performing all of the

recommended remedies below except remedies that require operation of the unit.

TROUBLESHOOTING TABLE

LIMITED WARRANTY

Poulan PRO, a division of Husqvarna Consum-

er Outdoor Products N.A., Inc., warrants to the

original consumer purchaser that each new

Poulan PRO brand gasoline tool or attachment

is free from defects in material and workman-

ship and agrees to repair or replace under this

warranty any defective gasoline product or at-

tachment as follows from the original date of

purchase.

2YEARS--Parts and Labor, when used for

household purposes.

90 DAYS -- Parts and Labor, when used for

commercial, professional, or income producing

purposes.

30 DAYS -- Parts and Labor, if used for rental

purposes.

This warranty is not transferable and does not

cover damage or liability caused by improper

handling, improper maintenance or alteration, or

the use of accessories and/or attachments not

specifically recommended by Poulan PRO for

this tool. This warranty does not cover tune--up,

spark plugs, filters, starter ropes, cutting line, or

rotating head parts that will wear and require re-

placement with reasonable use during the war-

ranty period. This warranty does not cover pre--

delivery setup or normal adjustments explained

in the instruction manual. This warranty does

not cover transportation costs.

In the event you have a claim under this warran-

ty, you must return the product to an authorized

service dealer.

Should you have any unanswered questions

concerning this warranty, please contact:

Poulan PRO, a division of Husqvarna

Consumer Outdoor Products N.A., Inc.

1030 Stevens Creek Road

Augusta, GA 30907

1--800--554--6723

In Canada, contact:

Poulan PRO

850 Matheson Blvd. West

Mississauga, Ontario L5V 0B4

Giving the model number, serial number and

date of purchase of your product and the name

and address of the authorized dealer from

whom it was purchased.

THIS WARRANTY GIVES YOU SPECIFIC

LEGAL RIGHTS, AND YOU MAY HAVE OTH-

ER RIGHTS WHICH VARY FROM STATE TO

STATE.

NO CLAIMS FOR CONSEQUENTIAL OR

OTHER DAMAGES WILL BE ALLOWED,

AND THERE ARE NO OTHER EXPRESS

WARRANTIES EXCEPT THOSE EX-

PRESSLY STIPULATED HEREIN.

SOME STATES DO NOT ALLOW LIMITA-

TIONS ON HOW LONG AN IMPLIED WAR-

RANTY LASTS OR THE EXCLUSION OR

LIMITATIONS OF INCIDENTAL OR CONSE-

QUENTIAL DAMAGES, SO THE ABOVE LIM-

ITATIONS OR EXCLUSION MAY NOT APPLY

TO YOU.

This is a limited warranty within the meaning of

that term as defined in the Magnuson--Moss Act

of 1975.

The policy of Poulan PRO is to continuously

improve its products. Therefore, Poulan PRO

reserves the right to change, modify, or dis-

continue models, designs, specifications,

and accessories of all products at any time

without notice or obligation to any purchaser.

U.S. EPA / CALIFORNIA / ENVIRONMENT CANADA

EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OB-

LIGATIONS: The U.S. Environmental

Protection Agency, California Air Resources

Board, Environment Canada and Poulan

PRO are pleased to explain the emissions con-

trol system warranty on your year 2009 and lat-

er small off--road engine. In California, all small

off--road engines must be designed, built, and

equipped to meet the State’s stringent anti--

smog standards. Poulan PRO must warrant

the emission control system on your small

off--road engine for the periods of time listed

below provided there has been no abuse, ne-

glect, or improper maintenance of your small

off--road engine. Your emission control system

includes parts such as the carburetor, the igni-

tion system and the fuel tank. Where a warrant-

able condition exists, Poulan PRO will repair

your small off--road engine at no cost to you.

Expenses covered under warranty include

diagnosis, parts and labor. MANUFACTUR-

ER’S WARRANTY COVERAGE: If any

emissions related part on your engine (as

listed under Emissions Control Warranty Parts

List) is defective or a defect in the materials or

workmanship of the engine causes the failure of

such an emission related part, the part will be re-

paired or replaced by Poulan PRO. OWNER’S

WARRANTY RESPONSIBILITIES: As the

small off--road engine owner, you are respon-

sible for the performance of the required

maintenance listed in your instruction manu-

al. Poulan PRO recommends that you retain

all receipts covering maintenance on your

small off--road engine, but Poulan PRO can-

not deny warranty solely for the lack of re-

ceipts or for your failure to ensure the perfor-

mance of all scheduled maintenance. As the

small off--road engine owner, you should be

aware that Poulan PRO may deny you war-

ranty coverage if your small off--road engine

or a part of it has failed due to abuse, neglect,

improper maintenance, unapproved modifi-

cations, or the use of parts not made or ap-

proved by the original equipment manufactur-

er. You are responsible for presenting your

smalloff--roadenginetoanPoulanPROautho-

rized repair center as soon as a problem exists.

