Comfort Glow CSPBPT CSPINT User manual

Brand: Comfort Glow

Model: CSPBPT CSPINT

Category: Stoves

Type: User manual

This manual is also suitable for

WARNING: If the information in this manual is not

followed exactly, a fire or explosion may result caus-

ing property damage, personal injury, or loss of life.

-- Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other

appliance.

-- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

•

Do not touch any electrical switch; do not use

any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s in-

structions.

• If you cannot reach your gas supplier, call the fire

department.

-- Installation and service must be performed by a quali-

fied installer, service agency, or the gas supplier.

WARNING: Improper installation,

adjustment, alteration, service, or

maintenance can cause injury or

property damage. Refer to this

manual for correct installation and

operational procedures. For assis-

tance or additional information con-

sult a qualified installer, service

agency, or the gas supplier.

WARNING: This is an unvented gas-

fired heater. It uses air (oxygen)

from the room in which it is in-

stalled. Provisions for adequate

combustion and ventilation air must

be provided. Refer to

Air for Com-

bustion and Ventilation

section on

page 4 of this manual.

Propane/LP and Natural Gas

Thermostat Control Gas Log Heaters

(Burner System For Cast Iron Stoves)

Models

CSBNT, CSBPT

CSPBNT, CSPBPT

CSPINT, CSPIPT

This appliance may be installed in an aftermarket*, permanently located, manufactured (mobile)

home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appli-

ance is not convertible for use with other gases.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

(VENT-FREE)

GAS STOVE HEATER

OWNER’S OPERATION AND

INSTALLATION MANUAL

Save this manual for future reference.

For more information, visit www.desatech.com

111487-01C

For more information, visit www.desatech.com

SAFETY INFORMATION

IMPORTANT: Read this owner’s manual carefully and

completely before trying to assemble, operate, or ser-

vice this heater. Improper use of this heater can cause

serious injury or death from burns, fire, explosion,

electrical shock, and carbon monoxide poisoning.

Carbon Monoxide Poisoning: Early signs of carbon monoxide

poisoning resemble the flu, with headaches, dizziness, or nausea. If

you have these signs, the heater may not be working properly. Get

fresh air at once! Have heater serviced. Some people are more

affected by carbon monoxide than others. These include pregnant

women, people with heart or lung disease or anemia, those under the

influence of alcohol, and those at high altitudes.

Propane/LP Gas: Propane/LP gas is odorless. An odor-making

agent is added to the gas. The odor helps you detect a gas leak.

However, the odor added to the gas can fade. Gas may be present

even though no odor exists.

Make certain you read and understand all warnings. Keep this

manual for reference. It is your guide to safe and proper operation

of this heater.

WARNING ICON G 001

WARNINGS

DANGER: Carbon monoxide poisoning may lead

to death!

WARNING: Any change to this heater or its con-

trols can be dangerous.

WARNING: Do not allow fans to blow directly into

the stove. Avoid any drafts that alter burner flame

patterns. Ceiling fans can create drafts that alter

burner flame patterns. Altered burner patterns can

cause sooting.

WARNING: Do not use a blower insert, heat

exchanger insert or other accessory not approved for

use with this heater.

Due to high temperatures, the appliance should be

located out of traffic and away from furniture and

draperies.

Do not place clothing or other flammable material on

or near the appliance. Never place any objects on the

heater.

Stove becomes very hot when running heater. Keep

children and adults away from hot surface to avoid

burns or clothing ignition. Heater will remain hot for

a time after shutdown. Allow surface to cool before

touching.

Carefully supervise young children when they are in

the room with fireplace.

Keep the appliance area clear and free from combus-

tible materials, gasoline, and other flammable vapors

and liquids.

WARNING: This product contains and/or generates

chemicals known to the State of California to cause

cancer or birth defects, or other reproductive harm.

TABLE OF CONTENTS

SAFETY INFORMATION

TABLE OF CONTENTS

SAFETY INFORMATION ............................................................ 2

PRODUCT IDENTIFICATION ..................................................... 3

LOCAL CODES ........................................................................... 4

PRODUCT FEATURES .............................................................. 4

AIR FOR COMBUSTION AND VENTILATION ........................... 4

UNPACKING ............................................................................... 6

INSTALLATION ........................................................................... 6

OPERATING HEATER ............................................................... 11

INSPECTING BURNERS.......................................................... 12

CLEANING AND MAINTENANCE ............................................ 13

TROUBLESHOOTING .............................................................. 14

SPECIFICATIONS .................................................................... 17

REPLACEMENT PARTS .......................................................... 17

SERVICE HINTS ....................................................................... 17

TECHNICAL SERVICE ............................................................. 17

ACCESSORIES ........................................................................ 17

ILLUSTRATED PARTS BREAKDOWN AND PARTS LIST ....... 18

PARTS CENTRALS .................................................................. 22

OWNER’S REGISTRATION FORM .......................................... 23

WARRANTY INFORMATION ....................................... Back Page

111487-01C

For more information, visit www.desatech.com

1. This appliance is only for use with the type of gas indicated on

the rating plate. This appliance is not convertible for use with

other gases.

2. Do not place propane/LP supply tank(s) inside any structure.

Locate propane/LP supply tank(s) outdoors.

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not use any phone in

your building

• immediately call your gas supplier from a neighbor’s phone.

Follow the gas supplier’s instructions

• if you cannot reach your gas supplier, call the fire department

4. This heater shall not be installed in a bedroom or bathroom.

5. Do not place stove directly on carpeting, vinyl tile, or any

combustible material other than wood. The stove must set on

a metal or wood panel extending the full width and depth of

the appliance.

6. Do not use this stove as a wood burning fireplace. Use only

model 111485-02/111485-01 vent-free gas log heater.

7. Do not add extra logs or ornaments such as pine cones, vermicu-

lite, or rock wool. Using these added items can cause sooting.

8. This log heater is designed to be smokeless. If logs ever appear

to smoke, turn off heater and call a qualified service person.

Note:

During initial operation, slight smoking could occur due

to log curing and heater burning manufacturing residues.

9. To prevent the creation of soot, follow the instructions in Clean-

ing and Maintenance, page 13.

10. Before using furniture polish, wax, carpet cleaners, or similar

products, turn heater off. If heated, the vapors from these prod-

ucts may create a white powder residue within burner box or

on adjacent walls or furniture.

