Page is loading ...
Bersheart LLC
3500 West Hallandale Beach Blvd
Pembroke Park, FL 33023
www.martinobymartinocartier.com
(800) 327-7971
HAUTE STUFF AIR
Featherlight Ionic Professional Dryer
Styling Guide & User Manual
MC121_UserGuide.indd Spread 1 of 8 - Pages(16, 1)MC121_UserGuide.indd Spread 1 of 8 - Pages(16, 1) 8/6/15 8:56 AM8/6/15 8:56 AM
Designed with everyone in mind, this featherlight, ergonomic dryer is
great to hold, weighing in at less than 1 lb. Haute Stuff Air features
a 1800W motor that packs the power to sustain exceptional airfl ow,
which reduces drying time and heat exposure to the hair. Ionic
technology aids in breaking up water quickly through the emission of
negative ions that smooth hair, reduce drying time and increase shine.
Healthy looking, frizz-free, hydrated hair is a result of moisture being
sealed within the cuticle of the hair. Eff ortless styling in half the time.
Before using this product, please read these instructions carefully.
Refer to the Caution/Warning Section for important information.
For further instructions, please visit
www.martinobymartinocartier.com/tools.
1
introduction
IMPORTANT SAFEGUARD
WARNING - To reduce risk of burns, electrocution, fi re or injury to persons:
1. An appliance should never be left unattended when plugged in.
2. Close supervision is necessary when this appliance is used by, on, or near children or individuals with certain
disabilities.
3. Use this tool only for it’s intended use as described in this manual. Do not use attachments not recommended by
the manufacturer.
4. Never operate this tool if it has a damaged cord or plug, if it is not working properly, or if it has been dropped,
damaged, or dropped into water. Return the appliance to a service center for examination and repair.
5. Keep the cord away from heated surfaces. Do not wrap the cord around the hair dryer. Do not place appliance on
any surface while it is hot or plugged in.
6. Never block the air openings of the appliance or place it on a soft surface such as a bed or sofa, where the openings
may be blocked. Keep airfl ow free of lint, hair and dust.
7. Do not use a voltage converter with hair dryer.
8. Never use while sleeping.
9. Do not use outdoors or operate near where aerosol (spray) products are being used or where oxygen is being
administered.
10. While using the dryer, keep your hair away from air inlets.
11. Never drop or insert any object into any opening or hose.
12. NEVER use the device in water or other liquids. NEVER use the device near a bathtub, shower, containers full of
water, or any other damp place. Never use it with bare feet or when hands and feet are wet.
13. Do not use the appliance for any other purpose than it’s intended use.
14. Do not direct hot air toward eyes or other heat sensitive areas.
15. Do not place appliance on any surface while it is operating.
16. Do not use extension cord with this appliance.
17. Attachments may be hot during use. Allow them to cool before handling.
Save these instructions.
WARNING- DO NOT IMMERSE OR
USE WHILE BATHING.
warning
14
“UNPLUG IT”
DO NOT REMOVE THIS TAG!
WARN CHILDREN OF THE RISK
OF DEATH BY ELECTRIC SHOCK!
5001688
MC121_UserGuide.indd Spread 2 of 8 - Pages(2, 15)MC121_UserGuide.indd Spread 2 of 8 - Pages(2, 15) 8/6/15 8:56 AM8/6/15 8:56 AM
safety
IF YOU MUST USE YOUR HAIR DRYER IN
THE BATHROOM, INSTALL A GFCI* NOW!
Your local electrician can help you decide which type
is best for you -- A portable unit that plugs into the
electrical outlet or permanent unit installed by your
electrician. The national electrical code now requires
GFCI’s in the bathroom, garages, and outdoor outlets
for all NEW homes.
WHY DO YOU NEED A GFCI? Electricity and water
don’t mix. If your hair dryer falls in water while it’s
plugged in, the electric shock can kill you..
EVEN IF THE SWITCH IS “OFF”.
A regular fuse or circuit breaker won’t protect you
under these circumstances. A GFCI off ers you far
greater protection.
A GFCI CAN SAVE YOUR LIFE! COMPARED TO
THAT, THE PRICE IS SMALL! DON’T WAIT..
INSTALL ONE NOW!
*GFCI IS A SENSITIVE DEVICE WHICH REACTS
IMMEDIATELY TO A SMALL ELECTRIC CURRENT
LEAK BY STOPPING THE ELECTRICITY FLOW.
This message about..
Ground
Fault
Circuit
Interrupters
..can save a life!
13
2
Concentrator
Removable Air Filter
Ionic Light
Ergonomic Handle
Hanging Loop
overview
Nozzle
Cool Shot Button
Temperature Switch
Speed Switch
Power Cord
MC121_UserGuide.indd Spread 3 of 8 - Pages(14, 3)MC121_UserGuide.indd Spread 3 of 8 - Pages(14, 3) 8/6/15 8:56 AM8/6/15 8:56 AM
features
Cool Shot
To set your style, press the cool shot button and hold for
about 15 seconds after styling a portion of the hair. This
allows styles and curls to set in their position. Cool Shot is
available with any speed setting. Once Cool Shot is pressed,
the air will begin to cool. When curling your hair with a
round brush, use the cool shot for about 15 seconds
after drying to set the curl.
