Comnet CNGE24FX12TX12MS Series User manual

INSTALLATION AND OPERATION MANUAL

CNGE24FX12TX12MS[POE]

Industrial Grade Managed Ethernet Switch w/

12 × 100/1000Base-FX + 12 × 10/100/1000Base-TX Ports

w/ Optional 30W PoE

The ComNet CNGE24FX12TX12MS[POE] has twelve 100/1000Base-FX SFP* ports

and twelve 10/100/1000Base-TX ports. All SFP ports utilize ComNet SFP modules

for fiber and connector type and distance. The IEEE802.3-compliant unit offers

multiple Ethernet redundancy protocols (MSTP/RSTP/STP/ERPS (G.8032)) which

protect your applications from network interruptions or temporary malfunctions by

redirecting transmission within the network. The switch provides advanced IP-based

management that can limit the maximum bandwidth for each connected IP device,

allowing the user to adjust usage. Application-based QoS can set a higher priority

for data streaming. The Device-Binding function can prevent unauthorized network

access, increasing security.

The CNGE24FX12TX12MSPOE models provide twelve electrical ports supporting up to

thirty watts of power. All PoE ports are IEEE 802.3at compliant.

Each model is provided with redundant power inputs which can be either one mains

voltage and one or two low voltage DC inputs or two low voltage DC inputs.

Rev. 2.22.18

This guide serves the following

ComNet Model Numbers:

CNGE24FX12TX12MS

CNGE24FX12TX12MSPOE

INS_CNGE24FX12TX12MS[POE] Rev. 2.22.18 PAGE 2

INSTRUCTION MANUAL CNGE24FX12TX12MS[POE]

TECH SUPPORT: 1.888.678.9427

Contents

Regulatory Compliance Statement 6

Warranty 6

Disclaimer 6

Safety Information 7

Hardware Installation 8

Rack mount kit assembly 8

Hardware Overview 9

Power Supply 10

Front Panel LEDs 10

WEB Management 11

Login 11

Configuration 15

Green Ethernet 23

Thermal Protection 25

DHCP 28

DHCP Pool Configuration 31

Security 36

Network 54

Screen 57

Aggregation 84

Loop Protection 86

Spanning Tree 87

IPMC Profile 94

MVR 97

IPMC 99

LLDP 107

PoE 109

EPS 111

Ethernet Protection Switch Configuration 112

Ethernet Ring Protection Switch Configuration 129

MAC Table 132

INS_CNGE24FX12TX12MS[POE] Rev. 2.22.18 PAGE 3

INSTRUCTION MANUAL CNGE24FX12TX12MS[POE]

TECH SUPPORT: 1.888.678.9427

VLAN Translation 133

VLANs 135

Private VLANs 138

VCL 140

Protocol-based VLAN 141

Voice VLAN 145

Mirroring & Remote Mirroring Configuration 166

UPnP 169

GVRP 170

Monitor Menu 172

System 172

CUP Load 173

System IP Status 174

System Log 175

Port State 177

Green Ethernet 178

Thermal Protection 179

Por ts 179

QoS Statistics 180

DHCP 184

Security 190

AAA 198

Aggregation Status 204

LACP 205

Loop Protection 207

MVR 212

IPMC 215

LLDP 221

PoE 226

MAC Table 227

VLANs 228

Diagnostics Menu 231

Ping 231

Ping6 232

PHYtest 233

INS_CNGE24FX12TX12MS[POE] Rev. 2.22.18 PAGE 4

INSTRUCTION MANUAL CNGE24FX12TX12MS[POE]