11. This heater needs fresh, outside air ventilation to run properly.

This heater has an Oxygen Depletion Sensing (ODS) safety shutoff

system. The ODS shuts down the heater if not enough fresh air is

available. See Air for Combustion and Ventilation, page 4. If heater

keeps shutting off, see Troubleshooting, page 14.

12. Do not run heater

• where flammable liquids or vapors are used or stored

• when under dusty conditions

13. Do not use this stove to cook food or burn paper or other objects.

14. Do not use heater if any part has been exposed to or under

water. Immediately call a qualified service technician to inspect

the room heater and to replace any part of the control system

and any gas control which has been under water.

15. Do not operate heater if any log is broken. Do not operate

heater if a log is chipped (dime-sized or larger).

16. Turn heater off and let cool before servicing. Only a qualified

service person should service and repair heater.

17. Operating heater above elevations of 4,500 feet could cause

pilot outage.

18. For propane/LP units, do not use propane/LP tank of less than

100 lb. capacity.

19. Provide adequate clearances around air openings.

20. Screen must be completely closed before using heater. Never

run heater with screen open.

SAFETY INFORMATION

Continued

PRODUCT IDENTIFICATION

Figure 1 - Typical Stove Cabinet Model with Comfort Glow Gas

Log Heater

Stove Body

Stove Door (Shown in

the open position)

Piezo Ignitor

Control Knob

One Piece Log

Set Inside Stove

Cavity

SAFETY INFORMATION

PRODUCT IDENTIFICATION

Screen

111487-01C

For more information, visit www.desatech.com

AIR FOR COMBUSTION AND

VENTILATION

Today’s homes are built more energy efficient than ever. New materi-

als, increased insulation, and new construction methods help reduce

heat loss in homes. Home owners weather strip and caulk around

windows and doors to keep the cold air out and the warm air in. During

heating months, home owners want their homes as airtight as possible.

While it is good to make your home energy efficient, your home

needs to breathe. Fresh air must enter your home. All fuel-burning

appliances need fresh air for proper combustion and ventilation.

Exhaust fans, fireplaces, clothes dryers, and fuel burning appliances

draw air from the house to operate. You must provide adequate fresh

air for these appliances. This will insure proper venting of vented

fuel-burning appliances.

PROVIDING ADEQUATE VENTILATION

The following are excerpts from National Fuel Gas Code,

ANSI Z223.1/NFPA 54, Section 5.3, Air for Combustion and

Ventilation.

All spaces in homes fall into one of the three following ventilation

classifications:

1. Unusually Tight Construction

2. Unconfined Space

3. Confined Space

The information on pages 4 through 6 will help you classify your

space and provide adequate ventilation.

Unusually Tight Construction

The air that leaks around doors and windows may provide enough

fresh air for combustion and ventilation. However, in buildings of

unusually tight construction, you must provide additional fresh air.

Unusually tight construction is defined as construction

where:

a. walls and ceilings exposed to the outside atmo-

sphere have a continuous water vapor retarder with

a rating of one perm (6 x 10-11 kg per pa-sec-m2) or

less with openings gasketed or sealed

and

b. weather stripping has been added on openable win-

dows and doors and

c. caulking or sealants are applied to areas such as

joints around window and door frames, between sole

plates and floors, between wall-ceiling joints, be-

tween wall panels, at penetrations for plumbing, elec-

trical, and gas lines, and at other openings.

If your home meets all of the three criteria above, you

must provide additional fresh air. See

Ventilation Air

From Outdoors

, page 6.

If your home does not meet all of the three criteria above,

proceed to

Determining Fresh-Air Flow For Heater Loca-

tion

, page 5.

Confined and Unconfined Space

The National Fuel Gas Code ANSI Z223.1/NFPA 54 defines a

confined space as a space whose volume is less than 50 cubic feet

per 1,000 Btu per hour (4.8 m

per kw) of the aggregate input rating

of all appliances installed in that space and an unconfined space as

a space whose volume is not less than 50 cubic feet per 1,000 Btu per

hour (4.8 m

per kw) of the aggregate input rating of all appliances

installed in that space. Rooms communicating directly with the

space in which the appliances are installed*, through openings not

furnished with doors, are considered a part of the unconfined space.

* Adjoining rooms are communicating only if there are doorless

passageways or ventilation grills between them.

WARNING: This heater shall not be installed in a

confined space or unusually tight construction unless

provisions are provided for adequate combustion and

ventilation air. Read the following instructions to in-

sure proper fresh air for this and other fuel-burning

appliances in your home.

LOCAL CODES

Install and use heater with care. Follow all local codes. In the absence

of local codes, use the latest edition of The National Fuel Gas Code

ANSI Z223.1/NFPA 54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

OPERATION

This heater is clean burning. It requires no outside venting. There is no

heat loss out a vent or up a chimney. Heat is generated by realistic,

dancing yellow flames. This heater is designed for vent-free operation.

State and local codes in some areas prohibit the use of vent-free heaters.

SAFETY PILOT

This heater has a pilot with an Oxygen Depletion Sensing (ODS) safety

shutoff system. The ODS/pilot is a required feature for vent-free room

heaters. The ODS/pilot shuts off the heater if there is not enough fresh air.

PIEZO IGNITION SYSTEM

This heater has a piezo ignitor. This system requires no matches,

batteries, or other sources to light heater.

PRODUCT FEATURES

LOCAL CODES

PRODUCT FEATURES

AIR FOR COMBUSTION AND VENTILATION

Providing Adequate Ventilation

111487-01C

For more information, visit www.desatech.com

AIR FOR COMBUSTION AND

VENTILATION

Continued

DETERMINING FRESH-AIR FLOW FOR

HEATER LOCATION

Determining if You Have a Confined or

Unconfined Space

Use this work sheet to determine if you have a confined or uncon-

fined space.

Space: Includes the room in which you will install heater plus any

adjoining rooms with doorless passageways or ventilation grills

between the rooms.

1. Determine the volume of the space (length x width x height).

Length x Width x Height = cu. ft. (volume of space)

Example:

Space size 20 ft. (length) x 16 ft. (width) x 8 ft. (ceiling

height) = 2560 cu. ft. (volume of space)

If additional ventilation to adjoining room is supplied with grills or open-

ings, add the volume of these rooms to the total volume of the space.

2. Multiply the space volume by 20 to determine the maximum Btu/Hr

the space can support.

(volume of space) x 20 = (maximum Btu/Hr the space can support)

Example: 2560 cu. ft. (volume of space) x 20 = 51,200 (maximum

Btu/Hr the space can support)

3. Add the Btu/Hr of all fuel burning appliances in the space.

Vent-free heater ______________ Btu/Hr

Gas water heater* ______________ Btu/Hr

Gas furnace ______________ Btu/Hr

Vented gas heater ______________ Btu/Hr

Gas fireplace logs ______________ Btu/Hr

Other gas appliances* + _____________ Btu/Hr

Total = _____________ Btu/Hr

* Do not include direct-vent gas appliances. Direct-vent draws com-

bustion air from the outdoors and vents to the outdoors.

Example:

Gas water heater _____________ Btu/Hr

Vent-free heater + _____________ Btu/Hr

Total = _____________ Btu/Hr

4. Compare the maximum Btu/Hr the space can support with the actual

amount of Btu/Hr used.

__________________ Btu/Hr (maximum the space can support)

__________________ Btu/Hr (actual amount of Btu/Hr used)

Example:

51,200 Btu/Hr (maximum the space can support)

70,000 Btu/Hr (actual amount of Btu/Hr used)

The space in the above example is a confined space because the actual Btu/

Hr used is more than the maximum Btu/Hr the space can support. You must

provide additional fresh air. Your options are as follows:

WARNING: If the area in which the heater may be

operated is smaller than that defined as an uncon-

fined space or if the building is of unusually tight

construction, provide adequate combustion and ven-

tilation air by one of the methods described in the

National Fuel Gas Code, ANSI Z223.1/NFPA 54, Sec-

tion 5.3

or applicable local codes.

40,000

30,000

70,000

A. Rework worksheet, adding the space of an adjoining room. If the

extra space provides an unconfined space, remove door to adjoining

room or add ventilation grills between rooms. See Ventilation Air

From Inside Building, page 6.

B. Vent room directly to the outdoors. See Ventilation Air From Out-

doors, page 6.

C. Install a lower Btu/Hr heater, if lower Btu/Hr size makes room unconfined.

If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support,

the space is an unconfined space. You will need no additional fresh air ventilation.

AIR FOR COMBUSTION AND VENTILATION

Determining Fresh-Air Flow for Heater Location

Ventilation Air

Figure 2 - Ventilation Air from Inside Building

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining unconfined space.

When ventilating to an adjoining unconfined space, you must

provide two permanent openings: one within 12" of the ceiling and

one within 12" of the floor on the wall connecting the two spaces

(see options 1 and 2, Figure 2). You can also remove door into

adjoining room (see option 3, Figure 2). Follow the National Fuel

Gas Code, ANSI Z223.1/NFPA 54, Section 5.3, Air for Combustion

and Ventilation for required size of ventilation grills or ducts.

Remove

Door into

Adjoining

Room,

Option

Ventilation Grills

Into Adjoining Room,

Option 2

Ventilation

Grills

Into Adjoining

Room,

Option 1

12"

111487-01C

For more information, visit www.desatech.com

NOTICE: This heater is intended for use as supple-

mental heat. Use this heater along with your primary

heating system. Do not install this heater as your

primary heat source. If you have a central heating

system, you may run system’s circulating blower

while using heater. This will help circulate the heat

throughout the house. In the event of a power outage,

you can use this heater as your primary heat source.

WARNING: A qualified service person must in-

stall heater. Follow all local codes.

WARNING: Never install the heater

• in a bedroom or bathroom

• in a recreational vehicle

• where curtains, furniture, clothing, or other flam-

mable objects are less than 42 inches from the

front, top, or sides of the heater

• in high traffic areas

• in windy or drafty areas

INSTALLATION

AIR FOR COMBUSTION AND

VENTILATION

Continued

Figure 3 - Ventilation Air from Outdoors

Outlet

Air

Ventilated

Attic

Outlet

Air

Inlet

Air

Inlet Air

Ventilated

Crawl Space

Crawl

Space

To Attic

AIR FOR COMBUSTION AND VENTILATION

Ventilation Air (Cont.)

UNPACKING

INSTALLATION

UNPACKING

1. Lift off corrugated box enclosing stove body crating.

2. Remove screws fastening back and top of wood frame enclo-

sure. Two or more people must carefully lift stove up and out

of wooden crate.

3. Remove plastic bag from stove body.

4. Remove back panel from stove (see Figure 4). Use an adjust-

able wrench or a 10 mm socket. Remove four (4) bolts and

washers. Keep bolts and washers to reattach back panel later.

5. Remove bubble-wrapped log set, rod and screen from stove.

Remove all protective packaging applied for shipment.

6. Check all items for any shipping damage. If damaged, promptly

inform dealer where you bought heater. Some fiber flakes may

fall from logs. This is acceptable.

7. Place freestanding stove near desired location in room.

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation grills or ducts. You must

provide two permanent openings: one within 12" of the ceiling and

one within 12" of the floor. Connect these items directly to the

outdoors or spaces open to the outdoors. These spaces include attics

and crawl spaces. Follow the National Fuel Gas Code, ANSI

Z223.1/NFPA 54, Section 5.3, Air for Combustion and Ventilation

for required size of ventilation grills or ducts.

IMPORTANT:

Do not provide openings for inlet or outlet air

into attic if attic has a thermostat-controlled power vent. Heated

air entering the attic will activate the power vent.

Figure 4 - Unpacking Stove from Wooden Shipping Enclosure

Back of Wood

Frame Enclosure

Back

Panel

Screws

Back

Panel

Screws

STOVE BACK

STOVE TOP

Top of

Wood

Frame

Enclosure

111487-01C

For more information, visit www.desatech.com

INSTALLATION

Check Gas Type

Clearances to Combustibles

CAUTION: This heater creates warm air currents.

These currents move heat to wall surfaces next to

heater. Installing heater next to vinyl or cloth wall

coverings or operating heater where impurities (such

as, but not limited to, tobacco smoke, aromatic

candles, cleaning fluids, oil or kerosene lamps, etc.)

in the air exist, may discolor walls or cause odors.

CHECK GAS TYPE

Use the correct gas type (natural or propane/LP) for your unit. If your

stove heater gas type is different from your house gas type, do not install

heater. Call dealer where you bought heater for proper type heater.

WARNING: This appliance is equipped for (natural

or propane/LP) gas. Field conversion is not permitted.

IMPORTANT:

Vent-free heaters add moisture to the air. Although

this is beneficial, installing heater in rooms without enough venti-

lation air may cause mildew to form from too much moisture. See

Air for Combustion and Ventilation, pages 4 through 6.

