Draw-Tite 75083 Installation guide

Draw-Tite
Brand
Draw-Tite
Model
75083
Category
Car kits
Type
Installation guide
Installation Instructions
Ford Explorer
Mazda Navajo
Mercury Mountaineer
Will not fit with 16
”
spare tire on 98 and later models
Part Numbers:
75083 70647
44067 33051
78166 UH
Will
not
fit
with
16
spare
tire
on
98
and
later
models
Hitch Shown In Proper Position
Equipment Required:
Do Not Exceed Lower of Towing Vehicle
Manufacturer’s Rati ng or
Hitch type
Max Gross
Trailer WT (LB)
Max Tongue
WT (LB)
Weight Distributing
6000 (2724 Kg) 600 (272 Kg)
Weight Carrying
Ball Mount
5000 (2270 Kg) 500 (227 Kg)
Bumper
Equipment
Required:
Wrenches: 13/16, 7/8, 15/16
Drill Bits: 1/2”
Fastener Kit: F75083
Wiring Access Location: SUV1, SUV2
Hole in frame
5
6
1
Slot in frame
each side
(see below)
2
7
8
Upright bar
1
Qty. (2) Carriage Bolt 1/2-13 X 1.75
5
Qty. (2) Bolt 9/16-12 X 2.00
2
Qty. (2)
Block
6
Qty. (2)
Block
3
4
Note: Fasteners typical both sides
1. Remove tow hooks, (if equipped) from vehicle frame and return to owner for reinstallation if hitch is removed from vehicle.
2. Raise receiver into position under vehicle, placing upright bars against outboard vertical surface of frame. Align hole in upright bar with
existing slot in frame, both sides.
3L litllft th hltif d ihtb h b
2
Qty.
(2)
Block
6
Qty.
(2)
Block
3
Qty. (2) Conical Washer 1/2
7
Qty. (2) Lock Washer 9/16
4
Qty. (2) Hex Nut 1/2-13
8
Qty. (2) Hex Nut 9/16-12
3
.
L
oose
l
y
i
ns
t
a
ll
f
as
t
eners
th
roug
h
s
l
o
t
i
n
f
rame an
d
upr
i
g
ht
b
ar as s
h
own a
b
ove.
94 and Prior Models:
4. Use hitch as template and drill 1/2" hole in bottom of vehicle frame, both sides as shown. Install remaining fasteners as shown.
95 and Later Models
:
4. Install remaining fasteners in hitch bracket and bottom of vehicle frame, both sides as shown.
Tighten all 1/2 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Tighten all 9/16 fasteners with torque wrench to 110 Lb.-Ft. (149 N*M)
z 2002, 2008, 2010, 2011 Cequent Performance Products
Sheet 1 of 1 N75083 4-11-11 Rev. B
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle
and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
Form: F205 Rev A 5-6-05
  • Page 1 1

Draw-Tite 75083 Installation guide

Draw-Tite
Brand
Draw-Tite
Model
75083
Category
Car kits
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents