Poulan 530088788 User manual

Brand: Poulan

Model: 530088788

Category: Power chainsaws

Type: User manual

This manual is also suitable for

3450
3750

3450 / 3750

Operator’s Manual

Manual del Operador

Manuel de L’utilisateur

WARNING:

Read and follow all Safety Rules and Operating Instructions before

using this product. Failure to do so can result in serious injury.

ADVERTENCIA:

Lea el manual del operador y siga todas las advertencias e enstruc-

ciones de seguridad. El no hacerlo puede resultar en lesiones

graves.

AVERTISSEMENT:

Lire le manuel de l’utilisateur et bien respecter tous les avertisse-

ments et toutes les instructions de sécurité. Tout défaut de le faire

pourrait entraîner des blessures graves.

ENGLISH

ESP AÑOL

FRANÇAIS

530088788 11/17/00

Please do not return unit to retailer .

Por favor, no devuelva el aparato al lugar de compra.

Veuillez ne pas retourner l’outil au détaillant.

1--800--554--6723

www.poulan.com

For Occasional Use Only

Electrolux Home Products

North America

Div. of WCI Outdoor Products, Inc.

Augusta, GA 30907

2000 WCI Outdoor Products, Inc.

SAFETY RULES

WARNING:

Always disconnect

spark plug wire and place wire where it can-

not contact spark plug to prevent accidental

starting when setting up, transporting, ad-

justing or making repairs except carburetor

adjustments.

Because a chain saw is a high-speed wood-

cutting tool, special safety precautions must

be observed to reduce the risk of accidents.

Careless or improper use of this tool can

cause serious injury.

PLAN AHEAD

Read this manual carefully until you com-

pletely understand and can follow all safe-

ty rules, precautions, and operating in-

structions before attempting to use the

unit.

Restrict the use of your saw to adult users

who understand and can follow safety

rules, precautions, and operating instruc-

tions found in this manual.

Snug

Fitting

Clothing

Safety

Shoes

Safety Chaps

Heavy Duty

Gloves

Eye

Protection

Hearing

Protection

Safety Hat

Wear protective gear. Always use steel-

toed safety footwear with non-slip soles;

snug-fitting clothing; heavy-duty, non-slip

gloves; eye protection such as non-fog-

ging, vented goggles or face screen; an

approved safety hard hat; and sound barri-

ers (ear plugs or mufflers) to protect your

hearing. Regular users should have hear-

ing checked regularly as chain saw noise

can damage hearing. Secure hair above

shoulder length.

Keep all parts of your body away from the

chain when the engine is running.

Keep children, bystanders, and animals a

minimum of 30 feet (10 Meters) away from

the work area. Do not allow other people or

animals to be near the chain saw when

starting or operating the chain saw.

Do not handle or operate a chain saw

when you are fatigued, ill, or upset, or if you

have taken alcohol, drugs, or medication.

You must be in good physical condition

and mentally alert. Chain saw work is

strenuous. If you have any condition that

might be aggravated by strenuous work,

check with your doctor before operating a

chain saw.

Carefully plan your sawing operation in ad-

vance. Do not start cutting until you have a

clear work area, secure footing, and, if you

are felling trees, a planned retreat path.

OPERATE YOUR SAW SAFELY

Do not operate a chain saw with one hand.

Serious injury to the operator, helpers, by-

standers or any combination of these per-

sons may result from one-handed opera-

tion. A chain saw is intended for

two-handed use.

Operate the chain saw only in a well-venti-

lated outdoor area.

Do not operate saw from a ladder or in a

tree, unless you are specifically trained to

do so.

Make sure the chain will not make contact

with any object while starting the engine.

Never try to start the saw when the guide

bar is in a cut.

Do not put pressure on the saw at the end

of the cut. Applying pressure can cause

you to lose control when the cut is com-

pleted.

Stop the engine before setting the saw

down.

Do not operate a chain saw that is dam-

aged, improperly adjusted, or not com-

pletely and securely assembled. Always

replace bar, chain, hand guard, or chain

brake immediately if it becomes damaged,

broken or is otherwise removed.

With the engine stopped, hand carry the

chain saw with the muffler away from your

body, and the guide bar and chain to the

rear, preferably covered with a scabbard.

MAINTAIN YOUR SAW IN GOOD

WORKING ORDER

Have all chain saw service performed by a

qualified service dealer with the exception

of the items listed in the maintenance sec-

tion of this manual. For example, if improp-

er tools are used to remove or hold the fly-

wheel when servicing the clutch, structural

damage to the flywheel can occur and

cause the flywheel to burst.

Make certain the saw chain stops moving

when the throttle trigger is released. For

correction, refer to CARBURETOR AD-

JUSTMENTS.

Never modify your saw in any way.

Keep the handles dry, clean, and free of oil

or fuel mixture.

Keep fuel and oil caps, screws, and fas-

teners securely tightened.

Use only Poulan or Poulan Pro accesso-

ries and replacement parts as recom-

mended.

HANDLE FUEL WITH CAUTION

Do not smoke while handling fuel or while

operating the saw.

Eliminate all sources of sparks or flame in

the areas where fuel is mixed or poured.

There should be no smoking, open flames,

or work that could cause sparks. Allow en-

gine to cool before refueling.

Mix and pour fuel in an outdoor area on

bare ground; store fuel in a cool, dry, well

ventilated place; and use an approved,

marked container for all fuel purposes.

Wipe up all fuel spills before starting saw.

Move at least 10 feet (3 meters) from fuel-

ing site before starting engine.

Turn the engine off and let saw cool in a

non-combustible area, not on dry leaves,

straw, paper, etc. Slowly remove fuel cap

and refuel unit.

Store the unit and fuel in an area where fuel

vapors cannot reach sparks or open

flames from water heaters, electric motors

or switches, furnaces, etc.

KICKBACK

WARNING:

Kickback can occur

when the moving chain contacts an object at

the upper portion of the tip of the guide bar or

when the wood closes in and pinches the

saw chain in the cut. Contact at the upper

portion of the tip of the guide bar can cause

the chain to dig into the object, which stops

the chain for an instant. The result is a light-

ning fast, reverse reaction which kicks the

guide bar up and back toward the operator. If

the saw chain is pinched along the top of the

guide bar, the guide bar can be driven rapidly

back toward the operator. Either of these

reactions can cause loss of saw control

which can result in serious injury. Guard

against kickback

Rotational Kickback is the rapid upward

and backward motion of the chain saw that

can occur when the moving saw chain near

the upper portion of the tip of the guide bar

contacts an object such as a log or a branch.