CLEARANCES TO COMBUSTIBLES

(Vent-Free Operation Only)

WARNING: Maintain the minimum clearances. If

you can, provide greater clearances from floor, ceil-

ing, and adjoining side and back walls.

Carefully follow the instructions below. This stove is a freestanding

unit designed to set directly on the floor. DO NOT place stove

directly on carpeting, vinyl tile or any combustible material other

than wood. The stove must be set on a metal or wood panel

extending the full width and depth of the stove for these floor

coverings.

IMPORTANT:

You must maintain minimum wall and

ceiling clearances during installation. The minimum clearances are

shown in Figure 5. Measure from outermost point of stove top.

Minimum Wall and Ceiling Clearances (see Figure 5)

A. Clearances from outermost point of stove top to any combus-

tible side wall should not be less than 12 inches.

B. Clearances from outermost point of stove top to any combus-

tible back wall should not be less than 6 inches (includes cor-

ner installations).

C. Clearances from the stove top to the ceiling should not be less

than 48 inches.

Figure 5 - Minimum Clearance to Walls and Ceiling (Stove May

Vary Depending on Model)

Front View

Top View

Side View

Front of

Stove Unit

12"

Minimum

12"

Minimum

48"

Minimum

Ceiling

Side Wall Side Wall

Back Wall

Side Wall Side Wall

Minimum

48"

Minimum

Ceiling

Floor

Back Wall

Corner

Wall

6 "

Minimum

Front of

Stove Unit

Front of

Stove Unit

INSTALLATION

Continued

111487-01C

For more information, visit www.desatech.com

CONNECTING TO GAS SUPPLY

WARNING: A qualified service person must con-

nect heater to gas supply. Follow all local codes.

Installation Items Needed

Before installing heater, make sure you have the items listed below.

• external regulator [propane/LP only] (supplied by installer)

• piping to stove location (check local codes)

• sealant (resistant to propane/LP gas)

• equipment shutoff valve *

• test gauge connection *

• sediment trap

• tee joint

• pipe wrench

* A CSA design-certified equipment shutoff valve with 1/8" NPT

tap is an acceptable alternative to test gauge connection. Purchase

the optional CSA design-certified equipment shutoff valve from

your dealer. See Accessories, page 17.

The gas inlet connection for the stove heater is located on the lower

right-hand side of the stove when viewed from the front of the unit.

The gas connection can be made either through the bottom right side

or through the lower back opening as illustrated in Figure 6. Make

sure gas log heater is secured to the stove cavity assembly.

For propane/LP units, the installer must supply an external regulator.

The external regulator will reduce incoming gas pressure. You must

reduce incoming gas pressure to between 11 and 14 inches of water.

If you do not reduce incoming gas pressure, heater regulator damage

could occur. Install external regulator with the vent pointing down as

shown in Figure 7. Pointing the vent down protects it from freezing

rain or sleet.

CAUTION: Never connect propane/LP heater di-

rectly to the propane/LP supply. This heater requires an

external regulator (not supplied). Install the external

regulator between the heater and propane/LP supply.

WARNING: This appliance requires a 1/2" NPT

(National Pipe Thread) inlet connection to the pres-

sure regulator.

INSTALLATION

Continued

Figure 6 - Gas Regulator Location and Gas Line Access Into

Stove Cabinet

Back

Stove

Panel

Front

Stove

Unit

Gas Inlet

Connection

Access

Product

Identification

Label

Gas Log Heater

Back ViewSide View

Figure 7 - External Regulator For Propane/LP Gas With Vent

Pointing Down

Propane/LP

Supply Tank

Vent Pointing

Down

CAUTION: For propane/LP units, use only new,

black iron or steel pipe. Internally-tinned copper tub-

ing may be used in certain areas. Check your local

codes. Use pipe of 1/2" diameter or greater to allow

proper gas volume to heater. If pipe is too small, undue

loss of volume will occur.

Installation must include an equipment shutoff valve, union, and

plugged 1/8" NPT tap. Locate NPT tap within reach for test gauge hook

up. NPT tap must be upstream from heater (see Figure 8, page 9).

IMPORTANT:

Install equipment shutoff valve in an accessible

location. The equipment shutoff valve is for turning on or shutting

off the gas to the appliance.

Check your building codes for any special requirements for locating

equipment shutoff valve to fireplaces.

Apply pipe joint sealant lightly to male NPT threads. This will

prevent excess sealant from going into pipe. Excess sealant in pipe

could result in clogged heater valves.

External Regulator

INSTALLATION

Connecting To Gas Supply

WARNING: Never connect natural gas heater to

private (non-utility) gas wells. This gas is commonly

known as wellhead gas.

111487-01C

For more information, visit www.desatech.com

INSTALLATION

Continued

WARNING: Use pipe joint sealant that is resistant

to liquid petroleum (LP) gas.

INSTALLATION

Connecting to Gas Supply (Cont.)

Checking Gas Connections

Tee Pipe Cap

Joint Nipple

Figure 8 - Gas Connection

3" Minimum

Sediment Trap

Gas

Regulator

(Propane/LP)

From External

Regulator (11"

W.C.** to 14"

W.C. Pressure)

CSA Design-Certified

Equipment Shutoff Valve

With 1/8" NPT Tap*

Approved Flexible

Gas Hose (if allowed

by local codes)

CAUTION: Avoid damage to regulator. Hold gas

regulator with wrench when connecting it to gas

piping and/or fittings.

We recommend that you install a sediment trap in supply line as

shown in Figure 8. Locate sediment trap where it is within reach for

cleaning. Install in piping system between fuel supply and heater.

Locate sediment trap where trapped matter is not likely to freeze. A

sediment trap traps moisture and contaminants. This keeps them

from going into heater controls. If sediment trap is not installed or

is installed wrong, heater may not run properly.

* Purchase the optional CSA design-certified equipment shutoff

valve from your dealer. See Accessories, page 17.

** Minimum inlet pressure for purpose of input adjustment.

WARNING: Never use an open flame to check for

a leak. Apply a noncorrosive leak detection fluid to all

joints. Bubbles forming show a leak. Correct all leaks

at once.

WARNING: Test all gas piping and connections,

internal and external to unit, for leaks after installing

or servicing. Correct all leaks at once.

CHECKING GAS CONNECTIONS

Pressure Testing Gas Supply Piping System

Test Pressures In Excess Of 1/2 PSIG (3.5 kPa)

1. Disconnect appliance with its appliance main gas valve (control

valve) and equipment shutoff valve from gas supply piping sys-

tem. Pressures in excess of 1/2 psig will damage heater regulator.

