V3 ENGLISH 14-1412
1 Connect HDMI cables from each of your source devices (such as a cable box or Blu-ray
player) to any of the IN ports on your HDMI Switch.
2 Connect an HDMI cable from your display (such as a TV) to the OUT port on your HDMI
Switch.
3 Connect the AC power adapter to the POWER connector on your HDMI Switch, then
connect the other end to an AC power outlet.
Using your HDMI Switch
1 Turn on your display (such as a TV) and make sure it is set to the HDMI input connected to
the HDMI Switch.
2 Turn on the source device (such as a Blu-ray player) that you want to use. The HDMI Switch
should automatically change to that input input. The corresponding LED lights.
OR
If the HDMI Switch does not automatically change to the correct input, press SELECT on
your HDMI Switch until the corresponding LED lights.
Note: To switch to another source, turn o the source you are currently using, then turn the
new source on.
OR
Press SELECT on your HDMI Switch until the corresponding LED lights.
Troubleshooting
Specications
Legal notices
• The manufacturer reserves the right to make changes in the hardware, packaging, and any
accompanying documentation without prior written notice.
• HDMI, the HDMI Logo, and High-Denition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC.
• DX-HZ325 incorporates HDMI® technology.
• Trademarks and brand names are the properties of their respective owners.
FCC Information
Changes or modications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
ICES-003 statement:
CAN ICES-3 (B)/NMB-3 (B)
One-year limited warranty
Visit www.dynexproducts.com for details.
Contact Dynex:
For customer service, call 1-800-305-2204 (U.S. and Canada) or 01-800-926-3020 (Mexico)
www.dynexproducts.com
DYNEX is a trademark of Best Buy and its aliated companies. Registered in some countries.
Distributed by Best Buy Purchasing, LLC, 7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2015 Best Buy. All rights reserved. Made in China
Video resolution
Dimensions
Shipping weight
480i to 1080p from source device
2.8 × 2.9 × 1 in. (147 × 73.5 × 26 mm)
.82 lb. (.372 kg)
Problem
No video
and/or
audio.
Solution
• Make sure that all connections are correct and secure.
• Make sure that the HDMI Switch is connected to power.
• Make sure that your display is set to the source (input) that the HDMI
Switch is connected to.
• Make sure that your HDMI cables are not damaged. Try replacing your cables.
• Unplug the power cable, wait 30 seconds, then plug it back in.
• Make sure that your DVD or Blu-ray disc is an original. HDMI includes HDCP
copy protection, which prevents playback of illegally copied movies.