Installation instructions
Side-by-Side combinations
20191106
7085218 - 01
SBS
Contents
1 General safety information................................... 2
2 External dimensions of the appliance................. 2
3 Side-by-side assembly.......................................... 2
The manufacturer works constantly on the further development
of all the types and models. Therefore please understand that
we have to reserve the right to make design, equipment and
technical modifications.
To get to know all the benefits of your new appliance, please
read the information contained in these instructions carefully.
The instructions apply to several models. Differences may
occur. Text relating only to specific appliances is marked with
an asterisk (*).
Instructions for action are marked with a
, the results of
action are marked with a .
1 General safety information
-
The socket must be easily accessible so that
the appliance can be quickly disconnected
from the supply in an emergency. It must be
outside the area of the rear of the appliance.
DANGER identifies a situation involving direct
danger which, if not obviated, may
result in death or severe bodily
injury.
WARNING identifies a dangerous situation
which, if not obviated, may result in
death or severe bodily injury.
CAUTION identifies a dangerous situation
which, if not obviated, may result in
minor or medium bodily injury.
NOTICE identifies a dangerous situation
which, if not obviated, may result in
damage to property.
Note identifies useful information and tips.
2 External dimensions of the
appliance
Appliance description Height A (mm)
SBSes 7155 1852
SBSes 7165 1852
SBS(esf) 7212 1852
SBS(esf) 7222 1852
SBS(es) 7252 1852
SBS(es/bs) 7253 1852
SBS 7262 1852
SBS(es/bs) 7263 1852
SBS(ef) 7343 1852
SBS(es/bs) 7353 1852
SBS(ef) 7242 1852
Fig. 1
3 Side-by-side assembly
All the assembly components are supplied with the appliance.
Fig. 2
Fig. 3
Ensure that the following tools are to hand:
q
Spirit level
q
Power screwdriver
q
Screwdriver Torx® 25
q
Open-ended spanner size 10 (included in supply package)
Information for moving the combined appliance:
q
Before assembling the appliances, site them as closely as
possible to the final position.
q
When moving the appliances, always take hold of them at
the outer front corners. On no account should you push with
your knee against the side walls or door.
q
The combined appliance is easiest to shift diagonally by
moving the left and right corner alternately.
General safety information
2 * Depending on model and options
Once the combined appliance is exactly in front of the aper-
ture, push it straight in.
q
If the combined appliance
has to be pulled out of the
aperture again, take hold of
it in the lower third area and
pull it straight forwards.
NOTICE
Risk of damage when moving the combined SBS appliance!
The combined SBS appliance is heavy once assembled. The
appliance may be dented by improper movement.
u
Observe the information given on moving the appliance (see
above).
u
Remove all protective film from the outside of the housing.
On the front of the appliance:
Fig. 4
u
If necessary, completely retract the height-adjustable feet
Fig. 4 (A)
at the front of both appliances so that they are not
touching the floor.
u
Place the caps
Fig. 4 (1)
onto the four front height-adjust-
able feet.
u
Push both appliances together up to approx. 10 mm apart so
that they stand flush at the front.
Fig. 5
u
Unclip and remove the covers
Fig. 5 (2)
.
The joining plate automatically aligns the height of the appli-
ances. If one appliance is slightly higher than the other, start
with that appliance.
u
Put the joining plate
Fig. 5 (3)
in place and fix it loosely to
one appliance with two screws
Fig. 5 (4)
.
u
Move the joining plate sideways so that the centre bar of the
plate lies on the side wall of the appliance. Tighten the
screws.
u
Now screw the joining plate to the other appliance. As you
do this, shift the appliances together or apart slightly as
necessary.
Fig. 6
u
If the appliance is fitted with the pre-mounted screw
Fig. 6 (7)
: Undo the screw.
