Dodge 2008 Caravan Owner's manual

TABLE OF CONTENTS

SECTION PAGE

1

INTRODUCTION

.............................................................3

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

...............................9

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

...............................93

4

UNDERSTANDING YOUR INSTRUMENT PANEL

................................... 215

5

STARTING AND OPERATING

.................................................305

6

WHAT TO DO IN EMERGENCIES

...............................................385

7

MAINTAINING YOUR VEHICLE

...............................................405

8

MAINTENANCE SCHEDULES

..................................................461

9

IF YOU NEED CONSUMER ASSISTANCE

..........................................469

10

INDEX

....................................................................479

1

2

3

4

5

6

7

8

9

10

INTRODUCTION

CONTENTS

m Introduction ...........................4

m How To Use This Manual ..................4

m Warnings And Cautions ...................6

m Vehicle Identification Number ...............6

m Vehicle Modifications/Alterations ............7

1

INTRODUCTION

This manual has been prepared with the assistance of

service and engineering specialists to acquaint you with

the operation and maintenance of your new vehicle. It is

supplemented by a Warranty Information Booklet and

various customer oriented documents. You are urged to

read these publications carefully. Following the instruc-

tions and recommendations in this manual will help

assure safe and enjoyable operation of your vehicle.

NOTE: After you read the manual, it should be stored

in the vehicle for convenient reference and remain with

the vehicle when sold, so that the new owner will be

aware of all safety warnings.

When it comes to service, remember that your dealer

knows your vehicle best, has the factory-trained techni-

cians and genuine Mopart parts, and is interested in

your satisfaction.

HOW TO USE THIS MANUAL

Consult the table of contents to determine which section

contains the information you desire.

The detailed index, at the rear of this manual, contains a

complete listing of all subjects.

Consult the following table for a description of the

symbols that may be used on your vehicle or throughout

this owner manual:

4 INTRODUCTION

INTRODUCTION 5

1

WARNINGS AND CAUTIONS

This manual contains WARNINGS against operating

procedures, which could result in an accident or bodily

injury. It also contains CAUTIONS against procedures,

which could result in damage to your vehicle. If you do

not read this entire manual, you may miss important

information. Observe all Warnings and Cautions.

VEHICLE IDENTIFICATION NUMBER

The vehicle identification number (VIN) is found on the

left front corner of the instrument panel, visible through

the windshield. This number also appears on the Auto-

mobile Information Disclosure Label affixed to a window

on your vehicle, the vehicle registration and title.

NOTE: It is illegal to remove the VIN.

Vehicle Identification Number

6 INTRODUCTION

VEHICLE MODIFICATIONS/ALTERATIONS

WARNING!

Any modifications or alterations to this vehicle could

seriously affect its roadworthiness and safety and

may lead to an accident resulting in serious injury or

death.