Pinch-Kickback and Pull-In occur when

the chain is suddenly stopped by being

pinched, caught, or by contacting a foreign

object in the wood. This sudden stopping of

the chain results in a reversal of the chain

force used to cut wood and causes the saw

to move in the opposite direction of the chain

rotation. Pinch-Kickback drives the saw

straight back toward the operator. Pull-In

pulls the saw away from the operator. Either

reaction can result in loss of control and seri-

ous injury.

A v oid Pinch--Kickback:

Be extremely aware of situations or ob-

structions that can cause material to pinch

the top of or otherwise stop the chain.

Do not cut more than one log at a time.

Do not twist the saw as the bar is with-

drawn from an undercut when bucking.

Avoid Pull-- I n:

Always begin cutting with engine at full

speed and saw housing against wood.

Use wedges made of plastic or wood. Nev-

er use metal to hold the cut open.

Kickback Path

Avoid Obstructions

Clear The Working Area

REDUCE THE CHANCE OF

KICKBACK

Recognize that kickback can happen.

With a basic understanding of kickback,

you can reduce the element of surprise

which contributes to accidents.

Never let the moving chain contact any ob-

ject at the tip of the guide bar.

Keep the working area free from obstruc-

tions such as other trees, branches, rocks,

fences, stumps, etc. Eliminate or avoid

any obstruction that your saw chain could

hit while you are cutting through a particu-

lar log or branch.

Keep your saw chain sharp and properly

tensioned. A loose or dull chain can in-

crease the chance of kickback occurring.

Follow manufacturer ’s chain sharpening

and maintenance instructions. Check ten-

sion at regular intervals with the engine

stopped, never with engine running. Make

sure the bar clamp nuts are securely tight-

ened after tensioning the chain.

Begin and continue cutting at full speed. If

chain is moving at a slower speed, there is

greater chance of kickback occurring.

Cut one log at a time.

Use extreme caution when re-entering a

previous cut.

Do not attempt cuts starting with the tip of

the bar (plunge cuts).

Watch for shifting logs or other forces that

could close a cut and pinch or fall into chain.

Use Reduced- Kickback Guide Bar and Low-

Kickback Chain specified for your saw.

MAINTAIN CONTROL

Never reverse

hand positions

Stand to the left of

the saw

Thumb on underside of

handlebar

Elbow locked

Keep a good, firm grip on the saw with both

hands when the engine is running and

don’t let go. A firm grip will help you reduce

kickback and maintain control of the saw.

Keep the fingers of your left hand encir-

cling and your left thumb under the front

handlebar. Keep your right hand complete-

ly around the rear handle whether your are

right handed or left handed. Keep your left

arm straight with the elbow locked.

Position your left hand on the front handle-

bar so it is in a straight line with your right

hand on the rear handle when making

bucking cuts. Never reverse right and left

hand positions for any type of cutting.

Stand with your weight evenly balanced on

both feet.

Stand slightly to the left side of the saw to

keep your body from being in a direct line

with the cutting chain.

Do not overreach. You could be drawn or

thrown off balance and lose control of saw.

Do not cut above shoulder height. It is diffi-

cult to maintain control of saw above

shoulder height.

KICKBACK SAFETY FEATURES

WARNING:

The following features

are included on your saw to help reduce the

hazard of kickback; however, such features

will not totally eliminate this dangerous reac-

tion. As a chain saw user, do not rely only on

safety devices. You must follow all safety

precautions, instructions, and maintenance

in this manual to help avoid kickback and

other forces which can result in serious

injury.

Reduced-Kickback Guide Bar, designed

with a small radius tip which reduces the

size of the kickback danger zone on bar

tip. A Reduced-Kickback Guide Bar has

been demonstrated to significantly reduce

the number and seriousness of kickbacks

when tested in accordance with safety re-

quirements for gasoline powered chain

saws as set by ANSI B175.1.

Small Radius T ip

Symmetrical Guide Bar

Reduced Kickback Symmetrical Guide Bar

Large Radius Tip

Low-Kickback Chain, designed with a

contoured depth gauge and guard link

which deflect kickback force and allow

wood to gradually ride into the cutter. Low-

Kickback Chain has met kickback per-

formance requirements when tested on a

representative sample of chain saws be-

low 3.8 cubic inch displacement specified

in ANSI B175.1.

Low--Kickback

Chain

Not a Low--Kickback Chain

Can Obstruct

Material

Contoured Depth Gauge

Elongated Guard Link

Deflects Kickback

Force A nd Allows

Wood To Gradually

Ride Into Cutter

Handguard, designed to reduce the

chance of your left hand contacting chain if

your hand slips off the front handlebar.

Position of front and rear handlebars, de-

signed with distance between handles and

“in-line” with each other. The spread and

“in-line” position of the hands provided by

this design work together to give balance

and resistance in controlling t he pivot of

the saw back toward the operator if kick-

back occurs.

CHAIN BRAKE

Chain Brake, designed to stop the chain in

the event of kickback.

WARNING:

WE DO NOT REP-

RESENT AND YOU SHOULD NOT AS-

SUME THAT THE CHAIN BRAKE WILL

PROTECT YOU IN THE EVENT OF A

KICKBACK. Kickback is a lightning fast ac-

tion which throws the bar and rotating chain

back and up toward the operator. Kickback

can be caused by allowing contact of the bar

tip in the danger zone with any hard object.

Kickback can also be caused by pinching the

saw chain along the top of the guide bar. This

action may push the guide bar rapidly back

toward the operator. Either of these events

may cause you to lose control of the saw

which could result in serious injury or even

death. DO NOT RELY UPON ANY OF THE

SAFETY DEVICES BUILT INTO YOUR

SAW. YOU SHOULD USE THE SAW

PROPERLY AND CAREFULLY TO AVOID

KICKBACK. Reduced--kickback guide bars

and low--kickback saw chains reduce the

chance and magnitude of kickback and are

recommended. Your saw has a low kick-

back chain and bar as original equipment.

Repairs on a chain brake should be made by

an authorized servicing dealer. Take your

unit to the place of purchase if purchased

from a servicing dealer, or to the nearest au-

thorized master service dealer.

Tip contact in some cases may cause a

lightning fast reverse REACTION, kicking

guide bar up and back toward operator.

Pinching the saw chain along the top of the

guide bar may push the guide bar rapidly

back toward the operator.

Either of these reactions may cause you to

lose control of the saw which could result

in serious injury. Do not rely exclusively

upon safety devices built into your saw.

NOTE

: If this saw is to be used for commer-

cial logging, a chain brake is required and

shall not be removed or otherwise disabled

to comply with Federal OSHA Regulations

for Commercial Logging. Contact your Au-

thorized Service Dealer or call

1--800--554--6423.

SAFETY NOTICE:

Exposure to

vibrations through prolonged use of gasoline

powered hand tools could cause blood

vessel or nerve damage in the fingers,

hands, and joints of people prone to

circulation disorders or abnormal swellings.

Prolonged use in cold weather has been

linked to blood vessel damage in otherwise

healthy people. If symptoms occur such as

numbness, pain, loss of strength, change in

skin color or texture, or loss of feeling in the

fingers, hands, or joints, discontinue the use

of this tool and seek medical attention. An

anti-vibration system does not guarantee the

avoidance of these problems. Users who

operate power tools on a continual and

regular basis must monitor closely their

physical condition and the condition of this

tool.

SPECIAL NOTICE:

Your saw is equipped

with a temperature limiting muffler and spark

arresting screen which meets the

requirements of California Codes 4442 and

4443. All

U.S.

forest land and the s tates of

California, Idaho, Maine, Minnesota, New

Jersey, Oregon, and Washington require

many internal combustion engines to be

equipped with a spark arresting screen by

law. If you operate a chain saw in a state or

locale where such regulations exist, you are

legally responsible for maintaining the

operating condition of these parts. Failure to

do so is a violation of the law . Refer to the

SERVICE section for maintenance of the

spark arresting screen.

STANDARDS:

This saw is listed by Un-

derwriter ’s Laboratories, Inc., in accordance

with American National Standards for Gaso-

line--Powered Chain Saw Safety Require-

ments (ANSI B175.1-1991).

Failure to follow all Safety Rules and Precau-

tions can result in serious injury. If situations

occur which are not covered in this manual,

use care and good judgement. If you need

assistance, contact your Authorized Service

Dealer.

ASSEMBLY

Protective gloves (not provided) should be

worn during assembly.

ATTACHING THE BAR & CHAIN

(If not

already attached)

WARNING:

If received assembled,

repeat all steps to ensure your saw is proper-

ly assembled and all fasteners are secure.

Always wear gloves when handling the

chain. The chain is sharp and can cut you

even when it is not moving!

Loosen and remove the chain brake nuts

and the chain brake from the saw.

Remove the plastic shipping spacer (if

present).

Chain Brake

Chain Brake Nuts

Assembly

Tool

Shipping

Spacer

An adjusting pin and screw is used to ad-

just the tension of the chain. It is very im-

portant when assembling the bar, that the

pin located on the adjusting screw aligns

into a hole in the bar. Turning the screw will

move the adjustment pin up and down the

screw. Locate this adjustment before you

begin mounting the bar onto the saw . See

illustration below.

Adjustment

Screw

Turn the adjusting screw counterclock-

wise to move the adjusting pin almost as

far as it will go to the rear. This should allow

the pin to be near the correct position. Fur-

ther adjustment may be necessary as you

mount the bar.

Mount the bar as illustrated.

Slide the bar toward the rear of the saw as

far as possible.

Prepare the chain by checking the proper

direction. Without following the illustration

it is easy to place the chain on the saw the

wrong direction. Use the illustration of the

chain to determine the proper direction.

Place the chain onto the sprocket located

behind the clutch drum (see illustration).

Fit the chain between the teeth in the

sprocket.

Start at the top of the bar and fit chain into

groove around the guide bar.

After chain is installed, pull bar forward un-

til chain is snug in the groove of the bar.

Hold guide bar against the saw frame mak-

ing sure the adjusting pin is aligned with

the hole in the bar. Remember this pin

moves the bar forward and backward as

screw is turned. Install the chain brake.

Replace the chain brake nuts and tighten

finger tight. Once the chain is tensioned

you will need to tighten chain brake nuts.

Install the bar

Proper chain direction

Tip of Bar

Place chain onto the sprocket

CHAIN TENSION

(Including units with

chain already installed)

NOTE

: When adjusting chain tension,

make sure the bar nuts are finger tight only.

Attempting to tension the chain when the bar

nuts are tight can cause damage.

Checking the tension:

Use the screwdriver end of the chain adjust-

ment tool (bar tool) to move the chain around

the bar. If the chain does not rotate, it is too

tight. If too loose, the chain will sag below the

bar.

Adjusting the tension:

Chain tension is very important. Chain

stretches during use. This is especially true

during the first few times you use your saw.

Always check chain tension each time you

use and refuel your saw.

Adjusting

Screw

You can adjust chain tension by loosening

the bar clamp nuts and turning adjusting

screw 1/4 of a turn while lifting up on the bar.

If chain is too tight, turn adjusting

screw 1/4 turn counterclockwise.

If chain is too loose, turn adjusting

screw 1/4 turn clockwise.

Lift up the tip of the bar and tighten the bar

clamp nuts with the combination screw-

driver/wrench.

Recheck chain tension. Tension is correct

when chain does not sag below the bar but

still can be moved around the bar.

WARNING:

If the chain is operated

with a loose chain, the chain could jump off

the guide bar and result in serious injury.

OPERATION

KNOW YOUR SAW

READ THIS OPERATOR’S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR

CHAIN SAW. Compare the illustrations with your unit to familiarize yourself with the location of

the various controls and adjustments. Save this manual for future reference.

Bar Tool

Fuel Mix Fill Cap

Starter Housing

Bar Oil

Fill Cap

Chain

Front Hand Guard

Front Handle

Starter Rope

ON/STOP

Switch

Adjusting

Screw

Choke Knob

Guide Bar

Chain Brake Nuts

Cylinder Cover

Throttle

Lockout

Rear

Handle

Throttle

Trigger

Chain Brake

Direction

of Chain

Travel

Fast Idle

Lock

ON/STOP SWITCH

The ON/STOP SWITCH is used to stop the

engine.

THROTTLE TRIGGER

The THROTTLE TRIGGER controls engine

speed.

THROTTLE LOCK--OUT

The THROTTLE LOCK--OUT must be

pressed before you can squeeze the throttle

trigger. This feature prevents you from acci-

dentally squeezing the trigger.

