Electrolux E30GC74GPS1 Installation guide

Brand: Electrolux

Model: E30GC74GPS1

Type: Installation guide

This manual is also suitable for

iNSTALLATiON AND SERVICE MUST BE PERFORMED BY

A QUALiFiED iNSTALLER.

iMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR'S USE.

READ AND SAVE THESE iNSTRUCTiONS FOR FUTURE REFERENCE.

If the information in this manual is not followed exactly, a fire or explosion may result causing

property damage, personal injury or death.

FOR YOUR SAFETY:

-- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other

appliance.

-- WHAT TO DO IF YOU SMELL GAS:

° Do not try to light any appliance.

° Do not touch any electrical switch; do not use any phone in your building.

° Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.

° If you cannot reach your gas supplier, call the fire department.

-- Installation and service must be performed by a qualified installer, service agency or the gas supplier.

For Standard

Installation:

Gas Cooktop Dimensions

* 30" (76.2 cm) rain. for

unprotected cabinet and

24" (61 cm) rain. for cabinet

with protected bottom surface.

GasCooktop Cutout

Dimensions 3"(7.6cm)

2"(5.1 cm) Dia.

Opening to route

power cable

4" X 4" (10.2 cmx 10.2

cm) opening to route gas

supply.

71/4

(18.4 cm)

Figure 1

**Note: D & Eare critical to the proper

installation of the cooktop. D reflects the

finished dimension. Due to the variation in

countertop materials, it isrecommended to first

undercut this dimension, and then adjust it

upon installation of the cooktop.

36 (91.4) 357/8 (91.1) 25 (63.5) 73A(19.7) 35_s/_ (91.3) 353/_ (89.4) 35%(89.2) 22 (55.9) 1% (2.9) Max. 772 (19.1)

30 (76.2) 297/8(75.9) 25(63.5) 73A(19.7) 29_s/_6(76) 293/_ (74.1) 2978(74) 22(55.9) 1%(2.9) Max. 772 (19.1)

All dimensions are stated in inches and (cm).

NOTE: Wiring diagrams for this cooktop are enclosed in this booklet

318201475 (0710) Rev. D

English - pages 1-8

Espaflol - p_iginas 9-16

Frangais - pages 17-23

Wiring Diagram page - 24

For Installation with the optional Stainless Steel Backsplash.

* 30" (76.2 cm) min. for

unprotected cabinet and

24" (61 cm) min. for cabinet

with protected bottom surface.

GasCooktop Dimensions

2" (5. I cm)

9" (22.9 cm)

Optional

Stainless Steel

Backsplash

***Note: Applies only in case

of countertop backwall.

4"X 4" (10.2 cm x 10.2 cm)

pening to route gas supply.

2" (5.1 cm)

opening to route

power cable.

GasCooktop Cutout Dimensions

Do not slide unit into cabinet cutout.

Protruding screws on the bottom of unit

may damage the bottom front finish.

21/2"

Figure 2

7Y4" (18.4 cm)

**Note: D & E are critical to the proper

installation of the cooktop. D reflectsthe

finished dimension. Due to the variation in

countertop materials, it isrecommended to first

undercut this dimension, and then adjust it

upon installation of the cooktop.

ii__i_!_!!__!!_!_______i__ii__i_iilli__i!_!i_ii_ii_!!_i!ii!iii!_!i_!ii!i_!ii_i_!_i_!!i!i!i!i¸iiii_i_!i_:i!_i_ii_ii_!i!ii_i_i__!ii!ii!ii!_i!_i_i!_!!ii!ii!!!!i_ii!ii!i_i_i_i_i_iiii_iii_i__ii!_!ii_iiiii_i_i_!i!i__!_!!!!__i_!!!_i__!__!____i_i__ii_i!_ii!!_!!i_i!_i!_i!_i!_i!_i!_iii_i!_i!_!!_!_!!_!!_!!_!!_!__i!___!i_!i_!i_!i_!i_!i_!i_!i__!i_ii_ii_ii_iii_iiiii_ii_ii!ii!ii!!iiiii!ii!i!!ii!i!ii!!i!i!i!ii!iiiiiii!!!!_i_i___i_i______!