TECH SUPPORT: 1.888.678.9427

Maintenance Menu 234

Restart Device 234

Factory Defaults 234

Software 235

Configuration 237

Using Switch CLI 240

About CLI Management 240

CLI Management by RS-232 Serial Console 240

CLI Management by Telnet 243

Commander Groups 244

Quick Start 245

Log In and Reset Configuration to Factory Default 245

Set Device Hostname and Admin User Password 246

Set VLAN 1 IP Address 246

Display and Save Configuration to Flash 248

ICLI Basics 250

Command Structure and Syntax 251

Syntax 252

Ethernet Interface Naming 254

Using the Keyboard 256

Basic Line Editing 256

Command History 257

Context-Sensitive Help 259

Using Context-Sensitive Help 259

Long Lines and Pagination 261

Other Special Keys 262

Filtering Output 262

Understanding Modes and Sub-Modes 263

Using ‘do’ While in a Sub-Mode 266

Changing Between ICLI Modes 267

Understanding Privilege Levels 268

Configuring Privilege Level Passwords 269

Understanding Terminal Parameters 270

Changing Terminal Parameters 271

INS_CNGE24FX12TX12MS[POE] Rev. 2.22.18 PAGE 5

INSTRUCTION MANUAL CNGE24FX12TX12MS[POE]

TECH SUPPORT: 1.888.678.9427

Using Banners 273

Configuring Banners 273

Configuring the System 275

Configuration Example 275

Resetting or Removing Condiguration with “no” 277

Using “no” Forms 277

Managing Users 278

Adding, Modifying, and Deletion Users 278

Using Show Commands 279

Listing All Show Commands 280

Show running-config 283

Default vs. Non-default vs. All Defaults 283

Show running-config [all-defaults] 285

Show running-config feature feature_name [all-defaults] 285

Show running-config interface list [all-defaults] 286

Working with Configuration Files 287

Reverting to Default Configuration 288

Working with Configuration Files 289

Using Reload Commands 291

Working with Software Images 292

Appendix A 293

Ethernet Ring Protection Switching Example Configuration 293

Configuring ERPS from the Web GUI 294

Ethernet Ring Protection Switching Configuration 301

Configuring ERPS from the ICLI 306

INS_CNGE24FX12TX12MS[POE] Rev. 2.22.18 PAGE 6

INSTRUCTION MANUAL CNGE24FX12TX12MS[POE]

TECH SUPPORT: 1.888.678.9427

Regulatory Compliance Statement

Product(s) associated with this publication complies/comply with all applicable regulations. Please

refer to the Technical Specifications section for more details.

Warranty

ComNet warrants that all ComNet products are free from defects in material and workmanship

for a specified warranty period from the invoice date for the life of the installation. ComNet will

repair or replace products found by ComNet to be defective within this warranty period, with

shipment expenses apportioned by ComNet and the distributor. This warranty does not cover

product modifications or repairs done by persons other than ComNet-approved personnel, and

this warranty does not apply to ComNet products that are misused, abused, improperly installed,

or damaged by accidents.

Please refer to the Technical Specifications section for the actual warranty period(s) of the

product(s) associated with this publication.

Disclaimer

Information in this publication is intended to be accurate. ComNet shall not be responsible for its

use or infringements on third-parties as a result of its use. There may occasionally be unintentional

errors on this publication. ComNet reserves the right to revise the contents of this publication

without notice.

INS_CNGE24FX12TX12MS[POE] Rev. 2.22.18 PAGE 7

INSTRUCTION MANUAL CNGE24FX12TX12MS[POE]

TECH SUPPORT: 1.888.678.9427

Safety Information

» Only ComNet service personnel can service the equipment. Please contact ComNet Technical

Support.

» The equipment should be installed in locations with controlled access, or other means of

security, and controlled by persons of authority. When operating at temperatures above 51º C, the

equipment surfaces will be hot to the touch. Installation in restricted access location is required

for this case.

» For POE models requiring a power supply not labeled LPS, the unit should be installed in a

restricted access location using a 60950-1, 2nd Edition + Am. 1 + Am. 2 Certified power supply

rated for the ambient temperature in which it is installed. Total derated power rating should be

greater than the sum of the attached loads plus 30 W for the switch.

» Use CDRH compliant SFP modules when using fiber connectivity with this device.

» When used in Australia or New Zealand, the product is certified for intra building applications

only, and should not be directly connected to network cables with outside plant routing.