FAST IDLE LOCK

The FAST IDLE LOCK holds the throttle trig-

ger in the starting position. Activate the fast

idle lock by pressing the throttle lock--out and

squeezing the throttle trigger. WIth the

throttle trigger squeezed, press the fast idle

lock. Release the throttle lock--out and trig-

ger while holding the fast idle lock button.

CHOKE KNOB

The CHOKE KNOB activates the choke to

provide additional fuel to the engine during

cold starting.

CHAIN BRAKE

The CHAIN BRAKE is a device designed to

stop the chain if kickback occurs. The chain

brake activates automatically in the event of

kickback. The chain brake activates manu-

ally if the front hand guard is pushed forward.

The chain brake is disengaged by pulling the

front hand guard back toward the front han-

dle as far as possible.

CHAIN TENSION

It is normal for a new chain to stretch during first

30 minutes of operation. You should check

your chain tension frequently. See CHAIN

TENSION under the SERVICE AND AD-

JUSTMENTS section.

FUELING & LUBRICATION

FUELING ENGINE

This engine is certified to operate on

unleaded gasoline. Before operation,

gasoline must be mixed with a good quality

2-cycle air-cooled engine oil. We

recommend Poulan or Poulan Pro

brand

oil. If you do not use this oil, use a good

quality 2-cycle air-cooled oil designed to be

mixed at a ratio of 40:1 (A 40:1 ratio is

obtained by mixing 3.2 onces of oil with 1

gallon of unleaded gasoline). DO NOT USE

automotive or boat oil. These oils will cause

engine damage. When mixing fuel follow the

instructions printed on the container. Always

read and follow the safety rules listed under

HANDLE FUEL WITH CAUTION.

BAR AND CHAIN LUBRICATION

The bar and chain require continuous lu-

brication. Lubrication is provided by the auto-

matic oiler system when the oil tank is kept

filled. Lack of oil will quickly ruin the bar and

chain. Too little oil will cause overheating

shown by smoke coming from the chain and/

or discoloration of the bar.

In freezing weather oil will thicken, making it

necessary to thin bar and chain oil with a

small amount (5 to 10%) of #1 Diesel Fuel or

kerosene. Bar and chain oil must be free

flowing for the oil system to pump enough oil

for adequate lubrication.

Genuine Poulan or Poulan Pro

bar and

chain oil is recommended to protect your unit

against excessive wear from heat and

friction. Poulan or Poulan Pro

oil resists

high temperature thinning. If Poulan or

Poulan Pro

bar and chain oil is not

available, use a good grade SAE 30 oil.

Never use waste oil for bar and chain lubri-

cation.

Always stop the engine before removing

the oil cap.

Oil Cap

Fuel mix cap

IMPORTANT

Experience indicates that alcohol--blended

fuels (called gasohol or using ethanol or

methanol) can attract moisture which leads

to separation and formation of acids during

storage. Acidic gas can damage the fuel

system of an engine while in storage. To

avoid engine problems, the fuel system

should be emptied before storage for 30

days or longer. Drain the gas tank, start the

engine and let it run until the fuel lines and

carburetor are empty. Use fresh fuel next

season. See STORAGE section for addi-

tional information.

STARTING

WARNING:

The chain must not

move when the engine runs at idle speed. If

the chain moves at idle speed refer to CAR-

BURETOR ADJUSTMENT within this

manual. Avoid contact with the muffler. A hot

muffler can cause serious burns.

To stop the engine move the ON/STOP

switch to the STOP position.

To start the engine hold the saw firmly on

the ground as illustrated. Make sure the

chain is free to turn without contacting any

object.

Hold saw firmly while pulling starter rope

Use only 15”--18” of rope per pull.

Left hand

on front

handle

Starter rope handle

Right foot through rear handle

IMPORTANT POINTS TO REMEMBER

When pulling the starter rope, do not use the

full extent of the rope as this can cause the

rope to break. Do not let starter rope snap

back. Hold the handle and let the rope rewind

slowly.

For cold weather starting, start the unit at

FULL CHOKE; allow the engine to warm up

before squeezing the throttle trigger.

NOTE

: Do not cut material with the choke/

fast idle lever at the FULL CHOKE position.

STARTING A COLD ENGINE (or a

warm engine after running out of

fuel)

Move ON/STOP switch to the ON position.

Pull the choke/fast idle lever out to the full

extent.

ON/STOP

SWITCH

STOP

OFF FULL

CHOKE/FAST IDLE LEVER

Choke/Fast

Idle Lever

(SIDE VIEW)

Press the throttle lock with your right hand.

Squeeze and hold the throttle trigger;

Press and hold the fast idle lock with your

forefinger; release the throttle trigger.

NOTE

: If the throttle trigger is squeezed

during starting, it will be necessary to reset

the fast idle lock.

Pull the starter rope quickly with your right

hand a maximum of 10 times.

Push the choke/fast idle lever in complete-

ly (to the OFF CHOKE position).

Pull the starter rope quickly with your right

hand until the engine starts.

Allow the engine to run for approximately 5

seconds. Then, squeeze and release the

throttle trigger to allow engine to return to

idle speed.

STARTING A WARM ENGINE:

Move ON/STOP switch to the ON position.

Press the throttle lock with your right hand.

Squeeze and hold the throttle trigger;

Press and hold the fast idle lock with your

forefinger; release the throttle trigger.

Be sure choke/fast idle lever is in the OFF

CHOKE position.

Pull the starter rope quickly with your right

hand until the engine starts.

Squeeze and release the throttle trigger to

allow engine to return to idle speed.

DIFFICULT STARTING (or starting a

flooded engine)

The engine may be flooded with too much

fuel if it has not started after 10 pulls.

Flooded engines can be cleared of excess

fuel by following the warm engine starting

procedure listed above. Insure the ON/

STOP switch is in the ON position.

Starting could require pulling the starter rope

handle many times depending on how badly

the unit is flooded. If engine fails to start refer

to the TROUBLESHOOTING TABLE or call

1--800--554--6723.

CHAIN BRAKE

WARNING:

WE DO NOT REP-

RESENT AND YOU SHOULD NOT AS-

SUME THAT THE CHAIN BRAKE WILL

PROTECT YOU IN THE EVENT OF A

KICKBACK. Kickback is a lightning fast ac-

tion which throws the bar and rotating chain

back and up toward the operator. Kickback

can be caused by allowing contact of the bar

tip in the danger zone with any hard object.