i_i_';!il!i!ii_i'i:ii_;i:ilili!i__!i_i__i_iii!_iii!i!!_i,_i!i!i!i!_ii_ii!i!i!ili!!!i_i!_i_i_ii!_ii_!!i_i!i!i_i_i_i_!_i___i_i_i!__ii_Ii_i!_!__ii_ii_i_i_iIi,!iil!ii_!_i_!i_i!iii'ili_i'iiilliii_i!i_!,!__il_ii_ili!i_i_i_iii__i_!!ii!i_!i!i!i!_i!i!,iii!iii!i!i!_:i'il!_!ii_i_iiii!ii_:i!_ii_ii_fi'ili'ililiiilililil!i_!_!i_!i_!ii_ii_ii_iii_!ii_f__il_i_i_i_il!,_!i!i_i_i_i_i_!_:!_ii:i_ii:i_!_i_i_iii'i'i'i_ii'i_!iiiiiliiii_iiiij_i_i_i_i!_iiii_ii_ii_ii_ii_ii_i_iii_!__ii_;ii_ilii_i!_i!i_!iiiii!_i_i_i_iii_Iililii_i_i_i_i_!_i!ili__iij_i!!i_ili!_!il_iiii!i!_i!_i_i,il!ii!!ii_iil_!_IS!Ifi!!iii!_!:ii_iiii_ilii_i_i_i_i_i_i_ii_i!_!i!i_!_i_i_!_i_!_!_!_!_!!_i!i!_!!_i!_ill!_!_!_i!_ii_i!!i_ii_ii_iiiiii!i!i!i!i!i!i!iiiiiliiliii!!ii!_i_i_i_!_i_iji!i_ii_i_!!_ii!iiiil_i_!!_!_i_!_ii_ii_iiil_!i!!i!!_ii_ii_iiii_i_!_!ii!_!_!_i!!__!_!___!__,!!!_!_!__i_'i'!_!_!_!_!_!!i__!i_i_ii_!i_ii!i!i_i_i_i_i_!_!!!!!!!!!!!!!!illiliiil_!!!__i!_i_!'i'i'i_i_!_iii_il_i!_!i_i!iili!if_!_iilliiii_!__!i_ii_ii_i__!__i_!_'i_i:_ii_!,_ii!ii'ili_!i_,i!ii_!iiiii_i_i_ii_i_i_ili_ii!_i_!_!ii_!ii_i__!

36 (91.4) 35%(91.1) 25(63.5) 7_A(19.7) 35_s/_6(91.3) 35_A_(89.4 35_/_(89.2) 22(55.9) l_/_ (2.9) Max. 7Y_(19.1) 35_sA_(91.3)

30 (76.2) 29%(75.9) 25(63.5) 7_A(19.7) 29_s/_ (76) 29_/_ (74.1 29_/s(74) 22(55.9) 1%(2.9)Max. 7Y_(19.1) 29_s/_6(76)

All dimensions are stated in inches and (cm).

Important Notes to the Installer

1. Readallinstructionscontainedintheseinstallation

instructionsbeforeinstallingthecooktop.

2. Removeallpackingmaterialbeforeconnectingthe

electricalsupplytothecooktop.

3. Observeallgoverningcodesandordinances.

4. Besuretoleavetheseinstructionswiththeconsumer.

5. Note:Foroperationat2000ft.elevationsabovesee

level,applianceratingshallbereducedby4percent

foreachadditional1000ft.

Important Note to the Consumer

Keep these instructions with your Use and Care Guide for

future reference.

Depth Adjustment Filler Kit

This cooktop isdesigned to replace existing unit. Ifthe

depth of your countertop opening isbigger than 7Y4" (18.4

cm) and less than 8Y2" (21.6 cm) you can order a free filler

kit by calling ServiceCenter at 1-877-4ELECTROLUX(1-

877-435-3287).

For36" model: #903051-9010

For30" model: #903051-9100

Optional Items Available:

• A 9" (22.9 cm) Stainless Steel Backsplash Kit

#903048-9010 for 36" model or #903048-9100 for 30"

model.

A Black Knobs Kit #903049-9120 for 36" model or

#903049-9110 for 30" model.

Those kits can be order through the Service Center at

1-877-4ELECTROLUX(1-877-435-3287). However all cost

related to those kits will be at customer charges.

IMPORTANT SAFETY

INSTRUCTIONS

Installation of this cooktop must conform with local codes

or, in the absence of local codes, with the National Fuel

Gas Code ANSI Z223.1/NFPA54--1atest edition in the

United States, or in Canada, with the Canadian Fuel Gas

Code, CAN/CGA B149 and CAN/CGA B149.2.

This cooktop has been design certified by CSA

International. As with any appliance using gas and

generating heat, there are certain safety precautions you

should follow. You will find them in the Use and Care

Guide, read it carefully.