2. Cap open end of gas pipe where equipment shutoff valve was

connected.

3. Pressurize supply piping system by either opening propane/LP sup-

ply tank valve for propane/LP gas or opening main gas valve lo-

cated on or near gas meter for natural gas, or using compressed air.

4. Check all joints of gas supply piping system. Apply noncorrosive

leak detection fluid to gas joints. Bubbles forming show a leak.

5. Correct all leaks at once.

6. Reconnect heater and equipment shutoff valve to gas supply.

Check reconnected fittings for leaks.

Test Pressures Equal To or Less Than 1/2 PSIG (3.5 kPa)

1. Close equipment shutoff valve (see Figure 9).

2. Pressurize supply piping system by either opening propane/

LP supply tank valve for propane/LP gas or opening main gas

valve located on or near gas meter for natural gas, or using

compressed air.

3. Check all joints from gas meter for natural or propane/LP sup-

ply to equipment shutoff valve (see Figure 10 or 11, page 10).

Apply noncorrosive leak detection fluid to gas joints. Bubbles

forming show a leak.

4. Correct all leaks at once.

CAUTION: Make sure external regulator has been

installed between propane/LP supply and propane/LP

heater. See guidelines under Connecting to Gas Sup-

ply, page 8.

POSI

Figure 9 - Equipment Shutoff Valve

Closed

Equipment

Shutoff

Valve

Open

111487-01C

For more information, visit www.desatech.com

INSTALLATION

Continued

Figure 10 - Checking Gas Joints on Propane/LP Gas Unit

Control Valve Location

Propane/LP

Supply Tank

Equipment

Shutoff Valve

Pressure Testing Heater Gas Connections

1. Open equipment shutoff valve (see Figure 9, page 9).

2. Open main gas valve located on or near gas meter for natural

gas or open propane.LP supply tank valve.

3. Make sure control knob of heater is in the OFF position.

4. Check all joints from equipment shutoff valve to control valve

(see Figure 10 or 11). Apply noncorrosive leak detection fluid

to gas joints. Bubbles forming show a leak.

5. Correct all leaks at once.

6. Light heater (see Operating Heater, page 11). Check all other

internal joints for leaks.

7. Turn off heater (see To Turn Off Gas to Appliance, page 11).

INSTALLATION

Checking Gas Connections (Cont.)

Installing Rod and Screen

Figure 11 - Checking Gas Joints on Natural Gas Unit

Gas Meter

Equipment

Shutoff Valve

Control Valve Location

INSTALLING ROD AND SCREEN

1. Insert rod through small rings located at top of screen (see

Figure 12).

2. From back of stove, insert rod into hole located inside right

front of stove as shown in Figure 13.

3. Slip left side of rod down into slot on inside left front of stove

(see Figure 13).

Figure 12 - Assembling Rod and Screen

Slot on Inside Left

Front of Stove

Rod

Figure 13 - Installing Screen Into Stove (View From Back of

Stove)

Rings

Hole on Inside Right

Front of Stove

Rod with Screen

Assembled

111487-01C

For more information, visit www.desatech.com

OPERATING HEATER

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions

exactly, a fire or explosion may result causing prop-

erty damage, personal injury or loss of life.

A. This appliance has a pilot which must be lighted by hand.

When lighting the pilot, follow these instructions exactly.

B. BEFORE LIGHTING smell all around the appliance area

for gas. Be sure to smell next to the floor because some gas

is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do not use any phone in

your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire de-

partment.

C. Use only your hand to push in or turn the gas control knob.

Never use tools. If the knob will not push in or turn by

hand, don’t try to repair it, call a qualified service techni-

cian or gas supplier. Force or attempted repair may result

in a fire or explosion.

D. Do not use this appliance if any part has been under water.

Immediately call a qualified service technician to inspect the

appliance and to replace any part of the control system and

any gas control which has been under water.

1. STOP! Read the safety information, abovc.

2. Make sure equipment shutoff valve is fully open.

3. Turn control knob clockwise

Clockwise

to the OFF position.

4. Wait five (5) minutes to clear out any gas. Then smell for

gas, including near the floor. If you smell gas, STOP! Fol-

low “B” in the safety information, above. If you don’t smell

gas, go to the next step.

5. Turn control knob counterclockwise

C-clockwise

to the PI-

LOT position. Press in control knob for five (5) seconds

(see Figure 16, page 12).

LIGHTING

INSTRUCTIONS

NOTICE: During initial operation of new heater, burning

logs will give off a paper-burning smell. Orange flame

will also be present. Open a window to vent smell. This

will only last a few hours.

INSTALLATION

Installing Log Set

OPERATING HEATER

For Your Safety Read Before Lighting

Lighting Instructions

PILOT

Figure 14 - Installing One-Piece Stove Log Set

Burner Porting Areas (double

slotted rectangular openings

Figure 15 - Top View of One-Piece Log Set on Gas Log Heater

Safety Pilot

Location

One-Piece

Log Set

One-Piece

Log Set

Heater

Base

"U" Shaped

Cutout in

Chassis

Burner

Middle Section

at Bottom of

Log Set

INSTALLING LOG SET

1. Set one-piece log on heater base as shown in Figure 12. Make

sure middle section at bottom of log is seated into "U" shaped

cutout in center of heater base. Log will fit securely on base.

IMPORTANT:

Make sure log does not cover any burner ports

and does not touch the stove cavity (see Figure 14).

2. Fasten back panel to stove with four (4) bolts and washers re-

moved in step 4 of Unpacking, page 6. Make sure product iden-

tification label is located on the outside lower left-hand corner.

3. Place freestanding stove in desired position being careful not

to damage gas connections. Be sure to maintain clearances to

combustibles and wall clearances as outlined on page 7.

INSTALLATION

Continued

111487-01C

For more information, visit www.desatech.com

INSPECTING BURNERS

Check pilot flame pattern and burner flame patterns often.

PILOT FLAME PATTERN

Figure 18 shows a correct pilot flame pattern. Figure 19 shows an

incorrect pilot flame pattern. The incorrect pilot flame is not touching

the thermocouple. This will cause the thermocouple to cool. When the

thermocouple cools, the heater will shut down.

If pilot flame pattern is incorrect, as shown in Figure 19

• turn heater off (see To Turn Off Gas to Appliance, column 1)

• see Troubleshooting, pag 14

Note:

The pilot flame on natural gas units will have a slight curve,

but flame should be blue and have no yellow or orange color.