Kickback can also be caused by pinching the

saw chain along the top of the guide bar. This

action may push the guide bar rapidly back

toward the operator. Either of these events

may cause you to lose control of the saw

which could result in serious injury or even

death. DO NOT RELY UPON ANY OF THE

SAFETY DEVICES BUILT INTO YOUR

SAW. YOU SHOULD USE THE SAW

PROPERLY AND CAREFULLY TO AVOID

KICKBACK. Reduced--kickback guide bars

and low--kickback saw chains reduce the

chance and magnitude of kickback and are

recommended. Your saw has a low kick-

back chain and bar as original equipment. If

the brake band is worn too thin it may break

when the chain brake is triggered. With a

broken brake band, the chain brake will not

stop the chain. The chain brake should be re-

placed by an authorized service dealer if any

part is worn to less than 1/32” thick. Repairs

on a chain brake should be made by an au-

thorized service dealer. Take your unit to the

place of purchase if purchased from a ser-

vicing dealer, or to the nearest authorized

master service dealer.

This saw is equipped with a chain brake.

The brake is designed to stop the chain if

kickback occurs.

The inertia--activated chain brake is

activated if the front hand guard is pushed

forward, either manually (by hand) or

automatically (by sudden movement).

If the brake is already activated, it is

disengaged by pulling the front hand guard

back toward the front handle as far as

possible.

When cutting with the saw, the chain brake

must be disengaged.

Disengaged

Engaged

Braking function control

CAUTION:

The chain brake must be

checked several times daily. The engine

must be running when performing this proce-

dure. This is the only instance when the saw

should be placed on the ground with the en-

gine running.

Place the saw on firm ground. Hold the han-

dles with both hands and apply full throttle.

Activate the chain brake by turning your left

wrist against the hand guard without releas-

ing your grip around the front handle. The

chain should stop immediately.

Inerti a act ivating funct ion contro l

WARNING:

When performing the

following procedure, the engine must be

turned off.

Hold the chain saw approximately 14” (35

cm) above a stump or other wooden surface.

Release your grip on the front handle and

use the weight of the saw to let the top of the

guide bar fall forward and contact the stump.

When the tip of the bar hits the stump, the

brake should activate.

CUTTING METHODS

IMPORTANT POINTS

Check chain tension before first use and

after 1 minute of operation. See CHAIN

TENSION in the ASSEMBLY section.

Cut wood only. Do not cut metal, plastics,

masonry, non-wood building materials, etc.

Stop the saw if the chain strikes a foreign

object. Inspect the saw and repair parts as

necessary.

Keep the chain out of dirt and sand. Even a

small am ount of dirt will quickly dull a chain

and incre as e the possibility of kickback .

Practice cutting a few small logs us-

ing the following techniques to get

the “feel” of using your saw before

you begin a major sawing operation.

Squeeze the throttle trigger and al-

low the engine to reach full speed

before cutting.

Begin cutting with the saw frame

against the log.

Keep the engine at full speed the en-

tire time you are cutting.

Allow the chain to cut for you. Exert

only light downward pressure.

Release the throttle trigger as soon

as the cut is completed, allowing the

engine to idle. If you run the saw at

full throttle without a cutting load, un-

necessary wear can occur.

To avoid losing control when cut is

complete, do not put pressure on

saw at end of cut.

Stop the engine before setting the saw

down.

TREE FELLING TECHNIQUES

WARNING:

Check for broken or

dead branches which can fall while cutting

causing serious injury. Do not cut near build-

ings or electrical wires if you do not know the

direction of tree fall, at night since you will not

be able to see well, or during bad weather

such as rain, snow, or strong winds, etc.

Carefully plan your sawing operation in ad-

vance.

Clear the work area. You need a clear area

all around the tree so you can have secure

footing.

Study the natural conditions that can

cause the tree to fall in a particular direc-

tion.

Natural conditions that can cause a tree to

fall in a particular direction include:

The wind direction and speed.

The lean of the tree. The lean of a tree

might not be apparent due to uneven or

sloping terrain. Use a plumb or level to de-

termine the direction of tree lean.

Weight and branches on one side.

Surrounding trees and obstacles.

Look for decay and rot. If the trunk is rotted,

it can snap and fall toward the operator.

Make sure there is enough room for the tree to

fall. Maintain a distance of

2-1/2

tree lengths

from the nearest person or other objects. En-

gine noise can drown out a warning call.

Remove dirt, stones, loose bark, nails, sta-

ples, and wire from the tree where cuts are to

be made.

Direction of Fall

Plan a clear retreat path

FELLING LARGE TREES

(6 inches in diameter or larger)

The notch method is used to fell large trees.

A notch is cut on the side of the tree in the de-

sired direction of fall. After a felling cut is

made on the opposite side of tree, the tree

will tend to fall into the notch.

NOTE

: If the tree has large buttress roots,

remove them before making the notch.

NOTCH CUT AND FELLING THE

TREE

Make notch cut by cutting the top of the

notch first. Cut through

1/3

of the diameter

of the tree. Next complete the notch by cut-

ting the bottom of the notch. See illustra-

tion. Once the notch is cut remove the

notch of wood from the tree.

After removing the cutout of wood, make

the felling cut on the opposite side of the

notch. This is done by making a cut about

two inches higher than the center of the

notch. This will leave enough uncut wood

between the felling cut and the notch to

form a hinge. This hinge will help prevent

the tree from falling in the wrong direction.

Notch

First cut

Second cut

Final cut here 2 inches

above center of notch.

Opening

of felling

cut

Closing of

notch

Hinge holds tree on stump and helps

control fall

NOTE

: Before felling cut is complete, use

wedges to open the cut when necessary to

control the direction of fall. To avoid kickback

and chain damage, use wood or plastic

wedges, but never steel or iron.

Be alert to signs that the tree is ready to

fall: cracking sounds, widening of the fell-

ing cut, or movement in the upper

branches.

As tree starts to fall, stop saw, put it down,

and get away quickly on your planned re-

treat path.

Be extremely cautious with partially fallen

trees that may be poorly supported. When

a tree doesn’t fall completely, set the saw

aside and pull down the tree with a cable

winch, block and tackle, or tractor. To

avoid injury, do not cut down a partially fall-

en tree with your saw.

CUTTING A FALLEN TREE

(BUCKING)

Bucking is the term used for cutting a fallen

tree to the desired log length.