• Be sure your cooktop is installed and grounded

properly by a qualified installer or service

technician.

This cooktop must be electrically grounded in

accordance with local codes or, in their absence,

with the National Electrical Code ANSI/NFPA No.

70--latest edition in the United States, or in

Canada, with the Canadian Electrical Code, CSA

C22.1 Part 1.

• The burners can be lit manually during an

electrical power outage. To light a burner, hold a

lit match to the burner head, then slowly turn the

Surface Control knob to MTE. Use caution when

lighting burners manually.

• Do not store items of interest to children in

cabinets above the cooktop. Children could be

seriously burned climbing on the cooktop to reach

items.

• To eliminate the need to reach over the surface

burners, cabinet storage space above the burners

should be avoided.

• Adjust surface burner flame size so it does not

extend beyond the edge of the cooking utensil.

Excessive flame is hazardous.

• Never use your cooktop for warming or heating

the room, Prolonged use of the cooktop without

adequate ventilation can be hazardous.

• Do not store or use gasoline or other flammable

vapors and liquids near this or any other

appJiance. Explosions or fires could result.

The electrical power to the cooktop

must be shut off while gas line connections are

being made. FaiJure to do so couJd resuJt in serious

injury or death.

When installed in a manufactured (mobile) home

installation must conform with the Manufactured Home

Construction and Safety Standard, title 24 CFR,part

3280 [Formerly the Federal Standard for Mobile Home

Construction and Safety, title 24, HUD (part 280)] or,

when such standard is not applicable, the Standard for

Manufactured Home Installation, ANSI/NCSBCS A225. I

or with local codes where applicable.

13"(33cm)max.depth ,

forcabinetinstalledabove

cooktop

30"(76.2cm)Min.

ClearanceBetweenthe

TopoftheCooking

PlatformandtheBottom

ofanUnprotectedWood

orMetalCabinet

24"(61cm)Min.

whenBottomofWoodjlf

orMetalCabinetis

ProtectedbyNotLess

ThanI/8" Flame

RetardantMillboard

Covered With Not Less

Than No. 28 MGS

Sheet Steel, 0.015"

(0.4 mm) Stainless

Steel, 0.024" (0.6 mm)

Aluminum or 0.020"

(0.5 mm) Copper

"_-. _min

"l_ between rear edge of

cutout and nearest

combustible surface

18" (45.7 cm) P

Min.

30" (76.2 cm) min.

clearance between

the top of the

cooking platform and

the bottom of an

unprotected wood or

metal cabinet.

_To eliminate the risk of

burns or fire from reaching over heated

surfaces, cabinet storage space located

above the cooktop should be avoided. If

cabinet storage is provided, risk can be

reduced by installing a range hood that

projects horizontally a minimum of 7"

(17.8 cm) beyond the bottom of the

cabinets.

It isnot recommended to use

drawer underneath cooktop.

36" (91.4cm) 36" (91.4cm) 9" (22.9 cm) 9" (22.9 cm)

30" (76.2cm) 30" (76.2cm) 5" (12.7 cm) 5" (12.7 cm)

Figure 3 - CABINET DESIGN

Wall Outlet Location

_ 4,, -_

(10.2 cm)

(12.7 cm)

Recommended , I

area for 120V '1 |

grounded r,_ |

outlet on rear _4 CENTRE 16

wall. _LINE (40.6 cm)

OF UNIT

NOTE: If an

outlet is not I

available, have

one installed by I

a qualified :

technicS.

GCENTR E

LLINE

Figure 4 OFUNIT

Provide an Adequate Gas Supply

This cooktop isdesigned to operate on natural gas at 4"

(10.2 cm) of manifold pressure only.

A pressure regulator is connected in series with the

manifold on the cooktop and must remain in series with

the supply line.

For proper operation, the maximum inlet pressure to

the regulator must be no more than 14" (35.6 cm) of

water column (W.C.) pressure.

For checking the regulator, the inlet pressure must be at

least I "(2.5 cm) (or 2.5 kPa) greater than the regulator

manifold pressure setting. The regulator isset for 4"

(10.2 cm) of manifold pressure, the inlet pressure must

be at least 5" (12.7 cm).

The gas supply line to the range should be 1/2" (1.3 cm)

or 3/4" (1.9 cm) pipe,

LP/Propane Gas Conversion

This appliance can be used with Natural gas or LP/

Propane gas. It is shipped from the factory for use with

natural gas.