INS_CNGE24FX12TX12MS[POE] Rev. 2.22.18 PAGE 8

INSTRUCTION MANUAL CNGE24FX12TX12MS[POE]

TECH SUPPORT: 1.888.678.9427

Hardware Installation

Rack mount kit assembly

You can find the rack mount kit and the screws in the packing box. Please assembly the rack

mount kit on the switch with screws as shown below:

INS_CNGE24FX12TX12MS[POE] Rev. 2.22.18 PAGE 9

INSTRUCTION MANUAL CNGE24FX12TX12MS[POE]

TECH SUPPORT: 1.888.678.9427

Hardware Overview

1 2 3 4

CNGE24FX12TX12MS[POE] Front Panel

Call-out Description

1

Status LED

2

12 × 10/100/1000Base-TX RJ45 Ports

3

12 × 100/1000Base-FX SFP Ports

4

USB Console Port

123 4

CNGE24FX12TX12MS[POE] Rear Panel

Call-out Description

1

1 × Mains Power Switch

2

1 × 90-240 VAC Mains Power Input

3

2 × 6-14 VDC or 48-57 VDC (model dependent) Redundant Power Input 2-Pin Terminal Block Connector

4

Fault Relay 2-Pin Terminal Block Connector

INS_CNGE24FX12TX12MS[POE] Rev. 2.22.18 PAGE 10

INSTRUCTION MANUAL CNGE24FX12TX12MS[POE]

TECH SUPPORT: 1.888.678.9427

Power Supply

For CNGE24FX12TX12MS Models, Power Supply must be 6 to 14 VDC @ 30 W max or 90-240 VAC

mains.

For CNGE24FX12TX12MSPOE Model, Power Supply must be 48 to 57 VDC @ 390 W max or

90-240 VAC mains.

IMPORTANT SAFEGUARDS:

A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating

ambient temperature of the rack environment may be greater than room ambient. Therefore,

consideration should be given to installing the equipment in an environment compatible with

the maximum ambient temperature (T

ma

) specified by the manufacturer.

B) Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air

flow required for safe operation of the equipment is not compromised.

Front Panel LEDs

LED Color Status Description

Status Green On Switch is operational

Gigabit Ethernet ports

Link Amber On Port in Full Duplex mode

Activity Green Blinking Data transmitted

Gigabit SFP ports

Link/Activity Green Blinking Data transmitted

INS_CNGE24FX12TX12MS[POE] Rev. 2.22.18 PAGE 11

INSTRUCTION MANUAL CNGE24FX12TX12MS[POE]

TECH SUPPORT: 1.888.678.9427

WEB Management

Login

Open a web browser and navigate to the switch using http:// and the IP address of the switch.

The default IP address is 192.168.10.1

This is the main login page. Default user name is “admin” with maximum length 32 Default

password is “admin” with maximum length 32.

Warning – Any changes made to the settings will apply only to the current running configuration

of the switch and will be lost in the event of a power cycle.

To save any changes made to persistent memory please go to "Maintenance ¦

Configuration ¦ Save startup-config" to write the changes to the switches startup

configuration.

INS_CNGE24FX12TX12MS[POE] Rev. 2.22.18 PAGE 12

INSTRUCTION MANUAL CNGE24FX12TX12MS[POE]

TECH SUPPORT: 1.888.678.9427

Menu Trees

The following tree views show the available menus within the switch web GUI. It offers the user

quick access to all the configuration settings within the switch.

Configuration Menu

INS_CNGE24FX12TX12MS[POE] Rev. 2.22.18 PAGE 13

INSTRUCTION MANUAL CNGE24FX12TX12MS[POE]

TECH SUPPORT: 1.888.678.9427

Monitor Menu

Diagnostics Menu

INS_CNGE24FX12TX12MS[POE] Rev. 2.22.18 PAGE 14

INSTRUCTION MANUAL CNGE24FX12TX12MS[POE]

TECH SUPPORT: 1.888.678.9427

Maintenance Menu

INS_CNGE24FX12TX12MS[POE] Rev. 2.22.18 PAGE 15

INSTRUCTION MANUAL CNGE24FX12TX12MS[POE]

TECH SUPPORT: 1.888.678.9427

Configuration

System Information

The switch system information is provided here.

Object Description

System Contact The textual identification of the contact person for this managed node, together with

information on how to contact this person. The allowed string length is 0 to 255, and the allowed

content is the ASCII characters from 32 to 126.

System Name An administratively assigned name for this managed node. By convention, this is the node’s fully-

qualified domain name. A domain name is a text string drawn from the alphabet (A-Za-z), digits

(0-9), minus sign (-). No space characters are permitted as part of a name. The first character

must be an alpha character. And the first or last character must not be a minus sign. The allowed

string length is 0 to 255.

System Location The physical location of this node (e.g., telephone closet, 3rd floor). The allowed string length is

0 to 255, and the allowed content is the ASCII characters from 32 to 126.

Apply Click to apply changes without saving. *

Reset Click to revert to previous values.

Save to startup-config is under Maintenance Menu tree.

INS_CNGE24FX12TX12MS[POE] Rev. 2.22.18 PAGE 16

INSTRUCTION MANUAL CNGE24FX12TX12MS[POE]

TECH SUPPORT: 1.888.678.9427

System IP

Configure IP basic settings, control IP interfaces and IP routes. The maximum number of interfaces

supported is 8 and the maximum number of routes is 32.

Object Description

IP Configuration

Mode Configure whether the IP stack should act as a Host or a Router. In Host mode, IP traffic

between interfaces will not be routed. In Router mode traffic is routed between all

interfaces.

DNS Server This setting controls the DNS name resolution done by the switch. The following modes are

supported:

• From any DHCP interfaces

The first DNS server offered from a DHCP lease to a DHCP-enabled interface will be used.

• No DNS server

No DNS server will be used.

• Configured

Explicitly provide the IP address of the DNS Server in dotted decimal notation.

• From this DHCP interface

Specify from which DHCP-enabled interface a provided DNS server should be preferred.

DNS Proxy When DNS proxy is enabled, system will relay DNS requests to the currently configured

DNS server, and reply as a DNS resolver to the client devices on the network.

IP Interfaces

Delete Select this option to delete an existing IP interface.

VLAN The VLAN associated with the IP interface. Only ports in this VLAN will be able to access the

IP interface. This field is only available for input when creating a new interface.

IPv4 DHCP Enabled Enable the DHCP client by checking this box. If this option is enabled, the system will

configure the IPv4 address and mask of the interface using the DHCP protocol. The DHCP

client will announce the configured System Name as hostname to provide DNS lookup.

IPv4 DHCP Fallback

Timeout

The number of seconds for trying to obtain a DHCP lease. After this period expires, a

configured IPv4 address will be used as IPv4 interface address. A value of zero disables the

fallback mechanism, such that DHCP will keep retrying until a valid lease is obtained. Legal

values are 0 to 4294967295 seconds.

INS_CNGE24FX12TX12MS[POE] Rev. 2.22.18 PAGE 17

INSTRUCTION MANUAL CNGE24FX12TX12MS[POE]

TECH SUPPORT: 1.888.678.9427

Object Description

IPv4 DHCP Current

Lease

For DHCP interfaces with an active lease, this column shows the current interface address,

as provided by the DHCP server.

IPv4 Address The IPv4 address of the interface in dotted decimal notation.

If DHCP is enabled, this field configures the fallback address. The field may be left blank if

IPv4 operation on the interface is not desired - or no DHCP fallback address is desired.

IPv4 Mask The IPv4 network mask, in number of bits (prefix length). Valid values are between 0 and

30 bits for an IPv4 address.If DHCP is enabled, this field configures the fallback address

network mask. The field may be left blank if IPv4 operation on the interface is not desired -

or no DHCP fallback address is desired.

DHCPv6 Enable Enable the DHCPv6 client by checking this box. If this option is enabled, the system will

configure the IPv6 address of the interface using the DHCPv6 protocol.

DHCPv6 Rapid Commit Enable the DHCPv6 Rapid-Commit option by checking this box. If this option is enabled,

the DHCPv6 client terminates the waiting process as soon as a Reply message with a Rapid

Commit option is received. This option is only manageable when DHCPv6 client is enabled.

DHCPv6 Current Lease For DHCPv6 interface with an active lease, this column shows the interface address

provided by the DHCPv6 server.

IPv6 Address The IPv6 address of the interface. An IPv6 address is in 128-bit records represented as eight

fields of up to four hexadecimal digits with a colon separating each field (:). For example,

fe80::215:c5ff:fe03:4dc7. The symbol :: is a special syntax that can be used as a shorthand

way of representing multiple 16-bit groups of contiguous zeros; but it can appear only once.