WARNING:

Do not stand on the log

being cut. Any portion can roll causing loss of

footing and control. Do not stand downhill of

the log being cut.

IMPORTANT POINTS

Cut only one log at a time.

Cut shattered wood very carefully; sharp

pieces of wood could be flung toward oper-

ator.

Use a sawhorse to cut small logs. Never

allow another person to hold the log while

cutting and never hold the log with your leg

or foot.

Do not cut in an area where logs, limbs,

and roots are tangled. Drag the logs into a

clear area before cutting by pulling out ex-

posed and cleared logs first.

TYPES OF CUTTING USED FOR

BUCKING

WARNING:

If saw becomes pinched

or hung in a log, don’t try to force it out. You

can lose control of the saw resulting in injury

and/or damage to the saw. Stop the saw,

drive a wedge of plastic or wood into the cut

until the saw can be removed easily. Restart

the saw and carefully reenter the cut. Do not

attempt to restart your saw when it is pinched

or hung in a log.

Turn saw

OFF

and use a plastic or

wooden wedge to force cut open.

Use a wedge to remove pinched saw

Overcutting begins on the top side of the log

with the saw against the log. When overcut-

ting use light downward pressure.

Overcutting Undercutting

Undercutting involves cutting on the under-

side of the log with top of saw against the log.

When undercutting use light upward pres-

sure. Hold saw firmly and maintain control.

The saw will tend to push back toward you.

WARNING:

Never turn saw upside

down to undercut. The saw cannot be con-

trolled in this position.

Always make your first cut on the compres-

sion side of the log. The compression side of

the log is where the pressure of the log’s

weight is concentrated.

Second cut

First cut on compression side of log

Second cut

BUCKING WITHOUT A

SUPPORT

Overcut through 1/3 of the diameter of log.

Roll log over; finish with a second overcut.

Watch for saws with a compression side to

prevent the saw from pinching. See il-

lustration for cutting logs with a compres-

sion side.

BUCKING USIN G A LOG OR SUP-

PORT STAND

Remember your first cut is always on the

compression side of the log.

Your first cut should extend

1/3

of the

diameter of the log.

Finish with your second cut.

Cut

Usingalogforsupport

Cut

Using a support stand

Cut

LIMBING AND PRUNING

WARNING:

Be alert for and guard

against kickback. Do not allow the moving

chain to contact any other branches or ob-

jects at the nose of the guide bar when limb-

ing or pruning. Allowing such contact can re-

sult in serious injury.

WARNING:

Neverclimbintoatreeto

limb or prune. D o not stand on ladders, plat-

forms, a log, or in any position which can cause

you to lose your balance or control of the saw .

IMPORTANT POINTS

Work slowly, keeping both hands firmly

gripped on saw. Maintain secure footing

and balance.

Watch out for springpoles. Use extreme

caution when cutting small size limbs. Slen-

der material may catch saw chain and be

whipped toward you or pull you off balance.

Be alert for springback. Watch out for

branches that are bent or under pressure.

Avoid being struck by the branch or the

saw when the tension in the wood fibers is

released.

Frequently clear branches out of the way

to avoid tripping over them.

LIMBING

Always limb a tree after it is cut down. Only

then can limbing be done safely and prop-

erly.

Leave the larger limbs underneath the

felled tree to support the tree as you work.

Start at base of the felled tree and work to-

ward the top, cutting branches and limbs.

Remove small limbs with one cut.

Keep the tree between you and the chain

as much as possible.

Remove larger, supporting branches with

the

1/3

2/3

cutting techniques described in

BUCKING WITHOUT A SUPPORT.

Always use an overcut to cut small and

freely hanging limbs. Undercutting could

cause limbs to fall and pinch saw.

PRUNING

WARNING:

Limit pruning to limbs

shoulder height or below. Do not cut if

branches are higher than your shoulder. Get

a professional to do the job.

Make your fist cut

1/3

of the way through

the bottom of the limb.

Next make a 2nd cut all the way through

the limb. Then cut a third overcut leaving a

1 to 2 inch collar from the trunk of the tree.

First cut

Second cut

Third cut

Collar

Pruning technique

SERVICE

WARNING:

Disconnect the spark

plug before performing maintenance except

for carburetor adjustments.

We recommend all service and adjustments

not listed in this manual be performed by an

Authorized or Master Service Dealer.

MAINTENANCE SCHEDULE

Lubricate bar

sprocket hole After each use.......

Check:

Fuel mixture level Before each use....

Bar lubrication Before each use.......

Chain tension Before each use.......

Chain sharpness Before each use....

For damaged parts Before each use..

For loose caps Before each use......

For loose fasteners Before each use...

For loose parts Before each use......

Inspect and Clean:

Bar Before each use................

Complete saw After each use.......

Air filter Every 5 hours*.............

Chain brake Every 5 hours*........

Spark arresting screen

and muffler Every 25 hours*.........

Replace spark plug

Yearly.

Replace fuel filter

Yearly...

* Hours of Operation

AIR FILTER

CAUTION:

Do not clean filter in gasoline or

other flammable solvent to avoid creating a

fire hazard or producing harmful evapora-

tive emissions.

Cleaning the air filter:

A dirty air filter decreases engine perform-

ance and increases fuel consumption and

harmful emissions. Always clean after every

5 hours of operation.

Clean the cover and the area around it to

keep dirt and sawdust from falling into the

carburetor chamber when the cover is re-

moved.

Remove the parts as illustrated.

Wash the filter in soap and water.

Replace parts.

INSPECT MUFFLER AND SPARK

ARRESTING SCREEN

As the unit is used, carbon deposits build up

on the muffler and spark arresting screen,

and must be removed to avoid creating a fire

hazard or affecting engine performance.

Replace the spark arresting screen if breaks

occur.

Spark Arrestor

Screen

CLEANING THE SPARK ARREST-

ING SCREEN

Clean every 25 hours of operation or annually ,

whichever comes first.

Loosen and remove the muffler cover

screws.

Remove the muffler cover (cover snaps off

muffler body).

Remove muffler diffuser and spark arrest-

ing screen assembly. Notice the orienta-

tion of parts for reassembly.

Clean the spark arresting screen with a

wire brush. Replace screen if breaks are

found.

Replace any broken or cracked muffler

parts.

Reinstall diffuser and spark arresting

screen assembly with holes facing up and

toward muffler cover.