INTRODUCTION 7

1

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

CONTENTS

m A Word About Your Keys ..................13

▫ Wireless Ignition Node (WIN) .............13

▫ FOB With Integrated Key.................14

▫ Tip Start Feature .......................15

▫ Ignition Key Removal ...................15

▫ Key-In-Ignition Reminder ................16

▫ Locking Door With The Key ...............16

m Sentry Key ............................17

▫ Replacement Keys ......................18

▫ Customer Key (FOB) Programming ..........18

▫ General Information ....................19

m Steering Wheel Lock — If Equipped ..........20

▫ If You Wish To Manually Lock The Steering

Wheel ..............................20

▫ To Release The Steering Wheel Lock .........20

▫ Automatic Transaxle Ignition Interlock System . .20

m Security Alarm System — If Equipped .........20

▫ Rearming Of The System — If Equipped ......21

2

▫ To Arm The System .....................21

▫ To Disarm The System ...................21

▫ Security System Manual Override ...........22

m Illuminated Entry System — If Equipped .......22

m Remote Keyless Entry — If Equipped .........23

▫ To Unlock The Doors And Liftgate ..........24

▫ To Lock The Doors And Liftgate ............25

▫ Using The Panic Alarm ..................25

▫ To Open/Close Power Liftgate — If Equipped . .26

▫ To Open/Close Left Power Sliding Door —

If Equipped ..........................26

▫ To Open/Close Right Power Sliding Door —

If Equipped ..........................27

▫ To Turn Off Flash Lights With Remote Key Lock —

If Equipped ..........................27

▫ General Information ....................28

▫ Transmitter Battery Service ...............28

m Remote Starting System — If Equipped ........29

m Door Locks ............................31

▫ Manual Door Locks .....................31

▫ Power Door Locks — If Equipped ..........32

m Windows .............................35

▫ Power Vent Windows — If Equipped ........35

▫ Power Windows .......................36

m Sliding Side Door ........................41

▫ Sliding Door Open Flash .................42

10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

▫ Power Sliding Door — If Equipped .........42

▫ Power Sliding Door Master Lock—

If Equipped ..........................44

▫ Child Protection Door Lock ...............45

m Liftgate ...............................47

▫ Power Liftgate — If Equipped .............48

m Seat Storage Bin Safety Warning .............51

▫ Storage Bin Cover Emergency Release ........52

▫ Reinstalling Storage Bin Cover Emergency

Release .............................53

m Occupant Restraints ......................54

▫ Lap/Shoulder Belts .....................55

▫ Automatic Locking Retractors (ALR) Mode –

If Equipped ..........................61

▫ Seat Belt Pretensioners ...................61

▫ Enhanced Seat Belt Use Reminder System

(BeltAlertt) ..........................62

▫ Seat Belts And Pregnant Women ............63

▫ Seat Belt Extender ......................63

▫ Supplemental Restraint System (SRS) - Airbag . .64

▫ Airbag System Components ...............64

▫ Front Seat Airbag Features ................65

▫ Airbag Deployment Sensors And Controls .....70

▫ Event Data Recorder (EDR) ...............75

▫ Child Restraint ........................77

m Rear Seat Delete Feature (Commercial Vehicles

Only) — If Equipped .....................85

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11

2

▫ Restraining Infants And Small Children With

Seat Delete Feature (Commercial Vehicles

Only) ...............................86

m Engine Break-In Recommendations ...........88

m Safety Tips ............................89

▫ Transporting Passengers .................89

▫ Lock Your Vehicle ......................89

▫ Exhaust Gas ..........................89

▫ Safety Checks You Should Make Inside The

Vehicle ..............................91

▫ Periodic Safety Checks You Should Make

Outside The Vehicle ....................92

12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

A WORD ABOUT YOUR KEYS

Your vehicle uses a keyless ignition system. This system

consists of a Fob with Integrated Key and a Wireless

Ignition Node (WIN) with integral ignition switch. You

can insert the double-sided integrated key into the igni-

tion switch with either side up.

Wireless Ignition Node (WIN)

The Wireless Ignition Node (WIN) operates similar to an

ignition switch. It has four operating positions, three of

which are detented and one spring-loaded. The detented

positions are LOCK, ACC, and ON. The START position

is a spring-loaded momentary contact position. When

released from the START position, the switch automati-

cally returns to the detented ON position.

Wireless Ignition Node (WIN)

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13

2

Fob with Integrated Key

The Fob with Integrated Key operates the ignition switch.

It also contains the Remote Keyless Entry (RKE) trans-

mitter and a valet key, which stores in the rear of the Fob.

The valet key allows for entry into the vehicle should the

battery in the vehicle or the Fob go dead. The valet key is

also for locking the glove box. You can keep the valet key

with you when valet parking.

To remove the valet key from the Fob, slide the mechani-

cal latch at the top of the Fob sideways with your thumb

and then pull the key out of the Fob with your other

hand.

NOTE: You can insert the double-sided valet key into

the lock cylinders with either side up.

Valet Key Removal

14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Tip Start Feature

Do not press the accelerator. Use the Fob with Integrated

Key to briefly turn the ignition switch to the START

position and release it as soon as the starter engages. The

starter motor will continue to run, and it will disengage

automatically when the engine is running.

Ignition Key Removal

Place the selector lever in “P” (Park). Turn the key to the

LOCK position and then remove the key.

NOTE: The power window switches, radio, power

outlets, and removable console (if equipped), will remain

active for up to 45 seconds after the ignition switch has

been turned off. Opening a vehicle front door will cancel

this feature.

WARNING!

NEVER leave children alone in a vehicle. Leaving

children in a vehicle unattended is dangerous for a

number of reasons. A child or others could be seri-

ously or fatally injured. Don’t leave the keys in the

ignition. A child could operate power windows,

other controls, or move the vehicle

CAUTION!

An unlocked car is an invitation to thieves. Always

remove key from the ignition and lock all doors

when leaving the vehicle unattended.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15

2

Key-In-Ignition Reminder

If you open the driver’s door and the key is in the

ignition, a chime will sound to remind you to remove the

key.

NOTE: The Key-In-Ignition reminder only sounds

when the ignition key is placed in the LOCK or ACC

position.

Locking Door With The Key

The driver’s door has the only external lock cylinder. You

can insert the key with either side up. To manually lock

the door, turn the key rearward, to unlock the door, turn

the key forward. See Section 7 of this manual for door

lock lubrication.

Valet Key Removal

16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

SENTRY KEY

The Sentry Key Immobilizer System prevents unautho-

rized vehicle operation by disabling the engine. The

system does not need to be armed or activated. Operation

is automatic, regardless of whether the vehicle is locked

or unlocked.

The system uses the factory-mated Fob with Integrated

Key and Wireless Ignition Node (WIN) to prevent unau-

thorized vehicle operation. Therefore, only Fobs that are

programmed to the vehicle can be used to start and

operate the vehicle. The system will shut the engine off in

two (2) seconds if someone uses an invalid Fob to start

the engine.

After turning the ignition switch to the ON position, the

Vehicle Security Alarm Indicator Light will turn on for

three (3) seconds for a bulb check. If the light remains on

after the bulb check, it indicates that there is a problem

with the electronics. In addition, if the light begins to

flash after the bulb check, it indicates that someone used

an invalid Fob to start the engine. Either of these condi-

tions will result in the engine being shut off after two (2)

seconds.

