SIMPLE MANUAL
Wireless
Sound Bar
To view the instructions of advanced features,
visit http://www.lg.com and then download Owner’s Manual.
Some of the content in this manual may differ from your unit.
MODEL
SH4
*MFL69392891*
www.lg.com
ENGLISH
Front Panel
··································Standby / On
·······························Selects Function
·························Adjusts Volume
Subwoofer Connection1
Rear Panel
OPTICAL IN · · · · · · · · · · · Connect to an Optical device
PORTABLE IN ········ Connect to a Portable device
USB port ················· Connect to a USB device
HDMI IN ········· Connect to HDMI out on a device
HDMI OUT (TV ARC) ·············· Connect to a TV
The buttons are located on the rear.
Place the wireless subwoofer near the speaker and
follow steps below.
a Connect the power cord of wireless subwoofer
to the outlet.
b Turn on the main unit. :
The sound bar and wireless subwoofer will be
automatically connected. The subwoofer's
green LED turns on.
Subwoofer Connection Manually
a Reset the Subwoofer
If the green LED on the subwoofer blinks quickly,
skip this step and go to b
• Press and hold Pairing button for 5 seconds.
• The LED lights up alternately in red and green.
• Plug out the power cord. After the LED turns
off completely, plug in the power cord again.
When the reset is completed, the subwoofer's green
LED blinks quickly.
b Reset the sound bar
• Adjust volume to minimum until the red LED
on the sound bar lights up for a while.
• Press and hold (Mute) button on the
remote control for 3 seconds.
• The red LED on the sound bar blinks quickly
• Turn the sound bar’s power off and on while
the subwoofer’s green LED blinks.
When the connection is completed, you can see the
green LED on the subwoofer.
Keep the sound bar and the subwoofer away
from the device (ex. wireless router, microwave
oven, etc.) over 1m to prevent wireless
interference.
>1m
ASC/STANDARD/CINEMA: Selects the sound effect.
NIGHT ON/OFF: Turns down the volume at night.
WOOFER LEVEL +/-: Adjusts the volume level of subwoofer.
AUTO POWER ON/OFF: Automatically turns on by an input
source.
Replacement of battery
Remote control
a Connect the the sound bar to the TV using
Optical cable.
b Set up [External Speaker (Optical)] on
your TV setting menu.
TV Connection 2
Optical Connection
HDMI(ARC) Connection
a Connect the sound bar to the TV using
HDMI cable.
b Set up [External Speaker (HDMI ARC)] on
your TV setting menu.
Connect with the Sound Bar and TV using
Optical ( ) or HDMI ARC ( ).
TV
TV
Addtional Device Connection
a Connect to the external device as follows.
TV
OR
(Set-top Box,
Player etc.)
b Set the input source by pressing F on the remote
control or unit repeatedly.
OR
HDMI connection is unavailable if your TV does
not support HDMI ARC.
Specication
Power
consumption
Refer to the main label.
Networked standby : 0.5 W
(If all network ports are
activated.)
AC adapter
y
Model :
DA-38A25
y
Manufacturer : Asian Power
Devices Inc.
y
Input :
100 - 240 V ~ 50 - 60 Hz
1.2 A
y
Output : 25 V
0
1.52 A
Dimensions
(W x H x D)
Approx.
890 mm x 53 mm x 85 mm
Without foot
Net Weight Approx. 2.34 kg
Bus Power Supply
(USB)
5 V 0 500 mA
Amplier(Total
RMS Output
power)
300 W
Designandspecicationsaresubjecttochangewithout
notice.
Declaration of Conformity
Hereby, LG Electronics European Shared Service Center B.V.,
declares that this Wireless Sound Bar is compliant with
the essential requirements and other relevant provisions
of Directive 1999/5/EC. The complete Declaration of
Conformity may be requested through the following postal
address:
LG Electronics European Shared Service Center B.V.
Krijgsman 1
1186 DM Amstelveen
The Netherlands
or can be requested at our dedicated DoC website:
http://www.lg.com/global/support/cedoc/cedoc#
This device is a 2.4 GHz and 5 GHz wideband transmission
system, intended for use in all EU member states and EFTA
countries.
IMPORTANT SAFETY NOTICE
The cord grip for the plug fitted to this product is
built into the existing power cord as supplied. If, for
any reason you need to shorten the cord.
DO NOT RE-USE THE PLUG.
A new plug must be used to ensure your continued
safety by securing the plug to the power cord in
accordance with Plug & Socket Regulations 1994.
Additional Information
/