The joining plate automatically aligns the depth of the appli-
ances. If one appliance is further forward than the other, start
with that appliance. Otherwise start with the appliance on the
left.
u
Fix the joining plate
Fig. 6 (5)
loosely to one appliance with
two screws
Fig. 6 (6)
.
u
Move the joining plate sideways so that the centre bar of the
plate lies on the side wall of the appliance. Tighten the
screws.
u
Now screw the joining plate to the other appliance. As you
do this, shift the appliances together or apart slightly as
necessary.
On the rear of the appliance:
Fig. 7
u
Insert the joining clamp
Fig. 7 (8)
at the top of the centre
side walls.
u
Insert the joining angle
Fig. 7 (9)
into the recess at the
bottom.
u
If the joining angle is too loose, fix it with a screw
Fig. 7 (10)
.
Note
u
To avoid vibration noise, ensure neither the clamps nor the
screws are in contact with the tubes on the rear of the appli-
ance!
On the front of the appliance:
Fig. 8
Side-by-side assembly
* Depending on model and options 3
NOTICE
Risk of damage to the castor bases!
u
When aligning the appliance by the back adjustable feet, do
not use a cordless screwdriver, as this will either damage the
height adjustment mechanism or possibly loosen the
adjusting rod. Adjust the feet by hand.
You can adjust the front height-adjustable feet with the open-
ended spanner
Fig. 8 (11)
included in the supply package, and
the rear height-adjustable feet* with a Torx® 25 screwdriver.
u
Retract the centre height-adjustable feet
Fig. 4 (C)
so they
are not in contact with the floor.
u
Level the combination using the outer height-adjustable feet
Fig. 4 (B)
.
Fig. 9
Before fitting the cover strip
Fig. 9 (12)
, press the two bars
together along the whole length. That makes it easier to insert
the strip into the gap. Use a soft cloth to press the strip into
place to avoid making dents in the surface. Carefully press the
strip into the gap, keeping it straight, to achieve an optimal joint.
u
On the front, press the long cover strip
Fig. 9 (12)
into the
vertical gap. Make sure the strip sits on top of the joining
plate
Fig. 9 (5)
.
u
Peel the protective film off the cover strip.*
Fig. 10
u
On the top of the appliances, press the short strip
Fig. 10 (13)
into the gap. Make sure the front edge of the
strip is flush with the joining plate
Fig. 10 (3)
.
u
Clip the cover
Fig. 10 (14)
over the gap between the two
control panel covers. Make sure the side edges of the cover
are flush with the control panel covers. To enable this, the
cover is expandable.
Fig. 11
u
Fit the bottom cover
Fig. 11 (15)
from above onto the joining
plate
Fig. 11 (5)
and snap it in at the bottom.
u
Connect the combination to the mains according to the
manual.
Appliances with IceMakers:
u
Connect the appliance to the fixed water connection
according to the manual.
NOTICE
Risk of damage when moving the combined SBS appliance!
The combined SBS appliance is heavy once assembled. The
appliance may be dented by improper movement.
u
Observe the information given on moving the appliance (see
above).
u
Carefully slide the combination into the intended position.
u
If necessary, align the height with the height-adjustable feet.
u
Lower the centre height-adjustable feet
Fig. 4 (C)
until they
touch the floor.
u
Then support the door: Extend the height-adjustable feet
Fig. 4 (A)
at the turn hinge until they are resting on the floor,
then turn them further by 90°.
Side-by-side assembly
4 * Depending on model and options
Side-by-side assembly
* Depending on model and options 5
Liebherr-Hausgeräte Marica EOOD
4202 Radinovo
Bezirk Plovdiv
Bulgarien
home.liebherr.com
-
1
-
2
-
3
-
4
-
5
-
6
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Liebherr SGNes 3010 Premium Assembly And Installation Instructions
-
-
-
Liebherr SGN 3063 Comfort Assembly And Installation Instructions
-
Liebherr SBSES8474 Owner's manual
-
Liebherr SBSes 8483 Premium Owner's manual
-
-
Liebherr SKESF 4240 User manual
-
-