If the Vehicle Security Alarm Indicator Light turns on

during normal vehicle operation (vehicle running for

longer than 10 seconds), it indicates that there is a fault in

the electronics. Should this occur, have the vehicle ser-

viced as soon as possible.

NOTE:

•

The Sentry Key Immobilizer System is not compatible

with aftermarket remote starting systems. Use of these

systems may result in vehicle starting problems and

loss of security protection.

•

Exxon/Mobil Speed Pass,™ additional Fobs, or any

other transponder-equipped components on the same

key chain will not cause a fault unless the additional

part is physically held against the Fob being used to

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17

2

start the vehicle. Cell phones, pagers, or other RF

electronics will not cause interference with this system.

All of the Fobs provided with your new vehicle have

been programmed to the vehicle electronics.

Replacement Keys

NOTE: Only Fobs that are programmed to the vehicle

electronics can be used to start and operate the vehicle.

Once a Fob is programmed to a vehicle, it cannot be

programmed to any other vehicle.

CAUTION!

Always remove Sentry Keys from the vehicle and

lock all doors when leaving the vehicle unattended.

At the time of purchase, the original owner is provided

with a four-digit PIN number. Keep the PIN in a secure

location. This number is required for dealer replacement

of Fobs. Duplication of Fobs may be performed at an

authorized dealer or by using the Customer Key Pro-

gramming procedure. This procedure consists of pro-

gramming a blank Fob to the vehicle electronics. A blank

Fob is one, which has never been programmed.

NOTE: When having the Sentry Key Immobilizer

System serviced, bring all vehicle Fobs with you to the

dealer.

Customer Key (Fob) Programming

If you have two valid sentry keys, you can program new

sentry keys to the system by performing the following

procedure:

1. Insert the first valid key into the ignition switch and

turn the ignition switch ON for at least 3 seconds but no

longer than 15 seconds. Turn the ignition switch OFF and

remove the first key.

18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

2. Insert the second valid key and turn the ignition

switch ON within 15 seconds. After ten seconds, a chime

will sound and the Vehicle Security Alarm Indicator

Light will begin to flash. Turn the ignition switch OFF

and remove the second key.

3. Insert a blank Sentry Key into the ignition switch and

turn the ignition switch ON within 60 seconds. After 10

seconds, a single chime will sound and the Vehicle

Security Alarm Indicator Light will stop flashing, turn on

again for 3 seconds, and then turn off.

The new Sentry Key is programmed. The Keyless Entry

Transmitter will also be programmed during this pro-

cedure.

Repeat this procedure to program up to 8 keys. If you do

not have a programmed sentry key, contact your dealer

for details.

NOTE: If a programmed key is lost, see your dealer to

have all remaining keys erased from the systems

memory. This will prevent the lost key from starting your

vehicle. The remaining keys must then be repro-

grammed. All vehicle keys must be taken to the dealer at

the time of service to be reprogrammed.

General Information

The Sentry Key system complies with FCC rules part 15

and with RSS-210 of Industry Canada. Operation is

subject to the following conditions:

•

This device may not cause harmful interference.

•

This device must accept any interference that may be

received, including interference that may cause undes-

ired operation.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19

2

STEERING WHEEL LOCK — IF EQUIPPED

Your vehicle may be equipped with a passive steering

wheel lock. This lock prevents steering the vehicle with-

out the FOB Integrated Key. If the steering wheel is

moved no more than 1/2 turn in either direction and the

FOBIK is not in the ignition switch, the steering wheel

will lock.

If You Wish To Manually Lock The Steering

Wheel:

With the engine running, turn the steering wheel upside

down, turn off the engine and remove FOB Integrated

Key. Turn the steering wheel slightly in either direction

until the lock engages.

To Release The Steering Wheel Lock:

Insert the FOB Integrated Key in the ignition switch and

start the engine. If the key is difficult to turn, move the

wheel slightly to the right or left to disengage the lock.

NOTE: If you turned the wheel to the right to engage

the lock, you must turn the wheel slightly to the right to

disengage it. If you turned the wheel to the left to engage

the lock, turn the wheel slightly to the left to disengage it.

Automatic Transaxle Ignition Interlock System

This system prevents the key from being removed unless

the shift lever is in PARK. It also prevents shifting out of

PARK unless the key is in the ACC, or ON/RUN

positions, and the brake pedal is depressed.

SECURITY ALARM SYSTEM — IF EQUIPPED

This system monitors the vehicle doors and ignition for

unauthorized operation. When the alarm is activated, the

system provides both audible and visual signals. For the

first 3 minutes the horn will sound and the headlights

and security telltale will flash repeatedly. For an addi-

tional 15 minutes only the headlights and security telltale

20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Page is loading ...

Dodge 2008 Caravan Owner's manual

This manual is also suitable for

Dodge 2008 Caravan Owner's manual

Related papers

Other documents