A kit for converting to LPgas is supplied with your

cooktop. The kit is marked "FOR LP/PROPANEGAS

CONVERSION".

The conversion must be performed by a qualified service

technician in accordance with the kit instructions and all

local codes and requirements. Failure to follow

instructions could result in serious injury or property

damage. The qualified agency performing this work

assumes responsibility for the conversion.

Failure to make the appropriate

conversion can result in serious personal injury and

property damage.

Important: Remove all packing material and

literature from cooktop before connecting gas and

electrical supply to cooktop.

Install Pressure Regulator

Install the pressure regulator with the arrow on the

regulator pointing up toward the unit in a position where

you can reach the access cap.

Do not make the connection too tight.

The regulator is die cast. Overtightening may crack the

regulator resulting in a gas leak and possible fire or

explosion.

Manual GAS FLOW Pressure

Shutoff Flare _" Flare Regulator

Valve Union Union

Nipple Flexible

Access

Off Connector

Cap

All connections must be wrench-tightened

Figure 5

Assemble the flexible connector from the gas supply pipe

to the pressure regulator in the following order:

1. manual shutoff valve

2. I/2" (1.3 cm) nipple

3. I/2" (1.3 cm) flare union adapter

4. flexible connector

5. I/2" (1.3 cm) flare union adapter

6. I/2" (1.3 cm) nipple

7. pressure regulator

Use pipe-joint compound made for use with Natural and

LP/Propane gas to seal all gas connections. If flexible

connectors are used, be certain connectors are not

kinked.

Thesupplylineshouldbeequippedwithanapproved

shutoffvalve.Thisvalveshouldbelocatedinthesame

roomasthecooktopandshouldbeinalocationthat

allowseaseofopeningandclosing.Donotblockaccess

totheshutoffvalve.Thevalveisforturningonor

shuttingoffgasto theappliance.

Shutoff Valve

Open position

Figure 6

Once the regulator is in place, open the shutoff valve in

the gas supply line. Wait a few minutes for gas to move

through the gas line.

Check for leaks. After connecting the cooktop to the

gas supply, check the system for leaks with a

manometer. If a manometer is not available, turn on the

gas supply and use a liquid leak detector (or soap and

water) at all joints and connections to check for leaks.

Do not use a flame to check for leaks

from gas connections. Checking for leaks with a flame

may result in a fire or explosion.

Tighten all connections if necessary to prevent gas

leakage in the cooktop or supply line.

Check alignment of control knob valves after

connecting the cooktop to the gas supply to be sure the

cooktop manifold pipe has not moved. A misalignment

could cause the valve stems to rub on the control panel,

resulting in a gas leak at the valve.

Disconnect this cooktop and its individual shutoff

valve from the gas supply piping system during any

pressure testing of that system at test pressures greater

than 1/2 psig (3.5 kPa or 14" (35.6 cm) water column).

Isolate the cooktop from the gas supply piping

system by closing its individual manual shutoff valve

during any pressure testing of the gas supply piping

system at test pressures equal to or less than 1/2 psig

(3.5 kPa or 14" (35.6 cm) water column).

Electrical Requirements

120 volt, 60 Hertz, properly grounded branch circuit

protected by a 15 amp circuit breaker or time delay fuse.

Do not use an extension cord with this cooktop.

Grounding Instructions

iMPORTANT Please read carefully.

For personal safety, this appliance must be properly

grounded.

The power cord of this appliance is equipped with a 3-

prong (grounding) plug which mates with a standard 3-

prong grounding wall receptacle (see Figure 7) to

minimize the possibility of electric shock hazard from the

appliance.

The wall receptacle and circuit should be checked by a

qualified electrician to make sure the receptacle is

properly grounded.

Preferred Method

Grounding type

wall receptacle

Do not, under

any circumstances

cut, remove,

or bypass the

grounding prong.

Power supply

cord with 3-prong

grounding plug.

Figure 7

Where a standard 2-prong wall receptacle is installed, it

isthe personal responsibility and obligation of the

consumer to have it replaced by a properly grounded 3-

prong wall receptacle.

Do not, under any circumstances, cut or remove the

third (ground) prong from the power cord.

Disconnect electrical supply cord from

wall receptacle before servicing cooktop.

Cooktop Installation

1. Visually inspect the cooktop for damage.

2. If you are installing the optional Stainless Steel

backsplash, first fix it at the back of the cooktop using

the screws supplied with the kit and follow the

instructions attached.