Reinstall muffler cover and screws (7-8 ft-

lbs.).

CARBURETOR ADJUSTMENTS

Your carburetor is equipped with limiter

caps. Carburetor adjustment is a compli-

cated task. We recommend that you take

your unit to an Authorized Service Dealer.

Damage will occur if you turn the needles be-

yond the limiter stops.

BAR MAINTENANCE

If your saw cuts to one side, has to be forced

through the cut, or been run with an improper

amount of bar lubrication it may be neces-

sary to service your bar. A worn bar will dam-

age your chain and make cutting difficult.

After each use, ensure ON/STOP switch is

in the STOP position, then clean all sawdust

from the guide bar and sprocket hole.

To maintain guide bar:

Move ON/STOP switch to the STOP posi-

tion.

Loosen and remove chain brake nuts and

chain brake. Remove bar and chain from

saw.

Clean the oil holes and bar groove after

each 5 hours of operation.

Remove Sawdust From

Guide Bar Groove

Sprocket Hole

Oil Holes

Add lubricant to sprocket hole after each

use.

Burring of guide bar rails is a normal pro-

cess of rail wear. Remove these burrs with

a flat file.

When rail top is uneven, use a flat file to re-

store square edges and sides.

Correct GrooveWorn Groove

File Rail Edges

and Sides

Square

Replace guide bar when the groove is worn,

the guide bar is bent or cracked, or when

excess heating or burring of the rails occurs.

If replacement is necessary, use only the

guide bar specified for your saw in the repair

parts list or on the decal located on the chain

saw.

CHAIN SHARPENING

Chain sharpening is a complicated task that

requires special tools. We recommended

you refer chain sharpening to a professional

chain sharpener.

IGNITION TIMING

Ignition timing is fixed and nonadjustable.

SPARK PLUG

The spark plug should be replaced each

year to ensure the engine starts easier and

runs better.

Loosen and remove the screws on the cyl-

inder cover.

Remove the cylinder cover.

Pull off the spark plug boot.

Remove spark plug from cylinder and dis-

card.

Replace with Champion RCJ--7Y spark

plug and tighten with a 3/4 inch socket

wrench (10-12 ft-lbs). Spark plug gap

should be 0.025 inches.

Reinstall the spark plug boot.

Reinstall the cylinder cover and screws

(15-20 in-lbs).

Spark

Plug

Cylinder

Cover

STORAGE

WARNING:

Stop engine and allow to

cool, and secure the unit before storing or

transporting in a vehicle. Store unit and fuel

in an area where fuel vapors cannot reach

sparks or open flames from water heaters,

electric motors or switches, furnaces, etc.

Store unit with all guards in place. Position so

that any sharp object cannot accidentally

cause injury to passersby. Store the unit out

of reach of children.

Before storing, drain all fuel from the unit.

Start engine and allow to run until it stops.

Clean the unit before storing. Pay particu-

lar attention to the air intake area, keeping

it free of debris. Use a mild detergent and

sponge to clean the plastic surfaces.

Do not store the unit or fuel in a closed area

where fuel vapors can reach sparks or an

open flame from hot water heaters, electric

motors or switches, furnaces, etc.

Store in a dry area out of reach of children.

CAUTION:

It is important to prevent gum

deposits from forming in essential fuel sys-

tem parts such as the carburetor, fuel filter,

fuel hose, or fuel tank during storage. Alco-

hol blended fuels (called gasohol or using

ethanol or methanol) can attract moisture

which leads to fuel mixture separation and

formation of acids during storage. Acidic gas

can damage the engine.

NEED ASSISTANCE?

Need Assistance?

Call 1--800--554--6723.

Need a Service Part?

Contact your dealer.

TROUBLE CAUSE REMEDY

Engine will not

start or will run

only a few

seconds after

starting.

Ignition switch off.

Engine flooded.

Fuel tank empty.

Spark plug not firing.

Fuel not reaching

carburetor..

Move ignition switch to ON.

See “Difficult Starting” in

Operation Section.

Fill tank with correct fuel mixture.

Install new spark plug.

Check for dirty fuel filter; replace.

Check for kinked or split fuel line;

repair or replace.

Engine will

not idle

properly.

Carburetor requires

adjustment.

Crankshaft seals worn.

Contact an Authorized Service Dealer.

Air filter dirty.

Spark plug fouled.

Carburetor requires

adjustment.

Engine will not

accelerate,

lacks power,

or dies under

a load.

Clean or replace air filter.

Clean or replace plug

and regap.

Contact an Authorized Service Dealer.

Engine

smokes

excessively.

Toomuchoilmixedwith

gasoline..

Empty fuel tank and refill with

correct fuel mixture..

WARNING:

Always stop unit and disconnect spark plug before performing all of

the recommended remedies below except remedies that require operation of the unit.

TROUBLESHOOTING TABLE

LIMITED WARRANTY

ELECTROLUX HOME PRODUCTS

NORTH AMERICA, Division of WCI Out-

door Products, Inc., warrants to the original

purchaser that each new Poulan or Poulan

Pro brand gasoline chain saw is free from de-

fects in material and workmanship and

agrees to repair or replace under this war-

ranty any defective gasoline chain saw as

follows from the original date of purchase.

2 YEARS -- Parts and Labor, when used for

Household purposes.

60 DAYS -- Parts and Labor, when used for

Commercial, Professional, or Income Pro-

ducing purposes.

30 DAYS -- Parts and Labor, if used for rental

purposes.

This warranty is not transferable and does

not cover damage or liability caused by im-

proper handling, improper maintenance, or

the use of accessories and/or attachments

not specifically recommended by ELEC-

TROLUX HOME PRODUCTS NORTH

AMERICA for this chain saw. Additionally,

this warranty does not cover damage

caused by improper handling, improper

maintenance, or if the saw is altered in any

way which in our judgement affects its condi-

tion or operation. This warranty does not

cover tune--up, spark plugs, filters, starter

ropes, starter springs, chain sharpening,

bars, chains, and other parts which wear and

require replacement with reasonable use

during the warranty period. This warranty

does not cover predelivery set--up, installa-

tion of guide bar and chain, and normal ad-

justments explained in the operator’s manu-

al such as carburetor adjustments and chain

tension adjustments. This warranty does

not cover transportation costs.

THIS WARRANTY GIVES YOU SPECIFIC

LEGAL RIGHTS, AND YOU MAY HAVE

OTHER RIGHTS WHICH VAR Y FROM

STATE TO STATE.