Temperature Switch
Haute Stuff Air has 3 available heat settings.
Hot: For thick hair or rough drying.
Warm: For medium hair and better control with styling.
Low: For fi ne hair and better control with styling.
Performance Speed Switch
Haute Stuff Air has 2 available speed settings.
High: Ideal for thicker or heavier hair to reduce drying time.
Low: Ideal for fi ner hair. Great for style control.
Off
Ionic Blast
The built-in ionic generator emits millions of pure negative
ions for smooth, shiny, frizz-free results. Negative ions close
the hair cuticle, keeping in moisture and adding body, ionic
dryers break down water molecules reducing drying time and
increasing effi ciency.
Cool Shot
Temp. Switch
Speed Switch
3
HOT
WARM
LOW
HIGH
LOW
OFF
servicing
Servicing
If you drop or damage your product it should not be used until it
has been examined by an authorized Service Center or appliance
technician.
For questions or comments, please contact us at (800) 327-7971
Blocked or clogged air intake vents will cause the dryer to
overheat.
If overheating occurs, an automatic safety devide will shut the
dryer or the heat off to prevent damage or personal injury. If the
unit or the heat cycles off , unplug the cord and allow the dryer to
cool for 10 to 15 minutes before restarting. Make sure the air vents
are clean.
12
MC121_UserGuide.indd Spread 4 of 8 - Pages(4, 13)MC121_UserGuide.indd Spread 4 of 8 - Pages(4, 13) 8/6/15 8:56 AM8/6/15 8:56 AM
ALCI safety
IMPORTANT
CHECK ALCI SAFETY FEATURE EVERY TIME YOU USE DRYER.
This dryer is equipped with an Appliance Leakage Circuit Interrupter (ALCI). This safe-
ty feature renders the tool inoperable under abnormal conditions, such as immersion in
water.
To make sure the ALCI is functioning properly and the exclusive water sensing system is
working, perform the following test:
1. Plug in dryer and press test button on plug.
2. Dryer will stop functioning. There will be an audible click and the reset button will pop
out.
3. To reset: ALCI with a reset button: Unplug unit.
Then push reset button in, then reinsert into outlet.
4. Be sure to repeat test every time you use this dryer
to confi rm the ALCI is operational.
5. If ALCI is not functioning properly, return the dryer
to Bersheart,LLC.
6. If a water immersion occurs, contact manufacturer immediately for examination and
repair.
Should the dryer go off and the Reset Button pop out during use, this could indicate a
malfunction in the dryer. Remove the plug from the outlet and allow the dryer to cool.
Reset the ALCI. Reinsert the plug into the outlet.
The dryer should function normally. If not, return to Quality Assurance for examination and
repair.
11
features
Professional Length Power Cord
Haute Stuff Air comes complete with a professional length
power cord with hang loop. It is important to inspect the cord
frequently for damage. If damaged, stop using immediately and
contact manufacturer for repair.
Concentrator Nozzle
Haute Stuff Air comes with 2 concentrator nozzles, that concentrate
the airfl ow onto a small focused area of the hair for quick, easy
smoothing.
When using a concentrator, it is highly recommended that one use a
round brush, paddle brush, or comb for even heat distribution.
Haute Stuff concentrators can be redirected, depending on the
comfort level. The ergonomic design combined with the concentrator
makes styling eff ortless.
Air Filter
Always make sure that the air fi lter is free of dust and lint as this
could cause the hair dryer to malfunction. To keep the air inlet free of
blockage, please follow the steps below.
1. Remove the intake cover by grasping it and turning
counter-clockwise.
2. Pull the cover away from the hair dryer.
3. Clean all deposits off the intake cover using a small brush or
damp cloth. If damp cloth is being used, make sure cover is
completely dry before placing on hair dryer.
4. Place the intake cover back onto the hair dryer and turn
clockwise to lock into place. 4
MC121_UserGuide.indd Spread 5 of 8 - Pages(12, 5)MC121_UserGuide.indd Spread 5 of 8 - Pages(12, 5) 8/6/15 8:56 AM8/6/15 8:56 AM
the perfect blow out
Gorgeous hair is the best revenge.
For a stunning salon quality blow out, begin with freshly washed hair,
then remove excess moisture by towel drying.
Apply your favorite Blow Out Spray for a smooth, shiny and
voluminous blow out.
Start at the top of the head, dividing your hair into 8 equal parts,
sectioned horizontally. Clip each section back, unclipping and working
on one section at a time.
At the nape, start at the root of the section and pull the hair
downward using a round bristle brush. Aim the dryer downward for a
smoother look, or upward at the root for more volume.
Do not blow-dry hair with your hair hanging upside-down. This
leads to unruly and tangled hair. Instead, blow dry with head tilted
sideways.
As you pull the brush through the hair, follow it closely with the dryer
to evenly distribute the heat. Make sure bristles are going through the
hair for extra luster.