Figure 18 - Correct Pilot Flame

Pattern (Propane/LP Shown)

Figure 19 - Incorrect Pilot Flame

Pattern (Propane/LP Shown)

Thermocouple

Pilot Burner

Thermocouple

1. Follow steps 1 through 5 under Lighting Instructions, page 11.

2. Depress control knob and light pilot with match.

3. Keep control knob pressed in for 30 seconds after lighting

pilot. After 30 seconds, release control knob. Now follow

step 8 in Lighting Instructions, column 1.

THERMOSTAT CONTROL

OPERATION

The thermostat control knob can be set to any comfort level

between HI and LO. The thermostat will gradually modulate

the heat output and flame height from higher to lower settings,

or pilot, in order to maintain the comfort level you select. The

ideal comfort setting will vary by household depending upon the

amount of space to be heated, the output of the central heating

system, etc.

Note:

Selecting the HI setting with the control knob will cause the

burner to remain fully on, without modulating down in most cases.

MANUAL LIGHTING

PROCEDURE

OPERATING HEATER

Continued

OPERATING HEATER

Lighting Instructions (Cont.)

To Turn Off Gas To Appliance

Thermostat Control Operation

Manual Lighting Procedure

INSPECTING BURNERS

Figure 16 - Control Knob and Ignitor Button Location

Control Knob

Ignitor Button

Figure 17 - Pilot

Thermocouple

Pilot Burner

CAUTION: Do not try to adjust heating levels by

using the equipment shutoff valve.

TO TURN OFF GAS

TO APPLIANCE

Shutting Off Heater

Turn control knob clockwise

Clockwise

to the OFF position.

Shutting Off Burners Only (pilot stays lit)

Turn control knob clockwise

Clockwise

to the PILOT position.

Note:

You may be running this heater for the first time

after hooking up to gas supply. If so, the control knob may

need to be pressed in for 30 seconds or more. This will al-

low air to bleed from the gas system.

6. With control knob pressed in, press and release ignitor but-

ton. This will light pilot. The pilot is attached to the front

burner. If needed, keep pressing ignitor button until pilot lights.

Note:

If pilot does not stay lit, contact a qualified service

person or gas supplier for repairs. Until repairs are made,

light pilot with match. To light pilot with match, see Manual

Lighting Procedure, column 2.

7. Keep control knob pressed in for 30 seconds after lighting

pilot. After 30 seconds, release control knob.

• If control knob does not pop out when released, contact a

qualified service person or gas supplier for repairs.

Note:

If pilot goes out, repeat steps 3 through 7. This heater

has a safety interlock system. Wait one (1) minute for sys-

tem to reset before lighting pilot again.

8. Turn control knob counterclockwise

C-clockwise

to desired heat-

ing level. The burners should light. Set control knob to any

heat level between HI and LO.

111487-01C

For more information, visit www.desatech.com

CLEANING AND

MAINTENANCE

WARNING: Turn off heater and let cool before

cleaning.

CAUTION: You must keep control areas, burner,

and circulating air passageways of heater clean. In-

spect these areas of heater before each use. Have

heater inspected yearly by a qualified service person.

Heater may need more frequent cleaning due to exces-

sive lint from carpeting, pet hair, bedding material, etc.

BURNER INJECTOR HOLDER AND PILOT AIR

INLET HOLE

The primary air inlet holes allow the proper amount of air to mix with

the gas. This provides a clean burning flame. Keep these holes clear

of dust, dirt, lint and pet hair. Clean these air inlet holes prior to each

heating season. Blocked air holes will create soot. We recommend

that you clean the unit every three months during operation and have

heater inspected yearly by a qualified service person.

We also recommend that you keep the burner tube and pilot assembly

clean and free of dust and dirt. To clean these parts we recommend using

compressed air no greater than 30 PSI. Your local computer store,

hardware store, or home center may carry compressed air in a can. You

can use a vacuum cleaner in the blow position. If using compressed air in

a can, please follow the directions on the can. If you don't follow directions

on the can, you could damage the pilot assembly.

Note:

Removing the

rear panel and top grates of your stove will make cleaning easier.

1. Shut off the unit, including the pilot. Allow the unit to cool for

at least thirty minutes.

2. Inspect burner, pilot, and primary air inlet holes on injector

holder for dust and dirt (see Figure 20).

3. Blow air through the ports/slots and holes in the burner.

Figure 20 - Injector Holder On Outlet Burner Tube

Burner Tube

Injector Holder

(May Be Brass

or Aluminum

Depending on

Model)

Primary Air Inlet Holes

(Shape of Holes May

Vary by Model)

Figure 21 - Pilot Inlet Air Hole

Burner Tube

Pilot Assembly

Pilot Air

Inlet Hole

Ports/Slots

INSPECTING BURNERS

CLEANING AND MAINTENANCE

Cleaning Burner Injector Holder and Pilot Air Inlet Hole

Logs

4. Check the injector holder located at the end of the burner tube

again. Remove any large particles of dust, dirt, lint, or pet hair

with a soft cloth or vacuum cleaner nozzle.

5. Blow air into the primary air holes on the injector holder.

6. In case any large clumps of dust have now been pushed into

the burner repeat steps 3 and 4.

Clean the pilot assembly also. A yellow tip on the pilot flame

indicates dust and dirt in the pilot assembly. There is a small pilot

air inlet hole about two inches from where the pilot flame comes out

of the pilot assembly (see Figure 21). With the unit off, lightly blow

air through the air inlet hole. You may blow through a drinking straw

if compressed air is not available.

WARNING: Failure to keep the primary air

opening(s) of the burner(s) clear may result in soot-

ing and property damage.

LOGS

• If you remove logs for cleaning, refer to Installing Log Set, page

11, to properly replace logs.

• Replace log(s) if broken or chipped (dime-sized or larger).

MAIN BURNER

Periodically inspect all burner flame holes with the heater running. All

slotted burner flame holes should be open with yellow flame present.

All round burner flame holes should be open with a small blue flame

present. Some burner flame holes may become blocked by debris or

rust, with no flame present. If so, turn off heater and let cool. Remove

blockage. Blocked burner flame holes will create soot.

INSPECTING BURNERS

Continued

111487-01C

For more information, visit www.desatech.com

TROUBLESHOOTING

WARNING: Turn off heater

and let cool before servicing. Only

a qualified service person should

service and repair heater.