It can also represent a legally valid IPv4 address. For example, ::192.1.2.34.

The field may be left blank if IPv6 operation on the interface is not desired.

IPv6 Mask The IPv6 network mask, in number of bits (prefix length). Valid values are between 1 and

128 bits for an IPv6 address.

The field may be left blank if IPv6 operation on the interface is not desired.

Default Gateway

Address The IP address of the gateway valid format is dotted decimal notation.

IP Routes

Delete Select this option to delete an existing IP route.

Network The destination IP network or host address of this route. Valid format is notation or a valid

IPv6 notation. A default route can use the value 0.0.0.0or IPv6 :: notation.

Mask Length The destination IP network or host mask, in number of bits (prefix length). It defines how

much of a network address that must match, in order to qualify for this route. Valid values

are between 0 and 32 bits respectively 128 for IPv6 routes. Only a default route will have a

mask length of 0 (as it will match anything).

Gateway The IP address of the IP gateway. Valid format is notation or a valid IPv6 notation. Gateway

and Network must be of the same type.

Next Hop VLAN

(Only for IPv6)

The VLAN ID (VID) of the specific IPv6 interface associated with the gateway. The given VID

ranges from 1 to 4094 and will be effective only when the corresponding IPv6 interface is

valid.

If the IPv6 gateway address is link-local, it must specify the next hop VLAN for the gateway.

If the IPv6 gateway address is not link-local, system ignores the next hop VLAN for the

gateway.

Add Interface Click to add a new IP Interface. A maximum of 8 interfaces is supported.

Add Route Click to add a new IP route. A maximum of 32 routes is supported.

INS_CNGE24FX12TX12MS[POE] Rev. 2.22.18 PAGE 18

INSTRUCTION MANUAL CNGE24FX12TX12MS[POE]

TECH SUPPORT: 1.888.678.9427

Object Description

Apply Click to apply changes.

Reset Click to revert to previous values.

INS_CNGE24FX12TX12MS[POE] Rev. 2.22.18 PAGE 19

INSTRUCTION MANUAL CNGE24FX12TX12MS[POE]

TECH SUPPORT: 1.888.678.9427

System NTP

Configure NTP on this page.

Object Description

Mode Indicates the NTP mode operation. Possible modes are: Enabled: Enable NTP client mode operation.

Disabled: Disable NTP client mode operation.

Server # Provide the IPv4 or IPv6 address of a NTP server. IPv6 address is in 128-bit records represented

as eight fields of up to four hexadecimal digits with a colon separating each field (:). For example,

‘fe80::215:c5ff:fe03:4dc7’. The symbol ‘::’ is a special syntax that can be used as a shorthand way

of representing multiple 16-bit groups of contiguous zeros; but it can appear only once. It can also

represent a legally valid IPv4 address. For example, ‘::192.1.2.34’.

Apply Click to apply changes.

Reset Click to revert to previous values.

INS_CNGE24FX12TX12MS[POE] Rev. 2.22.18 PAGE 20

INSTRUCTION MANUAL CNGE24FX12TX12MS[POE]

TECH SUPPORT: 1.888.678.9427

System Time

This page allows you to configure the Time Zone.

Object Description

Time Zone Configuration

Time Zone Lists various Time Zones worldwide. Select appropriate Time Zone from the drop down

Acronym User can set the acronym of the time zone. This is a User configurable acronym to identify the time zone. (

Range : Up to 16 characters )

Daylight Saving Time Configuration

Daylight

Saving

Time

This is used to set the clock forward or backward according to the configurations set below for a defined

Daylight Saving Time duration. Select ‘Disable’ to disable the Daylight Saving Time configuration. Select

‘Recurring’ and configure the Daylight Saving Time duration to repeat the configuration every year. Select

‘Non-Recurring’ and configure the Daylight Saving Time duration for single time configuration. ( Default :

Disabled )

Recurring Configurations

Start time settings

Week Select the starting week number.

Day Select the starting day.

Month Select the starting month.

Hours Select the starting hour.

Minutes Select the starting minute

End time settings

Week Select the ending week number.

Page is loading ...

Comnet CNGE24FX12TX12MS Series User manual

Comnet CNGE24FX12TX12MS Series User manual

Related papers

Other documents