3. Set the cooktop into the countertop cutout.

NOTE: Do not use caulking compound; cooktop should

be removable for service when needed.

Check Operation

Refer to the Use and Care Guide packaged with the

cooktop for operating instructions and for care and

cleaning of your cooktop.

Do not touch the burners. They may be

hot enough to cause burns.

1. Burner Bases and Burner Caps

This range is equipped with sealed burners asshown

(Figure 8). All pieces are at their place. Take note where

they are. Remove all packaging material located

under the Dual Surface burner head. Make sure the

burner is properly aligned and leveled.

NOTE: There are no burner adjustments necessary on

this range.

30" Modem

Figure 8

4. Adjust the "LOW" Setting of Regular Burner (see

figure 8) on the Surface Burner Valves (Figure 9):

a. Push in and turn control to LITEuntil burner ignites.

b. Quickly turn knob to LOWEST POSITION.

c. If burner goes out, reset control to OFF.

d. Remove the surface burner control knob and

decorative ring.

e. Insert a thin-bladed screwdriver into the hollow valve

stem and engage the slotted screw inside. Flame size

can be increased or decreased by turning the screw.

Turn counterclockwise to increase flame size. Turn

clockwise to decrease flame size. Adjust flame until

you can quickly turn knob from LITEto LOWEST

POSITIONwithout extinguishing the flame. Flame

should be as small as possible without going out.

Note: Air mixture adjustment isnot required on surface

burners.

Burner Base

Dual Surface

Burner

36" model

Burner Cap

Fixed Burner Ring

and Burner Base

Regular Burner

Figure 9

2. Turn on Electrical Power and Open Main Shutoff

Gas Valve

3. Check the Igniters

Operation of electric igniters should be checked after

range and supply line connectors have been carefully

checked for leaks and range has been connected to

electric power. To check for proper lighting:

a.Push in and turn a surface burner knob to the LITE

position. All electronic surface ignitors will spark at the

same time. However, only the burner you are turning

on will ignite.

b.The surface burner should light once the flow of gas

reached the surface burner. Each burner should light

within four (4) seconds in normal operation after air

has been purged from supply lines. Visually check that

burner has lit.

c.Once the burner lights, the control knob should be

rotated out of the LITEposition.

There are separate ignition devicesfor each burner. Try each

knob separately until all burner valves have been checked.

5. Adjustthe "LOW"Settingof theDualBurner(see

Figure 8) on the Surface Burner Valve (Figure 10):

Note: On the dual valve the low setting of each portion

(rear portion of bridge burner and the center portion of

bridge burner) should be adjusted individually.

a. Push in and turn control to LITEuntil the rear portion

of the bridge burner ignites only.

b. Quickly turn knob to LOWEST POSITION.

c. If burner goes out, reset control to OFF.

d. Remove the surface burner control knob.

e. The inner portion of the dual burner flame size can be

increased or decreased by turning screw A (see Figure

19). Use screw B to adjust the flame size of the outer

portion of the dual burner. Turn counterclockwise the

screw to increase flame size. Turn clockwise the

screw to decrease flame size. Adjust flame until you

can quickly turn knob from LITEto LOWEST POSITION

without extinguishing the flame. Flame should be as

small as possible without going out.

Note: Air mixture adjustment isnot required on surface

burners.

When All Hookups are Complete

Make sure all controls are left inthe OFF position.

Before You Call for Service

Read the Before You Call for Service Checklist and

operating instructions in your Use and Care Guide, It

may save you time and expense. The list includes

common occurrences that are not the result of defective

workmanship or materials in this appliance.

Refer to your Use and Care Guide for Electrolux Service

phone numbers, or call 1-877-4ELECTROLUX (1-877-

435-3287).

Figure 10

Page is loading ...

TOP _R ]C_ll1_q

GPTI_

BOJG]E D"._-LL_E-BRdLEL_

T_P ELRNER I(_N[TER

Q_JE_ BE E]kICt:NDIBOSL_[{_

B_JGIE O'P,LLLP,AG_ BRULEL_

R i [:i,.ff

INT.ENC. _

CS_EO-=D

INTER. ALLL_I.

RICHT FRC_IT

INT, EN_. DE

N:_NTE _CF¢_

IN_, _U_t,

D. AV,

_ I aKI

INT. ENC. _-

INT+ENC+

T{_ _ I1:_1_1_ C_-NTROi;_Ull3:_

C_ ENCS_DIDO SL_,:_RIOR IN_I_L ALLL_.