CAUTION: Never use a wire,

needle, or similar object to clean

ODS/pilot. This can damage ODS/

pilot unit.

POSSIBLE CAUSE

1. Ignitor electrode not connected to igni-

tor cable

2. Ignitor cable pinched or wet

3. Broken ignitor cable

4. Bad piezo ignitor

5. Ignitor electrode broken

6. Ignitor electrode positioned wrong

1. Gas supply turned off or equipment

shutoff valve closed

2. Control knob not in PILOT position

3. Control knob not pressed in while in

PILOT position

4. Air in gas lines when installed

5. ODS/pilot is clogged

6. Gas regulator setting is not correct

7. Depleted gas supply (propane/LP only)

1. Control knob not fully pressed in

2. Control knob not pressed in long enough

3. Equipment shutoff valve not fully open

4. Pilot flame not touching thermocouple,

which allows thermocouple to cool,

causing pilot flame to go out. This prob-

lem could be caused by one or both of

the following:

A) Low gas pressure

B) Dirty or partially clogged ODS/pilot

5. Thermocouple connection loose at con-

trol valve

6. Thermocouple damaged

7. Control valve damaged

REMEDY

1. Reconnect ignitor cable

2. Free ignitor cable if pinched by any

metal or tubing. Keep ignitor cable dry

3. Replace ignitor cable

4. Replace piezo ignitor

5. Replace pilot assembly

6. Replace pilot assembly

1. Turn on gas supply or open equipment

shutoff valve

2. Turn control knob to PILOT position

3. Press in control knob while in PILOT

position

4. Continue holding down control knob.

Repeat igniting operation until air is re-

moved

5. Clean ODS/pilot (see Cleaning and

Maintenance, page 13) or replace ODS/

pilot assembly

6. Replace gas control

7. Contact local propane/LP gas company

1. Press in control knob fully

2. After ODS/pilot lights, keep control

knob pressed in 30 seconds

3. Fully open equipment shutoff valve

4. A) Contact local natural or propane/LP

gas company

B) Clean ODS/pilot (see Cleaning and

Maintenance, page 13) or replace ODS/

pilot assembly

5. Hand tighten until snug, then tighten

1/4 turn more

6. Replace pilot assembly

7. Replace control valve

OBSERVED PROBLEM

When ignitor button is pressed, there is no

spark at ODS/pilot

When ignitor button is pressed, there is

spark at ODS/pilot but no ignition

ODS/pilot lights but flame goes out when

control knob is released

Note:

For additional help, visit DESA

Heating Products’ Technical Service web

site at www.desatech.com.

Note:

All troubleshooting items are listed in

order of operation.

TROUBLESHOOTING

111487-01C

For more information, visit www.desatech.com

OBSERVED PROBLEM

Burner does not light after ODS/pilot is lit

Delayed ignition burner

Burner backfiring during combustion

Slight smoke or odor during initial operation

Moisture/condensation noticed on windows

Heater produces a whistling noise when

burner is lit

Dark residue on logs or inside of fireplace

White powder residue forming within burner

box or on adjacent walls or furniture

REMEDY

1. Clean burner (see Cleaning and Main-

tenance, page 13) or replace burner

orifice

2. Contact local natural or propane/LP gas

company

1. Contact local natural or propane/LP gas

company

2. Clean burner (see Cleaning and Main-

tenance, page 13) or replace burner

orifice

1. Clean burner (see Cleaning and Mainte-

nance, page 13) or replace burner orifice

2. Replace damaged burner

3. Replace gas control

1. Check burner for dirt and debris. If

found, clean burner (see Cleaning and

Maintenance, page 13)

2. Replace gas control

3. Problem will stop after a few hours of

operation

1. Refer to Air for Combustion and Venti-

lation requirements (page 4)

1. Turn control knob to LO position and

let warm up for a minute

2. Operate burner until air is removed from

line. Have gas line checked by local

natural or propane/LP gas company

3. Observe minimum installation clear-

ances (see page 7)

4. Clean burner (see Cleaning and Main-

tenance, page 13) or replace burner

orifice

1. Properly locate logs (see Installing Log

Set, page 11)

2. Eliminate source of drafts around heater

3. Clean out air holes at burner inlet. Peri-

odically repeat as needed

4. Remove blockage

1. Turn heater off when using furniture

polish, wax, carpet cleaners, or similar

products

TROUBLESHOOTING

Continued

POSSIBLE CAUSE

1. Burner orifice clogged

2. Inlet gas pressure is too low

1. Manifold pressure is too low

2. Burner orifice clogged

1. Burner orifice is clogged or damaged

2. Damaged burner

3. Gas regulator defective

1. Not enough air

2. Gas regulator defective

3. Residues from manufacturing processes

and logs curing

1. Not enough combustion/ventilation air

1. Turning control knob to HI position

when burner is cold

2. Air in gas line

3. Air passageways on heater blocked

4. Dirty or partially clogged burner orifice

1. Improper log placement

2. Drafts or other air currents affecting

flame pattern

3. Air holes at burner inlet blocked

4. Burner flame holes blocked

1. When heated, vapors from furniture pol-

ish, wax, carpet cleaners, etc. may turn

into white powder residue

TROUBLESHOOTING

111487-01C

For more information, visit www.desatech.com

WARNING: If you smell gas

• Shut off gas supply.

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in

your building.

• Immediately call your gas supplier from a neighbor’s phone.

Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

POSSIBLE CAUSE

1. Metal expanding while heating or con-

tracting while cooling

1. Heater burning vapors from paint, hair

spray, glues, cleaners, chemicals, new

carpet, etc. (See

IMPORTANT

state-

ment above)

2. Gas leak. See Warning statement at

top of page

1. Not enough fresh air is available

2. Low line pressure

3. ODS/pilot is partially clogged

1. Gas leak. See Warning statement at

top of page

2. Control valve defective

1. Foreign matter between control valve

and burner

2. Gas leak. See Warning statement at

top of page

OBSERVED PROBLEM

Heater produces a clicking/ticking noise

just after burner is lit or shut off

Heater produces unwanted odors

Heater shuts off in use (ODS operates)

Gas odor even when control knob is in OFF

position

Gas odor during combustion

REMEDY

1. This is common with most heaters. If

noise is excessive, contact qualified ser-

vice person

1. Open window and ventilate room. Stop

using odor causing products while heater

is running

2. Locate and correct all leaks (see Check-

ing Gas Connections, page 9)

1. Open window and/or door for ventilation

2. Contact local natural or propane/LP gas

company

3. Clean ODS/pilot (see Cleaning and

Maintenance, page 13)

1. Locate and correct all leaks (see Check-

ing Gas Connections, page 9)

2. Replace control valve

1. Take apart gas tubing and remove for-

eign matter

2. Locate and correct all leaks (see Check-

ing Gas Connections, page 9)

IMPORTANT:

Operating heater where impurities in air exist may create odors.

Cleaning supplies, paint, paint remover, cigarette smoke, cements and glues, new

carpet or textiles, etc., create fumes. These fumes may mix with combustion air

and create odors. These odors will disappear over time.

TROUBLESHOOTING

Continued

TROUBLESHOOTING

111487-01C

For more information, visit www.desatech.com

SERVICE HINTS

When Gas Pressure Is Too Low

• pilot will not stay lit

• burners will have delayed ignition

• heater will not produce specified heat

• propane/LP gas supply may be low

You may feel your gas pressure is too low. If so, contact your local

propane/LP gas supplier.

TECHNICAL SERVICE

You may have further questions about installation, operation, or

troubleshooting. If so, contact DESA Heating Products’ Technical

Service Department at 1-866-672-6040. When calling, please have

your model and serial numbers of your heater ready.

You can also visit DESA Heating Products’ technical service web

site at www.desatech.com.

ACCESSORIES

Purchase these heater accessories from your local dealer. If they

can not supply these accessories, call DESA Heating Products at

1-866-672-6040 for referral information. You can also write to the

address listed on the back page of this manual.

SPECIFICATIONS

REPLACEMENT PARTS

SERVICE HINTS

TECHNICAL SERVICE

ACCESSORIES

REPLACEMENT PARTS

Note:

Use only original replacement parts. This will protect your

warranty coverage for parts replaced under warranty.

PARTS UNDER WARRANTY

Contact authorized dealers of this product. If they can’t supply

original replacement part(s), call DESA Heating Products’ Techni-

cal Service Department at 1-866-672-6040.

When calling DESA Heating Products, have ready

• your name

• your address

• model and serial numbers of your heater

• how heater was malfunctioning

• type of gas used (propane/LP or natural gas)

• purchase date

Usually, we will ask you to return the part to the factory.

PARTS NOT UNDER WARRANTY

Contact authorized dealers of this product. If they can’t supply original

replacement part(s), either contact your nearest Parts Central (see page 22)

or call DESA Heating Products at 1-866-672-6040 for referral information.

When calling DESA Heating Products, have ready

• model number of your heater

• the replacement part number

SPECIFICATIONS

CSBPT, CSPBPT, CSPIPT

(Includes 111485-01 Burner Chassis)

Btu (Variable) 16,000/30,000

Type Gas Propane/LP Only

Ignition Piezo

Pressure Manifold 8" W.C.

Inlet Gas Pressure (in. of water)

Maximum 14"

Minimum* 11"

Shipping Weight 265 lbs.

* For input adjustment

CSBNT, CSPBNT, CSPINT

(Includes 111485-02 Burner Chassis)

Btu (Variable) 16,000/30,000

Type Gas Natural Gas Only

Ignition Piezo

Pressure Manifold 3.5" W.C.

Inlet Gas Pressure (in. of water)

Maximum 10.5"

Minimum* 5"

Shipping Weight 265 lbs.

* For input adjustment

EQUIPMENT SHUTOFF VALVE - GA5010

For all models. Equipment shutoff valve with 1/8" NPT tap. Fits 1/2"

NPT pipe.

CLEANING KIT - CCK

(Not Shown)

For all models. Your vent-free gas appliance requires regular

cleaning and maintenance to prevent performance problems. This

kit gives you the tools and instructions to make it easy to clean all

critical areas of your appliance.

INFORMATION VIDEO - 108917-01

For all models. A care and maintenance video is available by calling

1-866-672-6040. You may also email your request to

[email protected].

111487-01C

For more information, visit www.desatech.com

ILLUSTRATED PARTS

BREAKDOWN

MODELS

111485-01 AND 111485-02

ILLUSTRATED PARTS BREAKDOWN

Models 111485-01 and 111485-02

111487-01C

For more information, visit www.desatech.com

PARTS LIST

This list contains replaceable parts used in your stove. For replace-

ment parts see Replacement Parts on page 17 of this manual.

PARTS LIST

Models 111485-01 and 111485-02

KEY PART NUMBER

NO. 111485-01 111485-02 DESCRIPTION QTY.

1 104026-01 104026-01 Stove Log 1

2 098249-01 098249-01 Nut, M5 2

3 ** ** Painted Base Assembly 1

4 104454-01 104454-01 Bracket, Regulator 1

5 098867-10 098867-14 Gas Regulator 1

6 104425-01 104425-01 Inlet Tube 1

7 104424-03 104424-03 Outlet Burner Tube 1

8 099056-19 099056-26 Burner Orifice Injector 1

9 111124-01 111124-01 Burner Retainer Spring 1

10 102980-01 102980-01 Burner 1

11 101329-22 101329-21 Control Valve 1

12 104472-01 104472-01 Bracket 1

13 099211-01 099211-01 Screw 2

14 102445-01 102445-01 Piezo Ignitor 1

15 099387-09 099387-09 Pilot Tube 1

16 098271-10 098271-10 Ignitor Cable 1

17 104286-01 104285-01 ODS Pilot 1

18 M11084-38 M11084-38 Screw, Hex Head (#8-18 x .38) 7

PARTS AVAILABLE — NOT SHOWN

100563-01 100563-01 Warning Plate 1

101054-01 101054-01 Lighting Instructions Plate 1

100565-01 100565-01 Warning Plate Fastener 1

101137-04 101137-04 Hardware Kit 1

** Not a field replaceable part.

111487-01C

For more information, visit www.desatech.com

ILLUSTRATED PARTS

BREAKDOWN

STOVE BODY MODELS

CSB SERIES, CSPB SERIES,

AND CSPI SERIES

ILLUSTRATED PARTS BREAKDOWN

Models CSB Series, CSPB Series, and CSPI Series

Page is loading ...

Comfort Glow CSPBPT CSPINT User manual

Brand: Comfort Glow

Model: CSPBPT CSPINT

Category: Stoves

Type: User manual

This manual is also suitable for

Download PDF

report

Comfort Glow CSPBPT CSPINT User manual

This manual is also suitable for

Comfort Glow CSPBPT CSPINT User manual

Related papers

Other documents