Continue through the other sections until you reach the end of the
hair. I always recommend brushing the front sections away from the
face for a glamorous fi nished look.
5
safety instructions
FOR HOUSEHOLD USE ONLY
IMPORTANT SAFEGUARD
When using electrical appliances, especially when children are present, basic
safety precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING.
KEEP AWAY FROM WATER.
DANGER
As with most electrical tools, electrical parts are electrically live even
when switch is on the ‘OFF’ position.
WARNING - To reduce the risk of death by electric shock:
1. Always unplug it immediately after using.
2. Do not use while bathing.
3. Do not place or store appliance where it can fall or be pulled into a tub or
sink.
4. Do not place in or drop into water or other liquid.
5. If an appliance falls in water, unplug it immediately. Do not reach into
water.
6. Do not use if plug is loose in the outlet, as there may be risk of fi re, elec-
trical shock, electrical shortage and burning.
10
MC121_UserGuide.indd Spread 6 of 8 - Pages(6, 11)MC121_UserGuide.indd Spread 6 of 8 - Pages(6, 11) 8/6/15 8:56 AM8/6/15 8:56 AM
safety instructions
IMPORTANT SAFETY POINTS
Read these instructions thoroughly before using this
appliance or connecting to the power source supply.
Before switching on, make sure that the voltage of your
electricity supply is the same as that indicated on the rating
plate. Connecting it to any other power source may cause
damage.
This appliance has a polarized plug (one blade is wider than
the other) and as a safety feature, will only fi t into a polar-
ized outlet one way. Ensure the plug correctly fi ts into the
power outlet. If the plug does not fi t correctly into the outlet,
reverse the plug. Do not force the plug into the outlet. If it
still does not fi t, contact a qualifi ed electrician. Never modify
the plug in any way.
9
Properly store your dryer.
• Let the dryer cool down before storing.
• Ensure the product is completely dry, switched off and unplugged
from the power source before storage.
• Store in original box in a cool, dry place.
• Store in a safe place, away from children.
• Before you wrap around the cord, put the pin cover over the plug
pin fi rst.
Cleaning and Maintenance
1. Always turn off when not in use.
2. The dryer must be unplugged before cleaning.
3. Let the dryer cool down before cleaning.
4. Wipe the body of the dryer with a soft damp cloth.
5. To prolong the motor life, it is important to regularly remove dust
and dirt from the rear grille.
6. Do not use any harsh detergents, abrasives, solvents or cleaners.
7. Never immerse in water to clean.
8. Any other servicing should be performed by an authorized service
representative.
care
6
MC121_UserGuide.indd Spread 7 of 8 - Pages(10, 7)MC121_UserGuide.indd Spread 7 of 8 - Pages(10, 7) 8/6/15 8:56 AM8/6/15 8:56 AM
wigs & wishes
Wigs & Wishes® Powered by Friends Are By Your Side®
Every day, thousands of women and children are diagnosed with
cancer. Wigs & Wishes® Powered by Friends Are By Your Side® is a
non-profi t organization founded by Martino Cartier, that is dedicated
to providing wigs & granting wishes to these courageous individuals.
Supporting such a large initiative is made possible by a network
of participating salons, stylists and global corporate sponsorships.
Salons and stylists throughout the world empower women by
providing them with complimentary services that allow them for a brief
moment to forget about their fi ght.
Recent wishes and events include: Taylor Swift Meet & Greet for
Alex, Justin Bieber Meet & Greet front row for Kiki, A day on the set
with Adam Sandler for Angela, a family honeymoon for Jim Zetz, an
Annual Night of Wigs & Wishes and plenty more!
With every purchase of my product, 10% of net profi ts will be
donated directly to Friends Are By Your Side. Your support allows me
to continue to provide wigs & wishes to women and children battling
cancer.
For more information visit friendsarebyyourside.org
All my love,
7
troubleshooting
Troubleshooting
1. Before doing any inspection, please unplug the appliance.
2. Never allow the Power Cord to be pulled, twisted or severely bent.
Avoid wrapping the cord tightly around the hair dryer. Damage to
the power cord can cause it to rupture and short. Inspect the cord
frequently for damage. If damaged, stop using immediately and
contact manufacturer for repair.
3. Inspect switches, ensure that switches are engaged fully in the
correct position. In some cases, the switch is simply loose from
excessive use and not fully engaged.
4. Inspect the power outlet, If you are using a GFCI or GFI outlet with
a reset circuit breaker button on the panel, it may simply need to be
reset to start the current of electricity into your hair dryer. Try diff erent
outlets to rule out a potential faulty electrical outlet issue.
5. Inspect the cable, check the power cord for any cuts, cord
separation, or exposed wires. Before doing any power cord repair
to your fl at iron, ensure the device is completely powered off and
unplugged from any electrical outlet. In most cases, you can quickly
repair minor wire damage by securing the wires together and
wrapping the damaged area in electrical tape.
8
MC121_UserGuide.indd Spread 8 of 8 - Pages(8, 9)MC121_UserGuide.indd Spread 8 of 8 - Pages(8, 9) 8/6/15 8:56 AM8/6/15 8:56 AM
/