EOJGIE D'_J-L_W_-E_LLEL_ C_TR_ _VANT

INT. ENC.

IZ(_JIE_OO

DE ENCO_IDO _t-RI_R Gj_q,

EOJGIE D-_L_EE-B_LLE_

I BK-I

_NT_ENC_ BE

_q_TER _O=LF BO_O FR_MTE _ZW_DO

BE MC_JLO BE _EENO_OO _N1ER_J-L_

G_AV_

I_NITER _LL E

CL,_Z_O BE _OJLO BE E_CENDIC_ C{7_NECTL_

_-_C CO_CTION ALLUP_LR o CONNECTEL_

-- FLESTA A TIE_A

_ARNIN_ MI_: A L_ 1EF_E R_:R O3_D

DIVOT R_:R B_'C_ S_:RVlC]NG LN],, p/_A 1W,_F=FO_/1E

_VlSO BE FU_:_A

DE_CTE L_ E CA_t-E

EL _WqrENIMIENT0 De_ ELECT_JDC_STICO.

DIE;O_ECT F_OUEREe=O_E S_RVlClN_ LNI_.

__ I 8 2OO 3304

LE C_AHT AWNT B'EFmETL_ LA

REP/_AT I _. _ 3_2t

_IBJ_C_ / N_ / NOIR UL _TYLE

_viso:

ETIGUET_ T0_6 LOS _ m_rES {_ D_CG_ECTAq PAR

y P_LI{_O_O.V_[_LE Sl EL FUmCI{_U_ENIO _SrA

O_FR_CT0 BESmJES BEL _'r_IN_ENTO.

AVERT [S_EME_qT:

ETIQ_JE_ Ct_OJE FIL AV/_qT LE BEB_E_I._E_T DE DEUX C].U_ _ DE

Ft_JT CAU_ U_ 0_t:RAT]_'_ _E_Rt:L_:,Vt:RIF[ER LE EO_

RDNCTI_NT {_ L'_P_EIL m:_ES TOUIE REpAF_T[0N.

LE_T FRONT LE_'T _ CENTER _ I(_N.S./. INT:E,_:. BE I(_N-SW.

I{_. 5g. IGN. SW. I(_N.S,a. INT. ENC. BE INT. ENC._RASERO

INT,E_, DE INT.E_C._ INT. Ei_E:. BE _Nffl_J _ FI:;_'rE [J_FCH0

_E IZI_JI_ IZ_J_JIEI_U3 _NTI_O IZ{_Jl_ DEF_:I31_0 IN_]_._. IN_E_,_L_,

INTER. _lJ_l. INT{J_./_U_UFI. IN_ER. J__LJ_I, IN_]_, A_L_, D. AV. D. ,_d_,

G.AV. G./_R. c_rrF_ AVOWal" _ _KE_E

TOPBL_,R_MERI_ITBR

G_E_E_ DE E_NOIBO 5L_I{_

_IE D'/_LU_E,E E_LLEL_

TCP _ [_ITI_

T(3P _ IGNITER

BE ENCe_DIDO SL_:_:_I_

T_ _ [_ITI_

DE ENC_D[DO _S_:RI_

<_ ,-04-

TO=:)BLOB'S::R ]{_IT_

DE ENCETq0[D0S:_ERICR

318047110 REV, A

C_UTION:

L_BEL ALL WI_ES pRUOR TO OISCONNECTIC_ _ SERVlCKNG COW_RCLS.

ETlaL_ TOLX_ LOS _L_I_S _N_ _ _ESCOh_CT_R _R

VERT _SSE_NT

F_L AVAN_

RIC_ F_T LEFT F_NT

D._W _._V.

LE_ r_ _C_T _E_

TC_ BL_R I{_UT_R

O_EHADOR

TOP _ER I_IT_

,'_,JEMA_ r_ ENCEN_BO SU_ER_O_

OZ_MAD_-_ E_ E_CENU_CO SUFEmIOR

L O-- --

" O--

BLOC CON_CT_ON _LLUMEU_

318047111 REV. B

Electrolux E30GC74GPS1 Installation guide

Brand: Electrolux

Model: E30GC74GPS1

Type: Installation guide

This manual is also suitable for

Download PDF

report

in other languages

français: Electrolux E30GC74GPS1 Guide d'installation
español: Electrolux E30GC74GPS1 Guía de instalación

Electrolux E30GC74GPS1 Installation guide

This manual is also suitable for

Electrolux E30GC74GPS1 Installation guide

in other languages

Related papers

Other documents