Warranty repairs should be completed in a rea-

sonable amount of time, not to exceed 30 days.

If you have any questions regarding your war-

ranty rights and responsibilities, you should

contact your nearest authorized service center,

call Poulan PRO at 1--800--554--6723, or send

e-mail correspondence to emission.warran-

ty@HCOP--emission.com.WARRANTY

COMMENCEMENT DATE: The warranty pe-

riod begins on the date the small off--road en-

gine is purchased. LENGTH OF COVER-

AGE: This warranty shall be for a period of

two years from the initial date of purchase.

WHAT IS COVERED: REPAIR OR RE-

PLACEMENT OF PARTS. Repair or re-

placement of any warranted part will be per-

formed at no charge to the owner at an

approved Poulan PRO servicing center. If

you have any questions regarding your war-

ranty rights and responsibilities, you should

contact your nearest authorized service cen-

ter, call Poulan PRO at 1--800--554--6723, or

send e-mail correspondence to emis-

sion.warranty@HCOP--emission.com.

WARRANTY PERIOD: Any warranted part

which is not scheduled for replacement as re-

quired maintenance, or which is scheduled

only for regular inspection to the effect of “re-

pair or replace as necessary” shall be war-

ranted for 2 years. Any warranted part which

is scheduled for replacement as required

maintenance shall be warranted for the period

of time up to the first scheduled replacement

point for that part. DIAGNOSIS: The owner

shall not be charged for diagnostic labor

which leads to the determination that a war-

ranted part is defective if the diagnostic work

is performed at an approved Poulan PRO

servicing center. CONSEQUENTIAL DAM-

AGES: Poulan PRO may be liable for dam-

ages to other engine components caused by

the failure of a warranted part still under war-

ranty. WHAT IS NOT COVERED: All failures

caused by abuse, neglect, or improper main-

tenance are not covered. ADD--ON OR MO-

DIFIED PARTS: The use of add--on or modi-

fied parts can be grounds for disallowing a

warranty claim. Poulan PRO is not liable to

cover failures of warranted parts caused by

the use of add--on or modified parts. HOW TO

FILE A CLAIM: If you have any questions re-

garding your warranty rights and responsibili-

ties, you should contact your nearest autho-

rized service center, call Poulan PRO at

1--800--554--6723, or send e-mail correspon-

dence to emission.warranty@ HCOP--

emission.com.WHERE TO GET WARRAN-

TY SERVICE: Warranty services or repairs

shall be provided at all Poulan PRO service

centers. Call: 1--800--554--6723 or send

e-mail correspondence to emission. warran-

ty@HCOP--emission.com.MAINTE-

NANCE, REPLACEMENT AND REPAIR

OF EMISSION RELATED PARTS: Any Pou-

lan PRO approved replacement part used in

the performance of any warranty mainte-

nance or repair on emission related parts will

be provided without charge to the owner if the

part is under warranty. EMISSION CON-

TROL WARRANTY PARTS LIST: Carbure-

tor, air filter (covered up to maintenance sched-

ule), ignition system: spark plug (covered up to

maintenance schedule), ignition module, muffler

including catalyst (if equipped), fuel tank.

MAINTENANCE STATEMENT: The owner is

responsible for the performance of all re-

quired maintenance as defined in the instruc-

tion manual.

The information on the product label indicates which standard your engine is certified.

Example: (Year) EPA and/or CALIFORNIA.

This engine is certified to be emissions compliant for the following use:

Moderate (50 hours)

Intermediate (125 hours)

Extended (300 hours)

Poulan Pro 952711962 User manual

Brand: Poulan Pro

Model: 952711962

Category: Grass trimmers

Type: User manual

Download PDF

report

Poulan Pro 952711962 User manual

Poulan Pro 952711962 User manual

Related papers

Other documents