NO CLAIMS FOR CONSEQUENTIAL OR

OTHER DAMAGES WILL BE ALLOWED,

AND THERE ARE NO OTHER EXPRESS

WARRANTIES EXCEPT THOSE EX-

PRESSLY STIPULATED HEREIN.

SOME STATES DO NOT ALLOW LIMITA-

TIONS ON HOW LONG AN IMPLIED WAR-

RANTY LASTS OR THE EXCLUSION OR

LIMITATIONS OF I NCIDENTAL OR CON-

SEQUENTIAL DAMAGES, SO THE

ABOVE LIMITATIONS OR EXCLUSION

MAYNOTAPPLYTOYOU.

ELECTROLUX HOME PRODUCTS

NORTH AMERICA’S policy is to continu-

ously improve its products. Therefore,

ELECTROLUX HOME PRODUCTS

NORTH AMERICA reserves the right to

change, modify, or discontinue models, de-

signs, specifications, and accessories of all

products at any time without notice or obliga-

tion to any purchaser.

U.S. EPA

EMISSION CONTROL

WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OB-

LIGATIONS: The U. S. Environmental

Protection Agency and Poulan/Weed Eater,

Division of WCI Outdoor Products are

pleased to explain the emissions control

system warranty on your lawn and garden

equipment engine. All new utility and lawn

and garden equipment engines must be de-

signed, built, and equipped to meet the strin-

gent anti--smog standards. Poulan/Weed

Eater must warrant the emission control sys-

tem on your lawn and garden equipment en-

gine for the periods of time listed below pro-

vided there has been no abuse, neglect, or

improper maintenance of your lawn and gar-

den equipment engine. Your emission con-

trol system includes parts such as the carbu-

retor and the ignition system. Where a

warrantable condition exits, Poulan/Weed

Eater will repair your lawn and garden equip-

ment engine at no cost to you. Expenses

covered under warranty include diagnosis,

parts and labor. MANUFACTURER’S

WARRANTY COVERAGE: If any emis-

sions related part on your engine (as listed

under Emissions Control Warranty Parts

List) is defective or a defect in the materials

or workmanship of the engine causes the

failure of such an emission related part, the

part will be repaired or replaced by Poulan/

Weed Eater. OWNER’S WARRANTY RE-

SPONSIBILITIES: As the lawn and garden

equipment engine owner, you are responsi-

ble for the performance of the required main-

tenance listed in your Owner’s Manual. Pou-

lan/Weed Eater recommends that you retain

all receipts covering maintenance on your

lawn and garden equipment engine, but Pou-

lan/Weed Eater cannot deny warranty solely

for the lack of receipts or for y our failure to

ensure the performance of all scheduled

maintenance. As the lawn and garden

equipment engine owner, you should be

aware that Poulan/Weed Eater may deny

you warranty coverage if your lawn and gar-

den equipment engine or a part of it has failed

due to abuse, neglect, improper mainte-

nance, unapproved modifications, or the use

of parts not made or approved by the original

equipment manufacturer. You are responsi-

ble for presenting your lawn and garden

equipment engine to a Poulan/Weed Eater

authorized repair center as soon as a prob-

lem exists. Warranty repairs should be com-

pleted in a reasonable amount of time, not to

exceed 30 days. If you have any questions

regarding your warranty rights and responsi-

bilities, you should contact your nearest au-

thorized service center or call Poulan/Weed

Eater at 1--800--554--6723.

WARRANTY COMMENCEMENT DATE:

The warranty period begins on the date the

lawn and garden equipment engine is pur-

chased. LENGTH OF COVERAGE: This

warranty shall be for a period of two years

from the initial date of purchase. WHAT IS

COVERED: REPAIR OR REPLACEMENT

OF PARTS. Repair or replacement of any

warranted part will be performed at no

charge to the owner at an approved Poulan/

Weed Eater servicing center. If you have any

questions regarding your warranty rights

and responsibilities, you should contact your

nearest authorized service center or call

Poulan/Weed Eater at 1--800--554--6723

WARRANTY PERIOD: Any warranted part

which is not scheduled for replacement as

required maintenance, or which is sched-

uled only for regular inspection to the effect

of “repair or replace as necessary” shall be

warranted for 2 years. Any warranted part

which is scheduled for replacement as re-

quired maintenance shall be warranted for

the period of time up to the first scheduled re-

placement point for that part. DIAGNOSIS:

The owner shall not be charged for diagnos-

tic labor which leads to the determination that

a warranted part is defective if the diagnostic

work is performed at an approved Poulan/

Weed Eater servicing center. CONSE-

QUENTIAL DAMAGES: Poulan/Weed Eat-

er may be liable for damages to other engine

components caused by the failure of a war-

ranted part still under warranty. WHAT IS

NOT COVERED: All failures caused by

abuse, neglect, or improper maintenance

are not covered. ADD--ON OR MODIFIED

PARTS: The use of add--on or modified parts

can be grounds for disallowing a warranty

claim. Poulan/Weed Eater is not liable to cov-

er failures of warranted parts caused by the

use of add--on or modified parts. HOW TO

FILE A CLAIM: If you have any questions

regarding your warranty rights and responsi-

bilities, you should contact your nearest au-

thorized service center or call Poulan/Weed

Eater at 1--800--554--6723 . WHERE TO

GET WARRANTY SERVICE: War r anty ser-

vices or repairs shall be provided at all Poulan/

Weed Eater service centers. call:

1--800--554--6723 MAINTENANCE, RE-

PLACEMENT AND REPAIR OF EMISSION

RELATED PARTS:AnyPoulan/Weed Eater

approved replacement part used in the per-

formance of any warranty maintenance or

repair on emission related parts will be pro-

vided without charge to the owner if the part

is under warranty. EMISSION CONTROL

WARRANTY PARTS LIST: Carburetor,

Ignition System: Spark Plug (covered up to

maintenance schedule), Ignition Module.

MAINTENANCE STATEMENT : The owner

is responsible for the performance of all re-

quired maintenance as defined in the own-

er’s manual.

Poulan 530088788 User manual

Brand: Poulan

Model: 530088788

Category: Power chainsaws

Type: User manual

This manual is also suitable for

3450
3750

Download PDF

report

Poulan 530088788 User manual

This manual is also suitable for

Poulan 530088788 User manual

Related papers

Other documents